Effect of amorphous silica and silica sand on removal of chromium(VI) by zero-valent iron

The effect of two surfaces (amorphous silica and silica sand) on the reduction of chromium(VI) by zero-valent iron (Fe(0)) was investigated using batch reactors. The amendment of both surfaces significantly increased the rate and extent of Cr(VI) removal. The rate enhancement by amended surfaces is presumed to result from scavenging of Fe(0)-Cr(VI) reaction products by the provided surfaces, which minimized surface deactivation of Fe(0). The rate enhancing effect was greater for silica compared to sand, and the difference is attributed to silica's higher surface area, greater affinity for reaction products and pH buffering effect. For a given mass of Fe(0), the reactivity and longevity of Fe(0) to treat Cr(VI) increased with increasing dose of silica. Elemental analyses of the reacted iron and silica revealed that chromium removed from the solution was associated with both surfaces, with its mass distribution being approximately 1:1 per mass of iron and silica. The overall result suggests reductive precipitation was a predominant Cr(VI) removal pathway, which involves initial reduction of Cr(VI) to Cr(III), followed by formation of Cr(III)/Fe(III) hydroxides precipitates.     

Waste Fe(III)/Cr(III) hydroxide as adsorbent for the removal of Cr(VI) from aqueous solution and chromium plating industry wastewater

Fe(III)/Cr(III) hydroxide, a waste material from the fertilizer industry, has been used for the adsorption of Cr(VI) from aqueous solution, over a range of initial metal ion concentrations (5-30 mg litre(-1)), agitation times (1-180 min), adsorbent dosages (100-1200 mg per 50 ml), temperatures (24, 29 and 38 degrees C) and pH values (4.5-10). The adsorption of Cr(VI) increased with the initial concentration of Cr(VI) and with temperature. The process of uptake follows both the Langmuir and the Freundlich isotherm models. The applicability of Lagergren and empirical kinetic models has also been investigated. Almost quantitative removal of Cr(VI) at 10 mg litre(-1) in a 50-ml solution by 500 mg of adsorbent was found at an equilibrium pH of 5.6. The efficiency of chromium removal was also tested using wastewater from the chromium plating industry.     

Accumulation and remobilization of aqueous chromium(VI) at iron oxide surfaces: Application of a thin-film continuous flow-through reactor

A thin-film continuous flow-through reactor was used to investigate reactions between aqueous Cr(VI) and two iron oxides, geothite and magnetite. Delayed effluent breakthrough of Cr(VI) indicated significant uptake by both oxides. Accumulation and remobilization of Cr(VI) depends on pH and the redox properties of the surface. For geothite the surface was quickly saturated and no further adsorption observed. Chromate anion (CrO₄²⁻) exhibited Langmuir-type adsorption. For magnetite, a significant slow steady-state rate of Cr(VI) uptake was observed. We propose two different mechanisms of chromium uptake: surface complexation of Cr(VI) species on geothite, and reductive precipitation of Cr(VI) at Fe(II) sites on magnetite.     

Chromium transport, oxidation, and adsorption in manganese-coated sand

We examine how the processes of advection, dispersion, oxidation-reduction, and adsorption combine to affect the transport of chromium through columns packed with pyrolusite (beta-MnO2)-coated sand. We find that beta-MnO2 effectively oxidizes Cr(III) to Cr(VI) and that the extent of oxidation is sensitive to changes in pH, pore water velocity, and influent concentrations of Cr(III). Cr(III) oxidation rates, although initially high, decline well before the supply of beta-MnO2 is depleted, suggesting that a reaction product inhibits the conversion of Cr(III) to Cr(VI). Rate-limited reactions govern the weak adsorption of each chromium species, with Cr(III) adsorption varying directly with pH and Cr(VI) adsorption varying inversely with pH. The breakthrough data on chromium transport can be matched closely by calculations of a simple model that accounts for (1) advective-dispersive transport of Cr(III), Cr(VI), and dissolved oxygen, (2) first-order kinetics adsorption of the reduced and oxidized chromium species, and (3) nonlinear rate-limited oxidation of Cr(III) to Cr(VI). Our work supplements the limited database on the transport of redox-sensitive metals in porous media and provides a means for quantifying the coupled processes that contribute to this transport.     

Use of waste iron metal for removal of Cr(VI) from water

Cr(VI) removal from water was evaluated using waste iron particles in batch experimental mode. The reaction rates were inversely proportional to the initial Cr(VI) concentrations, and the reaction rates of Cr(VI) removal with the waste iron metal were faster than those with Peerless iron, a commercial zero-valent iron. The loss in iron reactivity due to the oxidation, from Fe(0) to Fe(II), ultimately to Fe(III), could be recovered by adding iron-reducing consortium (IRC) to the oxidized iron. Bacterial reduction of Cr(VI) also helped to decrease the aqueous concentration of Cr(VI), but the reduction of oxidized iron by IRC and the consequent reduction of Cr(VI) to Cr(III) by the reduced iron was more significant. Thus, reusing waste iron metal for Cr(VI) removal can reduce the cost of reactive media. Furthermore, the addition of IRC to the waste iron metal can accelerate the removal rate of Cr(VI), and can recover the reactivity of irons which were oxidized by Cr(VI).     

Performance evaluation of granular iron for removing hexavalent chromium under different geochemical conditions

Long-term column experiments were conducted under different geochemical conditions to estimate the longevity of Fe 0 permeable reactive barriers (PRBs) treating hexavalent chromium (Cr(VI)). Secondary carbonate minerals were precipitated, and their effects on the performance, such as differences in the mechanism for Cr removal and the changes in system hydraulics, were assessed. Sequestration of Cr(VI) occurred primarily by precipitation of Fe(III)-Cr(III) (oxy)hydroxides. Trace amounts of Cr were observed in iron hydroxy carbonate presumably due to substitution of Cr3+ for Fe3+. The formation of Fe(III)-Cr(III) (oxy)hydroxide greatly decreased the reactivity of the Fe 0 and thus resulted in migration of the Cr removal front. Carbonate minerals did not appear to contribute to further passivation with regard to reactivity toward Cr removal; rather, the column receiving high contents of dissolved calcium carbonate showed slightly enhanced Cr removal by means of a higher corrosion rate of Fe 0 and because of sequestration by an iron hydroxy carbonate. Precipitation of carbonates, however, governed other geochemical parameters. The porosity and hydraulic conductivity in the column receiving high contents of dissolved calcium carbonate did not indicate a great loss in system permeability because the accumulation of carbonates declined as the Fe 0 was passivated over time. However, the accumulated carbonates and associated Fe(III)-Cr(III) (oxy)hydroxide could cause problems because the presence of these solids resulted in a decline in flow rate after about 1400 pore volumes of operation.     

Influence of complex reagents on removal of chromium(VI) by zero-valent iron

The removal of Cr(VI) by zero-valent iron (Fe(0)) and the effect of three complex reagents, ethylenediaminetetraacetic acid (EDTA), NaF and 1,10-phenanthroline, on this reaction were investigated using batch reactors at pH values of 4, 5 and 6. The results indicate that the removal of Cr(VI) by Fe(0) is slow at pH 5.0 and that three complex reagents play different roles in the reaction. EDTA and NaF significantly enhance the reaction rate. The zero-order rate constants at pH 5.0 were 5.44 microM min(-1) in the presence of 4mM EDTA and 0.99 micrM min(-1) in the presence of 8 mM NaF, respectively, whereas that of control was only 0.33 micrM min(-1), even at pH=4.0. This enhancement is attributed to the formation of complex compounds between EDTA/NaF and reaction products, such as Cr(III) and Fe(III), which eliminate the precipitates of Cr(III), Fe(III) hydroxides and Cr(x)Fe(1-)(x)(OH)(3) and thus reduce surface passivation of Fe(0). In contrast, 1,10-phenanthroline, a complex reagent for Fe(II), dramatically decreases Cr(VI) reduction by Fe(0). At pH=4.0, the zero-order rate constant in the presence of 1mM of 1,10-phenanthroline was 0.02 micrM min(-1), decreasing by 99.7% and 93.9%, respectively, compared with the results in the presence and absence of EDTA. The results suggest that a pathway of the reduction of Cr(VI) to Cr(III) by Fe(0) may involve dissolution of Fe(0) to produce Fe(II), followed by reduction of Cr(VI) by Fe(II), rather than the direct reaction between Cr(VI) and Fe(0), in which Fe(0) transfers electrons to Cr(VI).     

Comparative study of chromium biosorption by red, green and brown seaweed biomass

Dried biomass of the macroalgae Fucus vesiculosus and Fucus spiralis (brown), Ulva spp. (comprising Ulva linza, Ulva compressa and Ulva intestinalis) and Ulva lactuca (green), Palmaria palmata and Polysiphonia lanosa (red) were studied in terms of their chromium biosorption performance. Metal sorption was highly pH dependent with maximum Cr(III) and Cr(VI) sorption occurring at pH 4.5 and pH 2, respectively. Extended equilibrium times were required for Cr(VI) binding over Cr(III) binding (180 and 120min, respectively) thus indicating possible disparities in binding mechanism between chromium oxidation states. The red seaweed P. palmata revealed the highest removal efficiency for both Cr(III) and Cr(VI) at low initial concentrations. However, at high initial metal concentrations F. vesiculosus had the greatest removal efficiency for Cr(III) and performed almost identically to P. lanosa in terms of Cr(VI) removal. The Langmuir Isotherm mathematically described chromium binding to the seaweeds where F. vesiculosus had the largest q(max) for Cr(III) sorption (1.21mmol g(-1)) and P. lanosa had the largest Cr(VI) uptake (0.88mmol g(-1)). P. palmata had the highest affinity for both Cr(III) and Cr(VI) binding with b values of 4.94mM(-1) and 8.64mM(-1), respectively. Fourier transform infrared analysis revealed interactions of amino, carboxyl, sulphonate and hydroxyl groups in chromium binding to Ulva spp. The remaining seaweeds showed involvement of these groups to varying degrees as well as ether group participation in the brown seaweeds and for Cr(VI) binding to the red seaweeds.     

Mechanisms of chromium and arsenite adsorption by amino-functionalized SBA-15

The adsorption of Cr(VI) and As(III) by amino-functionalized SBA-15 (NH₂-SBA-15) from single and binary systems were investigated in this work. The effects of pH and temperature on the adsorption of NH₂-SBA-15 were studied. Adsorption kinetics, isotherm model, and thermodynamics were studied to analyze the experimental data. pH 2 was the optimum condition for the adsorption of Cr(VI) and pH 4 for As(III) adsorption. Increasing temperature had a positive effect on the removal of both Cr(VI) and As(III). The Freundlich isotherm model can depict the adsorption process best. The pseudo-second-order kinetic model fitted well with the kinetic data of Cr(VI) and As(III) in the single-component system. In the binary system, the adsorption of As(III) by NH₂-SBA-15 was slightly enhanced with the presence of Cr(VI); however, As(III) had no obvious effect on the removal of Cr(VI). Regeneration experiments indicated that 0.1 mol/L NaHCO₃ was an efficient desorbent for the recovery of Cr(VI) and As(III) from NH₂-SBA-15; the desorption rates for Cr(VI) and As(III) were 91.6 and 33.59 %, respectively. After five recycling cycles, the removal rates were 88 and 7 % for Cr(VI) and As(III) adsorption by NH₂-SBA-15, respectively.     

Chromium species behaviour in the activated sludge process

The purpose of this research was to compare trivalent chromium (Cr(III)) and hexavalent chromium (Cr(VI)) removal by activated sludge and to investigate whether Cr(VI) reduction and/or Cr(III) oxidation occurs in a wastewater treatment system. Chromium removal by sludge harvested from sequencing batch reactors, determined by a series of batch experiments, generally followed a Freundlich isotherm model. Almost 90% of Cr(III) was adsorbed on the suspended solids while the rest was precipitated at pH 7.0. On the contrary, removal of Cr(VI) was minor and did not exceed 15% in all experiments under the same conditions. Increase of sludge age reduces Cr(III) removal, possibly because of Cr(III) sorption on slime polymers. Moreover, the decrease of suspended solids concentration and the acclimatization of biomass to Cr(VI) reduced the removal efficiency of Cr(III). Batch experiments showed that Cr(III) cannot be oxidized to Cr(VI) by activated sludge. On the contrary, Cr(VI) reduction is possible and is affected mainly by the initial concentration of organic substrate, which acts as electron donor for Cr(VI) reduction. Initial organic substrate concentration equal to or higher than 1000 mgl(-1) chemical oxygen demand permitted the nearly complete reduction of 5 mgl(-1) Cr(VI) in a 24-h batch experiment. Moreover, higher Cr(VI) reduction rates were obtained with higher Cr(VI) initial concentrations, expressed in mg Cr(VI) g(-1) VSS, while decrease of suspended solids concentration enhanced the specific Cr(VI) reduction rate.     

Investigation of the removal mechanism of Cr(VI) in groundwater using activated carbon and cast iron combined system

Zero-valent iron (Fe⁰) has been widely used for Cr(VI) removal; however, the removal mechanisms of Cr(VI) from aqueous solution under complex hydrogeochemical conditions were poorly understood. In this research, the mixed materials containing cast iron and activated carbon were packed in columns for the treatment of aqueous Cr(VI)-Cr(III) in groundwater with high concentration of Ca²⁺, Mg²⁺, HCO₃ ⁻, NO₃ ⁻, and SO₄ ²⁻. We investigate the influences of those ions on Cr(VI) removal, especially emphasizing on the reaction mechanisms and associated precipitations which may lead to porosity loss by using X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM) techniques. The results show that the precipitations accumulated on the material surface were (Fe/Cr) (oxy)hydroxide, mixed Fe(III)-Cr(III) (oxy)hydroxides, Fe₂O₃, CaCO₃, and MgCO₃. During these reactions, the Cr(VI) was reduced to Cr(III) coupled with the oxidated Fe⁰ to Fe(II) through the galvanic corrosion formed by the Fe⁰-C and/or the direct electron transfer between Fe⁰ and Cr(VI). In addition, Cr(VI) could be reduced by aqueous Fe(II), which dominated the whole removal efficiency. The primary aqueous Cr(III) was completely removed together with Cr(III) reduced from Cr(VI) even when Cr(VI) was detected in the effluent, which meant that the aqueous Cr(III) could occupy the adsorption sites. In general, the combined system was useful for the Cr(VI)-Cr(III) treatment based on galvanic corrosion, and the hardness ions had a negative effect on Cr(VI) removal by forming the carbonates which might promote the passivation of materials and decrease the removal capacity of the system.

     

Spectroscopic investigation of magnetite surface for the reduction of hexavalent chromium

The reduction of Cr(VI) to Cr(III) by magnetite in the presence of added Fe(II) was characterized through batch kinetic experiments and the effect of Fe(II) addition and pH were investigated in this study. The addition of Fe(II) into magnetite suspension improved the reductive capacity of magnetite. Eighty percent of Cr(VI) was reduced by magnetite (6.5 g l(-1)) with Fe(II) (80 mg l(-1)) within 1 h, while 60% of Cr(VI) was removed by magnetite only. However, the extent of improved reductive capacity of magnetite with Fe(II) was less than that predicted by the summation of each reduction capacity of magnetite and Fe(II). The reduction of Cr(VI) in the magnetite suspension with Fe(II) increased with the increase of molar ratio of Fe(II) to Cr(VI) (0.6, 1, 1.5, 2.3) in the range of 0-2.3 and with the decrease of pH in the range of pH 8.0-5.5. The speciation of chromium, iron, and oxygen on the surface of magnetite was investigated by X-ray photoelectron spectroscopy. Cr 2p3/2, Fe 2p3/2, and O 1s peaks were mainly observed at 576.7 and 577.8 eV, at 711.2 eV, and at 530.2 and 531.4 eV, respectively. The results indicates that Cr(III) and Fe(III) were the dominant species on the surface of magnetite after reaction and that the dominant species covered the magnetite surface and formed metal (oxy)hydroxide.     

Hexavalent chromium removal by a novel Serratia proteamaculans isolated from the bank of Sebou River (Morocco)

The novel Serratia proteamaculans isolated from a chromium-contaminated site was tolerant to a concentration of 500 mg Cr(VI)/l. The optimum pH and temperature for reduction of Cr(VI) by S. proteamaculans were found to be 7.0 and 30 °C, respectively. The Cr(VI) reduction rate decreased with the increase in Cr(VI) concentration from 100 to 400 mg/l, suggesting the enzymatic chromium reduction. Resting and permeabilised cell assays provided the better evidence that chromate reduction in S. proteamaculans is enzymatic. Reduction by cell-free filtrate shows no extracellular chromate-reducing activity, revealing that this activity may be associated to membrane fraction and/or cytosolic fraction. Assays conducted with cytosolic and particulate fraction of S. proteamaculans confirmed the role of membrane-bound proteins in Cr(VI) reduction. Furthermore, chromium reduced by heat-treated cells suggests that membrane-associated chromate reductase activity of S. proteamaculans is preceded by its adsorption on the cell surface.     

Influences of redox transformation, metal complexation and aggregation of fulvic acid and humic acid on Cr(VI) and As(V) removal by zero-valent iron

This study investigated the removal kinetics and mechanisms of Cr(VI) and As(V) by Fe(0) in the presence of fulvic acid (FA) and humic acid (HA) by means of batch experiments. The focus was on the involvements of FA and HA in redox reactions, metal complexation, and iron corrosion product aggregation in the removal of Cr(VI) and As(V) removal by Fe(0). Synthetic groundwater was used as the background electrolyte to simulate typical groundwater. The results showed faster Cr(VI) removal in the presence of HA compared to FA. Fluorescence spectroscopy revealed that no redox reaction occurred in the FA and HA. The results of the speciation modeling indicate that the free Fe(II) concentration was higher in the presence of HA, resulting in a higher removal rate of Cr(VI). However, the removal of As(V) was inhibited in the HA solution. Speciation modeling showed that the concentration of dissolved metal-natural organic matter (metal-NOM) complexes significantly affected the aggregation of the iron corrosion products which in turn affected the removal of As(V). The aggregation was found to be induced by gel-bridging of metal-NOM with the iron corrosion products. The effects of metal-NOM on the aggregation of the iron corrosion products were further confirmed by TEM studies. Larger sizes of iron corrosion products were formed in the FA solution compared to HA solution. This study can shed light on understanding the relationships between the properties of NOM (especially the content of metal-binding sites) and the removal of Cr(VI) and As(V) by Fe(0).     

Kinetics of the reduction of hexavalent chromium with the brown seaweed Ecklonia biomass

The dead biomass of the brown seaweed, Ecklonia sp., is capable of reducing toxic Cr(VI) into less toxic or nontoxic Cr(III). However, little is known about the mechanism of Cr(VI) reduction by the biomass. The objective of this work was to develop a kinetic model for Cr(VI) biosorption, for supporting our mechanism. The reduction rate of Cr(VI) increased with increasing total chromate concentration, [Cr(VI)], and equivalent concentration of organic compounds, [OCs], and decreasing solution pH. It was found that the reduction rate of Cr(VI) was proportional to [Cr(VI)] and [OCs], suggesting the simple kinetic equation -d[Cr(VI)]/dt=k[Cr(VI)][OCs]. When considering the consumption of organic compounds due to the oxidation by Cr(VI), an average rate coefficient of 9.33 (+/-0.65)microM(-1)h(-1) was determined, at pH 2. Although the function of the pH could not be expressed in a mechanistic manner, an empirical model able to describe the pH dependence was obtained. It is expected that the developed rate equation could likely be used for design and performance predictions of biosorption processes for treating chromate wastewaters.     

As(V) adsorption on amorphous iron oxide: Triple layer modelling

The adsorption of As(V) by amorphous iron oxide was investigated at 25°C, 0.01 M NaNO₃ background electrolyte as a function of solution pH(4–10) at three initial As(V) concentrations and two Fe(III) concentrations. As(V) adsorption increased with decreasing pH. A modified Langmuir isotherm has been used for describing an equilibrium partition existing between solid and liquid phases. The triple-layer model was used for simulating As(V) adsorption on iron oxide surface. This model was able to describe As(V) adsorption over the pH range 4–10, all at the concentrations of As(V) and Fe(III) studied. =Fe(H₂AsO₄)⁰, = Fe(HAsO₄)⁻ and = Fe(AsO₄)²⁻ have been shown through simulation with inner-sphere complexation products to be more consistent with experimental adsorption observations than complexation with other surface species.     

Removal of Cr(VI) and humic acid by using TiO2 photocatalysis

The removal efficiencies of Cr(VI) and HA, using a TiO(2)-mediated photocatalytic process, were investigated with variations in the pH, TiO(2) dosage and Cr(VI)/HA ratio. During the photocatalytic reaction, the total removal of Cr(VI) occurred through adsorption onto TiO(2), as well as its reduction to Cr(III). However, oxidation and adsorption were identified as important removal processes for the treatment of HA. Due to the anionic type adsorption onto TiO(2) and its acid-catalyzed photocatalytic reduction, the removal of Cr(VI) decreased with increasing pH, while that of HA increased with increasing pH. The TiO(2) dosage was also an important parameter for the removal of Cr(VI). As the TiO(2) dosage was increased to 2.5 g l(-1), the removal of Cr(VI) was continuously enhanced, but decreased at dosages above 3 g l(-1) due to the increased blockage of the incident UV light used for the photocatalytic reaction. The removal of Cr(VI) was greatly enhanced when the system contained both HA and Cr(VI) compared to Cr(VI) alone. Also, the removal of HA was greatly enhanced when the system contained both HA and Cr(VI) compared to HA alone. The removal of Cr(VI) was continuously enhanced as the HA concentration gradually increased; however, no further increase was observed above 20 mg l(-1) HA due to the increased absorption of the UV light. This result supports that the photocatalytic reaction, with illuminated TiO(2), could be applied to more effectively treat wastewater containing both Cr(VI) and HA than that containing a single species only.     

Cr(VI) sorption by free and immobilised chromate-reducing bacterial cells in PVA–alginate matrix: equilibrium isotherms and kinetic studies

Chromate-resistant bacterial strain isolated from the soil of tannery was studied for Cr(VI) bioaccumulation in free and immobilised cells to evaluate its applicability in chromium removal from aqueous solution. Based on the comparative analysis of the 16S rRNA gene, and phenotypic and biochemical characterization, this strain was identified as Paenibacillus xylanilyticus MR12. Mechanism of Cr adsorption was also ascertained by chemical modifications of the bacterial biomass followed by Fourier transform infrared spectroscopy analysis of the cell wall constituents. The equilibrium biosorption analysed using isotherms (Langmuir, Freundlich and Dubinin–Redushkevich) and kinetics models (pseudo-first-order, second-order and Weber–Morris) revealed that the Langmuir model best correlated to experimental data, and Weber–Morris equation well described Cr(VI) biosorption kinetics. Polyvinyl alcohol alginate immobilised cells had the highest Cr(VI) removal efficiency than that of free cells and could also be reused four times for Cr(VI) removal. Complete reduction of chromate in simulated effluent containing Cu²⁺, Mg²⁺, Mn²⁺ and Zn²⁺ by immobilised cells, demonstrated potential applications of a novel immobilised bacterial strain MR12, as a vital bioresource in Cr(VI) bioremediation technology.     

Reliable evidences that the removal mechanism of hexavalent chromium by natural biomaterials is adsorption-coupled reduction

For the last few decades, over 200 papers have been published in the Cr(VI) biosorption research field. Most early studies have claimed that Cr(VI) was removed from aqueous phase through an anionic adsorption, but this approach has been lost old original position. It has been newly explained that these findings were misinterpreted due to errors in measuring the concentrations of different chromium species in the aqueous phase, insufficient contact time required for equilibrium and the lack of information about the oxidation state of the chromium bound to biomaterials. Although 'adsorption-coupled reduction' is now widely accepted as the mechanism of Cr(VI) biosorption by natural biomaterials, a number of researchers still believe that Cr(VI) is removed by anionic adsorption onto the biomaterials. Therefore, the objective of this study was to show reliable evidences that the removal mechanism of Cr(VI) by natural biomaterials is 'adsorption-coupled reduction'. Sixteen natural biomaterials were used to study the Cr(VI) biosorption. Not only Cr(VI) but also total Cr in the aqueous phase were analyzed. X-ray photoelectron spectroscope was also used to verify the oxidation state of the chromium bound to the biomaterials. Finally, the removal behavior of Cr(VI) by each biomaterial was described by a kinetic model based on a redox reaction.     

Modelling the sorption of metals from aqueous solutions on goethite fixed-beds

The research on separation methods of toxic metals from wastewater streams is continuous and intensive and, among them, sorption processes are considered of particular importance, mainly due to their effectiveness. The sorption of chromate anions and zinc cations from dilute aqueous solutions using a packed-bed (column configuration) of synthesised granulated goethite was investigated in the present study. The examined parameters during this investigation were the following: (1) the initial pH value of metal-laden aqueous solution (two representative values at acidic pH, 3.5 and 5.0, were tested); (2) the quantity of sorbent in the column, corresponding to bed height; and (3) the influence of ethylene diamine tetra acetic acid (EDTA) addition, a common, strong chelating agent. The Bed Depth-Service Time model has been applied to the sorption results in order to model the column operation. The removal efficiency of Cr(VI) anions by the sorptive column was found to be higher than that of Zn(II) cations. The presence of EDTA caused a certain decrease of removal efficiency for the case of hexavalent chromium, due to competition for the same sorption sites, while the removal of divalent zinc was increased, due to variation of cation speciation.