Removal of 2,4-D from aqueous solution by the adsorbents from spent bleaching earth

The removal of 2,4-D (2,4-dichlorophenoxyacetic acid) from aqueous solutions by activated spent bleaching earths (SBE) was studied at 20 degrees C. Experiments were performed as a function of time, initial concentration, dose and particle size of the adsorbent. The Langmuir and Freundlich adsorption equations were fitted by the adsorption data obtained. The values of Langmuir and Freundlich constants were determined. The adsorption kinetic was found to follow Lagergren equation. Both the boundary layer and intraparticle diffusion played important roles in the adsorption rate of 2,4-D. As the size of the adsorbent increased, the time to reach equilibrium increased but adsorption capacity decreased.     

Removal of 2, 4‐D from aqueous solution by the adsorbents from spent bleaching earth

Abstract

The removal of 2, 4‐D (2, 4‐ dichlorophenoxyacetic acid) from aqueous solutions by activated spent bleaching earths (SBE) was studied at 20 °C. Experiments were performed as a function of time, initial concentration, dose and particle size of the adsorbent. The Langmuir and Freundlich adsorption equations were fitted by the adsorption data obtained. The values of Langmuir and Freundlich constants were determined. The adsorption kinetic was found to follow Lagergren equation. Both the boundary layer and intraparticle diffusion played important roles in the adsorption rate of 2, 4‐D. As the size of the adsorbent increased, the time to reach equilibrium increased but adsorption capacity decreased.     

改性松针对水体中铅(II)的吸附

探讨了改性松针(GXLsp)作为吸附剂对水体中铅离子的吸附性能,考察了吸附时间、溶液pH值、吸附剂用量、盐离子浓度、Pb(II)初始浓度及温度对改性松针吸附Pb(II)的影响。利用Langmuir和Freundlich等温线模型对实验数据进行非线性拟合分析,结果表明,Freundlich等温线模型能很好地描述松针对Pb(II)的吸附过程。热力学参数表明吸附是一个自发的吸热过程。改性松针对铅的吸附行为符合拟二级动力学方程,表明吸附过程是以化学吸附为主。在293K时松针对Pb(II)的饱和吸附量为318.3 mg/g,因此,GXLsp可作为一种高效低值生物质吸附剂以去除水体中重金属Pb(II)的污染。     

Adsorption of phosphate from aqueous solution onto alunite

The phosphate removal potential of alunite, a low cost and abundantly available material, has been investigated. The effects of calcination temperature and time of alunite, adsorbent particle size, pH and initial phosphate concentration on the phosphate adsorption by the calcined alunite have been studied. Phosphate removal was seen to increase with increasing calcination temperature, decreasing adsorbent particle size and pH. Adsorption of phosphate followed first-order rate kinetics. Langmuir and Freundlich adsorption isotherm constants and correlation coefficients were calculated and compared. It was concluded that the adsorption data of phosphate onto calcined alunite fitted to the Langmuir model more than Freundlich model. Specific surface areas of the calcined alunite were calculated at different calcination temperatures and particle sizes.     

Phenol removal from wastewater by adsorption on zeolitic composite

It is well known that adsorption is an efficient method of removal of various pollutants from wastewater. The present study examines the phenol removal from water by adsorption on a new material, based on zeolitic volcanic tuff. This compound contains zeolitic tuff and cellulose, another known adsorbent, in a mass ratio of 4 to 1. The performances of the new adsorbent composite were compared with those of a widely used adsorbent material, zeolitic volcanic tuff. The adsorbent properties were tested on batch synthetic solutions containing 1–10 mg L^?1 (1–10 ppm) phenol, at room temperature without pH adjustment. The influence of the adsorbent dose, pH and contact time on the removal degree of phenol from water was investigated. The experimental data were modeled using the Langmuir, Freundlich, and Temkin adsorption isotherms. The Langmuir model was found to best represent our data revealing a monolayer adsorption with a maximum adsorption capacity between 0.12 and 0.53 mg g^?1 at 25 °C, for 2.00 g of adsorbent, depending on the initial phenol concentration. The adsorption kinetic study was performed using a pseudo-first- and pseudo-second-order kinetic models illustrating that phenol adsorption on zeolite composite is well described by pseudo-first kinetic equations. Our results indicated that phenol adsorption on the new adsorbent composite is superior to that on the classic zeolite.     

Arsenic(V) removal with a Ce(IV)-doped iron oxide adsorbent

The removal of arsenic(V) by a new Ce-Fe adsorbent was evaluated under various conditions. Under an initial As(V) of 1.0 mg l(-1), the adsorption capacity of the Ce-Fe absorbent was constant around a value of 16 mgg(-1) over a wide pH range (3-7), while a maximum adsorption capacity of 8.3 mgg(-1) was obtained over a narrow pH range around 5.5 for activated alumina, a conventional adsorbent. Kinetics of adsorption obeys a pseudo-first-order rate equation with the rate constant K(ad) as 1.84 x 10(-3) min(-1). The pattern of adsorption of As(V) by the adsorbent fitted well both the Langmuir and Freundlich models. A Langmuir Q(0) of 70.4 mgg(-1) was obtained at an initial pH of 5.0 and temperature of 20 degrees C, significantly higher than those of other adsorbents reported. Phosphate seriously inhibited the removal of As(V) while fluoride did not compete with As(V) even at an F/As molar ratio as high as 30, suggesting that the adsorption sites for As(V) and fluoride were different. Salinity, hardness, and other inorganic anions such as Cl(-), NO(3)(-), and SO(4)(2-) had no apparent effect on As(V) adsorption. Fourier transform infrared spectra of Ce-Fe adsorbent before and after As(V) adsorption demonstrated that M-OH groups plays an important role for As(V) ions removal in the adsorption mechanisms of Ce-Fe adsorbent.     

Activated carbon from industrial solid waste as an adsorbent for the removal of Rhodamine-B from aqueous solution: kinetic and equilibrium studies

The activated carbon was prepared using industrial solid waste called sago waste and physico-chemical properties of carbon were carried out to explore adsorption process. The effectiveness of carbon prepared from sago waste in adsorbing Rhodamine-B from aqueous solution has been studied as a function of agitation time, adsorbent dosage, initial dye concentration, pH and desorption. Adsorption equilibrium studies were carried out in order to optimize the experimental conditions. The adsorption of Rhodamine-B onto carbon followed second order kinetic model. Adsorption data were modeled using both Langmuir and Freundlich classical adsorption isotherms. The adsorption capacity Q0 was 16.12 mg g(-1) at initial pH 5.7 for the particle size 125-250 microm. The equilibrium time was found to be 150 min for 10, 20 mg l(-1) and 210 min for 30, 40 mg l(-1) dye concentrations, respectively. A maximum removal of 91% was obtained at natural pH 5.7 for an adsorbent dose of 100mg/50 ml of 10 mg l(-1) dye concentration and 100% removal was obtained when the pH was increased to 7 for an adsorbent dose of 275 mg/50 ml of 20 mg l(-1) dye concentration. Desorption studies were carried out in water medium by varying the pH from 2 to 10. Desorption studies were performed with dilute HCl and show that ion exchange is predominant dye adsorption mechanism. This adsorbent was found to be both effective and economically viable.     

Dynamic behaviour of Cd2+ adsorption in equilibrium batch studies by CaCO3 −-rich Corbicula fluminea shell

This work presents the structural and adsorption properties of the CaCO₃ ^?-rich Corbicula fluminea shell as a natural and economic adsorbent to remove Cd ions from aqueous solutions under batch studies. Experiments were conducted with different contact times, various initial concentrations, initial solution pH and serial biosorbent dosage to examine the dynamic characterization of the adsorption and its influence on Cd uptake capacity. The characterization of the C. fluminea shell using SEM/EDX revealed that the adsorbent surface is mostly impregnated by small particles of potentially calcium salts. The dominant Cd adsorption mechanism is strongly pH and concentration dependent. A maximum Cd removal efficiency of 96.20 % was obtained at pH 7 while the optimum adsorbent dosage was observed as 5 g/L. The Langmuir isotherm was discovered to be more suitable to represent the experimental equilibrium isotherm results with higher correlation coefficients (R ²?>?0.98) than Freundlich (R ²?<?0.97).The correlation coefficient values (p?<?0.01) indicated the superiority of the Langmuir isotherm over the Freundlich isotherm.     

粉煤灰对水溶液中磷的吸附性能及机理

以粉煤灰为吸附剂去除溶液中的磷,考察了其吸附除P动力学特征、热力学特征以及溶液初始pH和粉煤灰投加量对吸附除P效果的影响,并对其吸附除P机理做了初步探讨。结果表明,在给定实验条件下,粉煤灰对P具有较好的去除效果,随着初始P浓度从10 mg/L升高到80 mg/L,平衡吸附量为0.46～2.44 mg P/g粉煤灰,吸附效率从92.2%降低至61.1%;对不同浓度的含P溶液,粉煤灰最适用量为0.6～1.5 g粉煤灰/mg P;相同反应条件下,当温度由25℃升高到45℃时,P初始吸附速率提高了3倍;粉煤灰对P的吸附过程能够较好地拟合Langmuir、Freundlich及D-R吸附等温模型,相关系数均在0.98以上。通过对吸附饱和的粉煤灰进行解析实验发现,初始P浓度较低(<50 mg/L)时,以化学吸附为主,而在初始P浓度较高(>80 mg/L)时,则以物理吸附为主。     

Removal of nickel (II) from aqueous solutions using marine macroalgae as the sorbing biomass

In the present study biosorption technique, the passive accumulation of metals by biomass, is used for the removal of nickel from aqueous medium. The brown algae, Sargassum sp., in its natural and acid treated forms are used as a low cost sorbent. The adsorption characteristics of nickel on Sargassum sp. are evaluated as a function of time, pH, adsorbent dosage and initial concentration of nickel. The equilibrium adsorption data are fitted to Freundlich and Langmuir adsorption isotherm models and the model parameters are evaluated. Both the models represent the experimental data satisfactorily. The adsorption follows Lagergren first order kinetic model. The monolayer adsorption capacities of natural and acid treated forms of algae as obtained from Langmuir adsorption model are found to be 181 and 250mg g(-1) respectively.     

Adsorptive removal of an acid dye by lignocellulosic waste biomass activated carbon: equilibrium and kinetic studies

Chemically prepared activated carbon material derived from palm flower was used as adsorbent for removal of Amido Black dye in aqueous solution. Batch adsorption studies were performed for the removal of Amido Black 10B (AB10B), a di-azo acid dye from aqueous solutions by varying the parameters like initial solution pH, adsorbent dosage, initial dye concentration and temperature with three different particle sizes such as 100 μm, 600 μm and 1000 μm. The zero point charge was pH 2.5 and the maximum adsorption occurred at the pH 2.3. Experimental data were analyzed by model equations such as Langmuir, Freundlich and Temkin isotherms and it was found that the Freundlich isotherm model best fitted the adsorption data and the Freundlich constants varied from (K_F) 1.214, 1.077 and 0.884 for the three mesh sizes. Thermodynamic parameters such as ΔG, ΔH and ΔS were also calculated for the adsorption processes and found that the adsorption process is feasible and it was the endothermic reaction. Adsorption kinetics was determined using pseudo first-order, pseudo second-order rate equations and also Elovich model and intraparticle diffusion models. The results clearly showed that the adsorption of AB10B onto lignocellulosic waste biomass from palm flower (LCBPF) followed pseudo second-order model, and the pseudo second-order rate constants varied from 0.059 to 0.006 (g mg⁻¹ min) by varying initial adsorbate concentration from 25 mg L⁻¹ to 100 mg L⁻¹. Analysis of the adsorption data confirmed that the adsorption process not only followed intraparticle diffusion but also by the film diffusion mechanism.     

改性玉米秸秆吸附Cu^2＋的动力学和热力学

本研究用ZnCl2作为活化剂,使用功率640W的微波照射4min的方法制备改性玉米秸秆。考察投加量、pH、吸附时间对吸附性能的影响,并对等温吸附特征、吸附动力学和热力学进行了系统研究。结果表明：投加量为0．2g,pH为6,改性玉米秸秆对Cu^2＋具有很好的吸附效果,吸附在8h后达到平衡。该吸附过程符合Langmuir及Freundlich等温吸附模型和准二级动力学方程,其反应的吉布斯自由能△G〈0,为自发反应过程。     

The removal of uranium (VI) from aqueous solutions onto activated carbon developed from grinded used tire

In this study, activated carbon was prepared from waste tire by KOH chemical activation. The pore properties including the BET surface area, pore volume, pore size distribution, and average pore diameter were characterized. BET surface area of the activated carbon was determined as 558 m²/g. The adsorption of uranium ions from the aqueous solution using this activated carbon has been investigated. Various physico-chemical parameters such as pH, initial metal ion concentration, and adsorbent dosage level and equilibrium contact time were studied by a batch method. The optimum pH for adsorption was found to be 3. The removal efficiency has also been determined for the adsorption system as a function of initial concentration. The experimental results were fitted to Langmuir, Freundlich, and Dubinin–Radushkevich (D-R) isotherm models. A comparison of best-fitting was performed using the coefficient of correlation and the Langmuir isotherm was found to well represent the measured sorption data. According to the evaluation using the Langmuir equation, the saturated monolayer sorption capacity of uranium ions onto waste tire activated carbon was 158.73 mg/g. The thermodynamic equilibrium constant and the Gibbs free energy were determined and results indicated the spontaneous nature of the adsorption process. Kinetics data were best described by pseudo-second-order model.     

Preparation of activated carbon from dried pods of Prosopis cineraria with zinc chloride activation for the removal of phenol

Utilization of agrowaste materials for the production of activated carbon, as an excellent adsorbent with large surface area, is well established industrially, for dephenolation of wastewater. In the present work, dried pods of Prosopis cineraria—a novel and low-cost agrowaste material—were used to prepare activated carbons by zinc chloride activation. Batch adsorption experiments were carried out to study the effects of various physicochemical parameters such as initial phenol concentration, adsorbent dose, initial solution pH, and temperature. Pseudo-first-order second-order and diffusion kinetic models were used to identify the possible mechanisms of such adsorption process. The Langmuir and Freundlich equations were used to analyze the adsorption equilibrium. Maximum removal efficiency of 86 % was obtained with 25 mg?L^?1 of initial phenol concentration. The favorable pH for maximum phenol adsorption was 4.0. Freundlich equation represented the adsorption equilibrium data more ideally than the Langmuir. The maximum adsorption capacity obtained was 78.32 mg?g^?1 at a temperature of 30 °C and 25 mg?L^?1 initial phenol concentration. The adsorption was spontaneous and endothermic. The pseudo-second-order model, an indication of chemisorption mechanism, fitted the experimental data better than the pseudo-first-order Lagergren model. Regeneration of spent activated carbon was carried out using Pseudomonas putida MTCC 2252 as the phenol-degrading microorganism. Maximum regeneration up to 57.5 % was recorded, when loaded phenol concentration was 25 mg?L^?1. The data obtained in this study would be useful in designing and fabricating an efficient treatment plant for phenol-rich effluents.     

改性玉米秸秆吸附Cu2+的动力学和热力学

本研究用ZnCl2作为活化剂,使用功率640 W的微波照射4 min的方法制备改性玉米秸秆。考察投加量、pH、吸附时间对吸附性能的影响,并对等温吸附特征、吸附动力学和热力学进行了系统研究。结果表明:投加量为0.2 g,pH为6,改性玉米秸秆对Cu2+具有很好的吸附效果,吸附在8 h后达到平衡。该吸附过程符合Langmuir及Freundlich等温吸附模型和准二级动力学方程,其反应的吉布斯自由能△G<0,为自发反应过程。     

溴化十六烷基吡啶改性沸石对水中甲基橙的吸附

采用溴化十六烷基吡啶(CPB)对天然沸石进行改性制备得到了CPB改性沸石,通过批量吸附实验考察了CPB改性沸石对水中阴离子染料甲基橙的去除作用。结果表明,天然沸石对水中甲基橙的吸附能力很差,而CPB改性沸石则可以有效吸附去除水中的甲基橙。CPB改性沸石对水中甲基橙的吸附能力随CPB负载量的增加而增加,CPB负载量最大的改性沸石对水中甲基橙的吸附能力最强。双分子层CPB改性沸石对水中甲基橙的去除率随吸附剂投加量的增加而增加,而CPB改性沸石对水中甲基橙的单位吸附量则随吸附剂投加量的增加而降低。双分子层CPB改性沸石对水中甲基橙的吸附平衡数据可以采用Langmuir等温吸附模型加以描述。根据Langmuir模型计算得到的CPB负载量为341 mmol/(kg沸石)的双分子层CPB改性沸石对水中甲基橙的最大吸附容量为63.7 mg/g(303 K和pH 7)。准二级动力学模型适合用于描述双分子层CPB改性沸石对水中甲基橙的吸附动力学过程。pH和反应温度对双分子层CPB改性沸石吸附水中甲基橙的影响较小。以上结果说明,双分子层CPB改性沸石适合作为一种吸附剂用于去除废水中的甲基橙。     

Performance evaluation of waste activated carbon on atrazine removal from contaminated water

In this study, the potential of spent activated carbon from water purifier (Aqua Guard, India) for the removal of atrazine (2 chloro-4 ethylamino-6-isopropylamino-1, 3, 5 triazine) from wastewaters was evaluated. Different grades of spent activated carbon were prepared by various pretreatments. Based on kinetic and equilibrium study results, spent activated carbon with a grain size of 0.3-0.5 mm and washed with distilled water (designated as WAC) was selected for fixed column studies. Batch adsorption equilibrium data followed both Freundlich and Langmuir isotherm. Fixed bed adsorption column with spent activated carbon as adsorbent was used as a polishing unit for the removal of atrazine from the effluent of an upflow anaerobic sludge blanket (UASB) reactor treating atrazine bearing domestic wastewater. Growth of bacteria on the surface of WAC was observed during column study and bacterial activity enhanced the effectiveness of adsorbent on atrazine removal from wastewater.     

粉煤灰砖块对磷酸盐的吸附特性

以建筑废料粉煤灰砖块为吸附剂材料,通过静态吸附实验研究其对磷酸盐的吸附特征,以及磷酸盐初始浓度、吸附剂投加量、pH等因素对吸附反应的影响。Langmuir、Freundlich和Temkin等温模型的分析发现,Langmuir等温式方程最适合描述吸附过程,对磷酸盐的理论饱和吸附容量为44.62 mg/g。利用伪一级动力学模型、伪二级动力学模型和颗粒内扩散模型考察了吸附过程特征,其中伪二级动力学模型为最适于描述粉煤灰砖块对磷酸盐的吸附过程的动力学模型。通过颗粒内扩散模型、Bangham方程及Boyd模型对吸附动力学机理进行的探讨表明,颗粒内扩散速率不是粉煤灰砖块吸附磷酸盐反应的惟一速率控制步,膜扩散速率和颗粒内扩散速率共同影响着吸附反应速率。磷酸盐浓度较低时主要是膜扩散限制吸附反应速率,而磷酸盐浓度较高时则颗粒内扩散成为速率控制步。研究证明,粉煤灰砖块粉末作为湿地基质具有对磷酸盐很强的吸附能力,在减少了固体废弃物的数量的同时又可以实现水污染控制的目的。     

Performance Evaluation of Waste Activated Carbon on Atrazine Removal from Contaminated Water

Abstract

In this study, the potential of spent activated carbon from water purifier (Aqua Guard, India) for the removal of atrazine (2 chloro-4 ethylamino-6-isopropylamino-1, 3, 5 triazine) from wastewaters was evaluated. Different grades of spent activated carbon were prepared by various pretreatments. Based on kinetic and equilibrium study results, spent activated carbon with a grain size of 0.3–0.5 mm and washed with distilled water (designated as WAC) was selected for fixed column studies. Batch adsorption equilibrium data followed both Freundlich and Langmuir isotherm. Fixed bed adsorption column with spent activated carbon as adsorbent was used as a polishing unit for the removal of atrazine from the effluent of an upflow anaerobic sludge blanket (UASB) reactor treating atrazine bearing domestic wastewater. Growth of bacteria on the surface of WAC was observed during column study and bacterial activity enhanced the effectiveness of adsorbent on atrazine removal from wastewater.     

Adsorption characteristics of 2,4-dichlorophenoxyacetic acid (2,4-D) from aqueous solution on powdered activated carbon

The removal of 2,4-dichlorophenoxyacetic acid (2,4-D), one of the most commonly used phenoxy acid herbicides, from aqueous solution was studied by using acid-washed powdered activated carbon (PAC) as an adsorbent in a batch system. Adsorption equilibrium, kinetics, and thermodynamics were investigated as a function of initial pH, temperature, and initial 2,4-D concentration. Powdered activated carbon exhibited the highest 2,4-D uptake capacity of 333.3 mg g(-1) at 25 degrees C and an initial pH value of 2.0. Freundlich, Langmuir, and Redlich-Peterson isotherm models were used to express the equilibrium data of 2,4-D depending on temperature. Equilibrium data fitted very well to the Freundlich equilibrium model in the studied concentration range of 2,4-D at all the temperatures studied. Three simplified models including pseudo-first-order, pseudo-second-order, and saturation-type kinetic models were used to test the adsorption kinetics. It was shown that the adsorption of 2,4-D on PAC at 25, 35, and 45 degrees C could be best fitted by the saturation-type kinetic model with film and intraparticle diffusions being the essential rate-controlling steps. The activation energy of adsorption (EA) was determined as--1.69 kJ mole(-1). Using the thermodynamic equilibrium coefficients obtained at different temperatures, the thermodynamic constants of adsorption (deltaG degrees, deltaH degrees, and deltaS degrees) were also evaluated.