Municipal anaerobic digesters for codigestion, energy recovery, and greenhouse gas reductions.

Codigestion of five wastes and municipal wastewater sludge was evaluated using full-scale testing. Synergistic, antagonistic, and neutral outcomes were observed depending on codigestate identity and concentration, highlighting the value of careful blending. Yeast waste resulted in notable synergism, increasing biogas production by over 50%, whereas aircraft deicing waste resulted in antagonism at high loadings and neutral outcomes at lower loadings. Restaurant waste codigestion resulted in neutral outcomes. The synergisim with yeast codigestates may have resulted from trace nutrients (i.e., iron, nickel, and cobalt) in the wastes that increased microbiological activity. Antagonist outcomes with deicing waste may have been the result of organic overload or inhibitory deicer constituents. Codigestion of wastes at the feed rates investigated was estimated to produce 0.50 ML/d of methane having an energy equivalent of 17 500 MJ/d. This was estimated to reduce net carbon dioxide emissions by 560 tonnes/y.     

Oxidized starch solutions for environmentally friendly aircraft deicers

Deicers currently used for aircraft deicing, including ethylene glycol and propylene glycol, pose significant threats to surface waters, as a result of high biochemical oxygen demand (BOD) and toxicity to aquatic organisms. Oxidized starch may provide a less toxic deicer with lower BOD. The freezing point depression of starch formulations oxidized using hydrogen peroxide and catalysts (i.e., catalyzed hydrogen peroxide [H2O2] propagations-CHP) was 28 degrees C, and viscosities similar to those of commercial deicers were achieved after post-treatment with granular activated carbon. The most effective oxidized starch formulation exerted a 5-day BOD up to 6 times lower than glycol deicers (103 versus 400 to 800 g O2/L). Toxicity to Ceriodaphnia dubia for this formulation (48-hour lethal concentration, 50% [LC50] of 2.73 g/L) was greater than pure propylene glycol (13.1 g/ L), but lower than propylene glycol deicer formulations (1.02 g/L). Organic acids were identified by gas chromatography/mass spectrometry as the primary constituents in the oxidized starch solution. The proposed deicing system would provide effective deicing while exerting minimal environmental effects (e.g., lower toxicity to aquatic organisms and lower BOD). Furthermore, these deicers could be made from waste starch, promoting sustainability.     

Effects of deicing salt on the vitality and health of two spruce species,Picea abies Karst., and Picea glehnii Masters planted along roadsides in northern Japan

In northern Japan, the growth of Picea abies Karst., and Picea glehnii Masters, which have been planted along the highways, is often suppressed due to several environmental stresses. To examine the adverse effects of deicing salt, the primary source of stress,we measured needle life span, photosynthetic capacity, and water potential and transpiration rate of the two spruce species at a site with damaged trees, near the roadside and a site with healthy trees, located far from the highway. Results from the analysis showed large amounts of sodium and chlorine in the soil and snow at the damaged site. These elements had accumulated in the needles of the spruce. Moreover, physiological traits of the spruce, at the damaged site were also affected. Therefore, we concluded that poor physiological traits might be attributed to an accumulation of deicing salt in the needles, resulting in the suppression of tree growth.     

Road deicing salt irreversibly disrupts osmoregulation of salamander egg clutches

It has been postulated that road deicing salts are sufficiently diluted by spring rains to ameliorate any physiological impacts to amphibians breeding in wetlands near roads. We tested this conjecture by exposing clutches of the spotted salamander (Ambystoma maculatum) to three chloride concentrations (1 mg/L, 145 mg/L, 945 mg/L) for nine days, then transferred clutches to control water for nine days, and measured change in mass at three-day intervals. We measured mass change because water uptake by clutches reduces risks to embryos associated with freezing, predation, and disease. Clutches in controls sequestered water asymptotically. Those in the moderate concentrations lost 18% mass initially and regained 14% after transfer to control water. Clutches in high concentration lost 33% mass and then lost an additional 8% after transfer. Our results suggest that spring rains do not ameliorate the effects of deicing salts in wetlands with extremely high chloride concentrations.     

Electrical resistivity tomography as monitoring tool for unsaturated zone transport: an example of preferential transport of deicing chemicals

Non-invasive spatially resolved monitoring techniques may hold the key to observe heterogeneous flow and transport behavior of contaminants in soils. In this study, time-lapse electrical resistivity tomography (ERT) was employed during an infiltration experiment with deicing chemical in a small field lysimeter. Deicing chemicals like potassium formate, which frequently impact soils on airport sites, were infiltrated during snow melt. Chemical composition of seepage water and the electrical response was recorded over the spring period 2010. Time-lapse electrical resistivity tomographs are able to show the infiltration of the melt water loaded with ionic constituents of deicing chemicals and their degradation product hydrogen carbonate. The tomographs indicate early breakthrough behavior in parts of the profile. Groundtruthing with pore fluid conductivity and water content variations shows disagreement between expected and observed bulk conductivity. This was attributed to the different sampling volume of traditional methods and ERT due to a considerable fraction of immobile water in the soil. The results show that ERT can be used as a soil monitoring tool on airport sites if assisted by common soil monitoring techniques.     

Improved management of winter operations to limit subsurface contamination with degradable deicing chemicals in cold regions

This paper gives an overview of management considerations required for better control of deicing chemicals in the unsaturated zone at sites with winter maintenance operations in cold regions. Degradable organic deicing chemicals are the main focus. The importance of the heterogeneity of both the infiltration process, due to frozen ground and snow melt including the contact between the melting snow cover and the soil, and unsaturated flow is emphasised. In this paper, the applicability of geophysical methods for characterising soil heterogeneity is considered, aimed at modelling and monitoring changes in contamination. To deal with heterogeneity, a stochastic modelling framework may be appropriate, emphasizing the more robust spatial and temporal moments. Examples of a combination of different field techniques for measuring subsoil properties and monitoring contaminants and integration through transport modelling are provided by the SoilCAM project and previous work. Commonly, the results of flow and contaminant fate modelling are quite detailed and complex and require post-processing before communication and advising stakeholders. The managers’ perspectives with respect to monitoring strategies and challenges still unresolved have been analysed with basis in experience with research collaboration with one of the case study sites, Oslo airport, Gardermoen, Norway. Both scientific challenges of monitoring subsoil contaminants in cold regions and the effective interaction between investigators and management are illustrated.     

The contribution of aircraft emissions to the atmospheric sulfur budget

An atmospheric general circulation model including the atmospheric sulfur cycle has been used to investigate the impact of aircraft sulfur emissions on the global sulfur budget of the atmosphere. The relative contribution from aircraft sulfur to the atmospheric sulfate burden is larger than the ratio between aircraft emissions and surface emissions due to the calculated long turn-over time of aircraft sulfate (about 12 days). However, in terms of the sulfate mass balance, aircraft emissions are small, contributing about 1% of the total sulfate mass north of 40°N where the aircraft emissions are largest. Despite this small contribution to sulfate mass, the aircraft emissions could potentially significantly enhance the background number concentration of aerosol particles. Based on the model calculations the increased stratospheric background aerosol mass observed during the last decades cannot be explained by increased aircraft sulfur emissions.     

Rapid measurement of emissions from military aircraft turbine engines by downstream extractive sampling of aircraft on the ground: Results for C-130 and F-15 aircraft

Aircraft emissions affect air quality on scales from local to global. More than 20% of the jet fuel used in the U.S. is consumed by military aircraft, and emissions from this source are facing increasingly stringent environmental regulations, so improved methods for quickly and accurately determining emissions from existing and new engines are needed. This paper reports results of a study to advance the methods used for detailed characterization of military aircraft emissions, and provides emission factors for two aircraft: the F-15 fighter and the C-130 cargo plane. The measurements involved outdoor ground-level sampling downstream behind operational military aircraft. This permits rapid change-out of the aircraft so that engines can be tested quickly on operational aircraft. Measurements were made at throttle settings from idle to afterburner using a simple extractive probe in the dilute exhaust. Emission factors determined using this approach agree very well with those from the traditional method of extractive sampling at the exhaust exit. Emission factors are reported for CO₂, CO, NO, NO_x, and more than 60 hazardous and/or reactive organic gases. Particle size, mass and composition also were measured and are being reported separately. Comparison of the emissions of nine hazardous air pollutants from these two engines with emissions from nine other aircraft engines is discussed.     

Reducing Air Pollutant Emissions at Airports by Controlling Aircraft Ground Operations

Potential reductions in air pollutant emissions were determined for four strategies to control aircraft ground operations at two case study airports, Los Angeles and San Francisco International Airports. Safety, cost, and fuel savings associated with strategy implementation were examined.

Two strategies, aircraft towing and shutdown of one engine during taxi operations, provided significant emission reductions. However, there are a number of safety problems associated with aircraft towing. The shutdown of one engine while taxiing was found to be the most viable strategy because of substantial emission reductions, cost benefits resulting from fuel savings, and no apparent safety problems.     

Sequential box models for indoor air quality: Application to airliner cabin air quality

In this paper we present the development and application of a model for indoor air quality. The model represents a departure from the standard box models typically used for indoor environments which has applicability in residences and office buildings. The model has been developed for a physical system consisting of sequential compartments which communicate only with adjacent compartments. Each compartment may contain various source and sink terms for a pollutant as well as leakage, and air transfer from adjacent compartments. The mathematical derivation affords rapid calculation of equilibrium concentrations in an essentially unlimited number of compartments. The model has been applied to air quality in the passenger cabin of three commercial aircraft. Simulations have been performed for environmental tobacco smoke (ETS) under two scenarios, CO₂ and water vapor. Additionally, concentrations in one aircraft have been simulated under conditions different from the standard configuration. Results of the simulations suggest the potential for elevated concentrations of ETS in smoking sections of non-air-recirculating aircraft and throughout the aircraft when air is recirculated. Concentrations of CO₂ and water vapor are consistent with expected results. We conclude that this model may be a useful tool in understanding indoor air quality in general and on aircraft in particular.     

Realistic Mixing Depths for Above Ground Aircraft Emissions

Analysis of vertical temperature soundings at Los Angeles International Airport (LAX) shows that a conservative height of the inversion base for pollutant containment purposes is 490 ft (150 m). This altitude is considerably less than the 3000 ft (914 m) pollution containment altitude assumed by the EPA in preparing their emission inventory for the airport. (Figure 1.) After correcting the EPA emission inventory to reflect a real world inversion height, the emission inventory for aircraft at Los Angeles International Airport is estimated to be approximately 50% less. Aircraft thus become a less significant pollution source and consideration should be given to relaxing engine emission control requirements accordingly.

This paper examines current emission control philosophy, which according to the EPA should be based upon the significance of the particular polluting source. The problem of accounting for above ground aircraft emissions is then considered. Daily inversion height data are then used to determine a realistic vertical containment altitude for aircraft emissions. Problems in obtaining good inversion data are described. Finally, aircraft emissions at Los Angeles International Airport are adjusted to reflect real world inversion conditions on those days when the inversion height is low enough to influence significantly air pollution levels. Recommendations are made for additional research leading to possible change to NO_x emission control requirements for aircraft.     

Benzotriazoles, Alkylphenols and Bisphenol A in Municipal Wastewaters and in the Glatt River, Switzerland

- DOI: http://dx.doi.org/10.1065/espr2006.01.295 Background Many organic micropollutants occur at trace concentrations in municipal wastewater effluents and in the aquatic environment. Some of these xenobiotic chemicals can be considered as 'emerging' contaminants and some are suspect to have endocrine disrupting effects. Among the latter are nonylphenol (NP), octylphenol (OP) and bisphenol A (BPA), which deserve special attention due to their ubiquitous occurrence in the aquatic environment. The complexing agents benzotriazole (BT) and tolyltriazole (TT) are applied as anticorrosive agents (e.g. in cooling and hydraulic fluids, in antifreezing fluids, in aircraft deicing fluids, in dish washing liquids for silver protection), as antifogging agents and as intermediates for the synthesis of various chemicals. The environmental occurrence of NP and OP is caused by the fact that they are intermediate products (metabolites) in the biodegradation of alkylphenol polyethoxylate surfactants. BPA is globally used for the production of polycarbonate and epoxy resins. Methods BT, TT, NP, OP and BPA were quantitatively determined in municipal wastewater effluents in Switzerland and in the Glatt River. The analytes were enriched by solid-phase enrichment. BT and TT were determined underivatized by electrospray LC/tandem MS. Reversed-phase LC was performed on octylsilica columns with isocratic water/methanol elution. Multiple reaction monitoring of the positive ions provided selective and sensitive detection for reliable quantifications. NP, OP and BPA were determined by GC/MS after derivatization with N-methyl-N-(trimethylsilyl)-trifluoroacetamide. Results and Discussion BT and TT concentrations in primary and secondary effluents of municipal wastewater treatment plants varied from below 10 to 100 μg/L. The ranges of the concentrations in the Glatt River in ng/L were 636–3,690 for BT, 122–628 for TT, 68–326 for NP, 6–22 for OP and 9–76 for BPA. The corresponding mass flows in g/d were 93–1,870 for BT, 18–360 for TT, 24–183 for NP, 1–16 for OP and 2–72 for BPA. The concentrations and mass flows of NP in the River Glatt were drastically lower than the analogous values found 15 years ago. Thus, a substantially decreased environmental exposure can be observed due to the reduction of the use of alkyphenol polyethoxylate surfactants in Switzerland. The current concentrations of NP, OP and BPA are within the ranges reported for weakly impacted surface waters. Conclusion The investigated contaminants occur at quantitatively measurable but varying concentrations in municipal wastewaters and in the Glatt River reflecting their ubiquitous input into wastewaters and their different behaviour during biological wastewater treatment.     

Analysis of air pollution data at a mixed source location using boosted regression trees

This paper explores the use of boosted regression trees to draw inferences concerning the source characteristics at a location of high source complexity. Models are developed for hourly concentrations of nitrogen oxides (NO_X) close to a large international airport. Model development is discussed and methods to quantify model uncertainties developed. It is shown that good explanatory models can be developed and further, allowing for interactions between model variables significantly improves the model fits compared with non-interacting models. Methods are used to determine which variables exert most influence over predicted concentrations and to explore the NO_X dependency for each. Model predictions are used to estimate aircraft take-off contributions to total concentrations of NO_X and determine how these predictions are affected by annual variations in meteorological conditions and runway use patterns. Furthermore, the results relating to the aircraft contributions to total NO_X concentration are compared with those from a more detailed independent field campaign. Finally, we find empirical evidence that plumes from larger aircraft disperse more rapidly from the point of release compared with smaller aircraft. The reasons for this behaviour and the implications are discussed.     

Dust emissions created by low-level rotary-winged aircraft flight over desert surfaces

There is a dearth of information on dust emissions from sources that are unique to U.S. Department of Defense testing and training activities. Dust emissions of PM₁₀ and PM_2.5 from low-level rotary-winged aircraft travelling (rotor-blade ≈7 m above ground level) over two types of desert surfaces (i.e., relatively undisturbed desert pavement and disturbed desert soil surface) were characterized at the Yuma Proving Ground (Yuma, AZ) in May 2007. Fugitive emissions are created by the shear stress of the outflow of high speed air created by the rotor-blade. The strength of the emissions was observed to scale primarily as a function of forward travel speed of the aircraft. Speed affects dust emissions in two ways: 1) as speed increases, peak shear stress at the soil surface was observed to decline proportionally, and 2) as the helicopter's forward speed increases its residence time over any location on the surface diminishes, so the time the downward rotor-generated flow is acting upon that surface must also decrease. The state of the surface over which the travel occurs also affects the scale of the emissions. The disturbed desert test surface produced approximately an order of magnitude greater emission than the undisturbed surface. Based on the measured emission rates for the test aircraft and the established scaling relationships, a rotary-winged aircraft similar to the test aircraft traveling 30 km h^?1 over the disturbed surface would need to travel 4 km to produce emissions equivalent to one kilometer of travel by a light wheeled military vehicle also traveling at 30 km h^?1 on an unpaved road. As rotary-winged aircraft activity is substantially less than that of off-road vehicle military testing and training activities it is likely that this source is small compared to emissions created by ground-based vehicle movements.     

Passenger aircraft cabin air quality: trends, effects, societal costs, proposals

As aircraft operators have sought to substantially reduce propulsion fuel cost by flying at higher altitudes, the energy cost of providing adequate outside air for ventilation has increased. This has lead to a significant decrease in the amount of outside air provided to the passenger cabin, partly compensated for by recirculation of filtered cabin air. The purpose of this review paper is to assemble the available measured air quality data and some calculated estimates of the air quality for aircraft passenger cabins to highlight the trend of the last 25 years. The influence of filter efficiencies on air quality, and a few medically documented and anecdotal cases of illness transmission aboard aircraft are discussed. Cost information has been collected from the perspective of both the airlines and passengers. Suggestions for air quality improvement are given which should help to result in a net, multistakeholder savings and improved passenger comfort.     

Effect of salt and urban water samples on bacterivory by the ciliate, Tetrahymena thermophila

The effect of road salt on the eating of bacteria or bacterivory by the ciliate, Tetrahymena thermophila, was followed in non-nutrient Osterhout's solution with Escherichia coli expressing green fluorescent protein. Bacterivory was impaired at between 0.025 and 0.050% w/v but the ciliates appeared to have normal morphologies and motilities, whereas at above 0.1%, bacterivory was blocked and many ciliates died. By contrast, E. coli remained viable, suggesting salt could alter predator-prey relationships in microbial communities. In nutrient medium, salt was not toxic and the ciliates grew. After growth in salt, ciliates consumed bacteria in 0.2% salt, indicating the salt acclimation of bacterivory. Bacteria and ciliates were added to urban creek samples to compare their capacity to support exogenous bacterivory. Even though samples were collected weekly for a year and be expected to have fluctuating salt levels as a result of deicing, all creek samples supported a similar level of bacterivory.     

Jet Aircraft: A Growing Pollution Source

Pollution from jet aircraft is not a problem confined only to Los Angeles County but one which is of interest and concern wherever a major airport exists. Jet traffic at Los Angeles International Airport has increased from 80 flights daily in 1959 to nearly 1000 a day. This number will more than double in the next decade and its air pollution potential will increase in about the same proportion. The Air Pollution Control District investigated this new source of air pollution in Los Angeles County in 1959. In the absence of any previous research evidence or other information which would allow an evaluation of contaminant emissions from jet aircraft engines, it was necessary to develop original and novel test methods. These tests provided a starting point for a new study in 1968, to update the initial investigations and expand on them to include testing of emissions from a new generation of turbofan, as well as late model turbojet and turboprop engines. The primary interest of this study was to obtain as complete and comprehensive information as possible on the kinds and quantities of air contaminants emitted by jet aircraft, particularly at the Los Angeles International Airport. Equally important were the investigations on possible approaches to control of jet aircraft pollution, as well as the decisions as to the scope of the District’s legal jurisdiction in the field of aviation.     

Jet Aircraft Operations: Impact on the Air Environment

This paper is directed to those concerned with the air environment and its degradation by the burden of pollution from jet aircraft operations. A summary is presented of the results of a comprehensive air pollution study of jet aircraft operations at the Los Angeles International Airport (LAX). Included in the data obtained from this study are jet engine exhaust measurements for currently used turboprop, turbojet and turbofan engines; measurements of specific contaminants in the atmosphere inside and outside of passenger terminals and ticketing areas, and in aircraft cabins during ground operations including passenger loading and taxiing prior to takeoff; also presented are ambient air measurements in a two-mile radius of the airport. An evaluation is made of the emissions of contaminants from air transport operations and all related ground activities including motor vehicles, that contribute to the total atmospheric contaminant burden at the airport.     

Simulation of the Environmental Impact of an Airport on the Surrounding Air Quality

It is the purpose of this study to demonstrate the procedure involved in simulating those average and maximum pollutant concentrations at or around an airport which fall under the control of the Clean Air Act. The information is useful, when planning new or expanding existing airports, when estimating the impact of airports on the surrounding air quality, and when assessing the effectiveness of control procedures. Simulation of airport air quality requires the accurate assessment of the temporal and spatial emission patterns. This involves the tabulation of air traffic density by type and engine, make and model of aircraft, and engine mode number; the use of fuel by different aircraft; the pollutant emission rates by engine model and operational mode; the allocation of emission rates to the respective runways, turn-off points, taxi-ways, and parking areas, and the time each aircraft spent in the different operational modes. The resulting emission pattern for the Honolulu International Airport reflects scheduled and unscheduled commercial and military jet and piston aircraft and nonaircraft operations. Using this and the appropriate meteorological information average and maximum surface concentrations were calculated and compared with local ambient air quality standards. The calculation of concentrations is based on a newly developed diffusion model incorporating harmonic mean wind speeds for every degree of wind direction as determined by a Parzen maximum likelihood interpolation technique, and the assumption of log-normal concentration distributions. It is shown that for some pollutants the air quality standards are substantially exceeded, and it is concluded that airports may have a considerable adverse impact on their surrounding air quality.     

The impact of NOx,CO and VOC emissions on the air quality of Zurich airport

To study the impact of emissions at an airport on local air quality, a measurement campaign at the Zurich airport was performed from 30 June 2004 to 15 July 2004. Measurements of NO, NO₂, CO and CO₂ were conducted with open path devices to determine real in-use emission indices of aircraft during idling. Additionally, air samples were taken to analyse the mixing ratios of volatile organic compounds (VOC). Temporal variations of VOC mixing ratios on the airport were investigated, while other air samples were taken in the plume of an aircraft during engine ignition. CO concentrations in the vicinity of the terminals were found to be highly dependent on aircraft movement, whereas NO concentrations were dominated by emissions from ground support vehicles. The measured emission indices for aircraft showed a strong dependence upon engine type. Our work also revealed differences from emission indices published in the emission data base of the International Civil Aviation Organisation. Among the VOC, reactive C₂–C₃ alkenes were found in significant amounts in the exhaust of an engine compared to ambient levels. Also, isoprene, a VOC commonly associated with biogenic emissions, was found in the exhaust, however it was not detected in refuelling emissions. The benzene to toluene ratio was used to discriminate exhaust from refuelling emission. In refuelling emissions, a ratio well below 1 was found, while for exhaust this ratio was usually about 1.7.