Modelling phytoremediation by the hyperaccumulating fern, Pteris vittata, of soils historically contaminated with arsenic

Pteris vittata plants were grown on twenty-one UK soils contaminated with arsenic (As) from a wide range of natural and anthropogenic sources. Arsenic concentration was measured in fern fronds, soil and soil pore water collected with Rhizon samplers. Isotopically exchangeable soil arsenate was determined by equilibration with ⁷³As^V. Removal of As from the 21 soils by three sequential crops of P. vittata ranged between 0.1 and 13% of total soil As. Ferns grown on a soil subjected to long-term sewage sludge application showed reduced uptake of As because of high available phosphate concentrations. A combined solubility-uptake model was parameterised to enable prediction of phytoremediation success from estimates of soil As, ‘As-lability’ and soil pH. The model was used to demonstrate the remediation potential of P. vittata under different soil conditions and with contrasting assumptions regarding re-supply of the labile As pool from unavailable forms.     

水生植物修复氮、磷污染水体研究进展

氮、磷是引起水体富营养化、导致水质恶化的重要因素,因此去除氮、磷一直是污水处理的重要任务.鉴于传统物理、化学方法存在的操作难、成本高、易产生二次污染等问题,人们越来越多地将目光转向利用水生植物去除氮、磷营养物质、净化水质上.介绍了近年来国内外应用水生植物修复氮、磷污染水体的方法、效果及其影响因素,探讨了水生植物净化污染水体的机制.针对目前研究中的不足,提出今后应在不同植物种类开发、植物组合优化以及植物的净化机制等方面加强研究.     

Phytoremediation of arsenic contaminated paddy soils with Pteris vittata markedly reduces arsenic uptake by rice

Arsenic (As) accumulation in food crops such as rice is of major concern. To investigate whether phytoremediation can reduce As uptake by rice, the As hyperaccumulator Pteris vittata was grown in five contaminated paddy soils in a pot experiment. Over a 9-month period P. vittata removed 3.5-11.4% of the total soil As, and decreased phosphate-extractable As and soil pore water As by 11-38% and 18-77%, respectively. Rice grown following P. vittata had significantly lower As concentrations in straw and grain, being 17-82% and 22-58% of those in the control, respectively. Phytoremediation also resulted in significant changes in As speciation in rice grain by greatly decreasing the concentration of dimethylarsinic acid (DMA). In two soils the concentration of inorganic As in rice grain was decreased by 50-58%. The results demonstrate an effective stripping of bioavailable As from contaminated paddy soils thus reducing As uptake by rice.     

A fluorescence-based bioassay for aquatic macrophytes and its suitability for effect analysis of non-photosystem II inhibitors

Background, Goals and Scope During the last years the miniaturization of toxicity test systems for rapid and parallel measurements of large quantities of samples has often been discussed. For unicellular algae as well as for aquatic macrophytes, fluorescence-based miniaturized test systems have been introduced to analyze photosystem II (PSII) inhibitors. Nevertheless, high-throughput screening should also guarantee the effect detection of a broad range of toxicants in order to ensure routinely applicable, high-throughput measuring device experiments which can cover a broad range of toxicants and modes of action others than PSII inhibition. Thus, the aim of this study was to establish a fast and reproducible measuring system for non-PSII inhibitors for aquatic macrophyte species to overcome major limitations for use. Methods A newly developed imaging pulse-amplitude-modulated chlorophyll fluorometer (I-PAM) was applied as an effect detector in short-term bioassays with the aquatic macrophyte species Lemna minor. This multiwell-plate based measuring device enabled the incubation and measurement of up to 24 samples in parallel. The chemicals paraquat-dichloride, alizarine and triclosan were chosen as representatives for the toxicant groups of non-PSII herbicides, polycyclic aromatic hydrocarbons (PAHs) and pharmaceuticals and personal care products (PPCPs), which are often detected in the aquatic environment. The I-PAM was used (i) to establish and validate the sensitivity of the test system to the three non-PSII inhibitors, (ii) to compare the test systems with standardized and established biotests for aquatic macrophytes, and (iii) to define necessary time scales in aquatic macrophyte testing. For validation of the fluorescence-based assay, the standard growth test with L. minor (ISO/DIS 20079) was performed in parallel for each chemical. Results The results revealed that fluorescence-based measurements with the I-PAM allow rapid and parallel analysis of large amounts of aquatic macrophyte samples. The I-PAM enabled the recording of concentration-effect-curves with L. minor samples on a 24-well plate with single measurements. Fluorescence-based concentration-effect-curves could be detected for all three chemicals after only 1 h of incubation. After 4–5 h incubation time, the maximum inhibition of fluorescence showed an 80–100% effect for the chemicals tested. The EC50 after 24 h incubation were estimated to be 0.06 mg/L, 0.84 mg/L and 1.69 mg/L for paraquatdichloride, alizarine and triclosan, respectively. Discussion The results obtained with the I-PAM after 24 h for the herbicide paraquat-dichloride and the polycyclic aromatic hydrocarbon alizarine were in good accordance with median effective concentrations (EC50s) obtained by the standardized growth test for L. minor after 7 d incubation (0.09 mg/L and 0.79 mg/L for paraquat-dichloride and alizarine, respectively). Those results were in accordance with literature findings for the two chemicals. In contrast, fluorescence-based EC50 of the antimicrobial agent triclosan proved to be two orders of magnitude greater when compared to the standard growth test with 7 d incubation time (0.026 mg/L) as well as with literature findings. Conclusion Typically, aquatic macrophyte testing is very time consuming and relies on laborious experimental set-ups. The I-PAM measuring device enabled fast effect screening for the three chemicals tested. While established test systems for aquatic macrophytes need incubation times of ≥ 7 d, the I-PAM can detect inhibitory effects much earlier (24 h), even if inhibition of chemicals is not specifically associated with PSII. Thus, the fluorescence-based bioassay with the I-PAM offers a promising approach for the miniaturization and high-throughput testing of chemicals with aquatic macrophytes. For the chemical triclosan, however, the short-term effect prediction with the I-PAM has been shown to be less sensitive than with long-term bioassays, which might be due to physicochemical substance properties such as lipophilicity. Recommendations and Perspectives The results of this study show that the I-PAM represents a promising tool for decreasing the incubation times of aquatic macrophyte toxicity testing to about 24 h as a supplement to existing test batteries. The applicability of this I-PAM bioassay on emergent and submerged aquatic macrophyte species should be investigated in further studies. Regarding considerations that physicochemical properties of the tested substances might play an important role in microplate bioassays, the I-PAM bioassay should either be accompanied by evaluating physicochemical properties modeled from structural information prior to an experimental investigation, or by intensified chemical analyses to identify and determine nominal concentrations of the toxicants tested. The chemicals paraquat-dichloride, alizarine and triclosan were chosen as representatives for the toxicant groups of non-PSII herbicides, PAHs and PPCPs which are often detected in the aquatic environment. Nevertheless, in order to ensure a routinely applicable measuring device, experiments with a broader range of toxicants and samples of surface and/or waste waters are necessary. ESS-Submission Editor: Dr. Markus Hecker (MHecker@Entrix.com)     

漂浮植物塘处理农村分散生活污水的应用

通过现场实验评价了漂浮植物塘配合化粪池处理农村分散生活污水的效果。实验结果表明,漂浮植物有效地抑制了污染水体中藻类的生长;在平均水力停留时间为36 d,COD、TN、TP平均污染负荷分别为3.1、0.86和0.056 g/(m2.d)的条件下,大薸塘对COD、TN、TP的平均去除率分别为68.5%、89.9%和85.2%,出水COD、TN和TP平均浓度分别为47、4.15和0.40 mg/L,达到GB18918-2002中的一级A标准。在水乡地区利用漂浮植物与农村宅河构造漂浮植物处理系统,是一种深度处理化粪池出水、控制农村生活污水对河道造成污染的有效措施。     

Using phytoremediation technologies to upgrade waste water treatment in Europe

Goal, Scope and Background One of the burning problems of our industrial society is the high consumption of water and the high demand for clean drinking water. Numerous approaches have been taken to reduce water consumption, but in the long run it seems only possible to recycle waste water into high quality water. It seems timely to discuss alternative water remediation technologies that are fit for industrial as well as less developed countries to ensure a high quality of drinking water throughout Europe. Main Features The present paper discusses a range of phytoremediation technologies to be applied in a modular approach to integrate and improve the performance of existing wastewater treatment, especially towards the emerging micro pollutants, i.e. organic chemicals and pharmaceuticals. This topic is of global relevance for the EU. Results Existing technologies for waste water treatment do not sufficiently address increasing pollution situation, especially with the growing use of organic pollutants in the private household and health sector. Although some crude chemical approaches exist, such as advanced oxidation steps, most waste water treatment plants will not be able to adopt them. The same is true for membrane technologies. Discussion Incredible progress has been made during recent years, thus providing us with membranes of longevity and stability and, at the same time, high filtration capacity. However, these systems are expensive and delicate in operation, so that the majority of communities will not be able to afford them. Combinations of different phytoremediation technologies seem to be most promising to solve this burning problem. Conclusions To quantify the occurrence and the distribution of micropollutants, to evaluate their effects, and to prevent them from passing through wastewater collection and treatment systems into rivers, lakes and ground water bodies represents an urgent task for applied environmental sciences in the coming years. Recommendations Public acceptance of green technologies is generally higher than that of industrial processes. The EU should stimulate research to upgrade existing waste water treatment by implementing phytoremediation modules and demonstrating their reliability to the public.     

Removal processes for arsenic in constructed wetlands

Arsenic pollution in aquatic environments is a worldwide concern due to its toxicity and chronic effects on human health. This concern has generated increasing interest in the use of different treatment technologies to remove arsenic from contaminated water. Constructed wetlands are a cost-effective natural system successfully used for removing various pollutants, and they have shown capability for removing arsenic. This paper reviews current understanding of the removal processes for arsenic, discusses implications for treatment wetlands, and identifies critical knowledge gaps and areas worthy of future research. The reactivity of arsenic means that different arsenic species may be found in wetlands, influenced by vegetation, supporting medium and microorganisms. Despite the fact that sorption, precipitation and coprecipitation are the principal processes responsible for the removal of arsenic, bacteria can mediate these processes and can play a significant role under favourable environmental conditions. The most important factors affecting the speciation of arsenic are pH, alkalinity, temperature, dissolved oxygen, the presence of other chemical species - iron, sulphur, phosphate -, a source of carbon, and the wetland substrate. Studies of the microbial communities and the speciation of arsenic in the solid phase using advanced techniques could provide further insights on the removal of arsenic. Limited data and understanding of the interaction of the different processes involved in the removal of arsenic explain the rudimentary guidelines available for the design of wetlands systems.     

Electrokinetic-enhanced phytoremediation of soils: Status and opportunities

Phytoremediation is a sustainable process in which green plants are used for the removal or elimination of contaminants in soils. Both organic and inorganic contaminants can be removed or degraded by growing plants by several mechanisms, namely phytoaccumulation, phytostabilization, phytodegradation, rhizofiltration and rhizodegradation. Phytoremediation has several advantages: it can be applied in situ over large areas, the cost is low, and the soil does not undergo significant damages. However, the restoration of a contaminated site by phytoremediation requires a long treatment time since the remediation depends on the growth and the biological cycles of the plant. It is only applicable for shallow depths within the reach of the roots, and the remediation efficiency largely depends on the physico-chemical properties of the soil and the bioavailability of the contaminants. The combination of phytoremediation and electrokinetics has been proposed in an attempt to avoid, in part, the limitations of phytoremediation. Basically, the coupled phytoremediation–electrokinetic technology consists of the application of a low intensity electric field to the contaminated soil in the vicinity of growing plants. The electric field may enhance the removal of the contaminants by increasing the bioavailability of the contaminants. Variables that affect the coupled technology are: the use of AC or DC current, voltage level and mode of voltage application (continuous or periodic), soil pH evolution, and the addition of facilitating agents to enhance the mobility and bioavailability of the contaminants. Several technical and practical challenges still remain that must be overcome through future research for successful application of this coupled technology at actual field sites.     

Speciation and uptake of arsenic accumulated by corn seedlings using XAS and DRC-ICP-MS

ICP-MS was used to investigate the uptake of As(III) and As(V) from hydroponics growth media by corn seedlings. It was found that arsenic uptake by the plant roots for the arsenic(V) and arsenic(III) treatments were 95 and 112 ppm, respectively. However, in the shoots of the arsenic (V) treatments had 18 ppm whereas arsenic(III) treatments had 12 ppm. XANES studies showed that As for both treatments arsenic was present as a mixture of an As(III) sulfur complex and an As(V) oxygen complex. The XANES data was corroborated by the EXAFS studies showing the presence of both oxygen and sulfur ligands coordinated to the arsenic. Iron concentrations were found to increase by 4 fold in the As(V) contaminated growth media and 7 fold in the As(III) treatment compared to the control iron concentration of 500 ppm. Whereas, the total iron concentration in the shoots was found to decrease by approximately the same amount for both treatments from 360 ppm in the control to approximately 125 ppm in both arsenic treatments. Phosphorus concentrations were found to decrease in both the roots and shoots compared to the control plants. The total sulfur in the roots was found to increase in the arsenic(III) and arsenic(V) treatments to 560 ppm and 800 ppm, respectively, compared to the control plants 358 ppm. In addition, the total sulfur in shoots of the plants was found to remain relatively constant at approximately 1080 ppm. The potassium concentrations in the plants were found to increase in the roots and decrease in the shoots.     

Extraction of arsenic in a synthetic arsenic-contaminated soil using phosphate

An environment-friendly and cost-effective extraction method has been studied for the removal of arsenic from contaminated soil. A yellow-brown forest soil was contaminated with arsenic(V) and used as a model soil. Among various potassium and sodium salts, potassium phosphate was most effective in extracting arsenic, attaining more than 40% extraction in the pH range of 6–8 with minimum damage to the soil properties. Exchange mechanism is proposed for the extraction of arsenic from soil by phosphate. Sequential extraction shows that phosphate is effective in extracting arsenic of Al- and Fe-bound forms. Arsenic of residual form was not extracted. Arsenic was efficiently extracted by phosphate solution of pH 6.0 at 300 mM phosphate concentration and at 40°C.     

Phytoremediation of Atrazine by Poplar Trees: Toxicity,Uptake, and Transformation

Toxicity, uptake, and transformation of atrazine [2-chloro-4-(ethylamino)-6-(isopropylamino)-s-triazine] by three species of poplar tree were assessed. Poplar cuttings were grown in sealed flasks with hydrophonic solutions and exposed to various concentrations of atrazine for a period of two weeks. Toxicity effects were evaluated by monitoring transpiration and measuring poplar cutting mass. Exposure to higher atrazine concentrations resulted in decrease of biomass and transpiration accompanied by leaf chlorosis and abscission. However, poplar cuttings exposed to lower concentrations of atrazine grew well and transpired at a constant rate during experiment periods. Poplar cuttings could take up, hydrolyze, and dealkylate atrazine to less toxic metabolites. Metabolism of atrazine occurred in roots, stems, and leaves and became more complete with increased residence time in tissue. These results suggest that phytoremediation is a viable approach to removing atrazine from contaminated water and should be considered for other contaminants.     

Phytoextraction by arsenic hyperaccumulator Pteris vittata L. from six arsenic-contaminated soils: Repeated harvests and arsenic redistribution

This greenhouse experiment evaluated arsenic removal by Pteris vittata and its effects on arsenic redistribution in soils. P. vittata grew in six arsenic-contaminated soils and its fronds were harvested and analyzed for arsenic in October, 2003, April, 2004, and October, 2004. The soil arsenic was separated into five fractions via sequential extraction. The ferns grew well and took up arsenic from all soils. Fern biomass ranged from 24.8 to 33.5 g plant(-1) after 4 months of growth but was reduced in the subsequent harvests. The frond arsenic concentrations ranged from 66 to 6,151 mg kg(-1), 110 to 3,056 mg kg(-1), and 162 to 2,139 mg kg(-1) from the first, second and third harvest, respectively. P. vittata reduced soil arsenic by 6.4-13% after three harvests. Arsenic in the soils was primarily associated with amorphous hydrous oxides (40-59%), which contributed the most to arsenic taken up by P. vittata (45-72%). It is possible to use P. vittata to remediate arsenic-contaminated soils by repeatedly harvesting its fronds.     

Partitioning of arsenic in soil-crop systems irrigated using groundwater: a case study of rice paddy soils in southwestern Taiwan

The accumulation of As in rice due to groundwater irrigation in paddy fields represents a serious health hazard in South and Southeast Asia. In Taiwan, the fate of As in long-term irrigated paddy fields is poorly understood. Groundwater, surface soil, and rice samples were collected from a paddy field that was irrigated with As-containing groundwater in southwestern Taiwan. The purpose of this study is to elucidate the source and sink of As in the paddy field by comparing the As fractions in the soils that were obtained by a sequential extraction procedure (SEP) with the As uptake of rice. The risks associated with eating rice from the field can thus be better understood. The concentration of As in groundwater varied with time throughout the growing seasons of rice, but always exceeded the permitted maximum (10 μg L⁻¹) for drinking water by the WHO. The As concentration increased with the concentration of Fe in the groundwater, supporting the claim that a large amount of As was concentrated in the Fe flocs collected from the internal wall of the groundwater pump. The results of the SEP revealed that As bound with amorphous and crystalline hydrous oxides exhibited high availability in the soils. The root of rice accumulated the largest amount of As, followed by the straw, husk, and grain. Although the As concentration in the rice grain was less than 1.0 mg kg⁻¹, the estimated intake level was close to the maximum tolerable daily intake of As, as specified by the WHO.     

Geochemistry of high arsenic groundwater in Chia-Nan plain, Southwestern Taiwan: possible sources and reactive transport of arsenic

Major ion, trace element, and stable isotope analyses were performed on groundwater samples collected during November 2005 and 2006 in Chia-Nan plain of southwestern Taiwan to examine As mobilization in aquifers. The high concentrations of As, Fe and Mn in the groundwater is consistent with low Eh values (under moderately reduced state). Moreover, the observed Na/Cl and SO(4)/Cl molar ratios in groundwater demonstrate the influence of seawater intrusion. Seawater intrusion could provide required electron acceptors (i.e., SO(4)) for bacterial sulfate reduction and promote reducing conditions that are favorable for As mobilization. The concurrent increases in the concentrations of Fe and Mn from 2005 to 2006 may be caused by bacterial Fe(III) and Mn(IV) reduction. Geochemical modeling demonstrate that As(III) is the dominant As species and the presence of Fe-bearing carbonates, sulfides, and oxide phases may locally act as potential sinks for As. Mud volcano fluids were also collected and analyzed to assess the possible source of As in the Chia-Nan plain groundwater. The oxygen and hydrogen isotopic signatures indicate that the As-rich mud volcano fluids may have been modified by chemical exchange with (18)O-rich crustal rocks and possibly originated from mixing of deep brines with circulating meteoric water. Thus As in the Chia-Nan plain groundwater may have been evolved from deep crustal fluids or rock sources. The hydrogeochemistry and widespread As enrichment in groundwater of Chia-Nan plain result from multiple processes, e.g., de-watering of deep crustal fluids, seawater intrusion, and biogeochemical cycling of Fe, As, and S in alluvial sediments.     

Evaluation of effects of exposure time on aquatic toxicity with zooplanktons using a reduced life expectancy model

Traditionally in toxicological studies time is not studied as quantifiable variable but as a fixed endpoint. The Reduced Life Expectancy (RLE) model which relates exposure time and exposure concentration with lethal toxic effects was tested previously using fish data. In this current paper the effects of exposure time on aquatic toxicity with zooplanktons and various toxicants were evaluated using the RLE model based on ambient exposure concentration. The model was evaluated by plotting ln LT₅₀ against LC₅₀ using toxicity data with zooplanktons from the literature for metal, metalloid and organic compounds. Most of the experimental data sets can be satisfactorily correlated by use of the RLE model, but deviations occurred for some data sets. Those data sets were satisfactorily fitted by a two stage RLE model. This model was based on two phases: one in the peripheral system and other in the central system. Both the single and two stage RLE model support the hypothesis that toxicity is time dependent and decreases in a systematic way with increasing exposure time. A calculated normal life expectancy (NLT) can be obtained from the single stage model and is in accord with reported NLT but those obtained from the two stage RLE model are in excellent agreement.     

An approach for arsenic in a contaminated soil: Speciation, fractionation, extraction and effluent decontamination

The fractionation and speciation of As in a contaminated soil were investigated, and a remediation strategy was tested. Regarding speciation, we found that As(V) prevails over As(III) whereas more than 40% of total arsenic is in organic form. The fractionation of As was investigated with two sequential extraction methods: a low mobility was found. Then we tested the possibility of using phosphoric acid to extract As from the soil and cleaning the washing effluents by sorption onto montmorillonite. The efficiency of the extraction and of the adsorption onto the clay were also investigated for Cr, Cu, Fe, Mn, Ni, Pb and Zn, whose total concentrations and fractionation in the soil are reported here. The extraction percentages for As and metals ranged from 30 to 65%; the residual proportions in the soil are presumably in very unreactive forms. Montmorillonite showed a good uptake capacity towards the investigated pollutants.     

Reaction of arsenic vapor species with fly ash compounds: kinetics and speciation of the reaction with calcium silicates

In coal combustion systems, the partitioning of arsenic between the vapor and solid phases is determined by the interaction of arsenic vapors with fly ash compounds under post-combustion conditions. This partitioning is affected by gas–solid reactions between the calcium components of the ash particles and arsenic vapors. In this study, bench scale experiments were conducted with calcium compounds typical of coal-derived fly ash to determine product formation, the extent of reaction and reaction rates when contacted by arsenic oxide vapors. Experiments conducted with arsenic trioxide (As₄O_6(g)) vapors in contact with calcium oxide, di-calcium silicate and mono-calcium silicate over the temperature range 600–1000 °C indicated that these solids were capable of reacting with arsenic vapor species in both air and nitrogen. Calcium arsenate was the observed reaction product in all the samples analyzed. Maximum capture of arsenic occurred at 1000 °C with calcium oxide being the most effective of the three solids over the range of temperatures studied. Using a shrinking core model for a first order reaction and the results from intrinsic kinetic experiments conducted in air, the reaction rate constants were found to be 1.4×10⁻³exp(−2776/T) m/s for calcium oxide particles, 7.2×10⁻³exp(−3367/T) m/s for di-calcium silicate particles and 5.5×10⁻³exp(−3607/T) m/s for mono-calcium silicate particles. These results therefore suggest that any calcium present in fly ash can react with arsenic vapor and capture the metal in water-insoluble forms of the less hazardous As(V) oxidation state.     

The chemistry and behaviour of antimony in the soil environment with comparisons to arsenic: A critical review

This article provides a critical review of the environmental chemistry of inorganic antimony (Sb) in soils, comparing and contrasting findings with those of arsenic (As). Characteristics of the Sb soil system are reviewed, with an emphasis on speciation, sorption and phase associations, identifying differences between Sb and As behaviour. Knowledge gaps in environmentally relevant Sb data for soils are identified and discussed in terms of the limitations this imposes on understanding the fate, behaviour and risks associated with Sb in environmental soil systems, with particular reference to mobility and bioavailability.     

Assessing the genotoxic potentials of arsenic in tilapia (Oreochromis mossambicus) using alkaline comet assay and micronucleus test

This experiment was conducted to study the genotoxic potentials of sodium arsenite (NaAsO₂) in freshwater fish Oreochromis mossambicus by using alkaline comet assay and micronucleus (MN) test. Fish were exposed to three different concentrations (3 ppm, 28 ppm and 56 ppm) of arsenic and gill, liver and blood tissue samples were collected after 48 h, 96 h and 192 h of exposure. Arsenic exposure induced DNA damage in all tissues examined in a concentration dependent manner. A significant (p < 0.05) increase in the comet tail DNA (%) of the exposed fish liver, gill, and blood was observed after 48 h and 96 h of exposure, but a decline in DNA damage was recorded in all the tissues at all the three concentrations studied after 192 h of exposure. Liver tissue exhibited significantly (p < 0.05) higher DNA damage at all the concentrations examined, followed by gill and blood. Higher liver tail DNA (51.38 ± 0.21%) refers that it is more prone to injury to arsenic toxicity than the gill and blood. In blood samples arsenic induced micronucleus formation in a concentration dependent manner and highest (5.8 ± 0.46%) value was recorded in 56 ppm after 96 h of exposure, whereas, it was decreased after 192 h of exposure at all the three concentrations of NaAsO₂ examined which refers to the DNA repairing ability of fish to arsenic toxicity. The results of this study depict the genotoxic potentials of arsenic to fish which in turns provide insight on advanced study in aquatic toxicology.     

Inorganic arsenic speciation at river basin scales: The Tinto and Odiel Rivers in the Iberian Pyrite Belt, SW Spain

The Tinto and Odiel rivers are heavily affected by acid mine drainage from mining areas in the Iberian Pyrite Belt. In this work we have conducted a study along these rivers where surface water samples have been collected. Field measurements, total dissolved metals and Fe and inorganic As speciation analysis were performed. The average total concentration of As in the Tinto river (1975 μg L⁻¹) is larger than in the Odiel river (441 μg L⁻¹); however, the mean concentration of As(III) is almost four times higher in the Odiel. In wet seasons the mean pH levels of both rivers (2.4 and 3.2 for the Tinto and Odiel, respectively) increase slightly and the amount of dissolved total arsenic tend to decrease, while the As(III)/(V) ratio strongly increase. Besides, the concentration of the reduced As species increase along the water course. As a result, As(III)/(V) ratio can be up to 100 times higher in the lower part of the basins. An estimation of the As(III) load transported by both rivers into the Atlantic Ocean has been performed, resulting in about 60 kg yr⁻¹ and 2.7 t yr⁻¹ by the Tinto and Odiel rivers, respectively.