Enhancement of batch waste activated sludge digestion by microwave pretreatment.

Batch anaerobic digesters were used to stabilize microwave (MW)-irradiated waste activated sludge (WAS). A low temperature range (50-96 degrees C) MW irradiation was applied. Effects of pretreatment temperature (T) and intensity (I), concentration (C) and percentage of sludge pretreated (PT) were investigated in a multilevel factorial statistical design containing 54 mesophilic batch reactors by monitoring cumulative biogas production (CBP). Variance analysis (ANOVA) determined that the most important factors affecting WAS solubilization were temperature, intensity, and sludge concentration. Improvements in CBP from WAS were significantly affected by sludge percentage pretreated, temperature, and concentration. Pretreatment resulted in 3.6 +/- 0.6 and 3.2 +/- 0.1 fold increases in soluble to total chemical oxygen demand (SCOD/TCOD) at high and low sludge concentrations, respectively. WAS, microwaved to 96 degrees C, produced the greatest improvement in CBP with 15 +/- 0.5 and 20 +/- 0.3% increases over controls after 19 d of digestion at low and high WAS concentrations. Dewaterability of microwaved sludge was enhanced after anaerobic digestion.     

剩余污泥发酵产酸特征及基质释放规律研究

剩余污泥发酵既能实现污泥减量,又能获得污水生物脱氮除磷所需的挥发性脂肪酸VFAs等。采用序批式污泥发酵实验,在(30±1)℃的条件下,研究剩余污泥投配比对序批式污泥发酵系统污泥减量、产酸以及基质释放过程的影响,探索VFAs生成最大化的条件。实验结果表明:投加接种污泥不能明显提高序批式污泥发酵系统剩余污泥的减量效果,但可以改善污泥的产酸特性;当污泥投配比大于50%时,发酵过程中将出现2个VFAs浓度峰,且第二次峰浓度更大;较为理想的序批式污泥发酵投配比是60%~80%、发酵时间为5 d或25 d,前者VFAs表观转化率最大(约24%),后者发酵液中VFAs浓度最高(约600 mg/L);发酵过程中,NH4+-N总体呈上升趋势,磷浓度发酵5 d时达到最大值。     

Laboratory evaluation of thermophilic-anaerobic digestion to produce Class A biosolids. 1. Stabilization performance of a continuous-flow reactor at low residence time.

There is increasing interest in the United States in producing biosolids from municipal wastewater treatment that meet the criteria for Class A designation established by the U.S. Environmental Protection Agency. Class A biosolids are intended to be free of pathogens and also must meet requirements for reduction of the vector-attraction potential associated with untreated sludge. High-temperature processes are considered to produce Class A biosolids if the combination of operating temperature and treatment time exceeds minimum criteria, but this option is not applicable to mixed, continuous-flow reactors. Such reactors, or any combination of reactors that does not meet the holding time requirement at a specific temperature, must be demonstrated to inactivate pathogens to levels consistent with the Class A criteria. This study was designed to evaluate pathogen inactivation by thermophilic anaerobic digestion in a mixed, continuous-flow reactor followed by batch or plug-flow treatment. In this first of a two-part series, we describe the performance of a continuous-flow laboratory reactor with respect to physical and chemical operating parameters; microbial inactivation in the combined continuous-flow and batch treatment system is described in the second part. Sludges from three different sources were treated at 53 degrees C, while sludge from one of the sources was also treated at 55 and 51 degrees C. Relatively short hydraulic retention times (four to six days) were used to represent a conservative operating condition with respect to pathogen inactivation. Treatment of a fermented primary sludge led to an average volatile-solids (VS) destruction efficiency of 45%, while VS destruction for the other two sources was near or below 38%, the Class A criterion for vector attraction reduction. Consistent with other studies on thermophilic anaerobic digestion of sludges at short residence times, effluent concentrations of volatile fatty acids (VFAs) were relatively high. Also consistent with other studies, the most abundant VFA in the effluent was propionate. Gas production ranged from 0.3 to 0.5 m3/kg VS fed and from 0.8 to 1.3 m3/kg VS destroyed.     

Metal stabilization mechanism of incorporating lead-bearing sludge in kaolinite-based ceramics

The feasibility and mechanism of incorporating simulated lead-laden sludge into low-cost ceramic products was investigated by observing the reaction of lead with two kaolinite-based precursors under sintering conditions. To investigate the phase transformation process of lead, lead oxide (PbO) mixed with a kaolinite or mullite precursor were fired at 500-950 °C for 3 h. Detailed X-ray diffraction analysis of sintered products revealed that both precursors had crystallochemically incorporated lead into the lead feldspar (PbAl₂Si₂O₈) crystalline structure. By mixing lead oxide with kaolinite, lead feldspar begins to crystallize at 700 °C; maximum incorporation of lead into this structure occurred at 950 °C. However, two intermediate phases, Pb₄Al₄Si₃O₁₆ and a polymorph of lead feldspar, were detected at temperatures between 700 and 900 °C. By sintering lead oxide with the mullite precursor, lead feldspar was detected at temperatures above 750 °C, and an intermediate phase of Pb₄Al₄Si₃O₁₆ was observed in the temperature range of 750-900 °C. This study compared the lead leachabilities of PbO and lead feldspar using a prolonged leaching test (at pH 2.9 for 23 d) modified from the toxicity characteristic leaching procedure. The results indicate the superiority of lead feldspar in stabilizing lead and suggest a promising and reliable strategy to stabilize lead in ceramic products.     

The effect of Mg<Superscript>2+</Superscript> on digestion performance and microbial community structures in sludge digestion systems

The important criteria in anaerobic digestion is the rate-limiting step which decides the fate of value-added products especially from waste-activated sludge (WAS). Hence, the present study investigated the effect of magnesium (Mg²⁺) addition on anaerobic digestion of WAS. The lab-scale experiments were conducted at 25 °C with Mg²⁺ doses ranging from 0.01 to 0.2 mol/L. Maximum total volatile fatty acids (VFAs) production (372.78 mg COD/L) occurred at a Mg²⁺ dose of 0.2 mol/L, which was about eight times higher than the control tests. Further, Mg²⁺ addition facilitated sludge dewaterability and phosphorus removal. The mechanism of improved VFAs generation was analyzed from the view of both chemical and biological effects. Chemical effect significantly enhanced the release of calcium and iron in WAS, resulting in the disintegration of WAS, which benefited hydrolysis and acidification processes. Illumina MiSeq sequencing analysis revealed that enrichment of functional bacteria and the increase of bacterial diversity were obtained in the 0.2 mol Mg²⁺/L experiment, while the influence was negative on the reactor with 0.025 mol/L Mg²⁺. Meanwhile, methanogens were accordantly inhibited in the experiments with Mg²⁺ addition.     

内循环厌氧反应器的启动及影响因素

采用内循环(IC)厌氧反应器,以生产淀粉和酒精的混合废水为处理对象,研究了中温条件下IC反应器的启动及影响因素。结果表明:接种厌氧消化污泥进行培养,逐渐提高进水有机负荷,运行105 d后,可实现IC反应器的启动;当进水COD浓度为11 500 mg/L,有机容积负荷为6.13 kg COD/(m3·d),COD去除率能到达95%左右;水力停留时间对启动过程没有影响,而温度和温度波动影响COD去除率;VFA比pH更能准确快速地反眏出反应器内部环境的变化,防止反应器的酸化;反应器内污泥实现颗粒化,并且具有良好的沉降性。     

Factors affecting the growth rates of ammonium and nitrite oxidizing bacteria

The maximum specific growth rates of both ammonium oxidizing bacteria (AOB) and nitrite oxidizing bacteria (NOB) were investigated under varying aerobic solids retention time (SRT_a) and in the presence/absence of anoxic (alternating) conditions. Two bench SBRs, reactor R1 and R2, were run in parallel for 150 d. Reactor R1 was operated in aerobic conditions while R2 operated in alternating anoxic/aerobic conditions. The feed (synthetic wastewater), temperature, hydraulic retention time and mixing were identical in both reactors. The SRT_a in both reactors was, sequentially, set at four values: 5, 4, 3 and 2 d.Kinetic tests with the biomasses from both reactors were carried out to estimate the maximum specific growth rates (μ_max) at each tested SRT_a and decay rates, in both aerobic and anoxic conditions. The kinetic parameters of nitrifier were estimated through the calibration of a two step nitrification-denitrification activated sludge model.The results point to a slightly higher μ_max,AOB and μ_max,NOB in alternating conditions, while both μ_max,AOB and μ_max,NOB were shown not to vary in the tested range of SRT_a (from 2 to 5 d) at 20 °C. They were relatively high when compared to literature data: 1.05 d⁻¹ < μ_max,AOB < 1.4 d⁻¹ and 0.91 d⁻¹ < μ_max,NOB < 1.31 d⁻¹. The decay coefficients of both AOB and NOB were much higher in aerobic (from 0.22 d⁻¹ to 0.28 d⁻¹) than in anoxic (0.04 d⁻¹ to 0.16 d⁻¹) conditions both in R1 and R2, which explained the higher nitrification rates observed in the alternating reactor.     

An assessment of the feasibility of employing biochemical acidogenic potential tests for characterizing anaerobic biodegradability of raw and pretreated waste activated sludge

The potential to use the results of biochemical acid potential (BAP) tests to predict the ultimate digestibility of raw and pretreated waste activated sludge (WAS) was investigated. The ultimate methane production from biochemical methane potential (BMP) tests on raw and pretreated samples which spanned a range of biodegradability proved linearly related to the volatile fatty acid (VFA) and soluble chemical oxygen demand (COD) production in corresponding BAP tests. In addition, a linear relationship between NH4-N production in the BMP and BAP tests was observed. Despite the linear nature of the relationships, the ratio of the production of methane in the BMP tests to the production of VFAs in the BAP tests varied with the biodegradability of the sludge samples. Waste Activated Sludge samples with low digestibility had ultimate yields of CH4 that were greater than the VFA yields in BAP tests, whereas sludge samples with high digestibility had lower yields of CH4 than the corresponding VFA yields. This trend contrasted with the NH4 results, in which the yields in the BAP tests were consistently less than those observed in the BMP tests. It was hypothesized that the varying relationship between CH4 and VFA yields was because of the inhibition of anaerobic oxidation of long-chain fatty acids (LCFAs) in the BAP tests. Long-chain fatty acids would be converted to CH4 in BMP tests but produced as digestion intermediates in the BAP tests and were not measured as part of the VFA yield. Hydrogen and acetate were identified as the two most likely intermediates that would accumulate in the BAP tests (which would cause inhibition). A stoichiometric model to facilitate the development of an improved understanding of the biodegradation processes in the BAP and BMP tests was assembled. When the model was applied to the BAP tests the anaerobic oxidation of LCFAs and propionate and methanogenesis were excluded from the model. The model was employed to estimate the extent of degradation of lipids, carbohydrates, and proteins in the batch tests as a function of the ultimate biodegradability of the sludge samples. On the basis of model fitting, it was determined that the degradation of lipids in BMP tests decreased, whereas the degradation of carbohydrates and proteins increased as the digestibility of the sludge samples increased. The varying ratio of lipid to protein and carbohydrate degradability with increasing digestibility of the sludge samples describes the relationship between VFA production and CH4 production in the BAP, and BMP tests, respectively.     

挥发性脂肪酸对厌氧干式发酵产甲烷的影响

为了提高中温干式厌氧间歇发酵效率,研究了发酵过程中间产物———挥发性脂肪酸对产甲烷的影响。实验分2批进行,第1批在牛粪发酵过程中分别添加乙酸、丙酸和丁酸,第2批发酵添加易产生挥发酸的厨余垃圾混合发酵。结果显示,添加单一挥发酸的发酵过程中,添加丙酸的产甲烷速度较慢,因为丙酸降解生成乙酸的速度较慢,减慢了甲烷的形成;混合发酵过程厨余垃圾产甲烷速度比牛粪快,发酵过程产生2个产气高峰;牛粪和厨余垃圾固体物质含量比在11∶1到5∶1范围内较好,比牛粪单独发酵产气多,产酸高但不酸败,产生的挥发酸主要是乙酸和丙酸,其中比例为7∶1混合发酵的产甲烷速率最大,为4.89 mL/(g VS·d)。实验表明,牛粪厌氧干式发酵过程添加一定量的厨余垃圾可加快挥发酸的产生并提高挥发酸产量,从而提高甲烷的产量,但是总挥发酸长时间超过10 000 mg/L,pH降到不适于产甲烷菌生长的范围时,将抑制甲烷的生成,挥发酸积累导致厌氧发酵酸败。     

Identification of surfactants emerged in aerobic granulation

In this study, aerobic granules were cultivated in sequencing batch reactors with activated sludge as the seed. The reactors were operated for 12 h per cycle with the organic loading rate (OLR) increasing in double stepwise from 0.5 to 4.0 g COD L⁻¹ d⁻¹. Within the 40 d running, black granules with regular and smooth morphology were cultivated, which had high wet density and high settling velocity. During the granulation process, foams emerged and disappeared in the reactor, coinciding with the proliferation of filamentous microorganisms in the granules, implying that surfactants might exist and play an important role in the granulation. Using ultra performance liquid chromatography-tandem mass spectrometry, the surfactants were identified as homologous compounds of polyethylene glycol (PEG) with molecular weights ranging mainly from 100 to 500 Da. Their general formulas were proposed as HO-[CH₂-CH₂-O]_n-H. The source of PEG still needs further investigation.     

Influence of constant and fluctuating temperature on biodegradation rates of fish biodiesel blends contaminating Alaskan sand

Bioremediation of sandy soil contaminated with fish-biodiesel, conventional diesel, and blends of both was studied in microcosm experiments at different temperatures, simulating the subarctic environment. While distinct lag, exponential, and stationary phases were observed at 20 °C, degradation at 6 °C was slow and the lag phase continued throughout the 4-week experiment. A three-phase 1st order kinetic model successfully described respiration at 20 °C, a one-phase model was sufficient at 6 °C. For temperatures fluctuating between ∼6 and ∼20 °C, higher than expected microbial activity persisted at 6 °C for several days, due to the presence of active cultures, even though the soil temperature closely followed the air temperature. At 20 °C, respiration peaked already after 1 week, and 18-51% of the initially added fuel was mineralized within 4 weeks, whereby degradation was higher at higher biodiesel percentages. Biodiesel addition accelerated mineralization of blends with regular diesel beyond expectations. In blends with 20% biodiesel, the degradation rate constant was twice as high as for conventional diesel. These synergistic effects are likely due to an active microbial population. Addition of biodiesel to conventional diesel could reduce the impact of diesel spills.     

Supercritical water oxidation of tannery sludge: Stabilization of chromium and destruction of organics

The supercritical water oxidation (SCWO) of industrial tannery sludge was investigated to understand the simultaneous destruction of organic pollutants and recovery of high content chromium. Experiments were performed in a batch reactor at temperatures of 350–500 °C, reaction time of 150–300 s and different oxygen ratios, to exhibit the effect of operation conditions. Results showed that removal efficiency of chemical oxygen demand (COD) increased with higher temperature, larger oxidant amount and reaction time; a maximum value of 96% was obtained. Meanwhile, destruction yield was much higher under supercritical conditions than that in subcritical water. In addition, removal efficiency of Cr from sludge reached more than 98% under all conditions; higher temperature played a positive role. Further, leaching toxicity tests of heavy metals in solid products were conducted based on toxicity characteristic leaching procedure. All heavy metals except nickel showed a greatly reduced leaching toxicity through their stabilization. The chromium oxide recovered in ash was amorphous below 550 °C, so that the structure of Cr could not be identified by X-ray diffraction pattern. Special attention should be paid on nickel as its leaching toxicity increased due to the corrosion of reactor surface under severe reaction conditions.     

Biodegradation behavior of agricultural pesticides in anaerobic batch reactors

This study explored the biodegradation potential of two agricultural pesticides (2,4-D and isoproturon) as well as their effect on the performance of the anaerobic digestion process. Three 3.5 L batch reactors were used, having the same initial isoproturon concentration (25 mg/L) and different 2,4-D concentrations (i.e. 0, 100, or 300 mg/L, respectively). All systems were fed with equal amounts of primary sludge and digested sludge and operated at the low mesophilic range (32 ± 2°C). Following an acclimation period of approximately 30 days, complete 2,4-D removal was achieved, whereas isoproturon biodegradation was practically negligible. The presence of 2,4-D did not have a direct effect on acidogenesis since soluble organic carbon [expressed either as volatile fatty acids (VFAs) or as total organic carbon (TOC)] peaked within the first 10 days of operation in all bioreactors. Utilization of VFAs however appeared to follow two distinct patterns: one pattern was represented by acetate and butyrate (i.e. no acid accumulation) while the other was followed by propionate, isobuturate, valerate and isovalerate (i.e. acid accumulation, duration of which was related to the initial 2,4-D concentration). On the whole, all reactors exhibited a successful digestion performance demonstrated by complete VFAs utilization, considerable gas production (containing 45 to 65% methane by volume), substantial volatile suspended solids (VSS) reduction (42 to 50%), as well as pH and alkalinity recovery.     

Influence of the organic loading rate on the performance and the granular sludge characteristics of an EGSB reactor used for treating traditional Chinese medicine wastewater

The effects of the organic loading rate (OLR) on the performance and the granular sludge characteristics of an expanded granular sludge bed (EGSB) reactor used for treating real traditional Chinese medicine (TCM) wastewater were investigated. Over 90 % of the COD removal by the EGSB reactor was observed at the OLRs of 4 to 13 kg COD/(m³ day). However, increasing the OLR to 20 kg COD/(m³ day) by reducing the hydraulic retention time (HRT 6 h) reduced the COD removal efficiency to 78 %. The volatile fatty acid (VFA) concentration was 512.22 mg/L, resulting in an accumulation of VFAs, and propionic acid was the main acidification product, accounting for 66.51 % of the total VFAs. When the OLR increased from 10 to 20 kg COD/(m³ day), the average size of the granule sludge decreased from 469 to 258 μm. There was an obvious reduction in the concentration of Ca²⁺ and Mg²⁺ in the granular sludge. The visible humic acid-like peak was identified in the three-dimensional excitation-emission matrix (EEM) fluorescence spectra of the soluble microbial products (SMPs). The fatty acid bond, amide II bond, amide III bond, and C–H bond bending were also observed in the Fourier transform infrared (FTIR) spectra of the SMPs. Methanobacterium formicicum, Methanococcus, and Bacteria populations exhibited significant shifts, and these changes were accompanied by an increase in VFA production. The results indicated that a short HRT and high OLR in the EGSB reactor caused the accumulation of polysaccharides, protein, and VFAs, thereby inhibiting the activity of methanogenic bacteria and causing granular sludge corruption.     

Fluorescence-based monitoring of tracer and substrate distribution in an UASB reactor

In this work, rhodamine-related fluorescence was measured on-line at four reactor heights in order to study hydrodynamics within an upflow anaerobic sludge bed reactor. A linear dependence of the dispersion coefficient (D) on the upflow velocity was observed, while the influence of the organic loading rate (OLR) was insignificant. Furthermore, the Bodenstein number of the reactor loaded with granulated sludge was found to be position-dependent with the largest values measured at the bottom of the sludge bed. This trend was not observed in the reactor without sludge. Chemical oxygen demand (COD) and volatile fatty acid (VFA) concentrations were measured at the same reactor heights as in rhodamine tests using conventional off-line analytical methods and on-line multiwavelength fluorometry. Significant spatial COD and VFA gradients were observed at organic loading rates above 6g COD l(R)(-1)d(-1) and linear upflow velocities below 0.8m h(-1).     

稻秆负荷与pH对稻秆厌氧发酵产酸系统启动过程的影响

为探讨稻秆负荷（即稻秆VS/污泥VSS）与发酵pH对稻秆厌氧发酵产酸系统启动过程产挥发性脂肪酸（VFAs）效果的影响,利用厌氧搅拌罐反应系统考察在不同的稻秆负荷（0.556、0.945、1.334和1.724 g/g）和不同的发酵pH（8.0、9.0和10.0）启动运行条件下的产酸性能,并分析了系统启动过程产酸与稻秆主要成分降解之间的关系。实验结果表明,VFAs浓度随稻秆负荷提高而增大,随发酵pH的升高而降低;发酵18 d时,发酵pH为9.0时,稻秆负荷1.334 g/g的产酸效果最好,VFAs浓度与稻秆产酸量分别为4 385.10 mg/L和2.19 gVFAs/g稻秆,此时半纤维素、纤维素和酸性洗涤木质素降解率分别为32.69%、22.53%和6.40%;稻秆负荷为0.945 g/g条件下,VFAs浓度在pH为8.0时达到最高值4 409.51 mg/L,此时稻秆降解量也最多,半纤维素、纤维素和酸性洗涤木质素降解率分别为28.60%、47.32%和22.69%。研究表明,稻秆负荷与发酵pH通过影响稻秆半纤维素、纤维素和木质素的降解影响稻秆厌氧发酵产酸的进程和效果。     

Combined effects of deltamethrin, temperature and salinity on oxidative stress biomarkers and acetylcholinesterase activity in the black tiger shrimp (Penaeus monodon)

This study aimed to investigate the interactions of two abiotic factors (temperature and salinity) and deltamethrin (pyrethroid pesticide) exposure on some oxidative stress biomarkers as well as on acetylcholinesterase activity (AChE) in hepatopancreas, gills and muscle of black tiger shrimp (Penaeus monodon). A combination of three temperatures (24, 29 and 34 °C), two salinities (15 and 25 ppt), and the absence or presence of 0.1 μg L⁻¹ deltamethrin was applied on shrimp during 4 d under laboratory conditions. Lipid peroxidation level (LPO) and glutathione S-transferase activity (GST) were not affected by combined effect of temperature, salinity and deltamethrin in any of the studied tissues. Deltamethrin impaired other tested oxidative stress biomarkers, i.e. total glutathione (tGSH), catalase (CAT), glutathione peroxidase (GPx). tGSH level significantly increased in hepatopancreas due to deltamethrin exposure mainly at 34 °C, while pesticide effects on tGSH and CAT activity in gills were influenced by both temperature and salinity. In addition, GPx activity in hepatopancreas decreased after deltamethrin treatment mainly at 24 °C. Finally, AChE in muscle was strongly inhibited by deltamethrin at all tested temperatures and salinities. These novel findings demonstrate that interactions between abiotic factors and a commonly used pesticide exposure should be taken into account when analyzing some widespread biomarkers in black tiger shrimp.     

Biodegradation behavior of agricultural pesticides in anaerobic batch reactors

This study explored the biodegradation potential of two agricultural pesticides (2,4-D and isoproturon) as well as their effect on the performance of the anaerobic digestion process. Three 3.5 L batch reactors were used, having the same initial isoproturon concentration (25 mg/L) and different 2,4-D concentrations (i.e. 0, 100, or 300 mg/L, respectively). All systems were fed with equal amounts of primary sludge and digested sludge and operated at the low mesophilic range (32 +/- 2 degrees C). Following an acclimation period of approximately 30 days, complete 2,4-D removal was achieved, whereas isoproturon biodegradation was practically negligible. The presence of 2,4-D did not have a direct effect on acidogenesis since soluble organic carbon [expressed either as volatile fatty acids (VFAs) or as total organic carbon (TOC)] peaked within the first 10 days of operation in all bioreactors. Utilization of VFAs however appeared to follow two distinct patterns: one pattern was represented by acetate and butyrate (i.e. no acid accumulation) while the other was followed by propionate, isobuturate, valerate and isovalerate (i.e. acid accumulation, duration of which was related to the initial 2,4-D concentration). On the whole, all reactors exhibited a successful digestion performance demonstrated by complete VFAs utilization, considerable gas production (containing 45 to 65% methane by volume), substantial volatile suspended solids (VSS) reduction (42 to 50%), as well as pH and alkalinity recovery.     

Characterization of eco-cement paste produced from waste sludges

In this study, marble sludge, sewage sludge, drinking water treatment plant sludge, and basic oxygen furnace sludge were used as replacements for limestone, sand, clay, and iron slag, respectively, as the raw materials for the production of cement in order to produce eco-cement. It was found that it is feasible to use marble sludge to replace up to 50% of the limestone and also that other materials can serve as total replacements for the raw materials typically used in the production of cement. The major components of Portland cement were all found in eco-cement clinkers. The eco-cement was confirmed to produce calcium hydroxide and calcium silicate hydrates during the hydration process, increasing densification with the curing age. The compressive strength (S_c) and microstructural evaluations conducted at 28 d revealed the usefulness of eco-cement. It was observed that the S_c data correlated linearly with the pore volume (P) data at 28 d. The proposed model equation could be represented as S_c = 178-461P (correlation coefficient, R² = 0.96). Two parameters, the large capillary pore volume and the medium capillary pore volume, were evaluated using multiple regression analysis.     

Successful Treatment of Low PAH-Contaminated Sewage Sludge in Aerobic Bioreactors (7 pp) *

Background, Aims and Scope Polycyclic Aromatic Hydrocarbons (PAHs) are known for their adverse and cumulative effects at low concentration. In particular, the PAHs accumulate in sewage sludge during wastewater treatment, and may thereafter contaminate agricultural soils by spreading sludge on land. Therefore, sludge treatment processes constitute the unique opportunity of PAH removal before their release in the environment. In this study, the ability of aerobic microorganisms to degrade light and heavy PAHs was investigated in continuous bioreactors treating trace-level PAH-contaminated sludge. Methods Several aerobic reactors were operated under continuous and perfectly mixed conditions to simulate actual aerobic sludge digesters. Three sterile control reactors were performed at 35°C, 45°C or 55°C to assess PAH abiotic losses under mesophilic and thermophilic conditions. Three biological reactors were also operated at 35°C, 45°C or 55°C. Furthermore, 250 mM methanol were added in an additional mesophilic reactor (35°C). All reactors were fed with long-term PAH-contaminated sewage sludge, and PAH removal was assessed by inlet/outlet mass balance. In this study, PAH compounds ranged from 2 to 5-unsubstituted aromatic rings, i.e. respectively from Fluorene to Indeno(123cd)pyrene. Results and Discussion Significant abiotic losses were observed for the lightest PAHs (fluorene, phenanthrene and anthracene), while biodegradation occurred for all PAHs. More than 80% of the lightest PAHs were removed. Biodegradation rates inversely correlated with the increasing molecular weight, and seemed limited by the low bioavailability of the heaviest PAHs (only 50% of removal). The enhancement of PAH bioavailability by increasing the process temperature or adding methanol was tested. A temperature increase from 35°C to 45°C and then to 55°C significantly enhanced the biodegradation of the heaviest PAHs from 50% to 80%. However, high abiotic losses were observed for all PAHs at 55°C, which was attributed to volatilization. Optimal conditions were found at 45°C considering the low abiotic losses and the high PAH biodegradation rates. Similar performances were achieved by addition of methanol in the sludge. It was concluded that increasing temperatures or addition of methanol favored PAH diffusion from solids to an aqueous compartment, and enhanced their bioavailability to PAH-degrading microorganisms. Conclusion In this study, the use of long-term acclimated aerobic ecosystems showed the high potential of aerobic microorganisms to degrade a wide range of PAHs at trace levels. However, PAH biodegradation was likely controlled by their low bioavailability. Two aerobic processes have been finally proposed to achieve efficient decontamination of sewage sludge, at 45°C or in the presence of methanol. The PAH concentrations in reactor outlet were lower than the French requirements, and allow the treated sludge to be spread on agricultural land. Recommendations and Outlook The two proposed aerobic processes used physical or chemical diffusing agents. The global ecological impact of using the latter agents for treating trace level contamination must be considered. Since methanol was completely removed during the process, no additional harm is expected after treatment. However, an increase of temperature to 45°C could drastically increase the energy demand in full-scale plants, and therefore the ecological impact of the process. Moreover, since bioavailability controls PAH biodegradation, efficiency of the processes could also be influenced by the hydraulic parameters, such as mixing and aeration rates. Further experimentations in a pilot scale are therefore recommended, as well as a final assessment of the global environmental benefit of using such aerobic processes in the bioremediation of trace level compounds. - Abbreviations (PAHs): Ant – anthracene; B(a)A – benzo(a)anthracene ; B(b)F – benzo(b)fluoranthene; B(k)F – benzo(k)fluoranthene; B(ghi)P – benzo(g,h,i)perylene; B(a)P – benzo(a)pyrene; Chrys – chrysene; DB – dibenzo(a,h)anthracene; Fluor – fluoranthene; Fluo - fluorene; Ind – indeno(1,2,3-c,d)pyrene; Phe - phenanthrene; Pyr – pyrene - * The basis of this peer-reviewed paper is a presentation at the 9th FECS Conference on 'Chemistry and Environment', 29 August to 1 September 2004, Bordeaux, France.