TiO2光催化降解有机颜料艳红RGS母液研究

以TiO2为催化剂,对有机颜料艳红RGS母液进行了一系列光催化降解试验.考察了催化剂用量、溶液pH值、初始浓度、不同光源和照射时间对脱色率的影响.结果表明,溶液相对初始浓度为0.2、pH<8、催化剂用量为1g/L时,以紫外灯(254nm)为光源,反应120 min,脱色率可达93%以上.     

高效海洋溢油降解菌降解海洋溢油条件的优化研究

针对海洋溢油污染问题,采用实验室筛选的海洋溢油降解菌HJ01和HJ02开展海洋溢油微生物降解优化研究,采用单因素实验和多因素正交实验进行降解率测定。结果表明,单因素实验条件下,当pH值为7、培养温度35℃、石油初始浓度7 500mg/L、NaCl含量20 000mg/L时,HJ01和HJ02对海洋溢油的降解效果最佳。正交实验条件下,HJ01在pH值为7、培养温度35℃、石油初始浓度7 500mg/L、NaCl含量10 000mg/L时降解效果最佳;HJ02在pH值为7、培养温度30℃、石油初始浓度11 000 mg/L、NaCl含量10 000mg/L时降解效果最佳。     

阳离子艳红染料的光催化降解

本文研究了以沉淀法制备的TiO2为催化剂，紫外杀菌灯为光源，对阳离子艳红染料进行光催化降解的可行性，结果表明，在实验条件下，本系统对阳离子艳红染料有明显的降解效果，浓度为10mg/L的阳离子艳红染料经过30min的处理，其降解率＞88％，此外，还探讨了溶液初始pH值，催化剂的投加量，光照距离和液层高度等因素对光降解反应的影响。     

纸载P-TiO_2光催化降解甲醛的影响因素研究

本文以牛皮纸作载体,用浸渍法制备了具有光催化作用的纳米P-TiO2光催化剂,对室内一定浓度的甲醛气体进行了降解实验研究。通过实验探讨了甲醛的初始浓度、催化剂的用量、湿度条件、溶胶pH值和金属离子的掺杂5个影响甲醛降解率的因素,结果采用美国interscan公司生产的4160型甲醛分析仪进行表征。实验结果表明,当甲醛的初始浓度约为1.53mg/m3,P-TiO2用量为11.94g,湿度约为52%,溶胶pH=5.01,掺杂6.00mL 0.20 mol/L Cu2＋离子时,甲醛的降解效果最好,最高可达93.50%,甲醛浓度降至0.0994mg/m3,达到了GB/T 18883—2002标准中规定的0.10 mg/m3。     

介孔氧化铁催化降解诺氟沙星实验条件的优化研究

选取诺氟沙星为目标污染物,以介孔氧化铁为催化剂,催化过氧化氢降解水中微量有机污染物,设计正交实验并利用SPSS软件进行数据分析,分别讨论了pH、H_2O_2初始浓度、诺氟沙星初始浓度以及催化剂投加量对降解率的影响,并得到选定因素水平范围内的最优化反应条件:初始p H为7,初始H_2O_2浓度100 m M,初始诺氟沙星浓度2 mg/L,催化剂投加量0.7 g/L。最优化反应条件下,120 min诺氟沙星的降解率达到99%。通过SPPS方差分析可得,各因素影响大小的排序为诺氟沙星初始浓度催化剂投加量初始pH初始H_2O_2浓度。     

HPA／ZnFe2O4-TiO2光催化剂的制备及对马拉硫磷的可见光降解

以纳米TiO2载体,利用浸渍法制备了HPA／ZnFe2O4-TiO2光催化剂。对制备的催化剂进行了XRD、BET、TEM和UV-vis DRS表征。结果表明,催化剂样品均为锐钛矿相且ZnFe2O4很好地分散在载体表面,HPA／ZnFe2O4-TiO2光催化荆的平均粒径为10nm且在380-670nm均有强的光响应;反应最佳的HPA浓度为O.08molfL,最佳的ZnFe2O4负载量为1％。考察了HPA溶液初始浓度、ZnFe2O4负载量、溶液初始pH值、H2O2用量、催化剂用量对催化剂活性的影响。在溶液初始pH=13,H2O2=6mmol／L,催化剂用量为2g/L的最优条件下,光照反应进行100min后,马拉硫磷的降解率可达87％;重复4次后马拉硫磷的降解率仍可以达到67％。     

纳米二氧化钛光催化氧化降解苯酚废水实验

开展实验室模拟苯酚废水的二氧化钛光催化氧化实验。结果表明：在苯酚废水曝气量为0～3L/min的条件下,随着曝气量的增大,COD去除率先增大后减小;初始浓度不变,光照时间为1h的条件下, 调节pH值在3～11,苯酚废水COD去除率随着pH值的增大而减小,当pH值为11时, COD去除率又开始增 大,酸性条件比碱性条件下COD去除率高;随着二氧化钛投加量的增加,COD去除率增大,当二氧化钛投加量 为10g/L时,COD去除率反而降低,二氧化钛最佳投加量为3g/L;随着苯酚废水初始浓度由75mg/L增加至300mg/L,COD去除率由78.2％降低到58.1％;反应温度的改变对COD和TOC的去除率没有影响。     

Fenton试剂高级氧化法降解甲基橙模拟废水研究

甲基橙是一种较难降解的有机苯环偶氮染料之一,研究其降解性能对其他染料废水体系的降解研究具有普遍参考价值。通过研究Fenton试剂降解甲基橙过程中的H202浓度、Fe2＋浓度、反应时间和反应体系pH值对甲基橙降解的影响,确定其最佳降解工艺条件为：当甲基橙浓度为20mg／L、pH值为3、Fe2＋浓度为1．5mmol／L、H2O2为32mmol/L时,降解率达到最大值（98．95％）。     

La掺杂TiO2/有机改性膨润土对TNT弹药废水的光催化降解性能研究

利用超声强化溶胶-凝胶法制备了La掺杂TiO2/有机改性膨润土复合光催化材料并进行了结构表征;以弹药废水中主要污染物质TNT作为目标物,考察了影响光催化降解性能的因素.结果表明：有机改性后复合材料的吸附性能和光催化性能均有所增加,对TNT的60min的吸附去除率和光催化降解率分别达到9.68％和94.53％;影响TNT光催化降解率的因素有光照时间、催化剂用量、TNT初始浓度、溶液pH值和光照强度.     

活性炭/氧化亚铜对聚乙烯醇废水的光催化效果研究

以活性炭为载体,采用液相还原法制备活性炭/氧化亚铜(AC/Cu_2O)光催化剂,利用傅立叶变换红外光谱仪(IR)、扫描电子显微镜(SEM)、X射线衍射仪(XRD)等对样品进行官能团分析、形貌观察和物相分析。利用该催化剂处理聚乙烯醇(PVA)废水,实验结果表明:在水样初始pH为5、PVA初始浓度75 mg/L、催化剂投加量4 g/L、反应时间50 min时PVA的去除率为90.60%;且水样初始pH对PVA的去除效果影响最显著。     

Arsenic and chromium removal by mixed magnetite–maghemite nanoparticles and the effect of phosphate on removal

Adsorption of arsenic and chromium by mixed magnetite and maghemite nanoparticles from aqueous solution is a promising technology. In the present batch experimental study, a commercially grade nano-size ‘magnetite’, later identified in laboratory characterization to be mixed magnetite–maghemite nanoparticles, was used in the uptake of arsenic and chromium from different water samples. The intent was to identify or develop a practical method for future groundwater remediation. The results of the study showed 96–99% arsenic and chromium uptake under controlled pH conditions. The maximum arsenic adsorption occurred at pH 2 with values of 3.69 mg/g for arsenic(III) and 3.71 mg/g for arsenic(V) when the initial concentration was kept at 1.5 mg/L for both arsenic species, while chromium(VI) concentration was 2.4 mg/g at pH 2 with an initial chromium(VI) concentration of 1 mg/L. Thus magnetite–maghemite nanoparticles can readily adsorb arsenic and chromium in an acidic pH range. Redox potential and pH data helped to infer possible dominating species and oxidation states of arsenic and chromium in solution. The results also showed the limitation of arsenic and chromium uptake by the nano-size magnetite–maghemite mixture in the presence of a competing anion such as phosphate. At a fixed adsorbent concentration of 0.4 g/L, arsenic and chromium uptake decreased with increasing phosphate concentration. Nano-size magnetite–maghemite mixed particles adsorbed less than 50% arsenic from synthetic water containing more than 3 mg/L phosphate and 1.2 mg/L of initial arsenic concentration, and less than 50% chromium from synthetic water containing more than 5 mg/L phosphate and 1.0 mg/L of chromium(VI). In natural groundwater containing more than 5 mg/L phosphate and 1.13 mg/L of arsenic, less than 60% arsenic uptake was achieved. In this case, it is anticipated that an optimum design with magnetite–maghemite nanoparticles may achieve high arsenic uptake in field applications.     

Adsorption characteristics of Cu and Ni on Irish peat moss

Peat has been widely used as a low cost adsorbent to remove a variety of materials including organic compounds and heavy metals from water. Various functional groups in lignin allow such compounds to bind on active sites of peat. The adsorption of Cu(2+) and Ni(2+) from aqueous solutions on Irish peat moss was studied both as a pure ion and from their binary mixtures under both equilibrium and dynamic conditions in the concentration range of 5-100mg/L. The pH of the solutions containing either Cu(2+) or Ni(2+) was varied over a range of 2-8. The adsorption of Cu(2+) and Ni(+2) on peat was found to be pH dependent. The adsorption data could be fitted to a two-site Langmuir adsorption isotherm and the maximum adsorption capacity of peat was determined to be 17.6 mg/g for Cu(2+) and 14.5mg/g for Ni(2+) at 298 K when the initial concentration for both Cu(2+) and Ni(2+) was 100mg/L, and the pH of the solution was 4.0 and 4.5, respectively. Column studies were conducted to generate breakthrough data for both pure component and binary mixtures of copper and nickel. Desorption experiments showed that 2mM EDTA solution could be used to remove all of the adsorbed copper and nickel from the bed.     

Degradation of a commercial textile biocide with advanced oxidation processes and ozone

The occurrence of significant amounts of biocidal finishing agents in the environment as a consequence of intensive textile finishing activities has become a subject of major public health concern and scientific interest only recently. In the present study, the treatment efficiency of selected, well-known advanced oxidation processes (Fenton, Photo-Fenton, TiO(2)/UV-A, TiO(2)/UV-A/H(2)O(2)) and ozone was compared for the degradation and detoxification of a commercial textile biocide formulation containing a 2,4,4'-trichloro-2'-hydroxydiphenyl ether as the active ingredient. The aqueous biocide solution was prepared to mimic typical effluent originating from the antimicrobial finishing operation (BOD(5,o) < or =5 mg/L; COD(o)=200 mg/L; DOC(o) (dissolved organic carbon)=58 mg/L; AOX(o) (adsorbable organic halogens)=48 mg/L; LC(50,o) (lethal concentration causing 50% death or immobilization in Daphnia magna)=8% v/v). Ozonation experiments were conducted at different ozone doses (500-900 mg/h) and initial pH (7-12) to assess the effect of ozonation on degradation (COD, DOC removal), dearomatization (UV(280) and UV(254) abatement), dechlorination (AOX removal) and detoxification (changes in LC(50)). For the Fenton experiments, the effect of varying ferrous iron catalyst concentrations and UV-A light irradiation (the Photo-Fenton process) was examined. In the heterogenous photocatalytic experiments, Degussa P25-type TiO(2) was used as the catalyst and the effect of reaction pH (3, 7 and 12) and H(2)O(2) addition on the photocatalytic treatment efficiency was examined. Although in the photochemical (i.e. Photo-Fenton, TiO(2)/UV-A and TiO(2)/UV-A/H(2)O(2)) experiments appreciably higher COD and DOC removal efficiencies were obtained, ozonation appeared to be equally effective to achieve dearomatization (UV(280) abatement) at all studied reaction pH. During ozonation of the textile biocide effluent, AOX abatement proceeded significantly faster than dearomatization and was complete after 20 min ozonation (267 mg O(3)). On the other hand, for complete detoxification, ozonation had to be continued for at least 30 min (corresponding to 400mg O(3)). Effective AOX and acute toxicity removal was also obtained after heterogeneous photocatalytic treatment (TiO(2)/UV-A and TiO(2)/UV-A/H(2)O(2)). The Fenton-based treatment experiments and particularly the dark Fenton reaction resulted in relatively poor degradation, dearomatization, AOX and acute toxicity removals.     

纳米零价铁去除磷酸盐机理研究

纳米零价铁(nanoscale zero-valent iron,nZVI)颗粒具有独特核-壳结构,使其具有较强氧化还原特性,比表面积大和表面活性高等特点,因此被广泛用于不同环境介质中多种污染物的去除修复。本研究采用传统的液相化学还原法合成nZVI颗粒并用于去除水溶液中的磷酸盐。通过扫描电子显微镜(SEM)、透射电子显微镜(TEM)和X射线衍射仪(XRD)表征nZVI颗粒的性质。实验研究了nZVI投加量、PO3-4初始浓度、溶液初始pH值对nZVI去除PO3-4效率的影响及微米零价铁(micro-ZVI)和nZVI去除PO3-4的对比。实验结果表明,当PO3-4初始浓度为20mg/L时,随着nZVI投加量从200mg/L增加到1000mg/L,PO3-4去除效率从32.94%上升到90.17%;当nZVI投加量为600mg/L时,随着PO3-4初始浓度从10mg/L增加到100mg/L,PO3-4去除效率从87.33%下降到45.77%;当nZVI投加量为600mg/L且PO3-4初始浓度为20mg/L,溶液pH分别为3和4时,PO3-4去除效率分别为83.63%和92.36%;nZVI和mZVI投加量均为600mg/L且PO3-4初始浓度为10mg/L,nZVI的PO3-4去除率(87.33%)是mZVI(8.86%)的9.86倍。研究结果表明,nZVI能够高效去除水体中的磷酸盐,主要去除机理是吸附和化学沉淀的双重作用。     

Thermochemical esterifying citric acid onto lignocellulose for enhancing methylene blue sorption capacity of rice straw

In this paper, rice straw was esterified thermochemically with citric acid (CA) to produce potentially biodegradable cationic sorbent. The modified rice straw (MRS) and crude rice straw (CRS) were evaluated for their methylene blue (MB) removal capacity from aqueous solution. The effects of various experimental parameters (e.g., initial pH, sorbent dose, dye concentration, ion strength, and contact time) were examined. The ratio of MB sorbed on CRS increased as the initial pH was increased from pH 2 to 10. For MRS, the MB removal ratio came up to the maximum value beyond pH 3. The 1.5g/l or up of MRS could almost completely remove the dye from 250mg/l of MB solution. The ratio of MB sorbed kept above 98% over a range from 50 to 450mg/l of MB concentration when 2.0g/l of MRS was used. Increase in ion strength of solution induced decline of MB sorption. The isothermal data fitted the Langmuir model. The sorption processes followed the pseudo-first-order rate kinetics. The intraparticle diffusion rate constant (k(id)) was greatly increased due to modification.     

影响高浓度NH3-N废水吹脱-硝化过程的实验研究

废水中含氨氮过多，对人和动物的健康产生极大威胁，此外，水体中NH3-N浓度过高，也增加了废水生化的处理难度，为此，废水脱氮成为水处理领域的热点和难点。文章采取先用空气将高浓度NH3-N废水的中的一部分NH3-N吹脱，然后在适宜的氨氮剩余浓度下，采用活性污泥法对剩余NH3-N进行硝化处理。用空气吹脱NH3-N，碱度直接影响吹脱效果和最终的剩余氨氮浓度。在硝化反应时，pH值、温度、溶解氧对硝化反应影响十分大。文章通过大量实验，获得了NH3-N废水起始浓度为1000mg／L左右时的最佳吹脱碱度，获得了适宜的氨氮剩余浓度。同时得出了pH值、温度、溶解氧对硝化反应的影响规律。这些数据和规律对生产有一定的指导意义。     

Response surface optimization of acid red 119 dye from simulated wastewater using Al based waterworks sludge and polyaluminium chloride as coagulant

In this research, the performance of Polyaluminium Chloride (PAC) and Polyaluminium Chloride sludge (PACS) as coagulants for acid red 119 (AR119) dye removal from aqueous solutions were compared. The sample of PACS was collected from "Baba Sheikh Ali" water treatment plant (Isfahan, Iran) where PAC is used as a coagulant in the coagulation/flocculation process. A response surface methodology was applied to evaluate the simple and combined effects of the operating variables including initial pH, coagulant dosage and initial dye concentration and to optimize the operating conditions of the treatment process. Results reveal that the optimal conditions for dye removal were initial pH 3.42, coagulant dosage of 4.55 g dried PACS/L and initial dye concentration of 140 mg/L for PACS, while the optimal initial pH, coagulant dosage and initial dye concentration for PAC were 3.8, 57 mg/L and 140 mg/L, respectively. Under these optimal values of process parameters, the dye removal efficiency of 94.1% and 95.25% was observed for PACS and PAC, respectively. Although lower amount of PAC in comparison with PACS was needed for specific dye removal, the reuse of PACS as a low-cost material can offer some advantages such as high efficiency for AR119 dye removal and economic savings on overall water and wastewater treatment plant operation costs.     

Fluoride removal by a continuous flow electrocoagulation reactor

Long-term consumption of water containing excessive fluoride can lead to fluorosis of the teeth and bones. Electrocoagulation (EC) is an electrochemical technique, in which a variety of unwanted dissolved particles and suspended matter can be effectively removed from an aqueous solution by electrolysis. Continuous flow experiments with monopolar aluminium electrodes for fluoride removal were undertaken to investigate the effects of the different parameters such as: current density (12.5-50A/m(2)), flow rate (150-400 mL/min), initial pH (4-8), and initial fluoride concentration (5-25mg/L). The highest treatment efficiency was obtained for the largest current and the removal efficiency was found to be dependent on the current density, the flow rate and the initial fluoride concentration when the final pH ranged between 6 and 8. The composition of the sludge produced was analysed using the X-ray diffraction (XRD) spectrum. The strong presence of the aluminium hydroxide [Al(OH)(3)] in the above pH range, which maximizes the formation of aluminium fluoride hydroxide complex [Al(n)F(m)(OH)(3n-m)], is the main reason for defluoridation by electrocoagulation. The results obtained showed that the continuous flow electrocoagulation technology is an effective process for defluoridation of potable water supplies and could also be utilized for the defluoridation of industrial wastewater.     

Phenol degradation using combined effects of hydrodynamic cavitation and oxidant: Doehlert matrix

Hydrodynamic cavitation (HC)-based treatments have been proposed for the degradation of phenol as a toxic pollutant. The present work aimed to optimize the degradation of phenol using HC by means of Doehlert experimental design, which has not been previously addressed. Initially, operational parameters of hydraulic characteristics of the pump, inlet pressure, solution pH, and initial concentration were optimized; later, the effects of pH solution and H₂O₂ loading or initial pollutant concentration on phenol degradation were explored using the Doehlert experimental design. It was observed that phenol degradation is strongly dependent on the pH of the solution. Also, the acidic condition favors the formation of hydroxyl radicals and thus, the degradation of phenol. Based on the Doehlert matrix, the 94.1% phenol degradation and 68.60% total organic carbon (TOC) were obtained in 180 min at 304.5 mg/L of hydrogen peroxide at an initial concentration of 20 mg/L, 2.0 pH, and 90 psi inlet pressure, providing a cavitational yield of 6.33 × 10⁻⁶ mg/J and minimum treatment cost of US$/L 0.13. Overall, it has been observed that HC can be a promising route for the removal of pollutants (phenol) effectively using hydrogen peroxide as an additive.