Radiolytic decomposition of multi-class surfactants and their biotransformation products in sewage treatment plant effluents

Electron beam irradiation (EBI), as one of the most efficient advanced oxidation processes, was applied to the treatment of sewage treatment plant (STP) effluent, with the objective of evaluating the effectiveness of radiolytic decomposition of multi-class surfactants. Target compounds, included several high-volume surfactant groups, such as alkylphenol ethoxylates (APEOs) and their biotransformation products, linear alkylbenzene sulfonates (LAS), alkyl sulfates (AS), alkylether sulfates (AES), coconut diethanol amides (CDEA), alcohol ethoxylates (AEO) and polyethylene glycols (PEGs). EBI treatment of STP effluent (total concentration of APEO-derived compounds 265mugl(-1), being APE(2)C the most abundant by-degradation products) resulted in efficient decomposition of all alkylphenolic compounds; elimination of 94% longer ethoxy chain nonylphenol ethoxylates (NPEO, n(EO)=3-15) was obtained when 3kGy were applied. Slightly less efficient decomposition of short ethoxy chain oligomers (NPEO(1) and NPEO(2)) was observed, resulting in disappearance of about 80% of the initially present compounds. LC-MS analysis of treated wastewater suggested that the mechanism of EBI degradation of APEOs is a combination of two parallel pathways: a progressive shortening and oxidation of the ethoxy chain, which resulted in a formation of short ethoxy chain oligomers and APECs and central fission that resulted in formation of PEGs. Decomposition of APECs at 1kGy initially yielded APs, which were subsequently eliminated applying higher radiation doses. With a radiation dose of 2kGy about 95% of NPE(1)C and 97% of NPE(2)C were decomposed. Similar elimination rates were obtained for octylphenolic compounds. Radiolytic treatment applied was also very effective in removing PEGs formed as by-products from APEO degradation, as well as in decomposing other surfactants, such as linear LAS, AS and AES.     

Peroxymonosulfate-Co(II) oxidation system for the removal of the non-ionic surfactant Brij 35 from aqueous solution

The non-ionic surfactant Brij 35 was effectively removed from concentrated aqueous solution by the peroxymonosulfate/Co(II) system, using oxone (2KHSO₅·KHSO₄·K₂SO₄) as a source of peroxymonosulfate. At pH = 2.3 and initial Brij 35 concentration in the range 680-2410 mg L⁻¹, 86-94% removal was achieved after 24 h, using Co(II) = 15 μM and oxone = 5.9 mM. The effectiveness of removal did not change when initial pH was in the range 2.3-8.2. After five subsequent additions of Co(II) and oxone to the solution, COD and TOC removals increased up to 64% and 33%, respectively. Radical quenching tests confirmed that sulfate radical was the dominant radical species in the system. The main identified by-products from surfactant degradation were: (a) low molecular weight organic acids; (b) aldehydes and formates with shorter ethoxy chain than Brij 35; (c) alcohol ethoxylates carrying hydroxyl groups bonded to ethoxy chain. By-products identification allowed to hypothesize the pathways of Brij 35 degradation.     

Is it possible to remediate a BTEX contaminated chalky aquifer by in situ chemical oxidation?

An industrial coating site in activity located on a chalky plateau, contaminated by BTEX (mainly xylenes, no benzene), is currently remediated by in situ chemical oxidation (ISCO). We present the bench scale study that was conducted to select the most appropriate oxidant. Ozone and catalyzed hydrogen peroxide (Fenton’s reaction) were discarded since they were incompatible with plant activity. Permanganate, activated percarbonate and activated persulfate were tested. Batch experiments were run with groundwater and groundwater-chalk slurries with these three oxidants. Total BTEX degradation in groundwater was reached with all the oxidants. The molar ratios [oxidant]:[Fe²⁺]:[BTEX] were 100:0:1 with permanganate, 100:100:1 with persulfate and 25:100:1 with percarbonate. Precipitation of either manganese dioxide or iron carbonate (siderite) occurred. The best results with chalk slurries were obtained with permanganate at the molar ratio 110:0:1 and activated persulfate at the molar ratio 110:110:1. To avoid precipitation, persulfate was also used without activation at the molar ratio 140:1. Natural Oxidant Demand measured with both oxidants was lower than 5% of initial oxidant contents. Activated percarbonate was not appropriate because of radical scavenging by carbonated media. Permanganate and persulfate were both effective at oxidant concentrations of ca 1 g kg⁻¹ with permanganate and 1.8 g kg⁻¹ with persulfate and adapted to site conditions. Activation of persulfate was not mandatory. This bench scale study proved that ISCO remediation of a chalky aquifer contaminated by mainly xylenes was possible with permanganate and activated or unactivated persulfate.     

Automobile exhaust gas as a source of aqueous phase OH radical in the atmosphere and its effects on physiological status of pine trees

Free radical generation potential of automobile exhaust gas was examined by measuring hydroxyl (OH) radical photo-formation rates in exhaust gas-scrubbing water. Effects of automobile exhausts on physiological status of Japanese red pine trees (Pinus densiflora Sieb. et Zucc.) were also investigated to elucidate the mechanism how the free radicals derived from exhaust gas damage higher plants. Gasoline and diesel exhaust gases were scrubbed into pure water. Potential photo-formation rates of OH radical in aqueous phase (normalized to sun light intensity of clear sky midday on May 1 at 34°N) for gasoline and diesel cars were ave. 51 and 107 μM h⁻¹ m⁻³ of exhaust gas, respectively. Nitrite was a dominant source (ca. 70-90%) of photochemical formation of OH radical in both gasoline and diesel car exhausts. The scrubbed solution of diesel car exhaust gas was sprayed for six times per week to needles of pine tree seedlings in open top chambers. Control, exhaust + mannitol (added as OH radical scavenger), and nitrite + nitrate standard solution (equivalent levels existed in the exhaust gas) were also sprayed. Two months sprays indicated that the sprayed solutions of diesel exhaust and nitrite + nitrate caused a decrease of maximum photosynthetic rate and stomata conductance in pine needles while the control and exhaust + mannitol solution showed no effects on photosynthetic activities of pine needles. These results indicated that OH radicals generated mainly from photolysis of nitrite occurring in the scrubbing solution of exhaust gas are responsible for the decrease of photosynthetic activities of pine needles.     

Epibrassinolide ameliorates Cr (VI) stress via influencing the levels of indole-3-acetic acid, abscisic acid, polyamines and antioxidant system of radish seedlings

The present investigation determined the effects of epibrassinolide (EBL) on the levels of indole-3-acetic acid (IAA), abscisic acid (ABA), and polyamine (PA) and antioxidant potential of 7-d old Raphanus sativus L. cv. ‘Pusa chetki’ seedlings grown under Cr (VI) metal stress. Reduced titers of free (0.767 μg g⁻¹ FW) and bound (0.545 μg g⁻¹ FW) IAA in Cr (VI) stressed seedlings were observed over untreated control. Supplementations of EBL to Cr (VI) stressed seedlings were able to enhance both free (2.14-5.68 μg g⁻¹ FW) and bound IAA (2.45-7.78 μg g⁻¹ FW) concentrations in comparison to Cr (VI) metal treatment alone. Significant rise in free (13.49 μg g⁻¹ FW) and bound (12.17 μg g⁻¹ FW) ABA contents were noticed for Cr (VI) stressed seedlings when compared to untreated control. No significant increase in ABA contents were recorded for Cr (VI) stressed seedlings upon supplementation with EBL over Cr (VI) treatment alone. A significant increase in Put (18.40 μg g⁻¹ FW) and Cad (9.08 μg g⁻¹ FW) contents were found for 10⁻⁹ M EBL plus Cr (VI) metal treatments when compared to Cr (VI) treatment alone. Spermidine (Spd) contents were found to decline significantly for EBL treatment alone or when supplemented with Cr (VI) treatments over untreated controls and Cr (VI) treatment alone. Antioxidant levels were found to enhance, with glutathione (57.98 mg g⁻¹ FW), proline (4.97 mg g⁻¹ FW), glycinebetaine (39.01 μmol mL⁻¹), ascorbic acid (3.17 mg g⁻¹ FW) and phytochelatins (65.69 μmol g⁻¹ FW) contents noted for EBL supplemented to Cr (VI) metal solution over Cr (VI) treatment alone. Reduced activities of guaiacol peroxidase (0.391 U mg⁻¹ protein) and catalase (0.221 U mg⁻¹ protein) and enhanced activities of glutathione reductase (7.14 U mg⁻¹ protein), superoxide dismutase (15.20 U mg⁻¹ protein) and ascorbate peroxidase (4.31 U mg⁻¹ protein) were observed in seedlings treated with EBL plus Cr (VI) over Cr metal treatment alone. Reduced MDA (2.55 μmol g⁻¹ FW) and H₂O₂ (33.24 μmol g⁻¹ FW) contents were recorded for 10⁻⁹ M EBL supplemented to Cr (VI) stress over Cr (VI) treatment alone. Enhancement in free radical scavenging potential as indicated by higher values of 1,1-diphenylpicrylhydrazyl, deoxyribose and reducing power activity assays, and increased levels of phenols and soluble sugars also showed significant influence of EBL in alleviating Cr (VI) stress in radish seedlings.     

Development and calibration of a passive sampler for N-nitrosodimethylamine (NDMA) in water

N-Nitrosamines such as N-nitrosodimethylamine (NDMA) are organic compounds of environmental concern in groundwater, wastewater and potable water due to their potent carcinogenicity in laboratory animal studies and probable human carcinogenicity. While passive sampling techniques have become a widely used tool for providing time-averaged estimates of trace pollutant concentration, for chemicals such as NDMA that have relatively high water solubility, the selection of a suitable sorbent is difficult. This work is a proof of principle study that investigated for the first time the use of coconut charcoal as a passive sampler sorbent. Apparent charcoal/water sorption coefficients for NDMA were >551 mL g⁻¹ at environmentally relevant aqueous concentrations of less than 1 μg L⁻¹. Under the experimental conditions employed, a sampling rate of 0.45 L d⁻¹ was determined and for an aqueous concentration of 1000 ng L⁻¹, it is predicted that the sampler remains in the linear uptake stage for approximately 4 d, while equilibrium attainment would require about 26 d. The presence of humic acid, used as a surrogate for DOC, enhanced NDMA sorption on the coconut charcoal.     

Aqueous free radical chemistry of mercury in the presence of iron oxides and ambient aerosol

The effect of goethite (α-FeOOH), hematite (α-Fe₂0₃) and maghemite (γ-Fe₂0₃) on the aqueous photoreduction of divalent mercury with organic acids (oxalate, formate and acetate) is investigated. Laboratory photochemistry experiments with synthetic iron oxides and simulated sunlight were performed to assess the role of the oxides on the photoreduction. Ambient aerosol was also collected and introduced as the solid phase to compare its effect with that of synthetic oxides. It is observed that the presence of various iron oxides or aerosol particles enhances the photoreduction. It is also found that the hydroxyl radicals produced in the hematite-oxalate systems can re-oxidize the reduced mercury back to Hg(II). Based on the experimental observations, mechanisms responsible for the Hg(II) reduction are proposed. The kinetics of Hg⁰ oxidation by hydroxyl radicals was also studied by a steady-state kinetic technique using nitrate photolysis as the * OH radical source. The second-order rate constant is determined to be 2.0 × 10⁹ M⁻ s⁻¹. The implications of the studied reactions on the atmospheric chemistry of mercury are discussed.     

Concentrations of polychlorinated biphenyls in water from US Lake Ontario tributaries between 2004 and 2008

Research on the environmental fate and transport of PCBs in Lake Ontario basin depends, among other aspects, on the availability of representative data sets for upstream sources, but data are lacking for most US Lake Ontario tributaries. In this study, water samples were collected between September 2004 and October 2008 from five tributaries and were analyzed for 209 polychlorinated biphenyls (PCB) with high-resolution gas chromatography/high resolution mass spectrometry (HRGC/HRMS) following EPA Method 1668A. Total PCB concentrations ranged between 0.31 and 42.75 ng L⁻¹. Congeners between Di and Hexa PCBs accounted between 70 and 99% of the total PCB. The tributary with highest PCB concentrations presented similar pattern and percentage levels to Aroclor 1242. Total average loads for the sampling events ranged between 1.85 g d⁻¹ and 59.08 g d⁻¹. PCB concentrations were evaluated against other variables and other studies (including different matrices) to better understand their transport. The methodology used is reliable to assess PCB contamination in surface water.     

Photolysis of nonylphenol ethoxylates: the determination of the degradation kinetics and the intermediate products

The photolysis of nonylphenol ethoxylates with an average oligomers length of ten ethoxylate units (NPEO(10)) in aqueous solution under UV, as well as the influence of humic acid (HA) on the photolysis was studied. A 125W high-pressure mercury lamp was employed as the light source. The intermediate products from the photolysis were determined by LC-MS. The results indicated that NPEO(10) underwent direct photolysis upon exposed to UV. The degradation pathway was complex. Besides the generally proposed degradation pathway of ethylene oxide (EO) side chains shortening, the oxidation of alkyl chain and EO chain led to intermediates having both a carboxylated (as well as carbonylated) ethoxylate and alkyl chain of varying lengths. The hydrogenation of benzene ring was also detected. The kinetics data showed that the first order reaction kinetics could be well used to describe the kinetics of NPEO(10) degradation. In the presence of dissolved organic matter by HA addition, the performance of NPEO(10) photodegradation was reduced. The photolysis rate decreased with increased HA concentration.     

Use of thermal desorption-gas chromatography-mass spectrometry (TD-GC-MS) on identification of odorant emission focus by volatile organic compounds characterisation

Volatile organic compounds (VOCs) from several different municipal solid wastes’ treatment plants in Mallorca (Spain) have been analysed by thermal desorption-gas chromatography-mass spectrometry (TD-GC-MS). Ambient (immission) air was collected during February and March 2011 by active sampling onto sorbents Tenax™ TA and Carboxen™ 1000. The study presents the chemical characterisation of 93 volatile organic compounds (VOCs) from an overall set of 84 immission air samples. 70 VOCs were positively identified.The linear fit for all 93 external standard calibration, from 10 mg L⁻¹ to 150 mg L⁻¹ (n = 4), was within the range 0.974 < r² < 0.998. Limits of detection of the method (LOD) for all the standards were within the range 1.1-4,213 pg, as the absolute standard amount spiked into sorbent tubes in 1 μL standard mixture (dissolved in methanol).Overall results stated systematic correlation between waste’s nature and VOCs’ air composition. Organic wastes show main contribution of terpenes, waste water sludge residues’ of reduced sulphured compounds (RSCs) and municipal solid wastes show contribution of a wide sort of VOCs. The use of a chemometric approach for variable’s reduction to 12 principal components enables evaluation of similarities and dissimilarities between facilities. PCA clearly related samples to its corresponding facility on the basis of their VOCs composition and the ambient temperature.     

Identification of two new cytochrome P450 genes and RNA interference to evaluate their roles in detoxification of commonly used insecticides in Locusta migratoria

Composite samples of Australian farmed Yellowtail Kingfish (Seriola lalandi) (YTKF) (n = 27), Mulloway (Argyrosomus hololepidotus) (n = 6) and manufactured feed (n = 5) were analysed to benchmark levels of a broad range of residues and contaminants of potential public health and trade significance. A subset of these samples [YTKF (n = 5), Mulloway (n = 2) and feed (n = 5)] was analysed for dioxins and polychlorinated biphenyls (PCBs). The mean concentration of dioxins in YTKF was 0.6 pg TEQ g⁻¹ (range 0.22-0.8) and in Mulloway was 0.16 pg TEQ g⁻¹ (range 0.16-0.16). The mean concentration of dioxins and dioxin-like PCBs in YTKF was 2.6 pg TEQ g⁻¹ (range 1.4-3.5), while Mulloway had a mean concentration of 0.67 pg TEQ g⁻¹ (range 0.57-0.76). The mean concentration of PCBs in YTKF was 21 μg kg⁻¹ (range 8.6-29) and in Mulloway was 5.4 μg kg⁻¹ (mean 4.7-6). The mean concentration of dioxin-like PCBs in YTKF was 2.1 pg TEQ g⁻¹ (range 1.2-2.8) and in Mulloway was 0.51 pg TEQ g⁻¹ (range 0.41-0.61). The mean mercury concentration in YTKF was 0.03 mg kg⁻¹ (range 0.02-0.05) and in Mulloway it was 0.02 mg kg⁻¹ (range 0.02-0.04). There were no detectable levels of any pesticide or antimicrobial compounds in any sample of YTKF or Mulloway. Attention is drawn to technical differences in port of entry testing programs such as sampling strategies, portion tested, laboratory methodology, residue definitions and reporting conventions that exporters’ products may be subject to. All residues and contaminants were either undetectable or present at very low levels when judged against Australian, Japanese and European Union regulatory standards (where set).     

Nitrate-induced photodegradation of atenolol in aqueous solution: kinetics, toxicity and degradation pathways

The extensive utilization of β-blockers worldwide led to frequent detection in natural water. In this study the photolysis behavior of atenolol (ATL) and toxicity of its photodegradation products were investigated in the presence of nitrate ions. The results showed that ATL photodegradation followed pseudo-first-order kinetics upon simulated solar irradiation. The photodegradation was found to be dependent on nitrate concentration and increasing the nitrate from 0.5 mM L⁻¹ to 10 mM L⁻¹ led to the enhancement of rate constant from 0.00101 min⁻¹ to 0.00716 min⁻¹. Hydroxyl radical was determined to play a key role in the photolysis process by using isopropanol as molecular probe. Increasing the solution pH from 4.8 to 10.4, the photodegradation rate slightly decreased from 0.00246 min⁻¹ to 0.00195 min⁻¹, probably due to pH-dependent effect of nitrate-induced OH formation. Bicarbonate decreased the photodegradation of ATL in the presence of nitrate ions mainly through pH effect, while humic substance inhibited the photodegradation via both attenuating light and competing radicals. Upon irradiation for 240 min, only 10% reduction of total organic carbon (TOC) can be achieved in spite of 72% transformation rate of ATL, implying a majority of ATL transformed into intermediate products rather than complete mineralization. The main photoproducts of ATL were identified by using solid phase extraction-liquid chromatography-mass spectrometry (SPE-LC-MS) techniques and possible nitrate-induced photodegradation pathways were proposed. The toxicity of the phototransformation products was evaluated using aquatic species Daphnia magna, and the results revealed that photodegradation was an effective mechanism for ATL toxicity reduction in natural waters.     

The association between total urinary arsenic concentration and renal dysfunction in a community-based population from central Taiwan

Arsenic (As) is an important environmental toxicant that can cause cancer and cardiovascular disease, but the relationship between As exposure and renal dysfunction is not clear. The aim of this study is to examine the association between As exposure and renal dysfunction in a community-based population in central Taiwan. One thousand and forty-three subjects were recruited between 2002 and 2005. The risk for type 2 diabetes was increased by 2-fold (p < 0.05) in subjects with total urinary As (U-As) > 75 μg g⁻¹ creatinine as compared with subjects whose U-As was ?35 μg g⁻¹ creatinine after the adjustment for potential confounders. The adjusted odds ratio for an abnormal β2 microglobulin (B2MG > 0.154 mg L⁻¹) was significantly higher in subjects with U-As > 35 μg g⁻¹ creatinine as compared with the reference group adjusted for age, sex, living area, cigarette smoking, diabetes, and hypertension. The risk for abnormal B2MG and estimated glomerular filtration rate (eGFR < 90 mL min⁻¹ (1.73 m²)⁻¹) was both increased around 2-fold (p < 0.05) in subjects with U-As > 75 μg g⁻¹ creatinine as compared with those with U-As ? 35 μg g⁻¹ creatinine adjusted for all the risk factors plus lead (Pb), cadmium and nickel. The prevalence of abnormal B2MG was 4.82 times higher in subjects with both over the median levels of U-As (85.1 μg L⁻¹) and urinary Pb (18.9 μg L⁻¹) as compared to both lower than the median (p < 0.001). These results indicate that U-As might relate to renal dysfunction even other important risk factors were taken into account. Follow-up studies for causal inference are warranted.     

Monitoring and modelling of siloxanes in a sewage treatment plant in the UK

Monitoring of cyclic volatile methylsiloxanes (cVMS) carried out at Anglian Water’s Broadholme sewage treatment plant (STP) is described. The method deployed used headspace gas chromatography/mass spectrometry (HS-GC/MS) and the addition of isotopically labelled cVMS to correct for partitioning in samples containing high levels of particulate and dissolved organic carbon. The method was capable of measuring cVMS in raw sewage samples, with recoveries of 80%, 85% and 71% respectively, for D₄, D₅ and D₆. The limit of quantification was 0.2 μg L⁻¹ for all three substances. Recoveries close to 100% were observed for all cVMS spiked into treated effluent (LOQ = 0.01 μg L⁻¹). Despite the volatile nature of cVMS and its ubiquitous presence in the ambient atmosphere, the methods deployed showed excellent recoveries, reproducibility and quantification limits. A distinct diurnal variation in cVMS concentration, probably linked with the use of personal care products was observed for raw sewage but not in treated sewage effluent. The estimated per capita consumption of D₅ (∼2.7 mg cap⁻¹ d⁻¹) derived for the population served by this plant was significantly lower than that derived in the Environment Agency (UK) risk assessment (11.6 mg cap⁻¹ d⁻¹). The cVMS were highly removed during sewage treatment with efficiencies greater than 98%. The methods and findings of this pilot study can be used as the basis for future studies on the fate of cVMS substances in STPs.     

The arrival and discharge of conjugated estrogens from a range of different sewage treatment plants in the UK

The occurrence of free and conjugated estrogens was examined in a survey of eleven sewage treatment plants (STPs) and their discharge water in the United Kingdom using grab sampling. The STPs included trickling filter with and without tertiary treatment, and activated sludge with tertiary treatment. For three activated sludge plants both influent and effluent samples were compared. For a further 8 STPs only the effluent was examined. The estrone-3-sulphate, estradiol-3-sulphate and estriol-3-sulphate concentrations (up to 20 ng L⁻¹) were typically 5-fold that of the respective free estrogen concentration in the effluents. This represents a substantial additional ‘potential’ estrogen load arriving in the receiving waters. Estrone-3-glucuronide was found at 9 ng L⁻¹, estradiol-3-glucuronide at 7 ng L⁻¹, and estriol-3-glucuronide at 32 ng L⁻¹ in sewage influent. Except on one occasion, no glucuronide conjugates could be found in the effluent. The results suggest in most cases glucuronide conjugates will be completely transformed in sewage treatment whilst sulphate conjugates will only be partially removed.     

Photolytic and photocatalytic degradation of 6-chloronicotinic acid

This work describes for the first time the photolytic and photocatalytic degradation of 6-chloronicotinic acid (6CNA) in double deionised water, which is a degradation product of neonicotinoid insecticides imidacloprid and acetamiprid, and it is known to appear in different environmental matrices. Photolytic experiments were performed with three UVA (ultraviolet A) polychromatic fluorescent lamps with broad maximum at 355 nm, while photocatalytic experiments were performed using immobilised titanium dioxide (TiO₂) on six glass slides in the spinning basket inside a photocatalytic quartz cell under similar irradiation conditions. Photolytic degradation revealed no change in concentration of 6CNA within 120 min of irradiation, while the photocatalytic degradation within 120 min, obeyed first-order kinetics. The observed disappearance rate constant was k = 0.011 ± 0.001 min⁻¹ and t_1/2 was 63.1 ± 5.5 min. Mineralisation rate was estimated through total organic carbon (TOC) and measurements revealed no carbon removal in case of photolysis after 120 min of exposure. However in photocatalytic experiments 46 ± 7% mineralisation was achieved within 120 min of irradiation. Nevertheless, the removal of total nitrogen (TN) was not observed across all experiments. Ion chromatographic analyses indicated transformation of chlorine atoms to chloride and increase of nitrate(V) ions only via photocatalytic experiments. Efficiency of selected advanced oxidation process (AOP) was investigated through toxicity assessment with Vibrio fischeri luminescent bacteria and revealed higher adverse effects of treated samples on bacteria following photocatalytic degradation in spite of the fact that higher mineralisation was achieved. New hydroxylated product generated in photocatalytic experiments with TiO₂, was confirmed with liquid chromatography-electro spray ionisation mass spectrometry (LC-ESI-MS/MS) analyses, gas chromatography-mass spectrometry (GC-MS) and nuclear magnetic resonance spectroscopy (¹H NMR).     

Separation of dissolved iron from the aqueous system with excess ligand

A new technique for the separation and pre-concentration of dissolved Fe(III) from the ligand-rich aqueous system is proposed. A solid phase extraction (SPE) system with an immobilized macrocyclic material, commonly known as molecular recognition technology (MRT) gel and available commercially, was used. Synthetic Fe(III) solution in aqueous matrices spiked with a 100-fold concentration of EDTA was used. Dissolved iron that was ‘captured’ by the MRT gel was eluted using hydrochloric acid and subsequently determined by graphite furnace atomic absorption spectrometry. The effect of different variables, such as pH, reagent concentration, flow rate and interfering ions, on the recovery of analyte was investigated. Quantitative maximum separation (∼100%) of the dissolved Fe(III) from synthetic aqueous solutions at a natural pH range was observed at a flow rate of 0.2 mL min^-1. The extraction efficiency of the MRT gel is largely unaltered by the coexisting ions commonly found in natural water. When compared with different SPE materials, the separation performance of MRT gel is also much higher.     

Exposure assessment of French women and their newborn to brominated flame retardants: determination of tri- to deca- polybromodiphenylethers (PBDE) in maternal adipose tissue, serum, breast milk and cord serum

In the frame of a French monitoring program, tri- to deca- polybromodiphenylethers (PBDE) have been measured in maternal and cord serum, adipose tissue, and breast milk samples, collected from 93 volunteer women during caesarean deliveries. The seven major tri- to heptaBDE (BDE-28, 47, 99, 100, 153, 154, and 183) were detected in adipose tissue and breast milk with cumulated median values of 2.59 and 2.51 ng g⁻¹ l w. Nine highly brominated octa- to decaBDE (BDE-196, 197, 201, 202, 203, 206, 207, 208 and 209) was performed in the same samples, with cumulated median values of 2.73 and 3.39 ng g⁻¹ l w in adipose tissue and breast milk, respectively. At this opposite, median levels of octa- to decaBDE in maternal and cord serum appeared significantly higher than the levels of tri- to heptaBDE in the same matrices, i.e. 8.85 and 12.34 versus 0.98 and 0.69 ng g⁻¹ l w, respectively.