Recycling of steel slag and glass cullet from energy saving lamps by fast firing production of ceramics

The paper reports on some experimental results obtained from the production of ceramics containing steel slag and glass cullet from exhaust energy saving lamps mixed in different proportions. Blending of components was done by attrition milling. Pressed powders were fast fired (50 min, cold to cold) in air up to several temperatures in the range 1000–1140 °C. The sintering behaviour was studied by shrinkage and water absorption measurements. Density, strength and hardness of the fired bodies were determined and XRD were examined. The fired samples were finally tested in acidic environment in order to evaluate their elution behaviour and consequently their possible environmental compatibility. It is observed that the composition containing 60 wt.% of steel slag and 40 wt.% of glass cullet displayed the best overall behaviour.     

Effects of Waste Paper Sludge on the Physico-Mechanical Properties of High Density Polyethylene/Wood Flour Composites

The objective of this work was to determine some physical and mechanical properties of the high density polyethylene (HDPE) composites reinforced with various mixtures of the paper sludge and the wood flour, and to evaluate the coupling agent performance. The waste sludge materials originating from two different sources including paper making waste water treatment sludge (PS) and ink-eliminated sludge (IES) were characterized in terms of physico-chemical properties. In the experiment, four levels of paper sludge (20, 30, 40 and 60 wt%), three levels of wood flour (20, 40 and 60 wt%), and two levels of coupling agent (MAPE) content (2 and 3 wt%) were used. The flexural properties of the composites were positively affected by the addition of the sludge. Especially, tensile modulus improved with the increase of paper sludge content. With the addition of MAPE, flexural properties improved considerably compared with control specimens (without any coupling agent). The results showed that the water absorption (WA) and thickness swelling (TS) values of the samples decreased considerably with increasing sludge content in the composite, while they increased with increasing wood flour content. It is to be noted that with incorporation of MAPE in the composite formulation, the compatibility between the wood flour and HDPE was enhanced through esterification, which reduced the WA and TS and improved the mechanical properties. Composites made with IES exhibited superior physico-mechanical properties compared with the PS filled composites. Overall results suggest that the waste paper sludge materials were capable of serving as feasible reinforcing fillers for thermoplastic polymer composites.     

Recycling PC and TV waste glass in clay bricks and roof tiles

Disposal of PC monitors and TV sets is a growing problem, with over 40% of the weight of these systems comprised of waste glasses with high Pb (funnel) or Ba–Sr concentrations (panel), making them unsuitable for recycling and manufacturing new glass. A possible way to re-use these glasses is in the manufacturing of clay bricks and roof tiles. This possibility was appraised by laboratory simulation of the brickmaking process and technological characterization of unfired and fired products. The recycling of both funnel and panel glasses into clay bodies is technologically feasible, resulting in a substantially reduced plasticity behaviour during shaping–drying (implying a reduction of mechanical strength), and a promotion of sintering during firing. No significant release of Pb, Ba, and Sr was observed during the firing and leaching test for the carbonate-poor body; in contrast, some Pb volatilization during firing and Sr leaching were observed for the carbonate-rich body. Additions of 2 wt.% appear to be practicable, while 5 wt.% glass induces unacceptable modifications of technological properties. The recommended amount is within 2 and 4 wt.%, depending on the characteristics of the clay bodies. The main constraint is that the glass must have a particle size below the limit of the pan mills used in brickmaking (<1 mm).     

The applicability of different waste materials for the production of lightweight aggregates

The applicability of different waste materials for the production of lightweight aggregates has been studied. The following waste materials were investigated: silica sludge, superfluous clay in the quarry, waste glass, and residue from the polishing process of different types of stone. SiC and MnO₂ were selected as foaming agents. Feldspar containing minerals and scrap glass were added in order to lower the softening point of the waste materials. The granules were prepared by mixing together finely ground waste with one or both of the selected foaming agents. The granules were then fired at different temperatures above the softening point of the glassy phase within the temperature range from 1150 to 1220 °C, where the foaming agent degasses, and the resulting gasses remain trapped in the glassy structure. The foaming process was observed by hot-stage microscopy. The properties of the so-obtained granules, such as their apparent density and compressive strength, were determined, and their microstructures were evaluating using SEM and polarizing microscopy.With the addition to clay of polishing residue from granite-like rocks, after firing at 1220 °C homogeneously porous granules with a density down to 0.42 g/cm³ were obtained, whereas with the addition to waste silica sludge of polishing residue from granite-like rocks and waste glass with a foaming agent, after firing at 1220 °C densities from 0.57 to 0.82 g/cm³ were obtained.     

Cement‐based solidification/stabilization of phenol‐contaminated soil by bentonite and organophilic clay

The performance of ordinary and organophilic clays in the solidification and stabilization process was investigated with respect to the unconfined compressive strength (UCS) and leaching of phenol‐contaminated soil. The samples contained 2,000 mg/kg of phenol. White cement (15 and 30 percent by weight [wt%]) was used as binder, while ordinary and organophilic clays (8, 15, and 30 wt%) were applied as additives for reducing the harmful effects of phenol interference in cement hydration with a 28‐day curing time. The results revealed that the UCS is reduced by increasing the amount of clays. The values of UCS of all samples met the minimum standards specified for disposal in sanitary landfills determined by developed countries. The leaching test demonstrated that the degree of leaching diminished with increased clay content in all samples of both clay types. This reduction was observed to be greater in samples containing organophilic clay than in bentonite clay samples. Furthermore, the best composition of the materials tested was determined to be 30 wt% white cement plus 13.3 wt% organophilic clay with a compressive strength of 3,839 kPa, phenol removal percentage of 80 percent, and a cost of $67 per ton of contaminated soil.     

Effects of recycled glass substitution on the physical and mechanical properties of clay bricks

In this study, wasted glasses from structural glass walls up to 45 wt.% were added into clay mixtures in brick manufacturing process. Physical and mechanical properties of clay bricks were investigated as functions of the wasted glass content and the firing temperature. The results indicated that with proper amount of wasted glasses and firing temperature, clay bricks with suitable physical and mechanical properties could be obtained. The compressive strength as high as 26–41 MPa and water absorption as low as 2–3% were achieved for bricks containing 15–30 wt.% of glass content and fired at 1100 °C. When the glass waste content was 45 wt.%, apparent porosity and water absorption was rapidly increased.     

Lightweight aggregate made from sewage sludge and incinerated ash

In this study, sewage sludge ash (SSA), with similar characteristics to expansive clay, was used as the principal material and sewage sludge (SS) as the admixture to sinter lightweight aggregate and to study the influences of raw material composition on pelletising, sintering effect and aggregate properties. Results showed that both SS and SSA could be sintered to produce synthetic aggregates individually or mixed. Increasing the amount of SS would decrease the pelletising ratio. Under the consideration of energy saving, the mixture of SSA was better for sintering normal weight aggregate. On the contrary, the mixture that added 20-30% of SS was more adequate to make lightweight aggregates. Adding SS would enhance the oxidation-reduction reaction and lower the bulk density and sintering temperature of aggregates to save energy. Sintering temperature affected the properties of sewage sludge ash lightweight aggregate (SSALA) more than retention period did. Prolonging the retention period could improve bloating effect.     

Laboratory stabilization/solidification of surrogate and actual mixed-waste sludge in glass and grout

Grout and glass formulations were developed for the stabilization of highly radioactive tank sludges. These formulations were tested in the laboratory with a surrogate and with a sample of an actual mixed waste tank sludge. The grout formulation was tested at wet-sludge loadings of 50–60 wt%, giving a volume increase of about 40–50 vol%. Dried sludge was vitrified into glass at waste oxide loadings of 40–50 wt%, giving a volume decrease of about 50–60 vol%. The Resource Conservation and Recovery Act (RCRA) metals included in surrogate testing were Ag, Ba, Cd, Cr, Ni, Pb, Se, Tl and Hg. Since vitrification would volatilize, not stabilize mercury, it was not included in the surrogates vitrified. The actual sludge sample was only characteristically hazardous for mercury by the toxic characteristic leaching procedure (TCLP) but exceeded the Universal Treatment Standard (UTS) limit for chromium. The grout and glass formulations stabilized these RCRA metals within UTS limits. In addition, a grout leachability index of about 9–10 was measured for both ⁸⁵Sr and ¹³⁷Cs, meeting the recommended requirement of >6. The glass leachability index was estimated to be >18 for cold cesium and strontium.     

Effects of using arsenic–iron sludge wastes in brick making

The arsenic–iron sludge generated in most of the treatment systems around the world is discharged into the nearest watercourse, which leads to accumulative rise of arsenic and iron concentrations in water. In this study, attempts were made to use the arsenic–iron sludge in making bricks and to analyze the corresponding effects on brick properties. The water treatment plant sludge is extremely close to brick clay in chemical composition. So, the sludge could be a potential substitute for brick clay. This study involved the addition of sludge with ratios 3%, 6%, 9% and 12% of the total weight of sludge–clay mixture. The physical and chemical properties of the produced bricks were then determined and evaluated and compared to control brick made entirely from clay. Results of different tests indicated that the sludge proportion and firing temperature were the two key factors in determining the quality of bricks. The compressive strength of 3%, 6%, 9% and 12% sludge containing brick samples were found to be 14.1 MPa, 15.1 MPa, 9.4 MPa and 7.1 MPa, respectively. These results indicate that the compressive strength of prepared bricks initially increased and then decreased with the increase of sludge proportion. Leaching characteristics of burnt bricks were determined with the variation of pH at a constant temperature. The optimum amount of sludge that could be mixed with clay to produce good bonding of clay–sludge bricks was found to be 6% (safely maximum) by weight.     

Fly ash of mineral coal as ceramic tiles raw material

The aim of this work was to evaluate the use of mineral coal fly ash as a raw material in the production of ceramic tiles. The samples of fly ash came from Capivari de Baixo, a city situated in the Brazilian Federal State of Santa Catarina. The fly ash and the raw materials were characterized regarding their physical chemical properties, and, based on these results; batches containing fly ash and typical raw materials for ceramic tiles were prepared. The fly ash content in the batches varied between 20 and 80 wt%. Specimens were molded using a uniaxial hydraulic press and were fired. All batches containing ash up to 60 wt% present adequate properties to be classified as several kinds of products in the ISO 13006 standard () regarding its different absorption groups (pressed). The results obtained indicate that fly ash, when mixed with traditional raw materials, has the necessary requirements to be used as a raw material for production of ceramic tiles.     

The effect of the addition of fly ash to municipal digested sludge on its electroosmotic dewatering

Effective handling of municipal digested sludge requires that the product cake have low water content. To this end, we investigated the change in sludge dewaterability after the addition of fly ash to municipal digested sludge, dewatering of which is difficult because of its high organic content. The performance of the dewatering is compared with that of electroosmotic dewatering (EDW) and conventional mechanical dewatering (CMD). Fly ash classified by sieving to the size of 25–75 μm and >75 μm is added to the municipal digested sludge by 10, 20, and 50 wt% by wet base. When adding fly ash particles to municipal digested sludge, dewatering efficiency improved with smaller fly ash particle size and with increase in the amount. When sludge was dewatered using an electroosmotic dewatering method, the dewatering efficiency is improved about 40% by adding fly ash of 25–75 μm particle size with 20 wt% when compared with conventional mechanical dewatering method without adding the fly ash. It is concluded that fly ash particles rich in inorganic material are helpful in the dewatering process when added to municipal digested sludge and EDW is more effective than CDW.     

Handling leachate from glass cullet stockpiles

Mixed glass cullet (crushed recycled glass containers) is stockpiled uncovered before use as roadway construction aggregate or daily cover in landfills. Rainwater that leaches through the stockpiles dissolves and suspends contaminants such as those from food residuals and paper labels. The objective of this study was to determine leachate quantity and quality from cullet stockpiles as a basis for development of Best Management Practices (BMPs). Four 35-tonne field stockpiles were set up for leachate analysis and to determine the effects of mechanical turning treatment on the leachate. Field-collected leachate and laboratory-generated washwater of cullet (water:cullet = 3:1 by weight) were both analyzed for basic wastewater parameters, which showed pollutant levels comparable to or higher than those of untreated domestic wastewater or urban stormwater. While organic contamination decreased substantially (e.g., washwater BOD > 95% reduction), TKN and total-phosphorus levels in leachate ranged between 11.6–154 mg L^?1 and 1.6–12.0 mg L^?1, respectively, and remained comparable to levels found in untreated domestic wastewater after four months. Turning enhanced the degradation of the organic constituents inside the stockpiles, which was confirmed by elevated temperatures. Based on this study, leachate from glass cullet stockpiles should not be released to surface water. For leachate from long-term cullet stockpiles, release to groundwater should be only done after treatment to reduce nitrogen levels.     

Inertization of hazardous dredging spoils

Vitrification and production of ceramics materials starting from sediment excavated from Venice lagoon is described. This sediment is classified as toxic waste because contains several heavy metal ions and organic pollutants and was successfully vitrified at 1200-1350 degrees C. Twenty weight percentage of glass cullet, coming from a community glass recycling program, was added to the raw materials, previously calcined at 900 degrees C, as a way of adjusting the variations of composition of the individual sediment batches. Chemical durability (leaching) tests showed that the optimized glass compositions are inert, and thus not only volume reduction but also inertization of the waste was obtained by this process. Moreover, the economics of the entire process was analysed. The valorization of the waste was accomplished by the subsequent processing of the glass derived from the inertization. Glass ceramic materials were produced by viscous phase sintering of pressed glass powders which crystallized during the densification process. Sintered glass ceramic products had good mechanical characteristics (HV = 7.5 GPa, bending strength 150 +/- 8 MPa), making them suitable for applications in the building industry.     

Glass-ceramics from vitrified sewage sludge pyrolysis residues and recycled glasses

Pyrolysis of urban plant sewage sludge has been demonstrated to be an effective way to produce fuel gas. However, a complete disposal of this particular waste is not achieved if the solid residues from the treatment are not considered. In this paper we discuss the feasibility an integrated pyrolysis/vitrification/sintering approach, aimed at a “full” disposal: the pyrolysis residues are first converted into a glass, then transformed into glass–ceramics, by simple viscous flow sintering treatments, with or without additions of inexpensive recycled glasses and kaolin clay. The obtained products were demonstrated to constitute an alternative to natural stones, in terms of both mechanical strength and chemical stability.     

Recycling of Malaysia’s electric arc furnace (EAF) slag waste into heavy-duty green ceramic tile

Recently, various solid wastes from industry such as glass waste, fly ash, sewage sludge and slag have been recycled into various value-added products such as ceramic tile. The conventional solutions of dumping the wastes in landfills or incineration, including in Malaysia are getting obsolete as the annual huge amount of the solid wastes would boost-up disposal cost and may cause permanent damage to the flora and fauna. This recent waste recycling approach is much better and greener as it can resolve problems associated with over-limit storage of industrial wastes and reduce exploration of natural resources for ceramic tile to continuously sustain the nature. Therefore, in this project, an attempt was made to recycle electric arc furnace (EAF) slag waste, obtained from Malaysia’s steel making industry, into ceramic tile via conventional powder compaction method. The research work was divided into two stages. The first stage was to evaluate the suitability of EAF slag in ceramic tile by varying weight percentage of EAF slag (40 wt.%, 50 wt.% and 60 wt.%) and ball clay (40 wt.%, 50 wt.% and 60 wt.%), with no addition of silica and potash feldspar. In the second stage, the weight percentage of EAF slag was fixed at 40 wt.% and the percentage of ball clay (30 wt.% and 40 wt.%), feldspar (10 wt.% and 20 wt.%) and silica (10 wt.% and 20 wt.%) added was varied accordingly. Results obtained show that as weight percentage of EAF slag increased up to 60 wt.%, the percentage of apparent porosity and water absorption also rose, with a reduction in tile flexural strength and increased porosity. On the other hand, limiting the weight percentage of EAF slag to 40 wt.% while increasing the weight percentage of ball clay led to a higher total percentage of anorthite and wollastonite minerals, resulting in higher flexural strength. It was found that introduction of silica and feldspar further improved the flexural strength due to optimization of densification process. The highest flexural strength, lowest apparent porosity and water absorption of EAF slag based tile was attained at the composition of 40 wt.% EAF slag – 30 wt.% ball clay – 10 wt.% feldspar – 20 wt.% silica. The properties of ceramic tile made with EAF slag waste (up to 40 wt.%), especially flexural strength are comparable to those of commercial ceramic tile and are, therefore, suitable as high flexural strength and heavy-duty green ceramic floor tile. Continuous development is currently underway to improve the properties of tile so that this recycling approach could be one of the potential effective, efficient and sustainable solutions in sustaining our nature.     

Copper stabilization in beneficial use of waterworks sludge and copper-laden electroplating sludge for ceramic materials

A promising strategy for effectively incorporating metal-containing waste materials into a variety of ceramic products was devised in this study. Elemental analysis confirmed that copper was the predominant metal component in the collected electroplating sludge, and aluminum was the predominant constituent of waterworks sludge collected in Hong Kong. The use of waterworks sludge as an aluminum-rich precursor material to facilitate copper stabilization under thermal conditions provides a promising waste-to-resource strategy. When sintering the mixture of copper sludge and the 900 °C calcined waterworks sludge, the CuAl₂O₄ spinel phase was first detected at 650 °C and became the predominant product phase at temperatures higher than 850 °C. Quantification of the XRD pattern using the Rietveld refinement method revealed that the weight of the CuAl₂O₄ spinel phase reached over 50% at 850 °C. The strong signals of the CuAl₂O₄ phase continued until the temperature reached 1150 °C, and further sintering initiated the generation of the other copper-hosting phases (CuAlO₂, Cu₂O, and CuO). The copper stabilization effect was evaluated by the copper leachability of the CuAl₂O₄ and CuO via the prolonged leaching experiments at a pH value of 4.9. The leaching results showed that the CuAl₂O₄ phase was superior to the CuAlO₂ and CuO phases for immobilizing hazardous copper over longer leaching periods. The findings clearly indicate that spinel formation is the most crucial metal stabilization mechanism when sintering multiphase copper sludge with aluminum-rich waterworks sludge, and suggest a promising and reliable technique for reusing both types of sludge waste for ceramic materials.     

Coal fly ash utilization: low temperature sintering of wall tiles

We present here a study of the sintering of fly ash and its mixture with low alkali pyrophyllite in the presence of sodium hexa meta phosphate (SHMP), a complex activator of sintering, for the purpose of wall tile manufacturing. The sintering of fly ash with SHMP in the temperature range 925-1050 degrees C produces tiles with low impact strength; however, the incremental addition of low alkali pyrophyllite improves impact strength. The impact strength of composites with 40% (w/w) pyrophyllite in the fly ash-pyrophyllite mix satisfies the acceptable limit (19.6J/m) set by the Indian Standards Institute for wall tiles. Increasing the pyrophyllite content results in an increase in the apparent density of tiles, while shrinkage and water absorption decrease. The strength of fly ash tiles is attributed to the formation of a silicophosphate phase; in pyrophyllite rich tiles, it is attributed to the formation of a tridymite-structured T-AlPO(4) phase. Scanning electron micrographs show that the reinforcing rod shaped T-AlPO(4) crystals become more prominent as the pyrophyllite content increases in the sintered tiles.     

Application of sewage sludge compost on highway embankments

More and more sewage sludge is being produced in China. Safe and economical methods for sewage sludge disposal should be found considering the increase in sewage treatment. In order to verify the feasibility of sludge disposal on newly built highway embankments, five treatments (0, 15, 30, 60 and 120 tons ha⁻¹) of sewage sludge compost (SSC) were added to a silty-clay embankment soil on the Xi-Huang highway. The results showed that amendment with SSC increased soil available N, available P, organic matter, cation exchange capacity, and water content, and decreased soil bulk density. Application of SSC enhanced ryegrass growth and reduced runoff and soil erosion. Heavy metal losses from sediments in runoff remained constant or decreased relative to the control until a rate of 60 tons ha⁻¹ was exceeded, when heavy metal losses appeared to increase.     

Determination of total chlorine and bromine in solid wastes by sintering and inductively coupled plasma-sector field mass spectrometry

A sample preparation method based on sintering, followed by analysis by inductively coupled plasma-sector field mass spectrometry (ICP-SFMS) for the simultaneous determination of chloride and bromide in diverse and mixed solid wastes, has been evaluated. Samples and reference materials of known composition were mixed with a sintering agent containing Na₂CO₃ and ZnO and placed in an oven at 560 °C for 1 h. After cooling, the residues were leached with water prior to a cation-exchange assisted clean-up. Alternatively, a simple microwave-assisted digestion using only nitric acid was applied for comparison. Thereafter the samples were prepared for quantitative analysis by ICP-SFMS. The sintering method was evaluated by analysis of certified reference materials (CRMs) and by comparison with US EPA Method 5050 and ion chromatography with good agreement. Median RSDs for the sintering method were determined to 10% for both chlorine and bromine, and median recovery to 96% and 97%, respectively. Limits of detection (LODs) were 200 mg/kg for chlorine and 20 mg/kg for bromine. It was concluded that the sintering method is suitable for chlorine and bromine determination in several matrices like sewage sludge, plastics, and edible waste, as well as for waste mixtures. The sintering method was also applied for determination of other elements present in anionic forms, such as sulfur, arsenic, selenium and iodine.     

Utilization of municipal solid waste incineration (MSWI) fly ash in ceramic brick: product characterization and environmental toxicity

In this study, municipal solid waste incineration (MSWI) fly ash was used as a blending in making ceramic brick based on its characterization and an orthogonal test was performed to determine the optimal mixture ratio of the materials. Besides, the fired bricks made in accordance with the optimal mixture ratio were characterized for performance, phase transformation, microstructure, leaching toxicity of the heavy metals in accordance with GB/T 2542-92 (Detection methods for bricks analysis, China) and by means of XRD, SEM and leaching toxicity analysis. It was found that the optimal mixture ratio of materials (MSWI fly ash:red ceramic clay:feldspar:gang sand) was 20:60:10:10 by mass, and the optimal sintering temperature was 950 °C. Leaching results of heavy metals from sintered bricks were reduced considerably in comparison with those from green bricks prior to sintering process. The results as a whole suggested that utilization of MSWI fly ash in ceramic brick constituted a potential means of adding value.