Occurrence of polycyclic musks in wastewater and receiving water bodies and fate during wastewater treatment

The occurrence of cashmerane (DPMI), celestolide, phantolide, traesolide (ATII), galaxolide (HHCB) and tonalide (AHTN) in sewage and surface waters and their fate during wastewater treatment and anaerobic sludge digestion is investigated. AHTN and HHCB are the most important representatives and influent concentrations of 0.41-1.8 and 0.9-13 μg L⁻¹ are observed. DPMI is detected in influent and effluent samples but in notably lower concentrations than AHTN and HHCB. Major sources of polycyclic musks are households, whereas industrial emitters seem to be of minor importance. This conclusion is supported by the analysis of selected industrial wastewaters (metal, textile and paper industry). Specific emissions of 0.36 ± 0.19 and 1.6 ± 1.0 mg cap⁻¹ d⁻¹ for AHTN and HHCB are calculated. Overall removal efficiencies between approx 50% and more than 95% are observed during biological wastewater treatment and removal with the excess sludge is the major removal pathway. Log K_D values of 3.73-4.3 for AHTN, 3.87-4.34 for HHCB and 2.42-3.22 for DPMI are observed in secondary sludge. During sludge digestion no or only slight removal occurred. Mean polycyclic musk concentrations in digested sludge amounted to 1.9 ± 0.9 (AHTN), 14.2 ± 5.8 (HHCB), 0.8 ± 0.4 (ATII) and 0.2 ± 0.09 (DPMI) mg kg⁻¹ dry matter. In the receiving water systems a comparable distribution as during wastewater treatment is observed. AHTN, HHCB and DPMI are detected in surface waters (ND (not detected) - < 0.04, ND - 0.32 and ND - 0.02 μg L⁻¹) as well as AHTN and HHCB in sediments (ND - 20, ND - 120 μg kg⁻¹). For HHCB an apparent K_OC value of 4.1-4.4 is calculated for sediments. Major source for polycyclic musks in surface waters are discharges from wastewater treatment plants. For HHCB and DPMI 100% of the load observed in the sampled surface waters derive from discharges of treated wastewater.     

Removal of tetrabromobisphenol A by conventional activated sludge, submerged membrane and membrane aerated biofilm reactors

The goal of this study was to compare removal efficiencies of tetrabromobisphenol A (TBBPA) using typical wastewater treatment technologies, and to identify the most significant mechanisms of removal. Two types of municipal wastewater reactors were studied: a full-scale conventional activated sludge (CAS) reactor with tertiary treatment; and three pilot-scale membrane bioreactors (MBRs) having different sludge retention times (SRTs). All four reactors were fed the same influent. A third reactor type, a membrane aerated biofilm reactor (MABR) was fed tap water, ammonia, and TBBPA. TBBPA in municipal influent ranged from 1 to 41 ng L⁻¹ (n = 10). The CAS effluent had an average TBBPA concentration of 0.7 ± 1.3 ng L⁻¹ (n = 3). Effluent concentrations from the MBRs were an average of 6 ± 6 ng L⁻¹ TBBPA (n = 26). Significant TBBPA removal was observed in the MABR throughout the 5 week of study (p ? 0.05). Removal of TBBPA from wastewater treatment was found to be due to a combination of adsorption and biological degradation. Based on experimental results, nitrification is likely a key process therein. No significant relationship between removal of TBBPA and SRT was identified (p ? 0.05).     

Identification of two new cytochrome P450 genes and RNA interference to evaluate their roles in detoxification of commonly used insecticides in Locusta migratoria

Composite samples of Australian farmed Yellowtail Kingfish (Seriola lalandi) (YTKF) (n = 27), Mulloway (Argyrosomus hololepidotus) (n = 6) and manufactured feed (n = 5) were analysed to benchmark levels of a broad range of residues and contaminants of potential public health and trade significance. A subset of these samples [YTKF (n = 5), Mulloway (n = 2) and feed (n = 5)] was analysed for dioxins and polychlorinated biphenyls (PCBs). The mean concentration of dioxins in YTKF was 0.6 pg TEQ g⁻¹ (range 0.22-0.8) and in Mulloway was 0.16 pg TEQ g⁻¹ (range 0.16-0.16). The mean concentration of dioxins and dioxin-like PCBs in YTKF was 2.6 pg TEQ g⁻¹ (range 1.4-3.5), while Mulloway had a mean concentration of 0.67 pg TEQ g⁻¹ (range 0.57-0.76). The mean concentration of PCBs in YTKF was 21 μg kg⁻¹ (range 8.6-29) and in Mulloway was 5.4 μg kg⁻¹ (mean 4.7-6). The mean concentration of dioxin-like PCBs in YTKF was 2.1 pg TEQ g⁻¹ (range 1.2-2.8) and in Mulloway was 0.51 pg TEQ g⁻¹ (range 0.41-0.61). The mean mercury concentration in YTKF was 0.03 mg kg⁻¹ (range 0.02-0.05) and in Mulloway it was 0.02 mg kg⁻¹ (range 0.02-0.04). There were no detectable levels of any pesticide or antimicrobial compounds in any sample of YTKF or Mulloway. Attention is drawn to technical differences in port of entry testing programs such as sampling strategies, portion tested, laboratory methodology, residue definitions and reporting conventions that exporters’ products may be subject to. All residues and contaminants were either undetectable or present at very low levels when judged against Australian, Japanese and European Union regulatory standards (where set).     

Applicability of microwave-assisted extraction combined with LC-MS/MS in the evaluation of booster biocide levels in harbour sediments

A new sample treatment method for the determination of four common booster biocides (Diuron, TCMTB, Irgarol 1051 and Dichlofluanid) in harbour sediment samples has been developed that uses liquid chromatography-tandem mass spectrometry (LC-MS/MS) after microwave-assisted extraction, followed by clean-up and a solid phase extraction preconcentration step (MAE-SPE). The effects of different variables on MAE-SPE were studied. The recoveries obtained were greater than 75%, and the relative standard deviation was less than 7%. The detection limits ranged between 0.1 and 0.3 ng g⁻¹. The developed methodology was successfully applied to the evaluation of the presence of booster biocides in sediment samples from different harbours and marinas of Gran Canaria Island (Canary Islands, Spain).     

Efficient degradation of organic pollutants with ferrous hydroxide colloids as heterogeneous Fenton-like activator of hydrogen peroxide

The capacity of a full-scale reclamation pond-constructed wetland (CW) system to eliminate 27 emerging contaminants (i.e. pharmaceuticals, sunscreen compounds, fragrances, antiseptics, fire retardants, pesticides, and plasticizers) and the seasonal occurrence of these contaminants is studied. The compounds with the highest concentrations in the secondary effluent are diclofenac, caffeine, ketoprofen, and carbamazepine. The results show that the constructed wetland (61%) removes emerging contaminants significantly more efficiently than the pond (51%), presumably due to the presence of plants (Phragmites and Thypa) as well as the higher hydraulic residence time (HRT) in the CW. A greater seasonal trend to the efficient removal of these compounds is observed in the pond than in the CW. The overall mass removal efficiency of each individual compound ranged from 27% to 93% (71% on average), which is comparable to reported data in advanced treatments (photo-fenton and membrane filtration). The seasonal average content of emerging contaminants in the river water (2488 ng L⁻¹) next to the water reclamation plant is found to be higher than the content in the final reclaimed water (1490 ng L⁻¹), suggesting that the chemical quality of the reclaimed water is better than available surface waters.     

Immunotoxicity in ascidians: antifouling compounds alternative to organotins: III--the case of copper(I) and Irgarol 1051

After the widespread ban of TBT, due to its severe impact on coastal biocoenoses, mainly related to its immunosuppressive effects on both invertebrates and vertebrates, alternative biocides such as Cu(I) salts and the triazine Irgarol 1051, the latter previously used in agriculture as a herbicide, have been massively introduced in combined formulations for antifouling paints against a wide spectrum of fouling organisms. Using short-term (60 min) haemocyte cultures of the colonial ascidian Botryllus schlosseri exposed to various sublethal concentrations of copper(I) chloride (LC₅₀ = 281 μM, i.e., 17.8 mg Cu L⁻¹) and Irgarol 1051 (LC₅₀ > 500 μM, i.e., >127 mg L⁻¹), we evaluated their immunotoxic effects through a series of cytochemical assays previously used for organotin compounds. Both compounds can induce dose-dependent immunosuppression, acting on different cellular targets and altering many activities of immunocytes but, unlike TBT, did not have significant effects on cell morphology. Generally, Cu(I) appeared to be more toxic than Irgarol 1051: it significantly (p < 0.05) inhibited yeast phagocytosis at 0.1 μM (∼10 μg L⁻¹), and affected calcium homeostasis and mitochondrial cytochrome-c oxidase activity at 0.01 μM (∼1 μg L⁻¹). Both substances were able to change membrane permeability, induce apoptosis from concentrations of 0.1 μM (∼10 μg L⁻¹) and 200 μM (∼50 mg L⁻¹) for Cu(I) and Irgarol 1051, respectively, and alter the activity of hydrolases. Both Cu(I) and Irgarol 1051 inhibited the activity of phenoloxidase, but did not show any interactive effect when co-present in the exposure medium, suggesting different mechanisms of action.     

Effects of the pharmaceuticals gemfibrozil and diclofenac on biomarker expression in the zebra mussel (Dreissena polymorpha) and their comparison with standardised toxicity tests

Pharmaceuticals, including the lipid regulator gemfibrozil and the non-steroidal anti-inflammatory drug diclofenac have been identified in waste water treatment plant effluents and receiving waters throughout the western world. The acute and chronic toxicity of these compounds was assessed for three freshwater species (Daphnia magna,Pseudokirchneriella subcapitata, Lemna minor) using standardised toxicity tests with toxicity found in the non-environmentally relevant mid mg L⁻¹ concentration range. For the acute endpoints (IC₅₀ and EC₅₀) gemfibrozil showed higher toxicity ranging from 29 to 59 mg L⁻¹ (diclofenac 47-67 mg L⁻¹), while diclofenac was more toxic for the chronic D. magna 21 d endpoints ranging from 10 to 56 mg L⁻¹ (gemfibrozil 32-100 mg L⁻¹). These results were compared with the expression of several biomarkers in the zebra mussel (Dreissena polymorpha) 24 and 96 h after exposure by injection to concentrations of 21 and 21,000 μg L⁻¹ corresponding to nominal concentrations of 1 and 1000 μg L⁻¹. Exposure to gemfibrozil and diclofenac at both concentrations significantly increased the level of lipid peroxidation, a biomarker of damage. At the elevated nominal concentration of 1000 μg L⁻¹ the biomarkers of defence glutathione transferase and metallothionein were significantly elevated for gemfibrozil and diclofenac respectively, as was DNA damage after 96 h exposure to gemfibrozil. No evidence of endocrine disruption was observed using the alkali-labile phosphate technique. Results from this suite of biomarkers indicate these compounds can cause significant stress at environmentally relevant concentrations acting primarily through oxidation pathways with significant destabilization of the lysosomal membrane and that biomarker expression is a more sensitive endpoint than standardised toxicity tests.     

Contamination by chlorinated pesticides, PCBs and PBDEs in Atlantic spotted dolphin (Stenella frontalis) in western South Atlantic

Chlorinated pesticides, PCBs and PBDEs were analysed in nine blubber samples of Atlantic spotted dolphins, Stenella frontalis, incidentally captured during fishing operations in southern and southeastern Brazil between 2005 and 2007. The majority of compounds analysed were detected, suggesting widespread contamination over the region. Although the samples came from a location far from main coastal industrial areas, the results revealed an influence from such sources. Therefore, levels of PCBs (774-23 659 ng g⁻¹ lipid wt.) and PBDEs (23-1326 ng g⁻¹ lipid wt.) detected seem to be related to the movement of individuals throughout near-shore and offshore waters. The sample from a lactating female exhibited a lower level of contamination and a distinct pattern, indicating selective transfer favouring less lipophilic compounds.     

Emerging pollutants in sewage, surface and drinking water in Galicia (NW Spain)

A monitoring programme was carried out on wastewater, surface and drinking water on the NW area of Spain during the four seasons of a year period (November 2007-September 2008). This study covered a series of emerging pollutants of different classes, including pharmaceuticals, neutral and acidic organophosphorus flame retardant/plasticizers (OPs), triclosan, phenoxy-herbicides, insect repellents and UV filters. From the total set of 53 compounds, 19 were found in raw wastewater with median concentrations higher than 0.1 μg L⁻¹. Among them, salicylic acid, ibuprofen and the UV filter benzophenone-4 (BP-4) were the most concentrated, exceeding the 1 μg L⁻¹ median value. Subsequently, 11 of these contaminants are not efficiently enough removed in the small WWTPs tested and their median concentrations in effluents still surpassed the 0.1 μg L⁻¹, so that they can spread through surface water. These chemicals are the pharmaceuticals naproxen, diclofenac and atenolol; the OPs tri(2-chloroethyl) phosphate (TCEP), tri(chloropropyl) phosphate (TCPP), tri-n-butyl phosphate (TnBP), diphenyl phosphate (DPhP) and diethylhexyl phosphate (DEHP); and the sulphonate UV filters BP-4 and 2-phenylbenzimidazole-5-sulphonic acid (PBSA). These OPs were then the dominant emerging pollutants occurring in surface and drinking water, where they are detected in the 20-200 ng L⁻¹ range. Pharmaceuticals and UV filters are typically below the 10 ng L⁻¹ level. Finally, herbicides were only detected in the last sampling campaign under the 100 ng L⁻¹ drinking water European Union limit.     

Ozonation as an advanced oxidant in treatment of bamboo industry wastewater

The present study employed ozonation process to treat the bamboo industry wastewater (BIWW). The impact of ozone dosage and initial organic concentration on color, COD and TOC removal rates were studied along with characterization of the major organics in raw and treated wastewater. The results suggested the ozone dosage of 3.15 g h⁻¹ (concentration 52.5 mg L⁻¹) was suitable for the treatment. After 25 min ozonation of 1 L raw wastewater, the color, COD and TOC removal efficiencies were 95%, 56% and 40%, respectively, with an influent COD concentration of 835 mg L⁻¹. The ratio of kg O₃ kg⁻¹ COD at 3.15 g h⁻¹ was 2.8 (<3), revealing that ozonation was a cost effective process for tertiary treatment of BIWW. Longer oxidization time was required to achieve similar results for raw wastewater with higher COD concentration. The chromatogram from gel permeation chromatography revealed that ozonation resulted in the breakdown of high molecular weight compounds into lower molecular weight components but could not completely mineralize the organic matter. The majority of these compounds were identified in both raw and ozonated samples via GC-MS analysis. In addition to ester derivatives as the main intermediates of ozonation, 1-chloroctadecane, methyl stearate, benzophenone and α-cyperone were identified as the by-products of ozonation.     

Effect of vegetation in pilot-scale horizontal subsurface flow constructed wetlands treating sulphate rich groundwater contaminated with a low and high chlorinated hydrocarbon

In order to characterize the effect of vegetation on performance of constructed wetlands (CWs) treating low and high chlorinated hydrocarbon, two pilot-scale horizontal subsurface flow (HSSF) CWs (planted with Phragmites australis and unplanted) treating sulphate rich groundwater contaminated with MCB (monochlorobenzene, as a low chlorinated hydrocarbon), (about 10 mg L⁻¹), and PCE (perchloroethylene, as a high chlorinated hydrocarbon), (about 2 mg L⁻¹), were examined. With mean MCB inflow load of 299 mg m⁻² d⁻¹, the removal rate was 58 and 208 mg m⁻² d⁻¹ in the unplanted and planted wetland, respectively, after 4 m from the inlet. PCE was almost completely removed in both wetlands with mean inflow load of 49 mg m⁻² d⁻¹. However, toxic metabolites cis-1,2-DCE (dichloroethene) and VC (vinyl chloride) accumulated in the unplanted wetland; up to 70% and 25% of PCE was dechlorinated to cis-1,2-DCE and VC after 4 m from the inlet, respectively. Because of high sulphate concentration (around 850 mg L⁻¹) in the groundwater, the plant derived organic carbon caused sulphide formation (up to 15 mg L⁻¹) in the planted wetland, which impaired the MCB removal but not statistically significant. The results showed significant enhancement of vegetation on the removal of the low chlorinated hydrocarbon MCB, which is probably due to the fact that aerobic MCB degraders are benefited from the oxygen released by plant roots. Vegetation also stimulated completely dechlorination of PCE due to plant derived organic carbon, which is potentially to provide electron donor for dechlorination process. The plant derived organic carbon also stimulated dissimilatory sulphate reduction, which subsequently have negative effect on MCB removal.     

Hydrolysis of di-n-butyl phthalate, butylbenzyl phthalate and di(2-ethylhexyl) phthalate in human liver microsomes

Diester phthalates are industrial chemicals used primarily as plasticizers to import flexibility to polyvinylchloride plastics. In this study, we examined the hydrolysis of di-n-butyl phthalate (DBP), butylbenzyl phthalate (BBzP) and di(2-ethylhexyl) phthalate (DEHP) in human liver microsomes. These diester phthalates were hydrolyzed to monoester phthalates (mono-n-butyl phthalate (MBP) from DBP, mono-n-butyl phthalate (MBP) and monobenzyl phthalate (MBzP) from BBzP, and mono(2-ethylhexyl) phthalate (MEHP)) by human liver microsomes. DBP, BBzP and DEHP hydrolysis showed sigmoidal kinetics in V-[S] plots, and the Hill coefficient (n) ranged 1.37-1.96. The S₅₀, V_max and CL_max values for DBP hydrolysis to MBP were 99.7 μM, 17.2 nmol min⁻¹ mg⁻¹ protein and 85.6 μL min⁻¹ mg⁻¹ protein, respectively. In BBzP hydrolysis, the values of S₅₀ (71.7 μM), V_max (13.0 nmol min⁻¹ mg⁻¹ protein) and CL_max (91.3 μL min⁻¹ mg⁻¹ protein) for MBzP formation were comparable to those of DBP hydrolysis. Although the S₅₀ value for MBP formation was comparable to that of MBzP formation, the V_max and CL_max values were markedly lower (<3%) than those for MBzP formation. The S₅₀, V_max and CL_max values for DEHP hydrolysis were 8.40 μM, 0.43 nmol min⁻¹ mg⁻¹ protein and 27.5 μL min⁻¹ mg⁻¹ protein, respectively. The S₅₀ value was about 10% of DBP and BBzP hydrolysis, and the V_max value was also markedly lower (<3%) than those for DBP hydrolysis and MBzP formation for BBzP hydrolysis. The ranking order of CL_max values for monoester phthalate formation in DBP, BBzP and DEHP hydrolysis was BBzP to MBzP ? DBP to MBP > DEHP to MEHP > BBzP to MBP. These findings suggest that the hydrolysis activities of diester phthalates by human liver microsomes depend on the chemical structure, and that the metabolism profile may relate to diester phthalate toxicities, such as hormone disruption and reproductive effects.     

Photo-dissociation of dimethylamine by KrBr excilamp

A study of dimethylamine photo-dissociation in the gas phase has been conducted using UV radiation delivered from a KrBr^* excilamp, driven by a sinusoidal electronic control gear with maximum emission at wavelength of 207 nm. The electrical input power and radiant power of the lamp were measured to determine their effects on the degradation. The influence of flow velocity and initial concentration of dimethylamine were also examined. In order to evaluate the photo-dissociation process comprehensively, several parameters were investigated, including removal efficiency, energy yield, carbon balance and CO₂ selectivity. It is shown that the removal efficiency increases with enhanced input power and decreased gas flow rate. A high removal efficiency of 68% is achieved for lamp power 102 W and flow velocity 15 m³ h⁻¹. The optimum dimethylamine initial concentration is around 3520 mg m⁻³, for which the energy yield reaches up to 442 g kW h⁻¹ when the input power is 65 W. In addition, two chain compounds (1,3-bis-dimethylamino-2-propanol; 3-penten-2-one, 4-amino) and three ring organic matters (1-azetidinecarboxaldehyde, 2,2,4,4-tetramethyl; N-m-tolyl-succinamic acid; p-acetoacetanisidide), were identified by GC–MS as secondary products, in order to demonstrate the pathways of the dimethylamine degradation.     

Molecular and physiological approaches to understand the ecology of methanol degradation during the biofiltration of air streams

A 13.4 L biofilter treating an off-gas stream supplemented with methanol under two different situations was studied in terms of MeOH removal efficiency, microbial ecology and odor removal. During Period 1 (P1) the reactor was packed with wood bark chips with no pH control, treating an off-gas resulting from the aerobic chamber of a membrane biological reactor treating sewage and located outdoor, whereas during Period 2 (P2) a compressed air stream fed with MeOH was treated using PVC rings and maintaining pH at neutral values. Both systems operated at 96 g MeOH m⁻³ h⁻¹ achieving removal efficiencies of around 90% during P1 and 99.9% during P2. The relative activity of biomass developed in both systems was assessed using respirometric analysis with samples obtained from both biofilms. Higher biomass activity was obtained during P2 (0.25-0.35 kg MeOH kg⁻¹ VSS d⁻¹) whereas 1.1 kg MeOH kg⁻¹ VSS d⁻¹ was obtained in the case of P1. The application of molecular and microscopic techniques showed that the eukaryotes were predominant during P1, being the yeast Candida boidinii the most abundant microorganism. A specific Fluorescence in situ hybridization probe was designed for C. boidinii and tested successfully. As a result of the neutral pH, a clear predominance of prokaryotes was detected during P2. Interestingly, some anaerobic bacteria were detected such as Desulfovibrio, Desulfobacteraceae species and also some archaea such as Methanosarcina.     

The influence of mariculture on mercury distribution in sediments and fish around Hong Kong and adjacent mainland China waters

To study the influence of mariculture on mercury (Hg) speciation and distribution in sediments and cultured fish around Hong Kong and adjacent mainland China waters, sediment samples were collected from six mariculture sites and the corresponding reference sites, 200-300 m away from the mariculture sites. Mariculture activities increased total mercury, organic matter, carbon, nitrogen and sulfur concentrations in the surface sediments underneath mariculture sites, possibly due to the accumulation of unconsumed fish feed and fish excretion. However, methylmercury (MeHg) concentrations and the ratio of MeHg to THg (% MeHg) in sediments underneath mariculture sites were lower than the corresponding reference sites. The % MeHg in sediments was negatively correlated (r = −0.579, p < 0.05) with organic matter (OM) content among all sites, indicating that OM may have inhibited Hg methylation in surface sediments. Three mariculture fish species were collected from each mariculture site, including red snapper (Lutjanus campechanus), orange-spotted grouper (Epinephelus coioides) and snubnose pompano (Trachinotus blochii). The average MeHg concentration in fish muscle was 75 μg kg⁻¹ (wet weight), and the dietary intake of MeHg through fish consumption for Hong Kong residents was 0.37 μg kg⁻¹ week⁻¹, which was lower than the corresponding WHO limits (500 μg kg⁻¹ and 1.6 μg kg⁻¹ week⁻¹).     

Development of a combined isotopic and mass-balance approach to determine dissolved organic carbon sources in eutrophic reservoirs

A combined mass-balance and stable isotope approach was set up to identify and quantify dissolved organic carbon (DOC) sources in a DOC-rich (9 mg L⁻¹) eutrophic reservoir located in Western France and used for drinking water supply (so-called Rophemel reservoir). The mass-balance approach consisted in measuring the flux of allochthonous DOC on a daily basis, and in comparing it with the effective (measured) DOC concentration of the reservoir. The isotopic approach consisted, for its part, in measuring the carbon isotope ratios (δ¹³C values) of both allochthonous and autochthonous DOC sources, and comparing these values with the δ¹³C values of the reservoir DOC. Results from both approaches were consistent pointing out for a DOC of 100% allochthonous origin. In particular, the δ¹³C values of the DOC recovered in the reservoir (−28.5 ± 0.2‰; n = 22) during the algal bloom season (May-September) showed no trace of an autochthonous contribution (δ¹³C in algae = −30.1 ± 0.3‰; n = 2) being indistinguishable from the δ¹³C values of allochthonous DOC from inflowing rivers (−28.6 ± 0.1‰; n = 8). These results demonstrate that eutrophication is not responsible for the high DOC concentrations observed in the Rophemel reservoir and that limiting eutrophication of this reservoir will not reduce the potential formation of disinfection by-products during water treatment. The methodology developed in this study based on a complementary isotopic and mass-balance approach provides a powerful tool, suitable to identify and quantify DOC sources in eutrophic, DOC-contaminated reservoirs.     

Linking chemical extraction to microbial degradation of 14C-hexadecane in soil

Chemical extractions have been shown to measure the biodegradable fraction of aromatic contaminants in soil; however, there is little research on the chemical prediction of aliphatic hydrocarbon degradation. The aim of this study was to investigate the potential for cyclodextrin extractions to predict hexadecane biodegradation in soil. Soils were amended with 10 or 100 mg kg⁻¹ of a model alkane n-hexadecane and 100 Bq g⁻¹¹⁴C-n-hexadecane. Correlations between the extents of mineralisation and extractions of the ¹⁴C-contaminant were determined. Solvent shake extractions and aqueous CaCl₂ extractions were poor predictors of hexadecane bioaccessibility. However, the novel HP-α-CD shake extraction showed close correlation (r² = 0.90, n = 36, p < 0.05) to the mineralisation data. This novel extraction technique has the potential to be used to assess the biodegradable aliphatic hydrocarbon fraction in contaminated soils.     

Occurrence and source characterization of perfluorochemicals in an urban watershed

Perfluorochemicals (PFCs) are used in numerous applications, mainly as surfactants, and occur ubiquitously in the environment as complex mixtures. This study was undertaken to characterize the occurrence and sources of commonly detected PFC compounds in surface waters of the Marina catchment, a watershed that drains an urbanized section of Singapore. Of the 19 target PFCs, 13 were detected with perfluorooctanoic acid (PFOA) (5-31 ng L⁻¹) and perfluorooctane sulfonate (PFOS) (1-156 ng L⁻¹) being the dominant components. Other compounds detected included perfluoroalkyl carboxylates (C7-C12) and perfluoroalkyl sulfonates (C6 and C8). Sulfonamide compounds detected 2-(N-ethylperfluorooctanesulfonamido) acetic acid (N-EtFOSAA), 2-(N-methylperfluorooctanesulfonamido) acetic acid (N-MeFOSAA), perfluorooctanesulfonamido acetic acid (FOSAA) and perfluorooctanesulfonamide (FOSA) were putative transformation products of N-EtFOSE and N-MeFOSE, the N-ethylated and N-methylated ethyl alcohol derivatives, respectively. Surface water concentrations were generally higher during dry weather than during storm water flow: the median concentrations of total PFCs in dry and wet weather were 57 and 138 ng L⁻¹ compared to 42 and 79 ng L⁻¹, respectively, at Stamford and Alexandra canal, suggesting the presence of a continuous source(s) which is subject to dilution during storm events. In rain water, median concentrations were 6.4 ng L⁻¹, suggesting rain contributed from 12-25% to the total PFC load for non-point source sites. The longitudinal concentration profile along one of the canals revealed a point source of sulfonated PFCs (PFOS), believed to originate from aqueous film-forming foam (AFFF). Sources were characterized using principal component analysis (PCA) and by plotting PFHxS/PFOA against PFOS/PFOA. Typical surface waters exhibit PFOS/PFOA and PFHxS/PFOA ratios below 0.9 and 0.5, respectively. PCA plots reveal waters impacted by “non-typical” PFC sources in Alexandra canal.     

Removal capacity and pathways of phenolic endocrine disruptors in an estuarine wetland of natural reed bed

Phenolic compounds are partly known as endocrine disruptors with various harmful effects including feminization and carcinogenesis at very low concentrations. Consequently, the pathways and removal of these compounds in natural and artificial sewage treatment systems such as wetlands have received wide concern. In this paper, a natural reed bed wetland with an area of 695 ha located in the Liaohe River estuary in Northeast China was employed as a demonstration site to study the retention and removal efficiency of phenolic compounds including 4-nonylphenol (4-NP), bisphenol A (BPA), 4-t-octylphenol (4-t-OP), and 2,4-dichlorophenol (DCP), and to evaluate their purification capacity via water and mass balance analyses during an irrigation period from May 9 to September 8, 2009. The results showed that the phenolic compounds could be retained in the wetland system and removed through various processes. On average, 27.5% of phenolic compounds could be retained by the wetland substrate during the initial three-day irrigation period with a retention capacity order of 4-t-OP > 4-NP > BPA > DCP. During the following 120 d irrigation period, the phenolic compounds could be efficiently removed with an average percentage of 91.6%. It is estimated that 1.76 kg d⁻¹ of phenolic compounds could be removed by the Liaohe River estuarine wetland (∼8 × 10⁴ ha). The reed bed wetland system therefore provides a feasible mitigation option for phenolic pollutants in sewage and wastewater.     

Levels of organochlorine pesticides and polychlorinated biphenyls in the critically endangered Iberian lynx and other sympatric carnivores in Spain

Accumulation of organochlorine compounds is well studied in aquatic food chains whereas little information is available from terrestrial food chains. This study presents data of organochlorine levels in tissue and plasma samples of 15 critically endangered Iberian lynx (Lynx pardinus) and other 55 wild carnivores belonging to five species from three natural areas of Spain (Doñana National Park, Sierra Morena and Lozoya River) and explores their relationship with species diet. The Iberian lynx, with a diet based on the consumption of rabbit, had lower PCB levels (geometric means, plasma: <0.01 ng mL⁻¹, liver: 0.4 ng g⁻¹ wet weight, fat: 87 ng g⁻¹ lipid weight) than other carnivores with more anthropic and opportunistic foraging behavior, such as the red fox (Vulpes vulpes; plasma: 1.11 ng mL⁻¹, liver: 459 ng g⁻¹, fat: 1984 ng g⁻¹), or with diets including reptiles at higher proportion, such as the Egyptian mongoose (Herpestes ichneumon; plasma: 7.15 ng mL⁻¹, liver: 216 ng g⁻¹, fat: 540 ng g⁻¹), or the common genet (Genetta genetta; liver: 466 ng g⁻¹, fat: 3854 ng g⁻¹). Chlorinated pesticides showed interspecific variations similar to PCBs. Organochlorine levels have declined since the 80s in carnivores from Doñana National Park, but PCB levels are still of concern in Eurasian otters (Lutra lutra; liver: 3873-5426 ng g⁻¹) from the industrialized region of Madrid.