Effects of selected metal oxides on the dechlorination and destruction of PCDD and PCDF

OCDD and OCDF spiked silica/graphite based model fly ash containing various copper compounds and metal oxides were thermally treated under oxygen deficient conditions. All copper compounds tested showed a considerable dechlorination/hydrogenation reaction at 260 °C. After 30 min at 340 °C, less than 1% of the spiked OCDD and OCDF was recovered as T₄CDD/F to OCDD/F. Other compounds tested demonstrated a lower rate of dechlorination compared to the copper compounds. However, all other metal oxides showed a small dechlorination effect at 260 °C, which was considerably increased at 340 °C.

The model fly ash containing the different copper compounds or metal oxides showed comparable PCDD and PCDF isomer patterns after thermal treatment. However, small differences were observed among the different tested compounds. The PCDD and PCDF isomer patterns on the model fly ashes were similar to patterns found during dechlorination experiments on fly ashes from waste incineration processes.

Model fly ash containing Ca(OH)₂ exhibited the highest destruction potential, but a low dechlorination potential. In contrast, model fly ash containing any of the remaining compounds tested, was found to predominantly dechlorinate the spiked OCDD and OCDF.     

Thermal behavior of PCDD/PCDF in fly ash from municipal incinerators

The effect of thermal treatment of fly ash on the behaviour of PCDD/PCDF was studied in the range between 120 and 600° C. Annealing at 300° C (2 hrs) resulted in an increase of PCDD/PCDF concentration by a factor of 10 to 15. At 600° C degradation to concentrations below 0.1 ng/g is observed.     

Experimental and statistical determination of indicator parameters for the evaluation of fly ash and boiler ash PCDD/PCDF concentration from municipal solid waste incinerators

On-line detectable indicator parameters in the flue gas of municipal solid waste incinerators (MSWI) such as chlorinated benzenes (PCBz) are well known surrogate compounds for gas-phase PCDD/PCDF concentration. In the here presented work derivation of indicators is broadened to the detection of fly and boiler ash fractions with increased PCDD/PCDF content. Subsequently these fractions could be subject to further treatment such as recirculation in the combustion chamber to destroy their PCDD/PCDF and other organic pollutants' content. Aim of this work was to detect suitable on-line detectable indicator parameters in the gas phase, which are well correlated to PCDD/PCDF concentration in the solid residues. For this, solid residues and gas-phase samples were taken at three MSWI plants in Bavaria. Analysis of the ash content from different plants yielded a broad variation range of PCDD/PCDF concentrations especially after disturbed combustion conditions. Even during normal operation conditions significantly increased PCDD/PCDF concentrations may occur after unanticipated disturbances. Statistical evaluation of gas phase and ash measurements was carried out by means of principal component analysis, uni- and multivariate correlation analysis. Surprisingly, well known indicators for gas-phase PCDD/PCDF concentration such as polychlorinated benzenes and phenols proved to be insufficiently correlated to PCDD/PCDF content of the solid residues. Moreover, no single parameter alone was found appropriate to describe the PCDD/PCDF content of fly and boiler ashes. On the other hand, multivariate fitting of three or four parameters yielded convenient correlation coefficients of at least r=0.8 for every investigated case. Thereby, comprehension of plant operation parameters such as temperatures and air flow alongside concentrations of inorganic compounds in the gas phase (HCl, CO, SO2, NOx) gave the best results. However, the suitable set of parameters suited best for estimation of PCDD/PCDF concentration in solid residues has to be derived anew for each individual plant and type of ash.     

Dechlorination of polychlorinated biphenyls, dibenzo-p-dioxins and dibenzofurans on fly ash

Dechlorination of commercial mixtures of polychlorinated biphenyls (PCB) as well as polychlorinated dibenzo-p-dioxins (PCDD) and dibenzofurans (PCDF) on extracted and non-extracted fly ash obtained from municipal waste incinerator (MWI) was studied in closed systems under nitrogen atmosphere at temperatures of 260°C and 340°C. Decomposition results (given as the difference between PCB or PCDD/F molar amounts before and after the experiment (in %) due predominantly to dechlorination reactions) and detoxification data (expressed similarly but related to toxic PCB and PCDD/F congeners only and given in I-TEQ units) are reported. Detoxification of Delor 105/80T at 260°C and 340°C at a loading of 0.65 wt% was 99.48% and 100%, respectively. The decomposition of Delor 103 at 340°C and for the loading of 0.75 wt% corresponded to 99.99%. The detoxification capability of PCDD/Fs on extracted and non-extracted fly ash for loading of 130 and 264 ng/0.4 g of fly ash at 340°C made 96 and 98%, respectively.     

Quality control for sampling of PCDD/PCDF emissions from open combustion sources

Both long duration (>6 h) and high temperature (up to 139 °C) sampling efforts were conducted using ambient air sampling methods to determine if either high volume throughput or higher than ambient air sampling temperatures resulted in loss of target polychlorinated dibenzodioxins/dibenzofurans (PCDDs/PCDFs) from a polyurethane foam (PUF) sorbent. Emissions from open burning of simulated military forward operating base waste were sampled using EPA Method TO-9A for 185 min duration using a filter/PUF/PUF in series combination. After a 54 m³ sample was collected, the sampler was removed from the combustion source and the second PUF was replaced with a fresh, clean PUF. An additional 6 h of ambient air sampling (171 m³) was conducted and the second PUF was analyzed to determine if the PCDD/PCDF transferred from the filter and the first PUF. Less than 4.4% of the initial PCDD/PCDF was lost to the second PUF. To assess the potential for blow off of PCDD/PCDF analytes during open air sampling, the mobility of spiked mono- to hepta-PCDD/PCDF standards across a PUF sorbent was evaluated from ambient air temperatures to 145 °C with total volumes between 600 L and 2400 L. Lower molecular weight compounds and higher flow amounts increased release of the spiked standards consistent with vapor pressure values. At 600 L total sampled volume, the release temperature for 1% of the tetra-CDD (the lowest chlorinated homologue with a toxic compound) was 87 °C; increasing the volume fourfold reduced this temperature to 73 °C.     

Formation of artefacts while sampling emissions of PCDD/PCDF from open burning of biomass

Emission factors for PCDD/PCDF determined from open combustion are used to estimate national emission budgets; therefore, it is important to have confidence in their accuracy. It has been suspected that artefacts may form due to the presence of hot metal surfaces of sampling equipment, thus skewing emission factors. In this study, emissions of PCDD/PCDF from open burning of forest biomass over a brick hearth were sampled. Five experiments were carried out using a portable sampler. Experiments were designed where the key variable, sample hood and inlet temperatures were manipulated. Other variables such as fuel origin, type and density were consistent. The measured concentration of PCDD/PCDF in the smoke samples ranged from 0.01 μg TEQ (t fuel)⁻¹ at the lowest maximum hood temperature (185 °C) to 15 μg TEQ (t fuel)⁻¹ at the highest maximum hood temperature (598 °C). when hood inlet temperatures exceeded 400 °C emission factors were significantly elevated and this is attributed to the formation of artefacts that can cause the over estimation of emission factors. The increase in hood temperature also resulted in a change in the PCDD/PCDF congener and homologue profile of the emissions. For example at the lowest temperature (Fire 1) the PCDD/PCDF ratio measured was 50:1, whereas at the highest temperature (Fire 5) this ratio was about 0.53:1. When the sampler hood and inlet temperatures were kept in the normal operating range of <200 °C, emission factors were comparable to those observed in many previous studies in Australia with emissions dominated by PCDD.     

Effect of reaction time on PCDD and PCDF formation by de novo synthetic reactions under oxygen deficient and rich atmosphere

The effect of reaction time on formation of polychlorinated dibenzo-p-dioxins (PCDD) and dibenzofurans (PCDF) was studied under laboratory conditions in the system containing municipal waste incineration fly ash, activated carbon and copper chloride dihydrate at 300 degrees C in 99.999% N2 and N2 + 10% O2 atmosphere. The concentrations of tetra- to octa-chlorinated isomers as well as I-TEQ concentrations of toxic congeners are reported. The mechanism of PCDD and PCDF formation from chlorophenols and chlorinated biphenyls is discussed in the light of the time changes of PCDD/PCDF ratios.     

PCDD/F formation from oxy-PAH precursors in waste incinerator flyash

The yield of PCDD/F in relation to the presence of oxygenated PAH in model waste incinerator flyash has been investigated in a fixed bed laboratory scale reactor. Experiments were undertaken by thermal treatment of the model flyash at 250 and 350 °C under a simulated flue gas stream for 2 h. After reaction, the PCDD/F content of the reacted flyash and the PCDD/F released into the exhaust gas, and subsequently trapped by XAD-II resin in a down-stream condensation system were analyzed. The PAHs investigated were, dibenzofuran and benzo[b]naphtho[2,3-d]furan and were spiked onto the model flyash as reactant precursors for PCDD/F formation. The results showed significant formation of furans from both of the PAH investigated, however except from some highly chlorinated dioxin congeners, the formation of dioxins was not so common. Benzonaphthofuran was significantly more reactive than dibenzofuran in PCDD/F formation, in spite of the fact that dibenzofuran is structurally more similar to that of PCDD/F. Thus, there was no clear attribution between the chemical structure of PAH used and the formation of PCDD/F. There were considerable differences between the yields of PCDD/F congeners in the gaseous species and those in the reacted flyash under the same operational conditions. The concentration of PCDD/Fs was reduced at the higher reaction temperature of 350 °C; however, the higher temperature resulted in the majority of the PCDD/F formed on the flyash being released into the gas phase.     

Influence of temperature on PCDD/PCDF desorption from waste incineration flyash under nitrogen

A municipal solid waste incinerator flyash was heated to between 200 and 400 degrees C under nitrogen in a bench-scale, static bed reactor for 4 days soak time. The influence of temperature on the levels of PCDD and PCDF remaining in and desorbed from the ash were investigated using GC-MS/MS. PCDD and especially PCDF formation was seen on the flyash between 225 and 300 degrees C. Large increases in the I-TEQ of the treated ash relative to the increase in its overall PCDD/PCDF content indicated that the formation of 2378-substituted congeners was favoured over that of other substitution patterns. In the absence of a source of gaseous oxygen, formation was mainly attributed to de novo reactions involving solid phase oxygen. Dechlorination of the PCDD/PCDF in flyash became increasingly important above 275 degrees C. Maximum desorption was seen at 325 degrees C, with the equivalent of 35 wt% of the PCDD/F in the original flyash being recovered from the exhaust traps at this temperature. The desorbed species were mainly M(1)CDD/CDDF-T(3)CDD/CDDF resulting from dechlorination of higher chlorinated PCDD/PCDF, with consequently low I-TEQ values.     

Emissions of unintentional persistent organic pollutants from open burning of municipal solid waste from developing countries

Open burning of waste is the most significant source of polychlorinated dibenzo-para-dioxins and dibenzofurans (PCDD/PCDF) in many national inventories prepared pursuant to the Stockholm Convention on Persistent Organic Pollutants. This is particularly true for developing countries. Emission factors for POPs such as PCDD/PCDF, dioxin-like polychlorinated biphenyls (dl-PCB) and penta- and hexachlorobenzenes (PeCBz/HCB) from open burning of municipal solid waste in China and Mexico are reported herein. Six different waste sources were studied varying from urban-industrial to semi-urban to rural. For PCDD/PCDF, the emission factors to air ranged from 3.0 to 650 ng TEQ kg⁻¹ waste and for dl-PCB from 0.092 to 54 ng TEQ kg⁻¹ waste. Emission factors for PeCBz (17-1200 ng kg⁻¹ waste) and HCB (24-1300 ng kg⁻¹ waste) spanned a wide but similar range. Within the datasets there is no indication of significant waste composition effect on emission factor with the exception of significantly higher Mexico rural samples.     

Determination of polychlorinated dibenzo-p-dioxins and dibenzo-furans in solid residues from wood combustion by HRGC/HRMS

PCDD/PCDF were determined in solid samples from wood combustion. The samples included grate ashes, bottom ashes, furnace ashes as well as fly and cyclone ashes. The solid waste samples were classified into bottom and fly ash from native wood and bottom and fly ash from waste wood. For each of the four classes concentration distribution patterns from individual congeners, the sums of PCDD/PCDF and the international toxicity equivalents (I-TEQ) values are given. The I-TEQ levels of fly ash from waste wood burning can be approximately up to two thousand times higher than the values from fly ashes of natural wood. The I-TEQ levels in bottom ashes from waste wood combustion systems are as low as the corresponding ashes from the combustion of native wood. Grate ash samples from waste wood combustion systems with low carbon burnout show high levels of PCDD/PCDF.     

Formation of PCDD/Fs from oxidation of 2-monochlorophenol over an Fe2O3/silica surface

The role of iron in surface-mediated formation of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) from 2-chlorophenol (2-MCP) was investigated over the temperature range of 200-550 °C under oxidative conditions. In order to compare and contrast with previous work on copper and ferric oxide-mediated pyrolysis of 2-MCP, identical reaction conditions were maintained (50 ppm 2-MCP, model fly-ash particles containing 5% Fe₂O₃ on silica). Observed products included dibenzo-p-dioxin (DD), 1-monochlorodibenzo-p-dioxin (1-MCDD), dibenzofuran (DF), 4,6-dichlorodibenzofuran (4,6-DCDF), 2,4- and 2,6-dichlorophenol, 2,4,6-trichlorophenol, quinone, catechol, chloro-o-quinone, chlorocatechol and polychlorinated benzenes. Yields of DD and 1-MCDD were 2 and 5 times higher than under pyolysis conditions, respectively. Although 4,6-DCDF was the major PCDD/F product formed with a yield that was 2.5× greater than under pyrolysis, the yield of non-chlorinated DF, which was the dominant PCDD/F product under pyrolysis, decreased by a factor of 3. Furthermore, the ∼2× higher yield of PCDDs under oxidative conditions resulted in a PCDD to PCDF ratio of 0.75 compared to a relatively low ratio of 0.39 previously observed under pyrolytic conditions.     

A national inventory to estimate release of polychlorinated dibenzo-p-dioxins and dibenzofurans in Portugal

Taking into account current environmental concerns, the main objective of this work focused a national inventory aiming to estimate the amount of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/PCDF) released in Portugal in 2006. The methodology used was based on the Standardized Toolkit for Identification and Quantification of Dioxins and Furan Releases, developed by UNEP Chemicals, in 2005. The method allows the assessment of the amount of PCDD/PCDF released into the environment along five vectors involving air, water, land, products and residues. Facing some difficulties mainly regarding to the availability of data for some activities known to produce PCDD/PCDF, three scenarios (Sc1 to Sc3) corresponding to lower, central and upper estimates were established. The Sc1 scenario (lower estimate) includes the situations where in case of doubt or scarce information, reduced or none emission values were assumed, Sc2 refers to a central estimate, which is believed to be the most realistic for the Portuguese situation, while Sc3 corresponds to the worst case (upper estimate). The results obtained pointed out that the total amount of PCDD/PCDF emitted in Portugal during the period under analysis was in the range of 51.2-217.9 g TEQ year⁻¹, with the most likely value of 95.2 g TEQ year⁻¹ achieved under the Sc2 scenario. This study also showed that the methodology developed by UNEP Chemicals is a very simple one, and the main difficulty is the availability of data. The main indicators calculated in this study were 8.98 μg TEQ/(year person) by taking into account the total amount of PCDD/PCDF released, and 3.63 μg TEQ/(year person) when only air emissions were considered.     

Baseline soil levels of PCDD/Fs established prior to the construction of municipal solid waste incinerators in China

In order to determine the baseline contamination by polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) in different areas in China, prior to the construction of municipal solid waste incinerators (MSWIs), a total of 32 representative soil samples was collected near 16 incinerators and analyzed for their PCDD/F concentrations. The PCDD/F baseline concentrations in the soil samples ranged from 0.32 to 11.4 ng I-TEQ kg⁻¹ (dry matter), with average and median value of 2.73 and 2.24 ng I-TEQ kg⁻¹ (dry matter), respectively, and a span between maximum and minimum recorded value of 36. The PCDD homologues predominated in 26 out of 32 soil samples, with the ratio (PCDDs)/(PCDFs) ranging from 1.1 to 164; however in the other 6 samples, PCDF homologues were larger, with the same ratio varying from 0.04 to 0.8. Principal component analysis (PCA) and hierarchical cluster analysis (HCA) were used to examine PCDD/F amount and profile in these soil samples, and their possible associations with known emission sources: in this process 6 really distinct isomer fingerprints were identified. Background PCDD/F levels and profiles were comparable to those found in soils from China and other countries and indicate a rather low baseline PCDD/F contamination of soils. The present data provide the tools for future assessment of a possible impact of these MSWIs.     

Thermal removal of PCDD/Fs from medical waste incineration fly ash--effect of temperature and nitrogen flow rate

The fly ash used in this study was collected from a bag filter in a medical waste rotary kiln incineration system, using lime and activated carbon injection followed by their collection as mixed fly ash. Experiments were conducted on fly ash in a quartz tube, heated in a laboratory-scale horizontal tube furnace, in order to study the effect of temperature and nitrogen flow rate on the removal of PCDD/Fs. Results indicated that in this study PCDD/Fs in the fly ash mostly were removed and desorbed very little into the flue gas under thermal treatment especially when the heating temperature was higher than 350 °C, and dechlorination and destruction reactions took important part in the removal of PCDD/Fs. However, in terms of flow rate, when flow rate was higher than 4 cm s⁻¹, destruction efficiency of PCDD/Fs decreased dramatically and the main contributors were P₅CDF, H₆CDF and H₇CDF desorbed to flue gas, the PCDD/Fs in the fly ash decreased with enhanced flow rate.     

Accurate sampling of PCDD/F in high temperature flue-gas using cooled sampling probes

In a laboratory-scale combustion reactor, flue-gas samples were collected at two temperatures in the post-combustion zone, 700 °C and 400 °C, using two different water-cooled sampling probes. The probes were the cooled probe described in the European Standard method EN-1948:1, referred to as the original probe, and a modified probe that contained a salt/ice mixture to assist the cooling, referred to as the sub-zero probe. To determine the efficiency of the cooling probes, internal temperature measurements were recorded at 5 cm intervals inside the probes. Flue-gas samples were analyzed for polychlorinated dibenzo-p-dioxin and dibenzofurans (PCDD/Fs). Samples collected at 700 °C using the original cooling probe showed higher concentrations of PCDD/Fs compared to samples collected using the sub-zero probe. No significant differences were observed between samples collected at 400 °C. The results indicated that artifact formation of PCDD/Fs readily occurs during flue-gas sampling at high temperatures if the cooling within the probe is insufficient, as found for the original probe at 700 °C. It was also shown that this problem could be alleviated by using probes with an enhanced cooling capacity, such as the sub-zero probe.Although this may not affect samples collected for regulatory purposes in exit gases, it is of great importance for research conducted in the high-temperature region of the post-combustion zone.     

Dechlorination and destruction of PCDD,PCDF and PCB on selected fly ash from municipal waste incineration

The potential of fly ash to dechlorinate and destroy PCDD, PCDF and PCB was tested under oxygen deficient conditions in the laboratory. Specifically, two types of fly ash were compared, originating either from a fluidized bed incinerator using Ca(OH)₂ spray (FA1), or a stoker incinerator without Ca(OH)₂ impact (FA2).

Results from the present study indicate that on FA2 type fly ash, the degradation processes of OCDD, OCDF and D₁₀CB occurred primarily via dechlorination/hydrogenation up to temperature settings of 340 °C. In contrast, FA1 type fly ash was found to effect both dechlorination and destruction of these compounds already at temperature settings of 260 °C.

The dechlorination velocity of PCDD and PCDF did not differ significantly. However, the first dechlorination step of OCDF in the 1,9-position occurred faster compared to the first dechlorination step of OCDD.

The isomer pattern resulting from the dechlorination processes was quite similar on both FA1 and FA2, indicating that differences in alkalinity or elemental composition of the two types of fly ashes do not have a significant influence on the position of dechlorination. PCDD and PCDF dechlorination of the 2,3,7,8-positions was not favoured over dechlorination of the 1,4,6,9-positions on either type of fly ash. In contrast, dechlorination of PCB occurred predominantly on the toxicological relevant 3- and 4-positions.

The dechlorination/destruction processes were completed on both types of fly ash at 380 °C within one hour, which correlates well with results obtained from actual plant operation practices.     

The historical record of PCB and PCDD/F deposition at Greifensee, a lake of the Swiss plateau, between 1848 and 1999

Dated sediment cores provide an excellent way to investigate the historical input of persistent organic pollutants into the environment and to identify possible sources of pollution. The vertical distribution of polychlorinated dibenzo-p-dioxins/polychlorinated dibenzofurans (PCDD/F) and polychlorinated biphenyls (PCB) was investigated in a sediment core from Greifensee to elucidate the historical trends of PCDD/F and PCB inputs between 1848 and 1999. Concentrations of PCB and PCDD/F increased by more than one order of magnitude between 1930 and 1960. PCB and PCDD/F concentrations were 5700 ng/kg dry weight (dw) and 160 ng/kg dw, respectively, in sediments originating from the late 1930s and reached a maximum of 130,000 ng/kg dw and 2400 ng/kg dw, respectively, in the early 1960s. From 1960 on, concentrations decreased to the 1930s level by the mid 1980s. A remarkable shift in the PCDD/F pattern was observed after the early 1940s. Before 1940, the PCDD/F pattern was PCDF dominated (ratio of PCDD to PCDF=0.41+/-0.11), while the PCDD started to be the major species after the early 1940s (ratio of PCDD to PCDF=1.46+/-0.38). The temporal trends of PCB and PCDD/F correlate surprisingly well with each other. This might be due to the coincidence of two factors. The introduction of PCB on the market in the 1930s resulted in emissions due to the widespread use of these industrial chemicals. In the same time period, waste incineration became an increasingly popular way to get rid of garbage, boosting the PCDD/F emissions significantly. The rapid decline of PCDD/F and PCB concentrations in the sediment starting in the early 1960s reflects the result of better emission control techniques in thermal processes and the improvement of waste water treatment in the catchment of Greifensee.     

Dechlorination and destruction of PCDDs/PCDFs in fly ashes from municipal solid waste incinerators by low temperature thermal treatment

Dechlorination and destruction characteristics of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDDs/PCDFs) in fly ashes from commercial-scale municipal solid waste incinerators by low temperature thermal treatment using a laboratory-scale heating system were investigated. Experiments were carried out in reducing atmosphere at temperatures of 300 degrees C, 450 degrees C and 600 degrees C respectively, for the treatment time of 1h and 3h. Concentrations of PCDDs/PCDFs in raw fly ashes ranged from 35.5 to 107.3 microg kg(-1) (1.5-3.4 microg TEQ kg(-1)) and treated fly ashes ranged from 0.34 to 45.3 microg kg(-1) (0.012-1.63 microg TEQ kg(-1)). Concentrations of PCDDs/PCDFs in fly ashes treated at the different temperatures and times were observed to decrease with increase of treatment temperature and time by dechlorination or destruction. The distribution of octa- and hepta-chlorinated congeners were decreased and tetra-, penta- and hexa-chlorinated congeners were increased at 300 degrees C and 450 degrees C, but the distribution of octa- and hepta-chlorinated congeners were increased and tetra-, penta- and hexa-chlorinated congeners were again decreased at 600 degrees C. Total destruction efficiencies of PCDDs/PCDFs in fly ashes showed above 95% at the treatment temperature of 450 degrees C for 3h. However, removal efficiency of each congener in fly ashes varied, especially, 2,3,7,8-TeCDD and 1,2,3,7,8-PeCDD in fly ash A increased. And the dechlorination and destruction characteristics of PCDDs/PCDFs in fly ash A and B was different due to difference in contents of Ca-compounds and metal oxides such as CuO and PbO in fly ashes.     

Soil plate bioassay: an effective method to determine ecotoxicological risks

Levels of polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) were measured in the breast milk of mothers living in Giugliano (Campania, Italy), an area at increased risk of PCDD and PCDF exposure caused by recent and serious open-air waste-combustion accidents. Polychlorinated biphenyls (PCBs) in milk samples were also studied. Breast milk was also monitored in two cities in northern Italy, Milan and Piacenza, which were selected as controls. Other variables, such as diet and age of the mothers, were also studied. PCDD/F and PCB levels and congener profiles in breast-milk samples were similar in all these cities, though total PCDD/F and DL-PCB TEQs in samples from Giugliano were significantly lower than those in Milan and Piacenza (8.65 pg WHO-TEQ in Giugliano vs. 11.0 and 9.94 pg WHO-TEQ in Milan and Piacenza respectively). Thus no direct correlations were found between PCDD/F and PCB levels in breast milk and the suspected increased exposure through open-air waste combustion in Giugliano. Diet did not seem to affect PCDD/F and PCB levels, whereas a significant correlation was observed between the mother’s age and an increased concentration of PCDDs/Fs and PCBs in milk. Comparison of these findings with those of previous surveys in Italy in 2000-2001 showed a marked reduction of PCDD/F (about 60%) and DL-PCB (about 20%) levels in breast milk occurring over the last 10 years. This might well be a result of well functioning legislation, for example European Directives on of the reduction of the emission limits of PCDDs/Fs and PCBs from waste incineration set by EU Directive 2000/76/EC implemented in 2000, or Commission Regulations such as (EC) No. 466/2001 and 1881/2006 setting maximum levels for certain contaminants in foodstuffs.