Loofa egyptiaca as a novel adsorbent for removal of direct blue dye from aqueous solution

In this paper, Loofa egyptiaca (LE), an agricultural plant cultivated in Egypt, was used to prepare low-cost activated carbon (LE_C1 and LE_C2) adsorbents. The adsorbents (LE, LE_C1 and LE_C2) were evaluated for their ability to remove direct blue 106 dye from aqueous solutions. Batch mode experiments were conducted using various parameters such as pH, contact time, dye concentration and adsorbent concentration. The surface chemistry of LE, LE_C1 and LE_C2 was analyzed by scanning electron microscopy (SEM). The experimental data were examined using Langmuir, Freundlich, Temkin and Harkins–Jura isotherms. The results showed that the adsorption of direct blue 106 was maximal at the lowest value of pH (pH = 2). Removal efficiency was increased with an increase in dye concentration and a decrease in amount of adsorbent. Maximum adsorption capacity was found to be 57.14, 63.3 and 73.53 mg/g for LE, LE_C1 and LE_C2 respectively. Kinetics were also investigated using pseudo-first-order, pseudo-second-order and intra-particle diffusion models. The experimental data fitted very well with the pseudo-first-order and pseudo-second-order kinetic models. The results indicate that LE, LE_C1 and LE_C2 could be employed as adsorbents for the removal of direct blue dye from aqueous solutions.     

A two stage batch adsorber design for methylene blue removal to minimize contact time

The adsorption of methylene blue onto bentonite in a batch adsorber has been studied. Three kinetic models, the intraparticle diffusion equation and the pseudo first and second order equations, were selected to follow the adsorption process. Kinetic parameters, rate constants, equilibrium adsorption capacities and related correlation coefficients for each kinetic model were calculated and discussed. It was shown that the adsorption of methylene blue onto bentonite could be described by the pseudo second order equation. Adsorption of methylene blue onto bentonite followed the Langmuir isotherm. A model has been developed for the design of a two stage batch adsorber based on pseudo second order adsorption kinetics. The model has been optimized with respect to operating time in order to minimize total contact time to achieve a specified amount of methylene blue removal using a fixed mass of adsorbent. The results of two stage batch adsorber design studies showed that the required times for specified amounts of methylene blue removal significantly decreased. This design is particularly suitable for low-cost adsorbents/adsorption systems when minimising contact time is a major operational and design criterion and a significant volume of effluent needs to be treated in the minimum amount of time.     

Exploitation of Trichoderma harzianum mycelial waste for the removal of rhodamine 6G from aqueous solution

The harvested mycelial waste of Trichoderma harzianum was used as an adsorbent for the removal of rhodamine 6G and was studied in batch mode. The effects of agitation time and initial dye concentration, adsorbent dosage and pH were examined. The study revealed that the amount of dye adsorbed (mgg(-1)) increased with increase in agitation time and reached equilibrium after 120 min, for dye concentrations of 10-50 mg L(-1). The adsorbent dosage of 1.0 g/50 mL and pH of 8.0 were found to be optimum for maximum dye removal. The batch mode adsorption data followed both the Langmuir and Freundlich isotherms. The pseudo first- and second-order rate kinetics were applied to the adsorbent system. The adsorption kinetics of rhodamine 6G showed that the pseudo-second-order kinetic model provided the best correlation of the equilibrium data. The study implies that it is possible to develop a dye removal system by using T. harzianum biomass, which occurs as sludge in waste stream of fermentation industries.     

Development of activated carbon from Nerium oleander flower and their rapid adsorption of direct and reactive dyes

The present study investigates the thermally activated carbon derived from Nerium oleander flower which was used an adsorbent. Physicochemical properties of Nerium oleander flower carbon (NOFC) were characterized by scanning electron microscopy, X-ray diffraction, and Fourier transform infrared for the removal of DTB (Direct Turquoise Blue) and RR-HE7B (Reactive red–HE7B) dyes from aqueous solution. Adsorption studies were carried out with different pH, adsorbent dose, contact time, and initial concentration dye solution. Optimum conditions for maximum removal of DTB and RR-HE7B was achieved to be pH 2 for both dyes, adsorbent dose of 100 mg and equilibrium time of 35 and 60 min, respectively, for NOFC. The maximum adsorption capacity of NOFC was found to be 33.33 and 19.60 mg g^?1, respectively, for the removal of dye solution. The mechanism of adsorption was studied by using different kinetic models and isotherms. The results clearly showed that the NOFC adsorption was fitted to pseudo–first-order for DTB and pseudo–second-order for RR-HE7B. Equilibrium data were well fitted with both isotherm models. According to the results, NOFC can effectively remove DTB and RR-HE7B from aqueous solutions.     

Adsorption of basic dye from aqueous solution onto fly ash

The fly ash treated by H₂SO₄ was used as a low-cost adsorbent for the removal of a typical dye, methylene blue, from aqueous solution. An increase in the specific surface area and dye-adsorption capacity was observed after the acid treatment. The adsorption isotherm and kinetics of the treated fly ash were studied. The experimental results were fitted using Langmuir and Freundlich isotherms. It shows that the Freundlich isotherm is better in describing the adsorption process. Two kinetic models, pseudo-first order and pseudo-second order, were employed to analyze the kinetic data. It was found that the pseudo-second-order model is the better choice to describe the adsorption behavior. The thermodynamic study reveals that the enthalpy (ΔH⁰) value is positive (5.63 kJ/mol), suggesting an endothermic nature of the adsorption.     

Adsorption of methylene blue from aqueous solution by jackfruit (Artocarpus heteropyllus) leaf powder: A fixed-bed column study

Continuous fixed-bed studies were undertaken to evaluate the efficiency of jackfruit leaf powder (JLP) as an adsorbent for the removal of methylene blue (MB) from aqueous solution under the effect of various process parameters like bed depth (5–10 cm), flow rate (30–50 mL/min) and initial MB concentrations (100–300 mg/L). The pH at point of zero charge (pH_PZC) of the adsorbent was determined by the titration method and a value of 3.9 was obtained. A FTIR of the adsorbent was done before and after the adsorption to find the potential adsorption sites for interaction with methylene blue molecules. The results showed that the total adsorbed quantities and equilibrium uptake decreased with increasing flow rate and increased with increasing initial MB concentration. The longest breakthrough time and maximum MB adsorption were obtained at pH 10. The results showed that the column performed well at low flow rate. Also, breakthrough time and exhaustion time increased with increasing bed depth. The bed-depth service time (BDST) model and the Thomas model were applied to the adsorption of MB at different bed depths, flow rates, influent concentrations and pH to predict the breakthrough curves and to determine the characteristic parameters of the column that are useful for process design. The two model predictions were in very good agreement with the experimental results at all the process parameters studied indicating that they were very suitable for JLP column design.     

Removal of basic dye (Astrazon Blue FGRL) using macroalga Caulerpa lentillifera

The macroalga Caulerpa lentillifera was found to have adsorption capacity for a basic dye, Astrazon Blue FGRL. For the whole range of concentrations employed in this work (20-1280 mgl(-1)), the adsorption reached equilibrium within the first hour. The kinetic data corresponded well with the pseudo second-order kinetic model where the rate constants decreased as initial dye concentrations increased. At low dye concentrations (20-80 mgl(-1)), an increase in the adsorbent dosage resulted in a higher removal percentage of the dye, but a lower amount of dye adsorbed per unit mass (q). The adsorption isotherm followed both the Langmuir and Freundlich models within the temperature range employed in this work (18-70 degrees C). The highest maximum adsorption capacity (q(m)) was obtained at 50 degrees C. The enthalpy of adsorption was estimated at 14.87 kJmol(-1) suggesting a chemical adsorption mechanism.     

Mechanisms and chemistry of dye adsorption on manganese oxides-modified diatomite

The investigations into structural changes which occur during adsorbent modification and the adsorption mechanisms are essential for an effective design of adsorption systems. Manganese oxides were impregnated onto diatomite to form the type known as δ-birnessite. Initial investigations established the effectiveness of manganese oxides-modified diatomite (MOMD) to remove basic and reactive dyes from aqueous solution. The adsorption capacity of MOMD for methylene blue (MB), hydrolysed reactive black (RB) and hydrolysed reactive yellow (RY) was 320, 419, and 204 mg/g, respectively. Various analytical techniques were used to characterise the structure and the mechanisms of the dye adsorption process onto MOMD such as Fourier transform infrared (FTIR), X-ray diffraction (XRD) and atomic absorption spectrometry (A.A.). A small shift to higher values of the d-spacing of dye/MOMD was observed indicating that a small amount of the dye molecules were intercalated in the MOMD structure and other molecules were adsorbed on the external surface of MOMD. Two mechanisms of dye adsorption onto MOMD were proposed; intercalation of the dye in the octahedral layers and adsorption of the dye on the MOMD external surface. Moreover, the results demonstrated that the MOMD structure was changed upon insertion of MB and RY with an obvious decrease in the intensity of the second main peak of the MOMD X-ray pattern.     

Thermochemical esterifying citric acid onto lignocellulose for enhancing methylene blue sorption capacity of rice straw

In this paper, rice straw was esterified thermochemically with citric acid (CA) to produce potentially biodegradable cationic sorbent. The modified rice straw (MRS) and crude rice straw (CRS) were evaluated for their methylene blue (MB) removal capacity from aqueous solution. The effects of various experimental parameters (e.g., initial pH, sorbent dose, dye concentration, ion strength, and contact time) were examined. The ratio of MB sorbed on CRS increased as the initial pH was increased from pH 2 to 10. For MRS, the MB removal ratio came up to the maximum value beyond pH 3. The 1.5g/l or up of MRS could almost completely remove the dye from 250mg/l of MB solution. The ratio of MB sorbed kept above 98% over a range from 50 to 450mg/l of MB concentration when 2.0g/l of MRS was used. Increase in ion strength of solution induced decline of MB sorption. The isothermal data fitted the Langmuir model. The sorption processes followed the pseudo-first-order rate kinetics. The intraparticle diffusion rate constant (k(id)) was greatly increased due to modification.     

Utilization of powdered waste sludge (PWS) for removal of textile dyestuffs from wastewater by adsorption

Acid pre-treated powdered waste sludge (PWS) was used for removal of textile dyestuffs from aqueous medium by adsorption as an alternative to the use of powdered activated carbon (PAC). The rate and extent of dysetuff removals were determined for four different dyestuffs at different PWS concentrations varying between 1 and 6 gl(-1). Biosorbed dyestuff concentrations at equilibrium decreased with increasing PWS concentration for all dyestuffs tested. PWS was more effective for adsorption of Remazol red RR and Chrisofonia direct yellow 12 as compared to the other dyestuffs tested. More than 80% percent dyestuff removal was obtained for all dyestuffs at PWS concentrations above 4 gl(-1) after 6h of incubation. Similar to percent dyestuff removal, the rate of adsorption was maximum at a PWS concentration of 4 gl(-1). Kinetics of adsorption of dyestuffs was investigated by using the first- and second-order kinetic models and the kinetic constants were determined. Second-order kinetics was found to fit the experimental data better than the first-order model for all dyestuffs tested. Adsorption isotherms were established for all dyestuffs used and the isotherm constants were determined by using the experimental data. Langmuir and the generalized adsorption isotherms were found to be more suitable than the Freundlich isotherm for correlation of equilibrium adsorption data. Acid pre-treated PWS was proven to be an effective adsorbent for dyestuff removal as compared to the other adsorbents reported in literature studies.     

Azadirachta indica leaf powder as an effective biosorbent for dyes: a case study with aqueous Congo Red solutions

In the present work, the leaves of Azadirachta indica (locally known as the Neem tree) in the form of a powder were investigated as a biosorbent of dyes taking aqueous Congo Red solution as a model system. The sorbent was made from mature Neem leaves and was investigated in a batch reactor under variable system parameters such as concentration of the aqueous dye solution, agitation time, adsorbent amount, pH, and temperature. An amount of 0.6 g of the Neem leaf powder (NLP) per litre could remove 52.0-99.0% of the dye from an aqueous solution of concentration 2.87 x 10(-2) mmol l(-1) with the agitation time increasing from 60 to 300 min. The interactions were tested with respect to both pseudo first-order and second-order reaction kinetics; the latter was found to be more suitable. Considerable intra-particle diffusion was found to occur simultaneously. The sorption process was in conformity with Langmuir and Freundlich isotherms yielding values of the adsorption coefficients in the following ranges: Freundlich n: 0.12-0.19, Kf: 0.1039-0.2648 L g(-1); Langmuir qm: 41.24-128.26 g kg(-1), b: 443.3-1898.0 l mmol(-1), which supported favourable adsorption. The Langmuir monolayer capacity (qm) was high and the values of the coefficient b indicated the equilibrium, dye + NLP = dye...NLP being shifted overwhelmingly towards adsorption. Thermodynamically, the sorption process was exothermic with an average heat of adsorption of -12.75 kJ mol(-1). The spontaneity of the sorption process was also confirmed by the favourable values of Gibbs energy (mean values: -1.09 to -1.81 kJ mol(-1)) and entropy of adsorption (range: -18.97 to -56.32 J mol(-1)K(-1)). The results point to the effectiveness of the Neem leaf powder as a biosorbent for removing dyes like Congo Red from water.     

Kinetic and equilibrium isotherm studies for the adsorptive removal of Brilliant Green dye from aqueous solution by rice husk ash

The present study deals with the adsorption of Brilliant Green (BG) on rice husk ash (RHA). RHA is a solid waste obtained from the particulate collection equipment attached to the flue gas lines of rice husk fired boilers. Batch studies were performed to evaluate the influences of various experimental parameters like initial pH (pH0), contact time, adsorbent dose and initial concentration (C0) on the removal of BG. Optimum conditions for BG removal were found to be pH0 approximately 3.0, adsorbent dose approximately 6 g L(-1) of solution and equilibrium time approximately 5 h for the C0 range of 50-300 mg L(-1). Adsorption of BG followed pseudo-second-order kinetics. Intra-particle diffusion does not seem to control the BG removal process. Equilibrium isotherms for the adsorption of BG on RHA were analyzed by Freundlich, Langmuir, Redlich-Peterson (R-P), Dubnin-Radushkevich (D-R), and Temkin isotherm models using a non-linear regression technique. Langmuir and R-P isotherms were found to best represent the data for BG adsorption onto RHA. Adsorption of BG on RHA is favourably influenced by an increase in the temperature of the operation. Values of the change in entropy (DeltaS0) and heat of adsorption (DeltaH0) for BG adsorption on RHA were positive. The high negative value of change in Gibbs free energy (DeltaG0) indicates the feasible and spontaneous adsorption of BG on RHA.     

间接电化学降解亚甲基蓝废水的可行性研究

研究以ClO^-／Cl^-作媒介，间接电化学降解亚甲基蓝模拟废水的可行性。结果表明，亚甲基蓝的电化学降解与电极材料、电流密度以及添加剂种类等因素有关。以石墨为阳极，不锈钢为阴极，在无隔膜的烧杯中放置50ml浓度为1000mg/L的亚甲基蓝模拟废水，在室温25℃，pH6．0－8．0，槽电压10V，电流密度30．0mA/cm^2，Cl^-加入量2g/L的条件下，电解60min后，亚甲基蓝溶液的平均消色率达到98．0％，CODcr降解率为97．0％，BOD5降解率为99．0％；用浸涂过MnO2薄膜的石墨棒作阳极可显著加快其消解速率，而用浸涂过CeO2薄膜的石墨棒作阳极对其消解速率无明显的影响。并初步讨论了其降解机理。     

Platinum (IV) recovery from chloride solution by functionalized acrylic copolymers

Two acrylic adsorbents with different morphological structures and bearing amidoethylenamine and thiol groups were obtained and used for platinum sorption from chloride solution by the batch method. Physico-chemical parameters that influence adsorption such as initial Pt(IV) concentration, stirring time, pH, and adsorbent amount were investigated. The thermodynamic parameters of Pt(IV) sorption on the synthesized adsorbent were also evaluated based on Langmuir and Freundlich isotherms. Thermodynamic parameters estimated from Langmuir constants indicated that the adsorption is spontaneous, exothermic and there is a disordered state at the molecular level. The models used to analyze the sorption rate led to the conclusion that the most important step in the sorption of Pt(IV) could be both particle diffusion and chemical reaction of [PtCl₆]⁻ with amine functional groups. Thus, both the ion exchange and complex formation mechanisms can occur via nitrogen atoms in the recovery of Pt(IV) on the studied adsorbent.     

Rice husk ash as an effective adsorbent: evaluation of adsorptive characteristics for Indigo Carmine dye

Present study explored the adsorptive characteristics of Indigo Carmine (IC) dye from aqueous solution onto rice husk ash (RHA). Batch experiments were carried out to determine the influence of parameters like initial pH (pH(0)), contact time (t), adsorbent dose (m) and initial concentration (C(0)) on the removal of IC. The optimum conditions were found to be: pH(0)=5.4, t=8h and m=10.0 g/l. The pseudo-second-order kinetic model represented the adsorption kinetics of IC on to RHA. Equilibrium isotherms were analyzed by Freundlich, Langmuir, Temkin and Redlich-Peterson models using a non-linear regression technique. Adsorption of IC on RHA was favorably influenced by an increase in the temperature of the operation. The positive values of the change in entropy (DeltaS(0)) and heat of adsorption (DeltaH(0)); and the negative value of change in Gibbs free energy (DeltaG(0)) indicate feasible and spontaneous adsorption of IC on to RHA.     

咪唑银配位聚合物吸附偶氮染料研究

以咪唑银配位聚合物{Ag（im）}n作吸附剂,对偶氮染料刚果红和甲基橙的吸附进行了研究,结果表明：刚果红的最佳吸附条件是吸附剂加入量为31．5mg,温度为30℃,pH值为3,吸附时间为70min,最高染料脱除率为90。7％;甲基橙的最佳吸附条件是吸附剂加入量为36．7mg,温度为30℃,pH值为2,吸附时间为50min,最高染料脱除率为58．3％。     

Removal of chromium (VI) from aqueous solution using walnut hull

In this study, removal of chromium (VI) from aqueous solution by walnut hull (a local low-cost adsorbent) was studied. The extent of adsorption was investigated as a function of solution pH, contact time, adsorbent and adsorbate concentration, reaction temperature and supporting electrolyte (sodium chloride). The Cr (VI) removal was pH-dependent, reaching a maximum (97.3%) at pH 1.0. The kinetic experimental data were fitted to the first-order, modified Freundlich, intraparticle diffusion and Elovich models and the corresponding parameters were obtained. A 102.78 kJ/mol Ea (activation energy) for the reaction of chromium (VI) adsorption onto walnut indicated that the rate-limiting step in this case might be a chemically controlled process. Both the Langmuir and Freundlich isotherms were suitable for describing the biosorption of chromium (VI) onto walnut hull. The uptake of chromium (VI) per weight of adsorbent increased with increasing initial chromium (VI) concentration up to 240-480 mg/L, and decreased sharply with increasing adsorbent concentration ranging from 1.0 to 5.0 g/L. An increase in sodium chloride (as supporting electrolyte) concentration was found to induce a negative effect while an increase in temperature was found to give rise to a positive effect on the chromium (VI) adsorption process. Compared to the various other adsorbents reported in the literature, the walnut hull in this study shows very good promise for practical applicability.     

Removal of Pb(II) from wastewater using wheat bran

The adsorption of Pb(II) ions from aqueous solutions on wheat bran (WB) has been investigated as a function of initial concentration, adsorbent dose, adsorbent particle size, agitation speed, temperature, contact time and pH of solution. The equilibrium process was described well by the Langmuir isotherm model with maximum sorption capacities of 69.0, 80.7 and 87.0 mgg(-1) of Pb(II) on wheat bran at 20, 40 and 60 degrees C, respectively. Thermodynamic parameters, i.e. DeltaG(0), DeltaH(0) and DeltaS(0) have also been calculated for the system and the sorption process was found to be endothermic. Good correlation coefficients were obtained for the pseudo second-order kinetic model. The metal ion could be stripped by addition of 0.5M HCl, making the adsorbent regeneration and its reutilization possible.     

An Assessment of U(VI) removal from groundwater using biochar produced from hydrothermal carbonization

The ever-increasing growth of biorefineries is expected to produce huge amounts of lignocellulosic biochar as a byproduct. The hydrothermal carbonization (HTC) process to produce biochar from lignocellulosic biomass is getting more attention due to its inherent advantage of using wet biomass. In the present study, biochar was produced from switchgrass at 300 °C in subcritical water and characterized using X-ray diffraction, fourier transform infra-red spectroscopy, scanning electron micrcoscopy, and thermogravimetric analysis. The physiochemical properties indicated that biochar could serve as an excellent adsorbent to remove uranium from groundwater. A batch adsorption experiment at the natural pH (~3.9) of biochar indicated an H-type isotherm. The adsorption data was fitted using a Langmuir isotherm model and the sorption capacity was estimated to be ca. 2.12 mg of U g(-1) of biochar. The adsorption process was highly dependent on the pH of the system. An increase towards circumneutral pH resulted in the maximum adsorption of ca. 4 mg U g(-1) of biochar. The adsorption mechanism of U(VI) onto biochar was strongly related to its pH-dependent aqueous speciation. The results of the column study indicate that biochar could be used as an effective adsorbent for U(VI), as a reactive barrier medium. Overall, the biochar produced via HTC is environmentally benign, carbon neutral, and efficient in removing U(VI) from groundwater.     

Application of 'waste' wood-shaving bottom ash for adsorption of azo reactive dye

The utilization of wood-shaving bottom ash (WBA) for the removal of Red Reactive 141 (RR141), an azo reactive dye, was investigated. WBA/H(2)O and WBA/H(2)SO(4) were made by treating WBA with water and 0.1M H(2)SO(4), respectively, to increase adsorption capacity. Adsorption of RR141 from reactive dye solution (RDS) and reactive dye wastewater (RDW) by WBA/H(2)O and WBA/H(2)SO(4) involved the BET surface area and pore size diameter. Properties of adsorbents, effect of contact time, initial pH of solution, dissolved metals and elution studies indicated that the decolorisation mechanism involved both chemical adsorption and precipitation with calcium ions. In addition, the WBA/H(2)SO(4) surface might contain sulphate-cation complexes that were specific to enhancing dye adsorption from RDW. The adsorption isotherm had a best fit by the Freundlich model. Freundlich parameters showed that WBA/H(2)O used more heterogeneous surface than WBA/H(2)SO(4) and activated carbon for RDW adsorption. A thermodynamic study indicated that RDW adsorption was an endothermic process. The maximum dye adsorption capacities of WBA/H(2)O, WBA/H(2)SO(4) and activated carbon obtained from a Langmuir model at 30 degrees C were 24.3, 29.9, and 41.5mgl(-1), respectively. In addition, WBA/H(2)O and WBA/H(2)SO(4) could reduce colour and high chemical oxygen demand (COD) of real textile wastewater. According to the difficulty in the elution study, it was an environmentally safe disposal of this waste. Therefore, WBA, a waste from combustion of wood shavings, was suitable to be used as an effective adsorbent for azo reactive dye removal.