Comparison of inclined plate sedimentation and dissolved air flotation for the minimisation of subsequent nitrogenous disinfection by-product formation

The formation of disinfection by-products (DBPs), including both nitrogenous disinfection by-products (N-DBPs) and carbonaceous disinfection by-products (C-DBPs), was investigated upon chlorination of water samples following two treatment processes: (i) coagulation-inclined plate sedimentation (IPS)-filtration and (ii) coagulation-dissolved air flotation (DAF)-filtration. The removal of algae, dissolved organic nitrogen (DON), dissolved organic carbon (DOC) and UV₂₅₄ by coagulation-DAF-filtration was superior to coagulation-IPS-filtration. On average, 53%, 53% and 31% of DOC, DON and UV₂₅₄ were removed by coagulation-DAF-filtration process, which were higher than 47%, 31% and 27% of that by coagulation-IPS-filtration process. Additionally, coagulation-IPS-filtration performed less well at removing the low molecular weight organics than coagulation-DAF-filtration process. The concentrations of chloroform, dichloroacetamide (DCAcAm) and dichloroacetonitrile (DCAN) formed during chlorination after coagulation-DAF-filtration reached their maximum values of 13, 1.5 and 4.7 μg L⁻¹, respectively, and were lower than those after coagulation-IPS-filtration with the maximum detected levels of 17, 2.9 and 6.3 μg L⁻¹. However, the trichloronitromethane (TCNM) concentration after the two processes was similar, suggesting that DON may have less of a contribution to TCNM formation than DCAcAm and DCAN.     

Distribution of perfluorinated compounds in surface water from Hanjiang River in Wuhan,China

This study provided the first spatial distribution of perfluorinated compounds (PFCs) in Hanjiang River in Wuhan, China (HR). Surface water samples, collected from 23 sites in HR were analyzed for eight PFCs. The total concentrations of PFCs ranged from 8.90 to 568 ng L⁻¹, while perfluoropentanoic acid (PFOA, <LOQ − 256 ng L⁻¹) and perfluorooctane sulfonate (PFOS, <LOQ − 88.9 ng L⁻¹) dominated. All data were found to be normally distributed in the river. Similar spatial distribution tendencies were found among perfluorocarboxylates (PFCAs) and significant correlations were observed among PFCAs, while no significant correlations were found between PFOS and PFCAs. The distributions of PFCs were highly influenced by the industrial discharge and urban activities. The flux of PFCs from HR to the Yangtze River was estimated in the range of 16.9–127 kg yr⁻¹. More than a half of the samples studied could not meet the drinking water standards and avian wildlife values, suggesting further studies of characterizing PFCs and their potential risk to human were needed.     

Chlorination of chlortoluron: kinetics, pathways and chloroform formation

Chlortoluron chlorination is studied in the pH range of 3-10 at 25 ± 1 °C. The chlorination kinetics can be well described by a second-order kinetics model, first-order in chlorine and first-order in chlortoluron. The apparent rate constants were determined and found to be minimum at pH 6, maximum at pH 3 and medium at alkaline conditions. The rate constant of each predominant elementary reactions (i.e., the acid-catalyzed reaction of chlortoluron with HOCl, the reaction of chlortoluron with HOCl and the reaction of chlortoluron with OCl⁻) was calculated as 3.12 (± 0.10) × 10⁷ M⁻² h⁻¹, 3.11 (±0.39) × 10² M⁻¹ h⁻¹ and 3.06 (±0.47) × 10³ M⁻¹ h⁻¹, respectively. The main chlortoluron chlorination by-products were identified by gas chromatography-mass spectrometry (GC-MS) with purge-and-trap pretreatment, ultra-performance liquid chromatography-electrospray ionization-MS and GC-electron capture detector. Six volatile disinfection by-products were identified including chloroform (CF), dichloroacetonitrile, 1,1-dichloropropanone, 1,1,1-trichloropropanone, dichloronitromethane and trichloronitromethane. Degradation pathways of chlortoluron chlorination were then proposed. High concentrations of CF were generated during chlortoluron chlorination, with maximum CF yield at circumneutral pH range in solution.     

Ozonation as an advanced oxidant in treatment of bamboo industry wastewater

The present study employed ozonation process to treat the bamboo industry wastewater (BIWW). The impact of ozone dosage and initial organic concentration on color, COD and TOC removal rates were studied along with characterization of the major organics in raw and treated wastewater. The results suggested the ozone dosage of 3.15 g h⁻¹ (concentration 52.5 mg L⁻¹) was suitable for the treatment. After 25 min ozonation of 1 L raw wastewater, the color, COD and TOC removal efficiencies were 95%, 56% and 40%, respectively, with an influent COD concentration of 835 mg L⁻¹. The ratio of kg O₃ kg⁻¹ COD at 3.15 g h⁻¹ was 2.8 (<3), revealing that ozonation was a cost effective process for tertiary treatment of BIWW. Longer oxidization time was required to achieve similar results for raw wastewater with higher COD concentration. The chromatogram from gel permeation chromatography revealed that ozonation resulted in the breakdown of high molecular weight compounds into lower molecular weight components but could not completely mineralize the organic matter. The majority of these compounds were identified in both raw and ozonated samples via GC-MS analysis. In addition to ester derivatives as the main intermediates of ozonation, 1-chloroctadecane, methyl stearate, benzophenone and α-cyperone were identified as the by-products of ozonation.     

Removal and formation of chlorinated triclosan derivatives in wastewater treatment plants using chlorine and UV disinfection

Triclosan, a common antimicrobial agent, may react during the disinfection of wastewater with free chlorine to form three chlorinated triclosan derivatives (CTDs). This is of concern because the CTDs may be photochemically transformed to tri- and tetra-chlorinated dibenzo-p-dioxins when discharged into natural waters. In this study, wastewater influent, secondary (pre-disinfection) effluent, and final (post-disinfection) effluent samples were collected on two occasions each from two activated sludge wastewater treatment plants, one using chlorine disinfection and one using UV disinfection. Concentrations of triclosan and three CTDs were determined using ultra performance liquid chromatography-triple quadrupole mass spectrometry with isotope dilution methodology. Triclosan and the CTDs were detected in every influent sample at levels ranging from 453 to 4530 and 2 to 98 ng L⁻¹, respectively, though both were efficiently removed from the liquid phase during activated sludge treatment. Triclosan concentrations in the pre-disinfection effluent ranged from 36 to 212 ng L⁻¹, while CTD concentrations were below the limit of quantification (1 ng L⁻¹) for most samples. In the treatment plant that used chlorine disinfection, triclosan concentrations decreased while CTDs were formed during chlorination, as evidenced by CTD levels as high as 22 ng L⁻¹ in the final effluent. No CTDs were detected in the final effluent of the treatment plant that used UV disinfection. The total CTD concentration in the final effluent of the chlorinating treatment plant reached nearly one third of the triclosan concentration, demonstrating that the chlorine disinfection step played a substantial role in the fate of triclosan in this system.     

The effects of pH, bromide and nitrite on halonitromethane and trihalomethane formation from amino acids and amino sugars

In this study, the effects of pH, bromide and nitrite on the formation of halonitromethanes (HNMs) and trihalomethanes (THMs) from eight amino acids (glycine, alanine, serine, cysteine, aspartic acid, glutamic acid, lysine and histidine) and four amino sugars (glucosamine, galactosamine, N-acetylglucosamine and N-acetylneuraminic acid) were examined for chlorination and ozonation followed by chlorination. During ozonation-chlorination, two amino acids, glycine and lysine, exhibited distinctly higher HNM formation than the other compounds. The formation of HNMs was higher at pH 8 than 6. Glycine and lysine also produced higher levels of THMs than the other compounds at pH 8. The presence of nitrite resulted in an increase in HNM formation. The presence of bromide increased the HNM formation, especially brominated HNM species. Bromine incorporation factors of trihalogenated HNMs were higher than those of THMs. For chlorination alone, HNM levels were about the detection limit (4 nM or 0.7 μg L⁻¹) at pH 6 and 8, and in the presence of bromide or nitrite. Amino acids and amino sugars tested, except glycine and lysine, showed relatively low levels of THM (∼15 μg L⁻¹) formation.     

Evaluation of the presence of drugs of abuse in tap waters

A total of seventy samples of drinking water were tested for non-controlled and illicit drugs. Of these, 43 were from Spanish cities, 15 from seven other European countries, three from Japan and nine from seven different Latin American countries. The most frequently detected compounds were caffeine, nicotine, cotinine, cocaine and its metabolite benzoylecgonine, methadone and its metabolite EDDP. The mean concentrations of non-controlled drugs were: for caffeine 50 and 19 ng L⁻¹, in Spanish and worldwide drinking water respectively and for nicotine 13 and 19 ng L⁻¹. Illicit drugs were sparsely present and usually at ultratrace level (<1 ng L⁻¹). For example, cocaine has mean values of 0.4 (Spain) and 0.3 ng L⁻¹ (worldwide), whereas for benzoylecgonine, these mean values were 0.4 and 1.8 ng L⁻¹, respectively. Higher concentrations of benzoylecgonine were found in Latin American samples (up to 15 ng L⁻¹). No opiates were identified in any sample but the presence of methadone and EDDP was frequently detected. Total mean values for EDDP were 0.4 ng L⁻¹ (Spain) and 0.3 ng L⁻¹ (worldwide). Very few samples tested positive for amphetamines, in line with the reactivity of chlorine with these compounds. No cannabinoids, LSD, ketamine, fentanyl and PCP were detected.     

Influence of aggregated particles on biodegradation activities for dimethylarsinic acid (DMA) in Lake Kahokugata

Aquatic arsenic cycles mainly depend on microbial activities that change the arsenic chemical forms and influence human health and organism activities. The microbial aggregates degrading organic matter are significantly related to the turnover between inorganic arsenic and organoarsenic compounds. We investigated the effects of microbial aggregates on organoarsenic mineralization in Lake Kahokugata using lake water samples spiked with dimethylarsinic acid (DMA). The lake water samples converted 1 μmol L⁻¹ of DMA to inorganic arsenic for 28 d only under anaerobic and dark conditions in the presence of microbial activities. During the DMA mineralization process, organic aggregates >5.0 μm with bacterial colonization increased the densities. When the organic aggregates >5.0 μm were eliminated from the lake water samples using filters, the degradation activities were reduced. DMA in the lake water would be mineralized by the microbial aggregates under anaerobic and dark conditions. Moreover, DMA amendment enhanced the degradation activities in the lake water samples, which mineralized 50 μmol L⁻¹ of DMA. The DMA-amended aggregates >5.0 μm completely degraded 1 μmol L⁻¹ of DMA with a shorter incubation time of 7 d. The supplement of KNO₃ and NaHCO₃ to lake water samples also shortened the DMA-degradation period. Presumably, the bacterial aggregates involved in the chemical heterotrophic process would contribute to the DMA-biodegradation process in Lake Kahokugata, which is induced by the DMA amendment.     

Occurrence of veterinary antibiotics in animal wastewater and surface water around farms in Jiangsu Province, China

The objective of this investigation was to obtain a broad profile of veterinary antibiotics residues in animal wastewater and surface water around large-scale livestock and poultry farms in Jiangsu Province of China. Therefore, 53 samples collected from 27 large-scale animal farms in 11 cities and counties of Jiangsu Province in 2009, were monitored for 10 selected veterinary antibiotics using solid phase extraction and high performance liquid chromatography/electrospray ionization-tandem mass spectrometry (HPLC/ESI-MS/MS) techniques. Ten veterinary antibiotics were found in animal wastewaters, eight antibiotics were detected in pond waters, and animal farm-effluents and river water samples were contaminated by nine antibiotics. The most frequently detected antibiotics were sulfamethazine (75%), oxytetracycline (64%), tetracycline (60%), sulfadiazine (55%) and sulfamethoxazole (51%) which were detected with a maximum concentration of 211, 72.9, 10.3, 17.0 and 63.6 μg L⁻¹, respectively. The maximum concentration of 0.55 μg L⁻¹ for cyromazine, 3.67 μg L⁻¹ for chlortetracycline, 0.63 μg L⁻¹ for sulfadoxine, 39.5 μg L⁻¹ for doxycycline and 0.64 μg L⁻¹ for sulfaquinoxaline were determined in the collected samples. In general, the maximum concentration of the selected veterinary antibiotics was detected in animal wastewaters except for chlortetracycline in animal farm-effluents. In addition, residue levels of selected veterinary antibiotics in animal wastewater and surface water around the farms were related to animal species and have a high spatial variation.     

Development and calibration of a passive sampler for N-nitrosodimethylamine (NDMA) in water

N-Nitrosamines such as N-nitrosodimethylamine (NDMA) are organic compounds of environmental concern in groundwater, wastewater and potable water due to their potent carcinogenicity in laboratory animal studies and probable human carcinogenicity. While passive sampling techniques have become a widely used tool for providing time-averaged estimates of trace pollutant concentration, for chemicals such as NDMA that have relatively high water solubility, the selection of a suitable sorbent is difficult. This work is a proof of principle study that investigated for the first time the use of coconut charcoal as a passive sampler sorbent. Apparent charcoal/water sorption coefficients for NDMA were >551 mL g⁻¹ at environmentally relevant aqueous concentrations of less than 1 μg L⁻¹. Under the experimental conditions employed, a sampling rate of 0.45 L d⁻¹ was determined and for an aqueous concentration of 1000 ng L⁻¹, it is predicted that the sampler remains in the linear uptake stage for approximately 4 d, while equilibrium attainment would require about 26 d. The presence of humic acid, used as a surrogate for DOC, enhanced NDMA sorption on the coconut charcoal.     

Uranium in Kosovo’s drinking water

The results of this paper are an initiation to capture the drinking water and/or groundwater elemental situation in the youngest European country, Kosovo. We aim to present a clear picture of the natural uranium concentration in drinking water and/or groundwater as it is distributed to the population of Kosovo. Nine hundred and fifty-one (951) drinking water samples were analyzed by inductively coupled plasma mass spectrometry (ICPMS). The results are the first countrywide interpretation of the uranium concentration in drinking water and/or groundwater, directly following the Kosovo war of 1999. More than 98% of the samples had uranium concentrations above 0.01 μg L⁻¹, which was also our limit of quantification. Concentrations up to 166 μg L⁻¹ were found with a mean of 5 μg L⁻¹ and median 1.6 μg L⁻¹ were found. Two point six percent (2.6%) of the analyzed samples exceeded the World Health Organization maximum acceptable concentration of 30 μg L⁻¹, and 44.2% of the samples exceeded the 2 μg L⁻¹ German maximum acceptable concentrations recommended for infant food preparations.     

Stability considerations of aspartame in the direct analysis of artificial sweeteners in water samples using high-performance liquid chromatography-tandem mass spectrometry (HPLC-MS/MS)

A HPLC-MS/MS method is presented for the simultaneous determination of frequently used artificial sweeteners (ASs) and the main metabolite of aspartame (ASP), diketopiperazine (DKP), in environmental water samples using the direct-injection (DI) technique, thereby achieving limits of quantification (LOQ) of 10 ng L⁻¹. For a reliable quantification of ASP pH should be adjusted to 4.3 to prevent formation of the metabolite. Acesulfame (ACE), saccharin (SAC), cyclamate (CYC) and sucralose (SUC) were ubiquitously found in water samples. Highest concentrations up to 61 μg L⁻¹ of ACE were found in wastewater effluents, followed by surface water with concentrations up to 7 μg L⁻¹, lakes up to 600 ng L⁻¹ and groundwater and tap water up to 70 ng L⁻¹. The metabolite DKP was only detected in wastewater up to 200 ng L⁻¹ and at low detection frequencies.     

Influence of seasonal climate differences on the pharmaceutical,hormone and personal care product removal efficiency of a drinking water treatment plant

The potential presence of pharmaceuticals, hormones and personal care products in drinking water supplies has raised concerned over the efficiency with which these substances are removed by water treatment processes. In this work, we analyzed samples of raw, unprocessed water collected in different periods and found them to contain higher levels of these contaminants in the colder periods (viz. 12–314 ng L⁻¹ in autumn and winter as compared to 8–127 ng L⁻¹ in spring and summer) as a result of their biodegradation being favoured by high temperatures and solar irradiance. We also assessed the efficiency with which these contaminants are removed from drinking water by a water treatment plant operating in south-eastern Spain. Preoxidation with potassium permanganate and chloramination with sodium hypochlorite in the presence of highly concentrated ammonia were found to be the treatment steps most markedly contributing to the removal of pharmaceuticals, hormones and personal care products from drinking water (especially in the warmer periods, where these contaminants were completely removed from the water). By contrast, water treated in the colder periods (autumn and winter) still contained small amounts of ibuprofen and carbamazepine (0.09–0.5 ng L⁻¹) which, however, accounted for less than 0.2% of their original concentrations in the water prior to treatment.     

Contamination of nonylphenolic compounds in creek water, wastewater treatment plant effluents, and sediments from Lake Shihwa and vicinity, Korea: comparison with fecal pollution

Nonylphenolic compounds (NPs), coprostanol (COP), and cholestanol, major contaminants in industrial and domestic wastewaters, were analyzed in creek water, wastewater treatment plant (WWTP) effluent, and sediment samples from artificial Lake Shihwa and its vicinity, one of the most industrialized regions in Korea. We also determined mass discharge of NPs and COP, a fecal sterol, into the lake, to understand the linkage between discharge and sediment contamination. Total NP (the sum of nonylphenol, and nonylphenol mono- and di-ethoxylates) were 0.32-875 μg L⁻¹ in creeks, 0.61-87.0 μg L⁻¹ in WWTP effluents, and 29.3-230 μg g⁻¹ TOC in sediments. Concentrations of COP were 0.09-19.0 μg L⁻¹ in creeks, 0.11-44.0 μg L⁻¹ in WWTP effluents, and 2.51-438 μg g⁻¹ TOC in sediments. The spatial distributions of NPs in creeks and sediments from the inshore region were different from those of COP, suggesting that Lake Shihwa contamination patterns from industrial effluents differ from those from domestic effluents. The mass discharge from the combined outfall of the WWTPs, located in the offshore region, was 2.27 kg d⁻¹ for NPs and 1.00 kg d⁻¹ for COP, accounting for 91% and 95% of the total discharge into Lake Shihwa, respectively. The highest concentrations of NPs and COP in sediments were found in samples at sites near the submarine outfall of the WWTPs, indicating that the submarine outfall is an important point source of wastewater pollution in Lake Shihwa.     

Occurrence of glucocorticogenic activity in various surface waters in The Netherlands

Considering the important role that surface waters serve for drinking water production, it is important to know if these resources are under the impact of contaminants. Apart from environmental pollutants such as pesticides, compounds such as (xeno)estrogens have received al lot of research attention and several large monitoring campaigns have been carried out to assess estrogenic contamination in the aquatic environment. The introduction of novel in vitro bioassays enables researchers to study if – and to what extent – water bodies are under the impact of less-studied (synthetic) hormone active compounds. The aim of the present study was to carry out an assessment on the presence and extent of glucocorticogenic activity in Dutch surface waters that serve as sources for drinking water production. The results show glucocorticogenic activity in the range of <LOD – 2.4 ng dexamethasone equivalents L⁻¹ (dex EQs) in four out of eight surface waters. An exploratory time-series study to obtain a more complete picture of the yearly average of fluctuating glucocorticogenic activities at two sample locations demonstrated glucocorticogenic activities ranging between <LOD – 2.7 ng dex EQs L⁻¹. Although immediate human health effects are unlikely, the environmental presence of glucocorticogenic compounds in the ng L⁻¹ range compels further environmental research and assessment.     

Occurrence and source characterization of perfluorochemicals in an urban watershed

Perfluorochemicals (PFCs) are used in numerous applications, mainly as surfactants, and occur ubiquitously in the environment as complex mixtures. This study was undertaken to characterize the occurrence and sources of commonly detected PFC compounds in surface waters of the Marina catchment, a watershed that drains an urbanized section of Singapore. Of the 19 target PFCs, 13 were detected with perfluorooctanoic acid (PFOA) (5-31 ng L⁻¹) and perfluorooctane sulfonate (PFOS) (1-156 ng L⁻¹) being the dominant components. Other compounds detected included perfluoroalkyl carboxylates (C7-C12) and perfluoroalkyl sulfonates (C6 and C8). Sulfonamide compounds detected 2-(N-ethylperfluorooctanesulfonamido) acetic acid (N-EtFOSAA), 2-(N-methylperfluorooctanesulfonamido) acetic acid (N-MeFOSAA), perfluorooctanesulfonamido acetic acid (FOSAA) and perfluorooctanesulfonamide (FOSA) were putative transformation products of N-EtFOSE and N-MeFOSE, the N-ethylated and N-methylated ethyl alcohol derivatives, respectively. Surface water concentrations were generally higher during dry weather than during storm water flow: the median concentrations of total PFCs in dry and wet weather were 57 and 138 ng L⁻¹ compared to 42 and 79 ng L⁻¹, respectively, at Stamford and Alexandra canal, suggesting the presence of a continuous source(s) which is subject to dilution during storm events. In rain water, median concentrations were 6.4 ng L⁻¹, suggesting rain contributed from 12-25% to the total PFC load for non-point source sites. The longitudinal concentration profile along one of the canals revealed a point source of sulfonated PFCs (PFOS), believed to originate from aqueous film-forming foam (AFFF). Sources were characterized using principal component analysis (PCA) and by plotting PFHxS/PFOA against PFOS/PFOA. Typical surface waters exhibit PFOS/PFOA and PFHxS/PFOA ratios below 0.9 and 0.5, respectively. PCA plots reveal waters impacted by “non-typical” PFC sources in Alexandra canal.     

Derivation of predicted no effect concentrations (PNEC) for 2,4,6-trichlorophenol based on Chinese resident species

2,4,6-Trichlorophenol (2,4,6-TCP) is a common chemical intermediate and a by-product of water chlorination and combustion processes, and is a priority pollutant of the aquatic environment in many countries. Although information on the toxicity of 2,4,6-TCP is available, there is a lack of information on the predicted no-effect concentration (PNEC) of 2,4,6-TCP, mainly due to the shortage of chronic and site-specific toxicity data. In the present study, acute and sub-chronic toxicity of 2,4,6-TCP on six different resident Chinese aquatic species were determined. PNEC values were calculated and compared by use of two approaches: assessment factor (AF) and species sensitivity distribution (SSD). Values for acute toxicity ranged from 1.1 mg L⁻¹ (Plagiognathops microlepis) to 42 mg L⁻¹ (Corbicula fluminea) and the sub-chronic no observed effect concentrations (NOECs) ranged from 0.05 mg L⁻¹ (Mylopharyngodon piceus) to 2.0 mg L⁻¹ (C. fluminea). PNECs obtained by the assessment factor approach with acute (AF = 1000, 0.001 mg L⁻¹) or chronic (AF = 10, 0.005 mg L⁻¹) toxicity data were one order of magnitude less than those from SSD methods (0.057 mg L⁻¹). PNEC values calculated using SSD methods with a 50% certainty for 2,4,6-TCP was less than those obtained by use of the USEPA recommend final chronic value (FCV) method (0.097 mg L⁻¹) and the one obtained by use of the USEPA recommend acute-to-chronic (ACR) methods (0.073 mg L⁻¹). PNECs derived using AF methods were more protective and conservative than that derived using SSD methods.     

Highly organic natural media as permeable reactive barriers: TCE partitioning and anaerobic degradation profile in eucalyptus mulch and compost

The occurrence, removal efficiency and seasonal variation of 22 antibiotics, including eight fluoroquinolones, nine sulfonamides and five macrolides, were investigated in eight sewage treatment plants (STPs) in Beijing, China. A total of 14 antibiotics were detected in wastewater samples, with the maximum concentration being 3.1 μg L⁻¹ in the influent samples and 1.2 μg L⁻¹ in the effluent samples. The most frequently detected antibiotics were ofloxacin, norfloxacin, sulfadiazine, sulfamethoxazole, erythromycin and roxithromycin; of these, the concentration of ofloxacin was the highest in most of the influent and effluent samples. Eighteen antibiotics were detected in the sludge samples, with concentrations ranging from 1.0 × 10⁻¹ to 2.1 × 10⁴ μg kg⁻¹. The dominant antibiotics found in the sludge samples were the fluoroquinolones, with ofloxacin having the highest concentration in all the sludge samples. The antibiotics could not be removed completely by the STPs, and the mean removal efficiency ranged from −34 to 72%. Of all the antibiotics, the fluoroquinolones were removed comparatively more efficiently, probably due to their adsorption to sludge. Seasonal variation of the antibiotics in the sludge samples was also studied. The concentrations of antibiotics in winter were higher than in spring and autumn. Since the total levels of the fluoroquinolones detected in the influent samples were lower than the predicted no-effect concentration (PNEC) of 8.0 μg L⁻¹, the residues of these antibiotics would be unlikely to have adverse effects on microorganisms involved in sewage treatment processes.     

Risk assessment of xenoestrogens in a typical domestic sewage-holding lake in China

Release of domestic sewage leads to accumulation of xenoestrogens in holding waters, especially in closed or semi-enclosed waters such as lakes. In the study, the occurrence, distribution, estrogenic activity and risk of eight xenoestreogens were evaluated in Lake Donghu, China. Nonylphenol (NP), octylphenol (OP), and bisphenol A (BPA) were identified as the main xenoestrogens ranging from tens of ng L⁻¹ (in the surface water) or ng g⁻¹ dw (in the suspended particles and sediment) to tens of μg L⁻¹ or μg g⁻¹ dw. The sum of 17β-estradiol equivalents (∑EEQs) ranged from 0.32 to 45.02 ng L⁻¹ in the surface water, 0.53 to 71.86 ng g⁻¹ dw in the suspended particles, and 0.09 to 24.73 ng g⁻¹ dw in the sediment. Diethylstilbestrol (DES) was determined as the main contributor to ∑EEQs followed by NP. The risk assessment showed a higher risk in the surface water than in the suspended particles and sediment in such domestic sewage-holding lake.