Temperature-dependent sorption of polycyclic aromatic hydrocarbons on natural and treated sediments

In aqueous environment temperature is considered to play a significant role in the sorption process of polycyclic aromatic hydrocarbons (PAHs) and its influence on the sorption equilibrium is indicative of sorption energies and mechanisms. In this study, sorptions of five PAHs on three heterogeneous sorbents including one river sediment (YHR), one estuary sediment (YRD) and one treated sediment with organic matter removed (IM) were carried out at a range of temperature from 5 °C to 35 °C. Stronger sorptions were observed at lower temperatures, with the equilibrium sorption coefficient K_d increasing 2-5 times as the temperature decreases 30 °C. The increase of K_d value was attributed primarily to the change of PAH water solubility, which predicted 40-75% of the increase of K_d in the sorption process. To provide insight into the sorption mechanism, enthalpy change (ΔH_S) for the sorption process was calculated and the values were observed to be negative for all of the interactions, suggesting that the exothermal sorption of PAHs inversely dependents on temperature. Based on the values of ΔH_S, van der Waals forces were inferred as the main sorption mechanism for the PAHs, especially on the YHR sediment which contained more organic matter. For sorption of larger size PAHs on the sorbents with low organic matter, specific interactions were deduced to contribute to the overall sorption.     

Bioaccumulation and depuration of anthracene in Penaeus monodon (Fibricius) through food ingestion

Understanding on the bioaccumulation and depuration of PAHs (polycyclic aromatic hydrocarbons) in Penaeus monodon is important in seafood safety because it is one of the most popular seafood consumed worldwide. In this study, we used anthracene as the precursor compound for PAHs accumulation and depuration in the shrimp. Commercial feed pellets spiked with anthracene were fed to P. monodon. At 20 mg kg⁻¹ anthracene, P. monodon accumulated 0.1% of the anthracene from the feed. P. monodon deputed the PAH two times faster than its accumulation. The shrimp reduced its feed consumption when anthracene content in the feed exceeded 20 mg kg⁻¹. At 100 mg kg⁻¹ anthracene, P. monodon started to have necrosis tissues on the posterior end of their thorax. The bioaccumulation factor (BAF), uptake rate constant (k₁) and depuration rate constant (k₂) of anthracene in P. monodon were 1.15 × 10⁻³, 6.80 × 10⁻⁴ d⁻¹ and 6.28 × 10⁻¹ d⁻¹, respectively. The depuration rate constant is about thousand times higher than the uptake rate constant and this indicated that this crustacean is efficient in depurating hydrocarbons from their tissue.     

Distribution of PAHs in tissues of wetland plants and the surrounding sediments in the Chongming wetland, Shanghai, China

Polycyclic aromatic hydrocarbons (PAHs) concentrations were determined in sediments and three types of wetland plants collected from the intertidal flats in the Chongming wetland. The concentration of total PAHs in sediments ranged from 38.7 to 136.2 ng g⁻¹. Surface sediment concentrations were higher in regions with plant cover than in bare regions. Rhizome-layer sediments (56.8-102.4 ng g⁻¹) contained less PAHs than surface sediments (0-5 cm). Concentrations of PAHs in plant tissues ranged from 51.9 to 181.2 ng g⁻¹, with highest concentrations in the leaves of Scirpus. Most of the PAHs in the leaves and other plant tissues were low molecular weight compounds (LMW, 2-4 rings), and a similar distribution pattern of PAHs in different types of plants was also observed. Source analysis indicated that plants and sediments both came from pyrogenic sources, but plants had additional petroleum contamination. The low ratio of benzo[a]anthracene over chrysene suggests that the wetland PAHs came mainly from long-distance atmospheric transportation. Significant bioaccumulation of PAHs from the sediments into plants was not observed for high molecular weight PAHs (HMW, 5-6 rings) in Chongming wetland. The small RCFs (root concentration factor from sediments) for HMW PAHs and large RCFs for LMW PAHs suggested that roots accumulated LMW PAHs selectively from sediments in Chongming wetland.     

Sorption of polycyclic aromatic hydrocarbons (PAHs) on glass surfaces

Sorption of polycyclic aromatic hydrocarbons (PAHs) to glass commonly used in laboratories was studied. Sorption coefficients (K_d) of five selected PAHs to borosilicate glass surfaces were measured using column chromatography. A linear relationship between log K_d and the corresponding water solubility of the subcooled liquid (log S_w) of the investigated PAHs was observed. Based on the determined sorption coefficients our data revealed that mass loss caused by sorption on glass walls strongly depends on the ratio of solution volume to contacted surface area (V/S). The influence of solution chemistry such as ionic strength, solution pH, presence of cosolvent, and the influence of temperature on the sorption process were investigated. In the presence of ionic strength, sorption coefficients concurrently increased but less than a factor of 2 up to 0.005 M calcium chloride concentration. However, further increasing ionic strength had no influence on K_d. The cosolvent reduced sorption at a concentration of methanol in water above 0.5% (v/v); however, for benzo[a]pyrene even with 10% (v/v) methanol the mass loss would be still higher than 10% (with a V/S ratio less than 0.25). Significant effects of the solution pH and temperature were not observed. These results suggest that van der Waal’s forces dominate the sorption process. In the analysis of highly hydrophobic PAHs in aqueous samples, mass loss due to sorption on glass walls should be accounted for in the final result if untreated glass is used. The presented relationship between log K_d and log S_w may help to decide if such a correction is necessary. Furthermore, the frequently used silanization of glass surfaces may not be sufficient to suppress sorption for large PAHs.     

Compositional fractionation of polycyclic aromatic hydrocarbons (PAHs) in mosses (Hypnum plumaeformae WILS.) from the northern slope of Nanling Mountains,South China

High mountains may serve both as condenser for vapor phase persistent organic pollutants (POPs) and as barrier/sink for particulate associated less volatile POPs. The fractionation of POPs along altitudinal profiles is of interest in understanding the role of high mountains in the atmospheric transport of POPs. In the present study, polycyclic aromatic hydrocarbons (PAHs) in a selected moss species, Hypnum plumaeformae WILS, from two altitudinal profiles on the northern slope of Nanling mountains in Southern China were analyzed and compared with those in air samples. The total PAH concentration in the mosses was 310–1340 ng g⁻¹ dry weight, with phenanthrene being the most abundant. The distribution patterns of PAHs in the moss samples matched well with those in bulk atmosphere deposition in the adjacent source areas. The PAH distribution pattern in the mosses was a composite of both particle-associated and vapor phase PAHs, with heavy PAHs are susceptible to uptake/retention by mosses than light PAHs. A plot of log (C_moss/C_air) against log K_oa gave a good linear relationship in the log K_ao range of 6.7–10.2. It is suggested that the widely spread moss, H. plumaeformae WILS, can be used as an effective tool in the biomonitoring of atmospheric PAHs pollution in East Asia. The concentrations of most PAHs in the mosses generally declined with increasing altitude. In addition, there was a shift in compound pattern with an increase in the proportion of light PAHs (2–3 rings), a decrease in heavy PAHs (5–6 rings) and a relatively stable content of 4-ring PAHs. A combination of particulate scavenging and cold condensation are proposed as the major mechanisms for the compositional fractionation of PAHs along the altitudinal profile.     

Predicting bioavailability of PAHs in field-contaminated soils by passive sampling with triolein embedded cellulose acetate membranes

Triolein embedded cellulose acetate membrane (TECAM) was used for passive sampling of the fraction of naphthalene, phenanthrene, pyrene and benzo[a]pyrene in 18 field-contaminated soils. The sampling process of PAHs by TECAM fitted well with a first-order kinetics model and PAHs reached 95% of equilibrium in TECAM within 20 h. Concentrations of PAHs in TECAM (C_TECAM) correlated well with the concentrations in soils (r² = 0.693-0.962, p < 0.001). Furthermore, concentrations of PAHs determined in the soil solution were very close to the values estimated by C_TECAM and the partition coefficient between TECAM and water (K_TECAM-w). After lipid normalization nearly 1:1 relationships were observed between PAH concentrations in TECAMs and earthworms exposed to the soils (r² = 0.591-0.824, n = 18, p < 0.01). These results suggest that TECAM can be a useful tool to predict bioavailability of PAHs in field-contaminated soils.     

Black carbon (BC) in urban and surrounding rural soils of Beijing, China: spatial distribution and relationship with polycyclic aromatic hydrocarbons (PAHs)

The concentrations of black carbon (BC), total organic carbon (TOC) and polycyclic aromatic hydrocarbons (PAHs) have been determined in soils from urban and rural areas of Beijing. The rural area can be divided into plain and mountainous areas which are close to and relatively far from the urban area, respectively. Concentration of BC (5.83 ± 3.05 mg g⁻¹) and BC/TOC concentration ratio (0.37 ± 0.15) in Beijing’s urban soil are high compared with that in world background soils and rural soils of Beijing, suggesting the urban environment to be an essential source and sink of BC. Concentration of BC in the urban area decreases from the inner city to exterior areas, which correlates with the urbanization history of Beijing and infers accumulation of BC in old urban soils. Black carbon in Beijing soils mainly comes from fossil fuel combustion, especially traffic emission. Median PAH concentration in the urban area (502 ng g⁻¹) is one order of magnitude higher than that in the rural plain (148 ng g⁻¹) and mountainous area (146 ng g⁻¹) where PAHs are supposed to mainly come from atmospheric deposition from the urban area. Concentrations of BC correlate significantly with those of PAHs (p < 0.01, except naphthalene) in the urban area and with those of heavier 4-, 5- and 6- ring PAHs (p < 0.01) in the adjacent rural plain area, while there is no significant correlation with any PAH in the farther rural mountainous area.     

Enrichment of polycyclic aromatic hydrocarbons (PAHs) in mariculture sediments of Hong Kong

Surface and core sediments collected from six fish farms in Hong Kong and from reference sites were investigated for the enrichment and sources of polycyclic aromatic hydrocarbons (PAHs). Moderately high ∑PAH₁₆ levels (123-947 ng g⁻¹, mean: 450 ng g⁻¹) were found in the surface aquaculture sediments. In comparison with the sediments from the reference sites, the average enrichment percentage of total organic carbon (TOC) and PAHs in surface sediments were 21.4 and 43.8%, respectively, and in the core sediments, 24.6 and 73.7%, respectively. Mathematical source apportionment analyses (i.e. isomer ratios, hierarchical cluster analysis, principal components analysis with multiple linear regression analysis) suggested a higher percentage of petrogenic sources in aquaculture sediments. The fish feeds might be the main source of the enriched PAHs in the aquaculture sediments. To our knowledge, this is the first study showing that PAHs in aquaculture sediments could be attributed to human aquaculture activities.     

Determination of polycyclic aromatic hydrocarbons in urban street dust: implications for human health

The determination of sixteen polycyclic aromatic hydrocarbons in urban street dust has been done. Samples were collected from 12 sampling locations in a city centre location (Newcastle upon Tyne, north east England) and extracted using in situ pressurised fluid extraction followed by gas chromatography mass spectrometry. From the results it was possible to identify three groups, with respect to PAH concentration, with PAH contents ranging between 0.6-2.3 mg kg⁻¹, 15.6-22.5 mg kg⁻¹ and 36.1-46.0 mg kg⁻¹. The total PAH content of samples from these sampling sites has been compared to 22 urban locations around the world; comparable levels were found in these samples compared to the other cities around the world.The potential source of PAHs has been investigated by investigating the proportion of pyrogenic and petrogenic material in urban street dust using specific individual PAH ratios. The results indicate that the PAH content of urban street dust from the chosen sites are more likely to be due to pyrogenic sources i.e. vehicle exhaust emissions. The particle size fractions (<63 μm; 63-125 μm; 125-250 μm; 250-500 μm; 500-1000 μm; and 1000-2000 μm) of individual PAHs in three selected sampling sites was investigated. In two of the selected sites the PAH content was independent of particle size whereas in sampling site 10 elevated PAH levels are noted in the <63 μm size fraction. Sampling site 10 is located at the junction of three road tributaries which are used as major access points to the east of the city centre. Finally, the potential health risk for unintentional consumption of PAHs was assessed in terms of a mean daily intake (based on an ingestion rate of 100 mg d⁻¹). It was found that all 4-6 membered ring PAHs had concentrations in excess of the mean daily intake thereby reflecting a potential health risk, particularly in the smallest size particle fractions.     

Source apportionment of atmospheric polycyclic aromatic hydrocarbons (PAHs) in Palm Beach County,Florida

Due to concerns about adverse health effects associated with inhalation of atmospheric polycyclic aromatic hydrocarbons (PAHs), 30 ambient air samples were obtained at an air quality monitoring station in Palm Beach County, Florida, from March 2013 to March 2014. The ambient PAH concentration measurements and fractional emission rates of known sources were incorporated into a chemical mass balance model, CMB8.2, developed by EPA, to apportion contributions of three major PAH sources including preharvest sugarcane burning, mobile vehicles, and wildland fires. Strong association between the number of benzene rings and source contribution was found, and mobile vehicles were identified to be the prevailing source (contribution ≥56%) for the observed PAHs concentration with lower molecular weights (four or fewer benzene rings) throughout the year. Preharvest sugarcane burning was the primary contributing source for PAHs with relatively higher molecular weights (five or more benzene rings) during the sugarcane burning season (from October to May of the next year). Source contribution of wildland fires varied among PAH compounds but was consistently lower than for sugarcane burning during the sugarcane harvest season. Determining the major sources responsible for ground-level PAHs serves as a tool to improving management strategies for PAH emitting sources and a step toward better protection of the health of residents in terms of exposure to PAHs. The results obtain insight into temporal dominance of PAH polluting sources for those residential areas located near sugarcane burning facilities and have implications beyond Palm Beach County, in areas with high concerns of PAHs and their linked sources.

Implications: Source apportionment of atmospheric polycyclic hydrocarbons (PAHs) in Palm Beach County, Florida, meant to estimate contributions of major sources in PAH concentrations measured at Belle Glade City of Palm Beach County. Number of benzene rings was found to be the key parameter in determining the source with the prevailing contribution. Mobile vehicle sources showed a higher contribution for species with four or fewer benzene rings, whereas sugarcane burning contributed more for species with five or more benzene rings. Results from this study encourage more control for sugarcane burns and help to better manage authorization of the sugarcane burning incidents and more restrictive transportation plans to limit PAH emissions from mobile vehicles.     

Respiratory uptake kinetics of neutral hydrophobic organic chemicals in a marine benthic fish, Pseudopleuronectes yokohamae

We investigated the respiratory uptake kinetics of polychlorinated biphenyls (PCBs), organohalogen pesticides (OCPs), polycyclic aromatic hydrocarbons (PAHs), and 2,2′,4,4′-tetrabrominated diphenyl ether (BDE #47) in a marine benthic fish, Pseudopleuronectes yokohamae. The respiratory uptake efficiencies (E_W) of the chemicals, of which there have been no reports for the majority of persistent organic pollutants (POPs), were obtained by measuring the respiratory uptake rate constants (k₁) and the oxygen consumption rates of fish. Fish were exposed to water in which these chemicals were dissolved at environmentally relevant concentrations for 28 d, followed by 168 d of depuration in clean seawater. The k₁ and E_W values for 99 compounds were obtained, and they ranged from 2000 to 42 000 L kg-lipid⁻¹ d⁻¹ and from 0.060 to 1.3, respectively. The E_W values of the chemicals, except for PAHs, tended to increase with increasing values of the log octanol–water partition coefficients (K_OW) of the chemicals up to a log K_OW of 5. For log K_OW in the range 3–5, the E_W values in this study were much lower than those in a published study (about one-third). As a result of analysis by a two-phase resistance model, the resistance of transport rates to the lipid phase in this study was lower than was the case in the published study. These findings indicate that the E_W predicted by the published study for log K_OW in the range 3–5 may differ among fish species and water temperature, and further study is needed.     

Desorption of polycyclic aromatic hydrocarbons from field-contaminated soil to a two-dimensional hydrophobic surface before and after bioremediation

This study investigated environmental distributions and production mechanisms of chlorinated polycyclic aromatic hydrocarbons (Cl-PAHs) in the sediments from some tidal flats located in Asia. Cl-PAHs were found in sediments taken from Arao tidal flat, Kikuchigawa River and Shirakawa River. The range of ∑Cl-PAHs was from 25.5 to 483 pg g⁻¹ for Kikuchigawa River and Arao tidal flat, respectively.Concentrations of PAHs and Cl-PAHs showed no significant correlations (r = 0.134). This result suggests that the origins of these compounds differ. In the identified Cl-PAH isomers, the most abundant Cl-PAH isomer was 9,10-dichloroanthracene (9,10-di-Cl-ANT) in the three sites. In general, concentrations of Cl-ANTs in the coastal environment are about 3-5 orders of magnitude lower than those of anthracene (ANT). However, concentration ratios between Cl-ANTs and ANT (Cl-ANTs/ANT) in the sediments ranged from 4.1% to 24.6%. This result indicated that Cl-PAHs were not generated under industrial processes but the high concentration ratios have resulted from the contribution of photochemical production of Cl-ANTs in the sediments because ANT is known to have high photochemical reactivity.For examining this phenomenon, ANT adsorbed onto glass beads was irradiated with UV under the mimicked field conditions of tidal flats. As a result, it was noticed that, while chlorinated derivatives were negligible in a light-controlled group, production of 2-Cl-ANT, 9-Cl-ANT and 9,10-diCl-ANT on the irradiated surface were found in this study. These results suggest that photochemical reaction of PAHs can be a potential source of the occurrence of Cl-PAHs in the coastal environment.     

Disappearance of polycyclic aromatic hydrocarbons sorbed on surfaces of pine [Pinua thunbergii] needles under irradiation of sunlight: Volatilization and photolysis

The solar photodegradation of 16 polycyclic aromatic hydrocarbons (PAHs), sorbed on surfaces of pine [Pinua thunbergii] needles was investigated. The PAHs were produced by combustion of polystyrene and exposed onto the surfaces of pine needles. The disappearance of PAHs sorbed on the pine needle surfaces is mainly caused by volatilization and photolysis, with photolysis playing a major role. The volatilization rates correlate with PAH molecular weight significantly. The photolysis of the 16 PAHs follows first-order kinetics and their photolysis half-lives (t_1/2,P) range from 12.9 h for naphthalene to 65.4 h for fluorene. The PAHs have similar half-lives whether they are sorbed on spruce or pine needles. Compared with water, the cuticular waxes of pine needles can stabilize photolysis of PAHs and facilitate accumulation of PAHs. t_1/2,P for selected PAHs correlate with semi-empirically calculated energy of the highest occupied orbital (E_HOMO). Photochemical behaviors of PAHs are dependent not only on their molecular structures but also the physical–chemical properties of the substrate on which they are adsorbed.     

Characterization of extractable and non-extractable polycyclic aromatic hydrocarbons in soils and sediments from the Pearl River Delta, China

Formation of bound residues of pollutants in soils and sediments is an important process to control the fate of pollutants in the environment. The most of bound residue is not solvent extractable. In this paper, we measured both extractable and non-extractable polycyclic aromatic hydrocarbons (PAHs) in different organic matter fractions of samples from the Pearl River Delta, China. Non-extractable PAHs concentration was 234.45-1424.57 μg/kg and accounted for 33.78-57.44% of total PAHs. 2-3 Ring PAHs were the dominant species and differed in concentration substantially between the samples. The atomic ratio of PAHs over organic-C in the fractions ordered as solvent soluble organic matter > humin > humic acids, matching the content of aliphatic moieties in the fractions of organic matter. The ratio of extractable and non-extractable PAHs may relate to the aging process of PAHs in soil and sediment.     

Sedimentary record of PAHs in the Liangtan River and its relation to socioeconomic development of Chongqing, Southwest China

Concentrations of polycyclic aromatic hydrocarbons (PAHs) were detected in sediment cores and surface sediment samples from the Liangtan River of Chongqing, Southwest China. The total concentration of 16 PAHs ranged from 69 to 6251 ng g⁻¹. The spatial distribution of the PAHs reflects the intensity and scope of human activity in the catchment. A historical record of PAH contamination was reconstructed using a sediment core from a background segment of the river. The characteristic changes of concentrations, fluxes and patterns of 16 PAHs over the past ∼90 years were captured in detail. An obvious peak of PAH concentration and flux was found in the 1940s, i.e., during war time, and then a sharp increase was observed from the early 1980s to the present. The maximum concentration and flux reached 1260 ng g⁻¹ and 470 ng cm⁻² year⁻¹, respectively. The sharp increase was attributed to the contribution of pyrogenic sources of PAHs. The population, length of highways and energy consumption of Chongqing, as indexes of socioeconomic development, were positively correlated with PAH input in the sediment core from the 1950s to the present. The results clearly show that the local socioeconomic development in the last decades remarkably aggravated the environmental load of sedimentary PAHs.     

Spatial and temporal distribution of polycyclic aromatic hydrocarbons (PAHs) in sediments from Daya Bay, South China

The spatial and temporal distribution of polycyclic aromatic hydrocarbons (PAHs) has been investigated in Daya Bay, China. The total concentration of the 16 USEPA priority PAHs in surface sediments ranged from 42.5 to 158.2 ng/g dry weight with a mean concentration of 126.2 ng/g. The spatial distribution of PAHs was site-specific and combustion processes were the main source of PAHs in the surface sediments. Total 16 priority PAH concentration in the cores 8 and 10 ranged from 77.4 to 305.7 ng/g and from 118.1 to 319.9 ng/g respectively. The variation of the 16 PAH concentrations in both cores followed the economic development in China very well and was also influenced by input pathways. Some of the PAHs were petrogenic in core 8 while pyrolytic source was dominant in core 10. In addition, pyrolytic PAHs in both cores were mainly from the coal and/or grass and wood combustion.     

Lethal and sublethal effects of naphthalene and 1,2-dimethylnaphthalene on naupliar and adult stages of the marine cyclopoid copepod Oithona davisae

Short-term (24 h) exposure experiments have been conducted to determine the effects of two environmental relevant polycyclic aromatic hydrocarbons (PAHs), naphthalene (NAPH) and dimethylnaphthalene (C2-NAPH), on the naupliar and adult stages of the marine cyclopoid copepod Oithona davisae. To resemble more realistic conditions, those exposure experiments were conducted under the presence of food. The naupliar stages evidenced lower tolerance to PAH exposure regarding narcotic and lethal effects than adults. Copepod feeding activity showed to be very sensitive to the presence of the studied PAHs, detrimental effects occurring at toxic concentrations ca. 2-3 fold lower than for narcotic effects. In addition we report PAH-mediated changes in cell size and growth rate of the prey item, the heterotrophic dinoflagellate Oxyrrhis marina, that could indirectly affect copepod feeding and help explain hormesis-like responses in our feeding experiments.     

Persistent organic pollutants in plastic marine debris found on beaches in San Diego, California

Plastic debris were collected from eight beaches around San Diego County, California. Debris collected include: pre-production pellets and post-consumer plastics including fragments, polystyrene (PS) foam, and rubber. A total of n = 2453 pieces were collected ranging from <5 mm to 50 mm in size. The plastic pieces were separated by type, location, and appearance and analyzed for polycyclic aromatic hydrocarbons (PAHs), polychlorinated biphenyls (PCBs), dichlorodiphenyltrichloroethane (DDT) and its breakdown products, and chlordanes. PAH concentrations ranged from 30 ng g⁻¹ to 1900 ng g⁻¹, PCBs from non-detect to 47 ng g⁻¹, chlordanes from 1.8 ng g⁻¹ to 60 ng g⁻¹, and DDTs from non-detect to 76 ng g⁻¹. Consistently higher PAH concentrations found in PS foam samples (300-1900 ng g⁻¹) led us to examine unexposed PS foam packaging materials and PS virgin pellets. Unexposed PS foam contained higher concentrations of PAHs (240-1700 ng g⁻¹) than PS virgin pellets (12-15 ng g⁻¹), suggesting that PAHs may be produced during manufacturing. Temporal trends of debris were investigated at one site, Ocean Beach, where storm events and beach maintenance were found to be important variables influencing debris present at a given time.     

Decomposition of 2,2',4,4',5,5'-hexachlorobiphenyl with iron supported on an activated carbon from an ion-exchange resin

An activated carbon (AC) containing a high concentration (374 mg g⁻¹) of Fe was prepared by carbonization of an ion-exchange resin. To examine its chemical reactivity as a catalyst to decompose 2,2′,4,4′,5,5′-hexachlorobiphenyl (PCB-153), the decomposition parameters of temperature and time were varied under air or N₂. Decomposition at 350 °C was achieved within 15 min under air and 30 min under N₂, and the efficiency of PCB-153 decomposition was 99.7% and 98.0%, respectively. An analysis of inorganic chloride ions revealed that PCB-153 was mineralized effectively during the decomposition. The Brunauer-Emmett-Teller (BET) surface area and pore volume of the AC were measured to assess the adsorption capacity before and after the decomposition. The differences between decomposition under air and N₂ reflected the differences in the BET surface and pore volume measurements. A decomposition pathway was postulated, and the reactive characteristics of chlorine atoms loaded on the benzene rings followed the order of para > meta > ortho, which agrees with the calculated results from a density functional theory study.