Effect of lipids on sorption/desorption hysteresis in natural organic matter

The chemical composition and physical conformation of natural organic matter (NOM) play a major role in regulating its capacity to retain hydrophobic organic compounds. Naphthalene and phenanthrene were used to study the correlations between sorption/desorption isotherm nonlinearity and compositional data obtained from quantitative ¹³C solid-state DPMAS NMR spectroscopy for soil and peat organic matter with or without lipids. Sorption experiments were conducted using a batch equilibration method. Desorption experiments were carried out immediately following the sorption experiments by three successive decant-refill cycles. Hysteresis was observed in all samples. Nonlinear sorption behavior was increased by removal of lipids from the NOM. The hysteresis index, obtained from the ratio of the Freundlich exponents (N values) for the desorption and sorption isotherms, was lower in the lipid-extracted NOM samples than in the same samples without lipid extraction. The relationship between the extent of hysteresis and the characteristics of the ¹³C DPMAS NMR spectra indicates that altering NOM composition through lipid extraction not only increased the proportion of aromatic-C content, but also increased sorption/desorption hysteresis. Our data also suggest that the hysteresis index is negatively related to aromaticity.     

Long-term tillage effects on soil metolachlor sorption and desorption behavior

Sorption and desorption are two important processes that influence the amount of pesticides retained by soils. However, the detailed sorption mechanisms as influenced by soil tillage management are unclear. This study examined the sorption and desorption characteristics of metolachlor [2-chloro-N-(2-ethyl-6-methyphenyl)-N-(2-methoxy-1-methylethyl)-acetamide] using the soil samples collected from the long-term conservation tillage (CnT) and conventional tillage (CT) research plots established in 1979 in Darlinton, SC. Humic acid (HA) and humin were extracted from the soils and used in the sorption experiments along with the whole soil samples. The sorption experiments were conducted using a batch-equilibration method. Three sequential desorption rinses were carried out following the sorption experiments. By comparing metolachlor sorption and desorption results we observed hysteresis for all soil samples and their organic matter fractions. Sorption nonlinearity (N) and hysteresis were dependent on the structure and composition of soil organic matter (SOM), e.g., Freundlich isotherm exponents (N) of HA and humin from CnT were higher than those of CT treatment, which may be related to high aromaticity of SOM fractions in CT treatment. Sorption capacity (K'f) was positively correlated with soil organic carbon (SOC) content. These results show that long-term tillage management can greatly affect metolachlor sorption and desorption behavior probably by qualitative differences in the structural characteristics of the humic substances.     

Investigations on the sorption of a toxaphene model congener, the B7-1450, on marine sediments

Sorption is a natural process that takes place in sediments or soils and changes the mobility and availability of hydrophobic organic compounds, such as toxaphene pesticide in the environment. The sorption of the 2-exo,3-endo,5-exo,8,9,10,10-heptachlorobornane (B7-1450), used as a model compound of the toxaphene heptachlorobornane congeners found in sediments, was investigated for the first time through a series of batch sorption experiments. The losses of B7-1450 due to adsorption onto glass walls and to evaporation occurring during analytical treatment steps were corrected. The study showed that these specific losses ranged from 2% to 3.5% for the glass walls adsorption and can be as high as 15% for the evaporation treatment. The sorption coefficients, K(d) and K(oc), of B7-1450 could be overestimated by >30%, particularly for low-concentration samples, if the losses were not corrected. Loss correction equations were established, validated and applied to determine sorption coefficients for the B7-1450 congener. The K(oc) values for B7-1450 determined over a gradient of concentrations ranged from 3.5x10(4) to 6.5x10(4)mlg(-1), revealing a strong affinity of B7-1450 for marine sediments.     

Sorption-desorption of cadmium in aqueous palygorskite, sepiolite, and calcite suspensions: isotherm hysteresis

Sorption isotherms have been widely used to assess the heavy metal retention characteristics of soil particles. Desorption behavior of the retained metals, however, usually differ from that of sorption, leading to a lack of coincidence in the experimentally obtained sorption and desorption isotherms. In this study, we examine the nonsingularity of cadmium (Cd) sorption–desorption isotherms, to check the possible hysteresis and reversibility phenomena, in aqueous palygorskite, sepiolite and calcite systems. Sorption of Cd was carried out using a 24-h batch equilibration experiment with eight different Cd solution concentrations, equivalent to 20–100% of maximum sorption capacity of each mineral. Immediately after sorption, desorption took place using successive dilution method with five consecutive desorption steps. Both Cd sorption and desorption data were adequately described by Freundlich equation (0.81 < r² < 0.99). The sorption and desorption reactions, however, did not provide the same isotherms, indicating that hysteresis occurred in Cd sorption–desorption processes. The extent of hysteresis was quantified based on the differences obtained from sorption and desorption isotherms regarding the amount of Cd sorbed, the Freundlich exponent, and the Cd distribution coefficient. The results revealed that, sepiolite possessed the most hysteretic behavior among the minerals studied. Calcite showed much smaller hysteresis compared to the other two silicate clays at low Cd surface load, but its hysteresis indices significantly increased, and exceeded that of palygorskite, as the amount of Cd in the systems increased. The average amount of Cd released after five desorption steps, was 13.8%, 2.2% and 3.6% for the palygorskite, sepiolite and calcite, respectively, indicating that a large portion of Cd was irreversibly retained by the minerals.     

Enhancement of chlorophenol sorption on soil by geophagous earthworms (Metaphire guillelmi)

Earthworms are the dominant soil biomass of many terrestrial ecosystems and markedly influence the physico-chemical and biological properties of soil; however, little is known about the effects of earthworm activities on the environmental behavior of micropollutants in soil. We studied the sorption and desorption of 2,4-dichlorophenol, 2,4,6-trichlorophenol, and pentachlorophenol on geophagous earthworm (anecic Metaphire guillelmi) casts of various aging times and on the parent soil. The casts were characteristic of lower pH and higher content of fine particles (silt and clay) than the parent soil. The sorption of the chlorophenols on the soil and casts were well fitted to linear isotherms, with sorption capacity in the order of pentachlorophenol > 2,4-dichlorophenol > 2,4,6-trichlorophenol. The sorption on the cast with different aging time was quite similar and was higher than on the parent soil. The sorption on the soil did not change between pH 7.07 of the soil and pH 6.76 of the casts. The desorption hysteresis of the chlorophenols on the soil and casts was compound specific and 2,4,6-trichlorophenol showed the highest hysteresis. The higher sorption capacity of the casts was not owing to the lowered pH of the casts, but mainly to the higher fine particles in the casts and the possible changes of nature of the soil organic matter through the earthworm gut passage. Our results indicate that geophagous earthworms may change sorption behavior and thus the bioavailability and transport of chlorophenols in soil. Earthworm effects should be considered when evaluating the environmental behavior and risk of organic pollutants in the ecosystems where earthworms are abundant.     

Sorption-desorption behaviour of 2,4-dichlorophenol by marine sediments

Batch kinetic and isotherm experiments were conducted to determine the sorption-desorption behavior of 2,4-dichlorophenol from seawater solutions by marine sediments containing various amounts of organic carbon (from 1.02% to 12.72% dry weight). The results indicated linear type isotherms for sorption and desorption in all marine sediments studied. The observed difference in linear sorption coefficients between sorption and desorption was indicative of sorption hysteresis. The kinetic experiments showed that equilibrium was established in less than 20 h. The study is significant with respect to sediment remediation in contaminated harbors and coastal areas.     

Cosolvent effects on sorption isotherm linearity

Sorption-desorption hysteresis, slow desorption kinetics, and other nonideal phenomena have been attributed to the differing sorptive characteristics of the natural organic polymers associated with soils and sediments. In this study, aqueous and mixed solvent systems were used to investigate the effects of a cosolvent, methanol, on sorption isotherm linearity with natural organic matter (NOM), and to evaluate whether these results support, or weaken, the rubbery/glassy polymer conceptualization of NOM. All of the sorption isotherms displayed some nonlinear character. Our data indicates that all of the phenanthrene and atrazine isotherms were nonlinear up to the highest equilibrium solution concentration to solute solubility in water or cosolvent ratios (Ce/Sw,c) used, approximately 0.018 and 0.070, respectively. Isotherm linearity was also observed to increase with volumetric methanol content (fc). This observation is consistent with the NOM rubbery/glassy polymer conceptualization: the presence of methanol in NOM increased isotherm linearity as do solvents in synthetic polymers, and suggests that methanol is interacting with the NOM, enhancing its homogeneity as a sorptive phase so that sorption is less bimodal as fc increases. When the equilibrium solution concentration was normalized for solute solubility in water or methanol-water solutions, greater relative sorption magnitude was observed for the methanol-water treatments. This observation, in conjunction with the faster sorption kinetics observed in the methanol-water sediment column systems, indicates that the increase in relative sorption magnitude with fc may be attributed to the faster sorption kinetics in the methanol-water systems, and hence, greater relative sorptive uptake for the rubbery polymer fraction of NOM at similar time scales.     

Washing of marine coastal sand in a batch reactor: sorption and desorption of BTEX

This study addresses the issues related to decontamination of marine beach sand accidentally contaminated by petroleum products. Sorption and desorption of BTEX (i.e., benzene, toluene, ethylbenzene, and xylene) onto the sand from Uran Beach, located near the city of Mumbai, India, were studied, and isotherms were determined using the bottle point method to estimate sorption coefficients. Alternatively, QSARs (i.e., quantitative structure activity relationships) were developed and used to estimate the sorption coefficients. Experiments for kinetics of volatilization as well as for kinetics of sorption and desorption in the presence of volatilization were conducted in a fabricated laboratory batch reactor. A mathematical model describing the fate of volatile hydrophobic organic pollutants like BTEX (via sorption and desorption in presence of volatilization) in a batch sediment-washing reactor was proposed. The experimental kinetic data were compared with the values predicted using the proposed models for sorption and desorption, and the optimum values of overall mass transfer coefficients for sorption (K(s)a(s)) and desorption (K(d)a(d)) were estimated. This was achieved by minimization of errors while using the sorption coefficients (Kp) obtained from either laboratory isotherm studies or the QSARs developed in the present study. Independent experimental data were also collected and used for calibration of the model for volatilization, and the values of the overall mass transfer coefficient for volatilization (K(g)a(g)) were estimated for BTEX. In these exercises of minimization of errors, comparable cumulative errors were obtained from the use of Kp values derived from experimental isotherms and QSARs.     

The impact of contact time on pyrene sorptive behavior by a sandy-loam soil

Batch experiments with pyrene (PYR) were conducted to quantify the effect of contact time on its sorption and desorption behavior by a sandy-loam soil. Twenty-four and 48 h contact times were chosen for the nonequilibrium conditions and 240 h for the pseudoequilibrium study. All times was selected based on the kinetic results. The nonlinear, pseudoequilibrium sorption isotherm was fit to a two-stage Freundlich model: 3-7 mg/l for the first stage and 7-15 mg/l for the second stage. A substantial fraction of the sorbed PYR was not desorbed within the given desorption time. The reason of hysteresis was found to be a sorption enhancement due to soil hydration which provided more sorption sites. A desorption enhancement at 240-h desorption steps was attributed to the increased dissolved organic matter evolution. This study also found that both soil organic matter and clay materials had an equal role in PYR sorption enhancement and desorption resistance.     

A mass transfer model for simulating VOC sorption on building materials

The sorption of volatile organic compounds (VOCs) by different building materials can significantly affect VOC concentrations in indoor environments. In this paper, a new model has been developed for simulating VOC sorption and desorption rates of homogeneous building materials with constant diffusion coefficients and material–air partition coefficients. The model analytically solves the VOC sorption rate at the material–air interface. It can be used as a “wall function” in combination with more complex gas-phase models that account for non-uniform mixing to predict sorption process. It can also be used in conjunction with broader indoor air quality studies to simulate VOC exposure in buildings.     

Impact of long-term wastewater irrigation on sorption and transport of atrazine in Mexican agricultural soils

In the Mezquital Valley, Mexico, crops have been irrigated with untreated municipal wastewater for more than a century. Atrazine has been applied to maize and alfalfa grown in the area for weed control for 15 years. Our objectives were to analyse (i) how wastewater irrigation affects the filtering of atrazine, and (ii) if the length of irrigation has a significant impact. We compared atrazine sorption to Phaeozems that have been irrigated with raw wastewater for 35 (P35) and 85 (P85) years with sorption to a non-irrigated (P0) Phaeozem soil under rainfed agriculture. The use of bromide as an inert water tracer in column experiments and the subsequent analysis of the tracers’ breakthrough curves allowed the calibration of the hydrodynamic parameters of a two-site non equilibrium convection-dispersion model. The quality of the irrigation water significantly altered the soils’ hydrodynamic properties (hydraulic conductivity, dispersivity and the size of pores that are hydraulically active). The impacts on soil chemical properties (total organic carbon content and pH) were not significant, while the sodium adsorption ratio was significantly increased. Sorption and desorption isotherms, determined in batch and column experiments, showed enhanced atrazine sorption and reduced and slower desorption in wastewater-irrigated soils. These effects increased with the length of irrigation. The intensified sorption-desorption hysteresis in wastewater-irrigated soils indicated that the soil organic matter developed in these soils had fewer high-energy, easily accessible sorption sites available, leading to lower and slower atrazine desorption rates. This study leads to the conclusion that wastewater irrigation decreases atrazine mobility in the Mezquital valley Phaeozems by decreasing the hydraulic conductivity and increasing the soil's sorption capacity.     

Impact of long-term wastewater irrigation on sorption and transport of atrazine in Mexican agricultural soils

In the Mezquital Valley, Mexico, crops have been irrigated with untreated municipal wastewater for more than a century. Atrazine has been applied to maize and alfalfa grown in the area for weed control for 15 years. Our objectives were to analyse (i) how wastewater irrigation affects the filtering of atrazine, and (ii) if the length of irrigation has a significant impact. We compared atrazine sorption to Phaeozems that have been irrigated with raw wastewater for 35 (P35) and 85 (P85) years with sorption to a non-irrigated (P0) Phaeozem soil under rainfed agriculture. The use of bromide as an inert water tracer in column experiments and the subsequent analysis of the tracers' breakthrough curves allowed the calibration of the hydrodynamic parameters of a two-site non equilibrium convection-dispersion model. The quality of the irrigation water significantly altered the soils' hydrodynamic properties (hydraulic conductivity, dispersivity and the size of pores that are hydraulically active). The impacts on soil chemical properties (total organic carbon content and pH) were not significant, while the sodium adsorption ratio was significantly increased. Sorption and desorption isotherms, determined in batch and column experiments, showed enhanced atrazine sorption and reduced and slower desorption in wastewater-irrigated soils. These effects increased with the length of irrigation. The intensified sorption-desorption hysteresis in wastewater-irrigated soils indicated that the soil organic matter developed in these soils had fewer high-energy, easily accessible sorption sites available, leading to lower and slower atrazine desorption rates. This study leads to the conclusion that wastewater irrigation decreases atrazine mobility in the Mezquital valley Phaeozems by decreasing the hydraulic conductivity and increasing the soil's sorption capacity.     

Effect of salinity and sediment characteristics on the sorption and desorption of perfluorooctane sulfonate at sediment-water interface

This study investigated the influence of solution salinity, pH and the sediment characteristics on the sorption and desorption of perfluorooctane sulfonate (PFOS). The results showed that the sorption of PFOS onto sediment increased by a factor of 3 as the CaCl₂ concentration increased from 0.005 to 0.5 mol L⁻¹ at pH 7.0, and nearly 6 at pH 8.0. Desorption hysteresis occurred over all salinity. The thermodynamic index of irreversibility (TII) values increased with increasing concentration of CaCl₂. Maximum irreversibility was found in the sorption systems with CaCl₂ in the concentration of 0.5 mol L⁻¹. The results suggested that PFOS can be largely removed from the water with increasing salinity, and get trapped onto sediments irreversibly. These phenomena could be explained by salting-out effect and Ca-bridging effect. Studies also suggested that the content of total organic carbon is the dominant psychochemical properties of sediment controlling the sorption of PFOS.     

Transport of polar and non-polar volatile compounds in polystyrene foam and oriented strand board

Transport of hexanal and styrene in polystyrene foam (PSF) and oriented strand board (OSB) was characterized. A microbalance was used to measure sorption/desorption kinetics and equilibrium data. While styrene transport in PSF can be described by Fickian diffusion with a symmetrical and reversible sorption/desorption process, hexanal transport in both PSF and OSB exhibited significant hysteresis, with desorption being much slower than sorption. A porous media diffusion model that assumes instantaneous local equilibrium governed by a nonlinear Freundlich isotherm was found to explain the hysteresis in hexanal transport. A new nonlinear sorption and porous diffusion emissions model was, therefore, developed and partially validated using independent chamber data. The results were also compared to the more conventional linear Fickian-diffusion emissions model. While the linear emissions model predicts styrene emissions from PSF with reasonable accuracy, it substantially underestimates the rate of hexanal emissions from OSB. Although further research and more rigorous validation is needed, the new nonlinear emissions model holds promise for predicting emissions of polar VOCs such as hexanal from porous building materials.     

Sorption-desorption behavior of polybrominated diphenyl ethers in soils

Polybrominated diphenyl ethers (PBDEs) are flame retardants that are commonly found in commercial and household products. These compounds are considered persistent organic pollutants. In this study, we used 4,4′-dibromodiphenyl ether (BDE-15) as a model compound to elucidate the sorption and desorption behavior of PBDEs in soils. The organic carbon-normalized sorption coefficient (K_OC) of BDE-15 was more than three times higher for humin than for bulk soils. However, pronounced desorption hysteresis was obtained mainly for bulk soils. For humin, increasing concentration of sorbed BDE-15 resulted in decreased desorption. Our data illustrate that BDE-15 and probably other PBDEs exhibit high sorption affinity to soils. Moreover, sorption is irreversible and thus PBDEs can potentially accumulate in the topsoil layer. We also suggest that although humin is probably a major sorbent for PBDEs in soils, other humic materials are also responsible for their sequestration.     

Effect of lead on the sorption of 2,4,6-trichlorophenol on soil and peat

The effect of lead on the sorption of 2,4,6-trichlorophenol (2,4,6-TCP) on soil and peat was investigated using a batch equilibration method. Lead markedly diminished the sorption of 2,4,6-TCP, and 2,4,6-TCP had little effect on lead sorption. Peat was a more effective adsorbent for 2,4,6-TCP than soil. The desorption hysteresis of 2,4,6-TCP verified the presence of high-energy sorption sites. Mechanisms of lead suppression effect on the 2,4,6-TCP sorption included the following: Firstly, lead accelerated the aggregation of colloids, the aggregates covered the surface in part and shrunk the pore sizes of the adsorbents, hence decreased the sorption of 2,4,6-TCP. Secondly, X-ray absorption and Fourier transform infrared spectroscopy study suggested that lead competed with 2,4,6-TCP for carboxylic, phenolic and Si-OH groups of organic matter and clay minerals. Such competition was partly responsible for the overall suppression effect of lead on the sorption of 2,4,6-TCP.     

Effect of Pinus radiata derived biochars on soil sorption and desorption of phenanthrene

Biochars are anthropogenic carbonaceous sorbent and their influences on the sorption of environmental contaminants need to be characterized. Here we evaluated the effect of Pinus radiata derived biochars on soil sorption and desorption of phenanthrene. Two biochars separately produced at 350 °C and 700 °C and three soils were tested. Biochar amendment generally enhanced the soil sorption of phenanthrene. The biochar produced at 700 °C generally showed a greater ability at enhancing a soil’s sorption ability than that prepared at 350 °C. The single-step desorption measurement showed an apparent hysteresis in biochar-amended soils. After 28 d equilibration, the sorptive capacity of biochar-amended soil (with an organic carbon content of 0.16%) significantly decreased. This study clearly suggested that biochar application enhanced soil sorption of hydrophobic organic compounds, but the magnitude of enhancement depended on the preparation of biochars, the indigenous soil organic carbon levels, and the contact time between soil and biochar.     

Sorption-desorption behavior of polycyclic aromatic hydrocarbons in upstream and downstream river sediments

Sorption and desorption behaviors of phenanthrene and naphthalene were studied with the whole sediment, humic acid (HA) and humin samples from downstream and upstream sites along the Kishon River, Israel. The 13C nuclear magnetic resonance spectra and the sorption coefficients suggest that sorption occurs to both aromatic and aliphatic moieties of the sedimentary organic matter and that rigid paraffinic domains probably contribute to the sorption non-linearity. The carbon-normalized Freundlich affinity values for the two sorbates were significantly higher for the whole sediment and humin samples from the downstream region of the river than for the upstream sediment samples. On the basis of the measured affinity values, the sorbents can be arranged in the following order: humin>HA>whole sediment. Phenanthrene exhibited the lowest desorption from the whole sediment samples compared with the other sorbents. For naphthalene, the desorption hysteresis obtained with the whole sediment and humin samples were similar: both exhibited a decrease in desorption with decreasing solute concentration. The higher sorption affinities observed for all the organic fractions from the downstream sediment are suggested to be related to the low levels of polar domains and humin content. It is concluded that in bulk sediment samples, the overall contribution of the HA fraction to short-term sorption is of high importance, but the sorption non-linearity is controlled mainly by the humin complexes. The low desorption potential recorded for the whole sediment samples could affect the natural attenuation of the sorbed hydrophobic organic compounds.     

Temperature effects on chlorinated-benzene sorption to hydrophobic surfaces

Sorption and desorption of chlorinated benzenes were investigated in a series of column experiments using porous silica that had phenyl groups bonded to the surface; the mass-fraction organic carbon was 0.016. Both sorption and desorption curves were asymmetrical, but they were mirror images of each other for most experiments, indicating good sorption reversibility. The resulting breakthrough curves were fit to an advection-dispersion mathematical model, with sorption as a first-order, reversible reaction. Significantly greater tailing in the chlorinated-benzene breakthrough curves versus the salt-tracer ones was evidence of slow sorption and desorption. ΔH° values for di-, tri- and tetra-chlorobenzene were 13–21 kJ mol₋₁, indicative of strong van der Waals binding. Despite these small values, slow desorption was attributed to slow binding and release rather than diffusion through the bonded organic phase. Desorption rates decreased in going from di- to tri- to tetra- to penta-chlorobenzene. This decrease was significantly more than the decrease in molecular-diffusion coefficients in the same series, suggesting a chemical rather than a physical rate control. There was less difference in sorption rates through the series, suggesting an inverse relation between partition coefficient and desorption rate. ΔG° values were −17 to −23 kJ mol⁻¹, giving TΔS° values of about 4 kJ mol⁻¹. Thus enthalpic contributions to sorption appear to be of greater importance than entropic contributions.     

Sorption behavior of a new acidic herbicide in soils

The sorptive behavior of the experimental herbicide quinmerac (7-chloro-3-methyl-quinoline-8-carboxylic acid) was investigated in soils of different organic carbon content. Distribution coefficients are low (K_d = 0.03 - 12 mL g⁻¹) and are mainly determined by the soil organic carbon content. The adsorption mechanism operating in neutral to slightly acid agricultural soils is supposed to be cation bridging with the anionic form of quinmerac. Under acid conditions (pH 5.2) the predominating sorption mechanism is hydrophobic interaction. Therefore soil pH and cationic composition are also major factors determining the sorptive capacity of soils for quinmerac.

Adsorption kinetics, equilibrium adsorption and desorption isotherms were determined in batch experiments. Sorption kinetics were investigated at various times from 15 min to 96 hours. A two-step sorption behavior with time was found for the anionic form indicating two types of sorption mechanisms or sorption sites. Equilibrium for the first type was reached at a time-scale of minutes and for the second type after 24 hours. Adsorption isotherms were determined for two soil/solution ratios 1/5 and 1/3. Alteration of the adsorbent concentration exerted a strong influence on the adsorption isotherms. An increase of sorption was found with increasing adsorbent concentration. Under natural soil conditions sorption is therefore expected to be higher compared to the batch experiments. Desorption isotherms were obtained using the consecutive desorption method. Desorption hysteresis was not observed which indicates weak interactions. Implications of the results for the movement of quinmerac under field conditions and for models describing transport are discussed.