Passenger muscle responses in lane change and lane change with braking maneuvers using two belt configurations: Standard and reversible pre-pretensioner

Abstract

Objective: The introduction of integrated safety technologies in new car models calls for an improved understanding of the human occupant response in precrash situations. The aim of this article is to extensively study occupant muscle activation in vehicle maneuvers potentially occurring in precrash situations with different seat belt configurations.

Methods: Front seat male passengers wearing a 3-point seat belt with either standard or pre-pretensioning functionality were exposed to multiple autonomously carried out lane change and lane change with braking maneuvers while traveling at 73?km/h. This article focuses on muscle activation data (surface electromyography [EMG] normalized using maximum voluntary contraction [MVC] data) obtained from 38 muscles in the neck, upper extremities, the torso, and lower extremities. The raw EMG data were filtered, rectified, and smoothed. All muscle activations were presented in corridors of mean?±?one standard deviation. Separate Wilcoxon signed ranks tests were performed on volunteers’ muscle activation onset and amplitude considering 2 paired samples with the belt configuration as an independent factor.

Results: In normal driving conditions prior to any of the evasive maneuvers, activity levels were low (<2% MVC) in all muscles except for the lumbar extensors (3–5.5% MVC). During the lane change maneuver, selective muscles were activated and these activations restricted the sideway motions due to inertial loading. Averaged muscle activity, predominantly in the neck, lumbar extensor, and abdominal muscles, increased up to 24% MVC soon after the vehicle accelerated in lateral direction for all volunteers. Differences in activation time and amplitude between muscles in the right and left sides of the body were observed relative to the vehicle’s lateral motion. For specific muscles, lane changes with the pre-pretensioner belt were associated with earlier muscle activation onsets and significantly smaller activation amplitudes than for the standard belt (P?<?.05).

Conclusions: Applying a pre-pretensioner belt affected muscle activations; that is, amplitude and onset time. The present muscle activation data complement the results in a preceding publication, the volunteers’ kinematics and the boundary conditions from the same data set. An effect of belt configuration was also seen on previously published volunteers’ kinematics with lower lateral and forward displacements for head and upper torso using the pre-pretensioner belt versus the standard belt. The data provided in this article can be used for validation and further improvement of active human body models with active musculature in both sagittal and lateral loading scenarios intended for simulation of some evasive maneuvers that potentially occur prior to a crash.     

A new THOR shoulder design: a comparison with volunteers, the Hybrid III, and THOR NT

OBJECTIVE: Since the shoulders are rarely seriously injured in frontal or oblique collisions, they have been given low priority in the development of frontal impact crash test dummies. The shoulder complex geometry and its kinematics are of vital importance for the overall dummy kinematics. The shoulder complex also influences the risk of the safety belt slipping off the shoulder in oblique forward collisions. The first aim of this study was to develop a new 50th percentile male THOR shoulder design, while the second was to compare the new shoulder, mounted on a THOR NT dummy, with volunteer, THOR NT, and Hybrid III range of motion and stiffness data. The third aim was to test the repeatability of the new shoulder during dynamic testing and to see how the design behaves with respect to belt slippage in a 45 degrees far-side collision. METHODS: The new 50th percentile THOR shoulder design was developed with the aid of a shell model of the seated University of Michigan Transportation Research Institute (UMTRI) 50th percentile male with coordinates for joints and bony landmarks (Schneider et al., 1983). The new shoulder design has human-like bony landmarks for the acromion and coracoid processes. The clavicle curvature and length are also made similar to that of a male human, as is the range of motion in the anterior-posterior, superior-inferior, and medial-lateral directions. The new shoulder design was manufactured and tested under the same conditions that T?rnvall et al. (2005b) used to compare the shoulder range of motion for the volunteers, Hybrid III, and THOR Alpha. The new design was also tested in two dynamic test configurations: the first was a 0 degrees full-frontal test and the second was a 45 degrees far-side test. The dummy tests were conducted with an R-16 seat with a three-point belt, the Delta V was 27.0+/-0.5 km/h and the maximum peak acceleration was approximately 14.6+/-0.5 g for each test. RESULTS: A new shoulder design with geometry close to that of humans was developed to be retrofitted to the THOR NT dummy. The results showed that the range of motion for the new shoulder complex during static loading was larger by at least a factor of three, for the maximum load (200 N/arm), than that of either the Hybrid III or the THOR NT; this means it was more similar to the volunteers' range of motion. It was observed that the THOR NT with the new shoulder did not slide out of the shoulder belt during a far-side collision. The performance of the new shoulder was reasonably repeatable and stable during both the static tests and the sled tests. CONCLUSION: A new shoulder for the THOR NT has been designed and developed, and data from static range of motion tests and sled tests indicate that the new shoulder complex has the potential to function in a more human-like manner on the THOR dummy.     

Cervical vertebral motions and biomechanical responses to direct loading of human head

There is little known data characterizing the biomechanical responses of the human head and neck under direct head loading conditions. However, the evaluation of the appropriateness of current crash test dummy head-neck systems is easily accomplished. Such an effort, using experimental means, generates and provides characterizations of human head-neck response to several direct head loading conditions. Low-level impact loads were applied to the head and face of volunteers and dummies. The resultant forces and moments at the occipital condyle were calculated. For the volunteers, activation of the neck musculature was determined using electromyography (EMG). In addition, cervical vertebral motions of the volunteers have been taken by means of X-ray cineradiography. The Ethics Committee of Tsukuba University approved the protocol of the experiments in advance. External force of about 210 N was applied to the head and face of five volunteers with an average age of 25 for the duration of 100 msec or so, via a strap at one of four locations in various directions: (1) an upward load applied to the chin, (2) a rearward load applied to the chin without facial mask, (3) a rearward load applied to the chin with the facial mask, and (4) a rearward load applied to the forehead. The same impact force as those for the human volunteers was also applied to HY-III, THOR, and BioRID. We found that cervical vertebral motions differ markedly according to the difference in impact loading condition. Some particular characteristics are also found, such as the flexion or extension of the upper cervical vertebrae (C0, C1, and C2) or middle cervical vertebrae (C3-C4), showing that the modes of cervical vertebral motions are markedly different among the different loading conditions. We also found that the biofidelity of dummies to neck response characteristics of the volunteers at the low-level impact loads is in the order of BioRID, THOR, and HY-III. It is relevant in this regard that the BioRID dummy was designed for a low-severity impact environment, whereas THOR and HY-III were optimized for higher-severity impacts.     

Rear impact responses of different sized adult Hybrid III dummies

Rear impact sled tests were conducted using 5th, 50th, and 95th percentile Hybrid III dummies to evaluate proposed injury criteria. Different head restraint height (750, 800 mm) and backset (0, 50, 100 mm) positions were used to determine axial and shear forces, bending moments, and injury criteria (NIC, N(ij), and N(km)). The time sequence to attain each parameter was also determined. Three events were identified in the response. Event I was coincident with the maximum rearward motion of the torso, Event II occurred at the time of the peak upper neck flexion moment, and Event III occurred at the time of maximum rearward motion of the head. Parameters such as backset, head restraint height, seat-head restraint interaction, and anthropometry affected impact responses. Head rotations increased with increasing backset and increasing head restraint height. However, N(ij) and N(km) did not exhibit such clear trends. The 50th percentile dummy responded with consistent injury criteria values (e.g., the magnitude of the injury criteria increased with backset increase or head restraint height decrease). However, the 5th and 95th percentile dummies did not demonstrate such trends. These findings underscore the need to include subject anthropometry in addition to seat and head restraint characteristics for better assessment of rear impact responses.     

Injuries in Full-Scale Vehicle Side Impact Moving Deformable Barrier and Pole Tests Using Postmortem Human Subjects

Objective: To conduct near-side moving deformable barrier (MDB) and pole tests with postmortem human subjects (PMHS) in full-scale modern vehicles, document and score injuries, and examine the potential for angled chest loading in these tests to serve as a data set for dummy biofidelity evaluations and computational modeling.

Methods: Two PMHS (outboard left front and rear seat occupants) for MDB and one PMHS (outboard left front seat occupant) for pole tests were used. Both tests used sedan-type vehicles from same manufacturer with side airbags. Pretest x-ray and computed tomography (CT) images were obtained. Three-point belt-restrained surrogates were positioned in respective outboard seats. Accelerometers were secured to T1, T6, and T12 spines; sternum and pelvis; seat tracks; floor; center of gravity; and MDB. Load cells were used on the pole. Biomechanical data were gathered at 20 kHz. Outboard and inboard high-speed cameras were used for kinematics. X-rays and CT images were taken and autopsy was done following the test. The Abbreviated Injury Scale (AIS) 2005 scoring scheme was used to score injuries.

Results: MDB test: male (front seat) and female (rear seat) PMHS occupant demographics: 52 and 57 years, 177 and 166 cm stature, 78 and 65 kg total body mass. Demographics of the PMHS occupant in the pole test: male, 26 years, 179 cm stature, and 84 kg total body mass. Front seat PMHS in MDB test: 6 near-side rib fractures (AIS = 3): 160–265 mm vertically from suprasternal notch and 40–80 mm circumferentially from center of sternum. Left rear seat PMHS responded with multiple bilateral rib fractures: 9 on the near side and 5 on the contralateral side (AIS = 3). One rib fractured twice. On the near and contralateral sides, fractures were 30–210 and 20–105 mm vertically from the suprasternal notch and 90–200 and 55–135 mm circumferentially from the center of sternum. A fracture of the left intertrochanteric crest occurred (AIS = 3). Pole test PMHS had one near-side third rib fracture. Thoracic accelerations of the 2 occupants were different in the MDB test. Though both occupants sustained positive and negative x-accelerations to the sternum, peak magnitudes and relative changes were greater for the rear than the front seat occupant. Magnitudes of the thoracic and sternum accelerations were lower in the pole test.

Conclusions: This is the first study to use PMHS occupants in MDB and pole tests in the same recent model year vehicles with side airbag and head curtain restraints. Injuries to the unilateral thorax for the front seat PMHS in contrast to the bilateral thorax and hip for the rear seat occupant in the MDB test indicate the effects of impact on the seating location and restraint system. Posterolateral locations of fractures to the front seat PMHS are attributed to constrained kinematics of occupant interaction with torso side airbag restraint system. Angled loading to the rear seat occupant from coupled sagittal and coronal accelerations of the sternum representing anterior thorax loading contributed to bilateral fractures. Inward bending initiated by the distal femur complex resulting in adduction of ipsilateral lower extremity resulted in intertrochanteric fracture to the rear seat occupant. These results serve as a data set for evaluating the biofidelity of the WorldSID and federalized side impact dummies and assist in validating human body computational models, which are increasingly used in crashworthiness studies.     

Posture and belt fit in reclined passenger seats

Abstract

Objective: Highly reclined postures may be common among passengers in future automated vehicles. A laboratory study was conducted to address the need for posture and belt fit in these seating configurations.

Methods: In a laboratory vehicle mockup, the postures of 24 men and women with a wide range of body size were measured in a typical front vehicle seat at seat back angles of 23°, 33°, 43°, and 53°. Data were gathered with and without a sitter-adjusted headrest. Posture was characterized by the locations of skeletal joint centers estimated from digitized surface landmarks.

Results: Regression analysis demonstrated that the pelvis rotated rearward and lumbar spine flexion decreased with increasing recline. The lap portion of the 3-point belt was more rearward relative to the pelvis in more-reclined postures, and the torso portion crossed the clavicle closer to the midline of the body. Regression equations were developed to predict posture and belt fit variables as a function of passenger characteristics, seat back angle, and the use of the headrest.

Conclusions: Spine posture changes as the torso reclines in an automotive seat, and belt fit is altered by the change in posture. The results can be used to accurately position crash test dummies and computation human models and to guide the design of belt restraints.     

正面碰撞事故中大客车乘员损伤影响因素分析

为研究乘客在大客车正面碰撞事故中的损伤机理,建立某全承载大客车有限元模型,并通过试验验证有限元模型的仿真精度。基于验证模型对不同碰撞速度条件下大客车车身结构力学响应、生存空间、座椅固定件强度、乘员运动响应和损伤等进行综合分析及评价。结果表明:高速碰撞条件下,驾驶员生存空间容易被侵入,座椅固定件强度存在失效的风险;乘员头部、颈部和胸部的损伤值受碰撞速度、安全带类型和乘员位置影响较大;三点式安全带保护效果明显优于两点式安全带。     

Children's and Adults’ Comfort Experience of Extra Seat Belts When Riding in the Rear Seat of a Passenger Car

Objective: The objective of this study was to explore passengers’ comfort experience of extra seat belts during on-road driving in the rear seat of a passenger car and to investigate how the use of extra belts affects children's and adults’ attitudes to the product.

Methods: Two different seat belt systems were tested, criss-cross (CC) and backpack (BP), consisting of the standard 3-point belt together with an additional 2-point belt. In total, 32 participants (15 children aged 6–10, 6 youths aged 11–15, and 11 adults aged 20–79, who differed considerably in size, shape, and proportions) traveled for one hour with each system, including city traffic and highway driving. Four video cameras monitored the test subject during the drive. Subjective data regarding emotions and perceived discomfort were collected in questionnaires every 20 min. A semistructured interview was held afterwards.

Results: All participant groups accepted the new products and especially the increased feeling of safety (P <.01); 56% preferred CC and 44% preferred BP but the difference was not significant. In total, 81% wanted to have extra seat belts in their family car. CC was appreciated for its symmetry, comfort, and the perceived feeling of safety. Some participants found CC unpleasant because the belts tended to slip close to the neck, described as a strangling feeling. BP was simpler to use and did not cause annoyance to the neck in the way CC did. Instead, it felt asymmetric and to some extent less safe than CC. Body size and shape affected seat belt fit to a great extent, which in turn affected the experience of comfort, both initially and over time. Perceived safety benefit and experienced comfort were the most determinant factors for the attitude toward the extra seat belts. The extra seat belts were perceived as being better than the participants had expected before the test, and they became more used to them over time.

Conclusion: This exploratory study provided valuable knowledge from a user perspective for further development of new seat belt systems in cars. In addition to an increased feeling of safety, seat belt fit and comfort are supplementary influencing factors when it comes to gaining acceptance of new seat belt systems.     

The Influence of Enhanced Side Impact Protection on Kinematics and Injury Measures of Far- or Center-Seated Children in Forward-Facing Child Restraints

Objective: To evaluate the influence of forward-facing child restraint systems’ (FFCRSs) side impact structure, such as side wings, on the head kinematics and response of a restrained, far- or center-seated 3-year-old anthropomorphic test device (ATD) in oblique sled tests.

Methods: Sled tests were conducted utilizing an FFCRS with large side wings and with the side wings removed. The CRS were attached via LATCH on 2 different vehicle seat fixtures—a small SUV rear bench seat and minivan rear bucket seat—secured to the sled carriage at 20° from lateral. Four tests were conducted on each vehicle seat fixture, 2 for each FFCRS configuration. A Q3s dummy was positioned in FFCRS according to the CRS owner's manual and FMVSS 213 procedures. The tests were conducted using the proposed FMVSS 213 side impact pulse. Three-dimensional motion cameras collected head excursion data. Relevant data collected during testing included the ATD head excursions, head accelerations, LATCH belt loads, and neck loads.

Results: Results indicate that side wings have little influence on head excursions and ATD response. The median lateral head excursion was 435 mm with side wings and 443 mm without side wings. The primary differences in head response were observed between the 2 vehicle seat fixtures due to the vehicle seat head restraint design. The bench seat integrated head restraint forced a tether routing path over the head restraint. Due to the lateral crash forces, the tether moved laterally off the head restraint reducing tension and increasing head excursion (477 mm median). In contrast, when the tether was routed through the bucket seat's adjustable head restraint, it maintained a tight attachment and helped control head excursion (393 mm median).

Conclusion: This testing illustrated relevant side impact crash circumstances where side wings do not provide the desired head containment for a 3-year-old ATD seated far-side or center in FFCRS. The head appears to roll out of the FFCRS even in the presence of side wings, which may expose the occupant to potential head impact injuries. We postulate that in a center or far-side seating configuration, the absence of door structure immediately adjacent to the CRS facilitates the rotation and tipping of the FFCRS toward the impact side and the roll-out of the head around the side wing structure. Results suggest that other prevention measures, in the form of alternative side impact structure design, FFCRS vehicle attachment, or shared protection between the FFCRS and the vehicle, may be necessary to protect children in oblique side impact crashes.     

Development of a three-year-old child FE model

OBJECTIVE: Child crash dummies are conventionally used for safety performance evaluations of the child restraint system (CRS) in vehicle crash tests. To investigate injuries to various body regions of a child in detail, mathematical models are useful, and provide information that cannot be analyzed by crash dummies. Therefore, in the present research, a finite element (FE) model of a 3-year-old child has been developed by model-based scaling from the AM50 human FE model, THUMS (Total HUman body for Safety). METHODS: The dimensions of each body region were based on the anthropometry data of United States children, and material properties of child bone were estimated from data reported in the literature. Neck flexion, thorax impact responses, and torso flexion were validated against the response corridor of the 3-year-old Hybrid III dummy in calibration tests. A test of lap belt loading to the abdomen was also conducted. FE models of two different types of CRS, a 5-point harness and a tray shield CRS, were also made, and ECE R44 sled impact test simulations were conducted using the child FE model. RESULTS: The characteristics of the child FE model proved to be close to the Hybrid III and child volunteer corridor. In the ECE R44 sled test simulations using the child FE model, the head movement down and head rotation were large in the 5-point harness CRS, and chest deflection was large in the tray shield CRS. In both CRS types, the whole spine flexed in the child FE model. This behavior is different from that of the Hybrid III, where the thorax spine is stiff and only the cervical spine and lumbar spine flex. CONCLUSIONS: Although this child FE model has several limitations in areas such as the anatomical shapes and material properties of a child, this model can be a useful tool to examine the behavior of a child in impacts, which may be difficult to predict by using the Hybrid III dummy with its stiff thorax spine box.     

Influence of seat properties on occupant dynamics in severe rear crashes

Seat performance in retaining an occupant, transferring energy, and controlling neck responses is often questioned after severe rear crashes when fatal or disabling injury occur. It is argued that a stiffer seat would have improved occupant kinematics. However, there are many factors in occupant interactions with the seat. This study evaluates four different seat types in 26 and 32 mph (42 and 51 km/h), rear crash delta Vs. Two seats were yielding with k = 20 kN/m occupant load per displacement. One represented a 1970s yielding seat with j = 3.4 degrees /kN frame rotation per occupant load, and 3 kN maximum load (660 Nm moment), and the other a high retention seat phased into production since 1997 with j = 1.4 degrees /kN, and 10 kN maximum load (2200 Nm). Two seats were stiff with k = 40 kN/m. One represented a 1990s foreign benchmark with j = 1.8 degrees /kN and a 7.7 kN maximum load (1700 Nm), and the other an all belts to seat (ABTS) with j = 1.0 degrees /kN and 20 kN maximum load (4400 Nm). The crash was a constant acceleration of 11.8 g, or 14.5 g for 100 ms. Occupant interactions with the seat were modeled using a torso mass, flexible neck and head mass. By analysis of the equations of motion, the initial change in seatback angle (Deltatheta) is proportional to jk(y - x), the product jk and the differential motion between the vehicle (seat cushion) and occupant. The transition from 1970s-80s yielding seats to stronger seats of the 1990s involved an increase in k stiffness; however, the jk property did not change as frame structures became stronger. The yielding seats of the 1970s had jk = 68 degrees /m, while the stiff foreign benchmark seat had jk = 72 degrees /m. The foreign benchmark rotated about the same as the 1970s seat up to 50 ms in the severe rear crashes. While it was substantially stronger, it produced higher loads on the occupant, and the higher loads increased seatback rotations and neck responses. The ABTS seat had the lowest rotations but also caused high neck responses because of the greater loads on the torso. Neck displacement (d) is initially proportional to (k/m(T)) integral integral y, seat stiffness times the second integral of vehicle displacement divided by torso mass. As seat stiffness increases, head-torso acceleration, velocity, and neck displacement increase. This study shows that the jk seat property determines the initial seatback rotation in rear crashes. If a stronger seat has a higher stiffness, it rotates at higher loads on the occupant, reducing the overall benefit of the stronger frame, while increasing neck responses related to whiplash or neck extension prior to subsequent impacts. The aim of seat designs should be to reduce jk, provide pocketing of the pelvis, and give head-neck support for the best protection in severe rear crashes. For low-speed crashes, a low k is important to reduce early neck responses related to whiplash.     

A comparison of injury criteria used in evaluating seats for whiplash protection

A protocol has been proposed for testing seats for whiplash protection, however injury criteria have not yet been chosen. Assuming that whiplash symptoms arise from non-physiological motions of vertebral segments, we determined the ability of proposed criteria to predict peak individual vertebral displacements. Twenty-eight volunteers were subjected to rear impacts while seated in a car seat with head restraint, mounted onto a sled. Accelerometers were used to record head and torso accelerations. The volunteer data was used as a basis for testing post-mortem human specimens (PMHS). The seat was replaced by a platform onto which was mounted each of 11 cervico-thoracic spines. An instrumented headform was mounted to the upper end of the spine. The head restraint, head-to-restraint geometry, sled, and impact pulse remained the same. Head and T1 accelerations were measured and individual vertebral sagittal (XZ) plane rotations and translations were obtained from high speed video. Proposed injury criteria (NIC, Nkm, Nte, Nd) were tested for their ability to predict average, total, and peak intervertebral displacements. PMHS specimens had chest and head X (horizontal) and Z (vertical) linear accelerations similar to volunteers whose heads hit the head restraint. The best predictors were: Nd shear and peak intervertebral posterior translation (r(2) = 0.80), Nd extension and peak extension angle (r(2) = 0.70), and Nd distraction and peak distraction (r(2) = 0.51). Therefore consideration should be given to a displacement based injury criteria such as Nd in assessment of whiplash protection devices.     

A new method for calculating saddle seat height with an emphasis on optimal posture based on trigonometric relations

Introduction. Based on the literature, the ergonomic saddle chair provides the most appropriate posture for users. Determination of the seat height is critical to establish the proper posture, carried out using various methods of anthropometry. This study aimed to develop a simple and applied method for determining the saddle seat height with an emphasis on appropriate posture. Methods. In this study, anthropometric dimensions including weight, body height, popliteal height and seat height at 135° knee angle in 150 male and female dentists were measured. In the laboratory, to determine the ‘acetabuloischial number’, 25 male and female natural hip bones were measured. The mean saddle-chair height with knee angle of 135° was then compared by two different methods, field measurement and the new calculation method. Results. The results showed a strong correlation between data gathered from the two different methods, the field measurement and the new calculation method (98%), and Cronbach’s α from the intraclass correlation was equal to 0.994 (p?<?0.05). This indicated that the two methods produced similar results. Conclusion. The new method can be applied to calculate the optimal height of the saddle seat based on body height and popliteal height.     

Influence of Seat Properties on Occupant Dynamics in Severe Rear Crashes

Seat performance in retaining an occupant, transferring energy, and controlling neck responses is often questioned after severe rear crashes when fatal or disabling injury occur. It is argued that a stiffer seat would have improved occupant kinematics. However, there are many factors in occupant interactions with the seat. This study evaluates four different seat types in 26 and 32 mph (42 and 51 km/h), rear crash delta Vs. Two seats were yielding with k = 20 kN/m occupant load per displacement. One represented a 1970s yielding seat with j = 3.4°/kN frame rotation per occupant load, and 3 kN maximum load (660 Nm moment), and the other a high retention seat phased into production since 1997 with j = 1.4°/kN, and 10 kN maximum load (2200 Nm). Two seats were stiff with k = 40 kN/m. One represented a 1990s foreign benchmark with j = 1.8°/kN and a 7.7 kN maximum load (1700 Nm), and the other an all belts to seat (ABTS) with j = 1.0°/kN and 20 kN maximum load (4400 Nm). The crash was a constant acceleration of 11.8 g, or 14.5 g for 100 ms. Occupant interactions with the seat were modeled using a torso mass, flexible neck and head mass. By analysis of the equations of motion, the initial change in seatback angle (Δθ) is proportional to jk(y ? x), the product jk and the differential motion between the vehicle (seat cushion) and occupant. The transition from 1970s–80s yielding seats to stronger seats of the 1990s involved an increase in k stiffness; however, the jk property did not change as frame structures became stronger. The yielding seats of the 1970s had jk = 68°/m, while the stiff foreign benchmark seat had jk = 72°/m. The foreign benchmark rotated about the same as the 1970s seat up to 50 ms in the severe rear crashes. While it was substantially stronger, it produced higher loads on the occupant, and the higher loads increased seatback rotations and neck responses. The ABTS seat had the lowest rotations but also caused high neck responses because of the greater loads on the torso. Neck displacement (d) is initially proportional to (k/m_T) ∫∫ y, seat stiffness times the second integral of vehicle displacement divided by torso mass. As seat stiffness increases, head-torso acceleration, velocity, and neck displacement increase. This study shows that the jk seat property determines the initial seatback rotation in rear crashes. If a stronger seat has a higher stiffness, it rotates at higher loads on the occupant, reducing the overall benefit of the stronger frame, while increasing neck responses related to whiplash or neck extension prior to subsequent impacts. The aim of seat designs should be to reduce jk, provide pocketing of the pelvis, and give head-neck support for the best protection in severe rear crashes. For low-speed crashes, a low k is important to reduce early neck responses related to whiplash.     

大客车正面碰撞乘客约束系统仿真分析

为探究约束系统在全承载客车正面碰撞事故中对乘客损伤的影响,利用有限元分析软件LSDYNA建立某大客车正面碰撞仿真模型,并开展整车50 km/h正面100%重叠碰撞固定刚性壁障试验;从车身变形、加速度曲线和乘员损伤等3方面验证仿真模型;基于已验证的仿真模型,开展不同座椅间距、车厢位置及安全带类型的乘员运动响应和损伤等综合分析与评价。研究结果表明:不同位置车身加速度波形整体趋势相似,但具体峰值和出现时刻存在差异;增大座椅间距和主动预紧安全带能够有效降低降低头部损伤值,而颈部损伤则随之增大;乘客胸部损伤值和大腿力受主动预紧安全带、座椅间距和车厢位置影响不大。     

Development and Validation of the Total HUman Model for Safety (THUMS) Toward Further Understanding of Occupant Injury Mechanisms in Precrash and During Crash

Objective: Active safety devices such as automatic emergency brake (AEB) and precrash seat belt have the potential to accomplish further reduction in the number of the fatalities due to automotive accidents. However, their effectiveness should be investigated by more accurate estimations of their interaction with human bodies. Computational human body models are suitable for investigation, especially considering muscular tone effects on occupant motions and injury outcomes. However, the conventional modeling approaches such as multibody models and detailed finite element (FE) models have advantages and disadvantages in computational costs and injury predictions considering muscular tone effects. The objective of this study is to develop and validate a human body FE model with whole body muscles, which can be used for the detailed investigation of interaction between human bodies and vehicular structures including some safety devices precrash and during a crash with relatively low computational costs.

Methods: In this study, we developed a human body FE model called THUMS (Total HUman Model for Safety) with a body size of 50th percentile adult male (AM50) and a sitting posture. The model has anatomical structures of bones, ligaments, muscles, brain, and internal organs. The total number of elements is 281,260, which would realize relatively low computational costs. Deformable material models were assigned to all body parts. The muscle–tendon complexes were modeled by truss elements with Hill-type muscle material and seat belt elements with tension-only material. The THUMS was validated against 35 series of cadaver or volunteer test data on frontal, lateral, and rear impacts. Model validations for 15 series of cadaver test data associated with frontal impacts are presented in this article. The THUMS with a vehicle sled model was applied to investigate effects of muscle activations on occupant kinematics and injury outcomes in specific frontal impact situations with AEB.

Results and Conclusions: In the validations using 5 series of cadaver test data, force–time curves predicted by the THUMS were quantitatively evaluated using correlation and analysis (CORA), which showed good or acceptable agreement with cadaver test data in most cases. The investigation of muscular effects showed that muscle activation levels and timing had significant effects on occupant kinematics and injury outcomes. Although further studies on accident injury reconstruction are needed, the THUMS has the potential for predictions of occupant kinematics and injury outcomes considering muscular tone effects with relatively low computational costs.     

Chest injuries of elderly postmortem human surrogates (PMHSs) under seat belt and airbag loading in frontal sled impacts: Comparison to matching THOR tests

Abstract

Objective: The goal of the study was to develop experimental chest loading conditions that would cause up to Abbreviated Injury Scale (AIS) 2 chest injuries in elderly occupants in moderate-speed frontal crashes. The new set of experimental data was also intended to be used in the benchmark of existing thoracic injury criteria in lower-speed collision conditions.

Methods: Six male elderly (age >63) postmortem human subjects (PMHS) were exposed to a 35?km/h (nominal) frontal sled impact. The test fixture consisted of a rigid seat, rigid footrest, and cable seat back. Two restraint conditions (A and B) were compared. Occupants were restrained by a force-limited (2.5?kN [A] and 2?kN [B]) seat belt and a preinflated (16?kPa [A] and 11?kPa [B]; airbag). Condition B also incorporated increased seat friction. Matching sled tests were carried out with the THOR-M dummy. Infra-red telescoping rod for the assessment of chest compression (IRTRACC) readings were used to compute chest injury risk. PMHSs were exposed to a posttest injury assessment. Tests were carried out in 2 stages, using the outcome of the first one combined with a parametric study using the THUMS model to adjust the test conditions in the second. All procedures were approved by the relevant ethics board.

Results: Restraint condition A resulted in an unexpected high number of rib fractures (fx; 10, 14, 15 fx). Under condition B, the adjustment of the relative airbag/occupant position combined with a lower airbag pressure and lower seat belt load limit resulted in a reduced pelvic excursion (85 vs. 110?mm), increased torso pitch and a substantially lower number of rib fractures (1, 0, 4 fx) as intended.

Conclusions: The predicted risk of rib fractures provided by the THOR dummy using the C_max and PC Score injury criteria were lower than the actual injuries observed in the PMHS tests (especially in restraint condition A). However, the THOR dummy was capable of discriminating between the 2 restraint scenarios. Similar results were obtained in the parametric study with the THUMS model.     

Small female rib cage fracture in frontal sled tests

Objectives: The 2 objectives of this study are to (1) examine the rib and sternal fractures sustained by small stature elderly females in simulated frontal crashes and (2) determine how the findings are characterized by prior knowledge and field data.

Methods: A test series was conducted to evaluate the response of 5 elderly (average age 76 years) female postmortem human subjects (PMHS), similar in mass and size to a 5th percentile female, in 30 km/h frontal sled tests. The subjects were restrained on a rigid planar seat by bilateral rigid knee bolsters, pelvic blocks, and a custom force-limited 3-point shoulder and lap belt. Posttest subject injury assessment included identifying rib cage fractures by means of a radiologist read of a posttest computed tomography (CT) and an autopsy. The data from a motion capture camera system were processed to provide chest deflection, defined as the movement of the sternum relative to the spine at the level of T8.

?A complementary field data investigation involved querying the NASS-CDS database over the years 1997–2012. The targeted cases involved belted front seat small female passenger vehicle occupants over 40 years old who were injured in 25 to 35 km/h delta-V frontal crashes (11 to 1 o'clock).

Results: Peak upper shoulder belt tension averaged 1,970 N (SD = 140 N) in the sled tests. For all subjects, the peak x-axis deflection was recorded at the sternum with an average of ?44.5 mm or 25% of chest depth. The thoracic injury severity based on the number and distribution of rib fractures yielded 4 subjects coded as Abbreviated Injury Scale (AIS) 3 (serious) and one as AIS 5 (critical). The NASS-CDS field data investigation of small females identified 205 occupants who met the search criteria. Rib fractures were reported for 2.7% of the female occupants.

Conclusions: The small elderly test subjects sustained a higher number of rib cage fractures than expected in what was intended to be a minimally injurious frontal crash test condition. Neither field studies nor prior laboratory frontal sled tests conducted with 50th percentile male PMHS predicted the injury severity observed. Although this was a limited study, the results justify further exploration of the risk of rib cage injury for small elderly female occupants.     

Passenger use of and attitudes toward rear seat belts

Objectives: This study sought to identify attitudes toward belt use in the rear seat and to gain insight into the experiences of rear-seat passengers. Method: A telephone survey conducted between June and August 2016 targeted adult passengers who had recently ridden in the rear and who did not always wear their seat belt when doing so. Respondents were questioned regarding their reasons for not buckling up and possible conditions under which they would be more likely to buckle up during rear-seat travel. Results: Of 1163 recent rear-seat passengers, 72% reported always using their seat belt in the rear. Full-time belt use was lower among passengers who primarily travel in the rear of hired vehicles compared with personal vehicles. The most common explanation for not buckling up was that the back seat is safer than the front. Four out of five agreed they do not buckle up because of type of trip; two-thirds forget or do not see the need; and two-thirds agreed with reasons related to design, comfort, or usability issues. Nearly 40% agreed that they sometimes do not buckle up in the rear because there is no law requiring it. Conclusion: Many reasons for not using belts in the rear are similar to reasons in the front, such as forgetfulness, inconvenience, or discomfort. One difference is that many rear-seat passengers perceive using the belt is unnecessary because the back seat is safer than the front. More than half of part-time belt users and nonusers reported interventions such as rear seat belt reminders, stronger belt-use laws, and more comfortable belts would make them more likely to use their seat belt in the rear seat. Practical applications: This study identifies barriers to rear seat belt use that point to the need for a multi-faceted approach to increase belt use.     

Is seat belt usage by front seat passengers related to seat belt usage by their drivers?

INTRODUCTION: Unrestrained drivers and passengers are involved in a significant amount of fatalities and injuries in motor-vehicle crashes in the United States. While the literature documents the effectiveness of seat belt usage in reducing crash outcomes, such as fatalities and the severity of injuries, there is a need to evaluate the impact of seat belt usage by drivers and passengers in their respective vehicles. These findings could help develop effective education and enforcement strategies to enhance occupant safety. METHOD: This paper summarizes a study comparing seat belt usage rates of drivers and passengers based on whether or not the driver uses a seat belt. Observational data from 50 sites in the state of Nevada over 3 years are used for analyses. The data are stratified based on the gender of the driver and passengers in the front seat of the vehicle and are based on area type (rural or urban). RESULTS: A comparison of the rates of seat belt usage across for the aggregated data and for various types of disaggregation and statistical analyses to compare the rates of seat belt use among passengers based on the use of seat belts by drivers confirms that when drivers use seat belts, their respective passengers are much more likely to use seat belts. Further, if drivers do not use seat belts, their passengers are not likely to use seat belts. This observation is comparable for male drivers and female drivers, and also for male passengers and female passengers. Further, there are no differences for combinations of the genders of the drivers and passenger (i.e., both male or female, or one male and one female). IMPACT ON INDUSTRY: These results suggest that education and enforcement strategies would benefit most by working toward increasing seat belt usage rates among drivers.