Dimer formation during UV photolysis of diclofenac

Dimer formation was observed during ultraviolet (UV) photolysis of the anti-inflammatory drug diclofenac, and confirmed with mass spectrometry, NMR and fluorescence analysis. The dimers were combinations of the two parent molecules or of the parent and the product of photolysis, and had visible color. Radical formation during UV exposure and dissolved oxygen photosensitized reactions played a role in dimer formation. Singlet oxygen formed via photosensitization by photolysis products of diclofenac. It reacted with diclofenac to form an epoxide which is an intermediate in some dimer formation pathways. Quantum yield of photolysis for diclofenac was 0.21 ± 0.02 and 0.19 ± 0.02 for UV irradiation from medium pressure and low pressure mercury vapor lamps, respectively. Band pass filter experiments revealed that the quantum yield is constant at wavelengths >200 nm. The same dimers formed in laboratory grade water when either of the two UV sources was used. Dimers did not form in wastewater effluent matrix, and diclofenac epoxide molecules may have formed bonds with organic matter rather than each other Implications for the importance of dimer formation in NOM are discussed.     

炼化企业中水紫外线消毒及其影响因素简

研究水质对254 nm紫外线透射率的影响,通过动态实验考察了照射时间、254 nm紫外线透射率以及紫外线剂量对炼化企业中水消毒效果的影响并同时考察异养菌、硫酸盐还原菌和铁细菌的光复活及暗修复现象。结果表明,有机物是影响炼化企业中水紫外线消毒的重要因素;紫外线对炼化企业中水中的异养菌具有良好的灭活作用;增加照射时间对消毒效果的提升作用受254 nm紫外线透射率的影响;紫外线透射率在较低的范围内时对消毒效果的影响相对较大,在较高的范围内时影响较小;紫外线剂量-响应曲线受254 nm紫外线透射率的影响;剂量的“成分”,即照射时间和透射率的不同组合,也会对消毒效果产生影响;在80 mJ/cm²的剂量下,20 h内异养菌出现了较强烈的光复活和暗修复现象,铁细菌仅出现了明显的光复活现象,硫酸盐还原菌没有表现出明显的复活。     

利用UVC去除低浓度苯的实验研究

探讨了不同实验参数对苯的UVC去除效果的影响,获得了苯的去除率与苯的初始浓度、气体流量、相对湿度和氧气含量等参数之间的关系。数据表明,在实验条件范围内,苯的去除率的倒数与苯初始浓度、气体流量之间为线性关系;苯的去除率随相对湿度的增加呈现先升高后缓慢降低的关系,最佳相对湿度值在30%～50%之间;苯的去除率随氧气量的增加而缓慢增加;波长为185+254 nm的UV与254 nm的UV相比净化效果更为理想。还分析了苯降解产生的中间产物,探讨了苯的降解机理。     

Minimization of the formation of disinfection by-products

The drinking water industry is required to minimize DBPs levels while ensuring adequate disinfection. In this study, efficient and appropriate treatment scheme for the reduction of disinfection by-product (DBPs) formation in drinking water containing natural organic matter has been established. This was carried out by the investigation of different treatment schemes consisting of enhanced coagulation, sedimentation, disinfection by using chlorine dioxide/ozone, filtration by sand filter, or granular activated carbon (GAC). Bench scale treatment schemes were applied on actual samples from different selected sites to identify the best conditions for the treatment of water. Samples were collected from effluent of each step in the treatment train in order to analyze pH, UV absorbance at 254 nm (UVA₂₅₄), specific UV absorbance at 254 nm (SUVA₂₅₄), dissolved organic carbon (DOC), haloacetic acids (HAAs) and trihalomethanes (THMs). The obtained results indicated that using pre-ozonation/enhanced coagulation/activated carbon filtration treatment train appears to be the most effective method for reducing DBPs precursors in drinking water treatment.     

SMX degradation by ozonation and UV radiation: a kinetic study

The rate constants of sulfamethoxazole (SMX) degradation by ozonation and UV₂₅₄ radiation were investigated under various parameters including influent ozone gas concentration, initial SMX concentration, UV light intensity, ionic strength, water quality in terms of varying anions (bicarbonate, sulfate and nitrate), humic acid (HA) and pH. The results indicated that the removal of SMX by ozonation and UV₂₅₄ radiation fitted well to a pseudo first-order kinetic model and the rate constants were in the range of (0.9-9.8) × 10⁻³ and (1.7-18.9) × 10⁻³ s⁻¹, respectively. The second-order rate constants of SMX with ozone (k_O3), under varying operational parameters, were also determined and varied in the range of (0.60-3.38) ± 0.13 × 10⁵ M⁻¹ s⁻¹. In addition, SMX degradation through UV pretreatment followed by ozonation in the presence of HA was proved to be an effective method which can remove SMX with a low ozone dose. The results suggested that ozonation of SMX was more affected by concentration of influent ozone gas, alkalinity, and HA, while incident UV light intensity, pH, and HA were the dominant factors influencing UV degradation of SMX.     

UV/ozone degradation of gaseous hexamethyldisilazane (HMDS)

As a carcinogen, hexamethyldisilazane (HMDS) is extensively adopted in life science microscopy, materials science and nanotechnology. However, no appropriate technology has been devised for treating HMDS in gas streams. This investigation evaluated the feasibility and effectiveness of the UV (185+254nm) and UV (254nm)/O(3) processes for degradation of gaseous HMDS. Tests were performed in two batch reactors with initial HMDS concentrations of 32-41mgm(-3) under various initial ozone dosages (O(3) (mg)/HMDS (mg)=1-5), atmospheres (N(2), O(2), and air), temperatures (28, 46, 65 and 80 degrees C), relative humilities (20%, 50%, 65%, 99%) and volumetric UV power inputs (0.87, 1.74, 4.07 and 8.16Wl(-1)) to assess their effects on the HMDS degradation rate. Results indicate that for all conditions, the decomposition rates for the UV (185+254nm) irradiation exceeded those for the UV (254nm)/O(3) process. UV (185+254nm) decompositions of HMDS displayed an apparent first-order kinetics. A process with irradiation of UV (185+254nm) to HMDS in air saturated with water at temperatures of 46-80 degrees C favors the HMDS degradation. With the condition as above and a P/V of around 8Wl(-1), k was approximately 0.20s(-1) and a reaction time of just 12s was required to degrade over 90% of the initial HMDS. The main mechanisms for the HMDS in wet air streams irradiated with UV (185+254nm) were found to be caused by OH free-radical oxidation produced from photolysis of water or O((1)D) produced from photolysis of oxygen. The economic evaluation factors of UV (185+254nm) and UV (254nm)/O(3) processes at different UV power inputs were also estimated.     

Photochemical and photocatalytic degradation of gaseous toluene using short-wavelength UV irradiation with TiO2 catalyst: comparison of three UV sources

The feasibility of the use of short-wavelength UV (254+185 nm) irradiation and TiO2 catalyst for photodegradation of gaseous toluene was evaluated. It was clear that the use of TiO2 under 254+185 nm light irradiation significantly enhanced the photodegradation of toluene relative to UV alone, owed to the combined effect of photochemical oxidation in the gas phase and photocatalytic oxidation on TiO2. The photodegradation with 254+185 nm light irradiation was compared with other UV wavelengths (365 nm (black light blue lamp) and 254 nm (germicidal UV lamp)). The highest conversion and mineralization were obtained with the 254+185 nm light. Moreover, high conversions were achieved even at high initial concentrations of toluene. Catalyst deactivation was also prevented with the 254+185 nm light. Regeneration experiments with the deactivated catalyst under different conditions revealed that reactive oxygen species played an important role in preventing catalyst deactivation by decomposing effectively the less reactive carbon deposits on the TiO2 catalyst. Simultaneous elimination of photogenerated excess ozone and residual organic compounds was accomplished by using a MnO2 ozone-decomposition catalyst to form reactive species for destruction of the organic compounds.     

紫外光(UV)光解油田采出水中多环芳烃

为了探讨紫外光光解人工模拟油田采出水中多环芳烃的降解效率,利用自制反应装置对油田采出水中多环芳烃(PAHs)的紫外光光解做了一个初步研究。研究结果证明,紫外光光解对油田采出水中的多环芳烃萘和芴有显著的降解能力。实验室的测试表明,与紫外UVA(365 nm)、UVB(308 nm)的光照相比,紫外UVC(254 nm)在光照60 min的条件下,2种多环芳烃各自的去除率都近似达到了99%。可见,在光解效力和暴露时间两方面,紫外UVC对采出水中萘和芴的去除具有相对稳定和比较高的效率。     

Fate of citalopram during water treatment with O3, ClO2, UV and Fenton oxidation

In the present study we investigate the fate of citalopram (CIT) at neutral pH using advanced water treatment technologies that include O₃, ClO₂ oxidation, UV irradiation and Fenton oxidation. The ozonation resulted in 80% reduction after 30 min treatment. Oxidation with ClO₂ removed >90% CIT at a dosage of 0.1 mg L⁻¹. During UV irradiation 85% reduction was achieved after 5 min, while Fenton with addition of 14 mg L⁻¹ (Fe²⁺) resulted in 90% reduction of CIT. During these treatment experiments transformation products (TPs) were formed from CIT, where five compounds were identified by using high resolution and tandem mass spectrometry. Among these desmethyl-citalopram and citalopram N-oxide have been previously identified as human metabolites, while three are novel and published here for the first time. The three TPs are a hydroxylated dimethylamino-side chain derivative, a butyrolactone derivative and a defluorinated derivative of CIT.     

The degradation of endocrine disruptor di-n-butyl phthalate by UV irradiation: a photolysis and product study

The direct photolysis of an important endocrine disruptor compound, di-n-butyl phthalate (DBP), has been investigated under monochromatic UV irradiation at 254 nm over a wide pH range (3-11). The investigation was carried out under idealized conditions and has considered both reaction kinetics and the degradation mechanism. It was found that more than 90% of DBP can be degraded within an hour of irradiation in water. A simple model has been developed and used to predict the initial DBP photolysis rate constant at different pH values and initial DBP concentrations. The major decomposition mechanism of DBP is believed to involve the hydrolytic photolysis of the carbon in the alpha and/or beta-position of the ester chain with the production of aromatic carboxylic derivatives. Additionally, multi-degradation pathways are proposed for acid-catalyzed hydrolytic photolysis (pH 3-5), which was found to be useful in explaining the photo-degradation of DBP under acidic conditions. The use of 254 nm UV to photo-degrade DBP was found to be a relatively fast and clean process, especially in neutral to basic conditions.     

Emerging pollutants in sewage, surface and drinking water in Galicia (NW Spain)

A monitoring programme was carried out on wastewater, surface and drinking water on the NW area of Spain during the four seasons of a year period (November 2007-September 2008). This study covered a series of emerging pollutants of different classes, including pharmaceuticals, neutral and acidic organophosphorus flame retardant/plasticizers (OPs), triclosan, phenoxy-herbicides, insect repellents and UV filters. From the total set of 53 compounds, 19 were found in raw wastewater with median concentrations higher than 0.1 μg L⁻¹. Among them, salicylic acid, ibuprofen and the UV filter benzophenone-4 (BP-4) were the most concentrated, exceeding the 1 μg L⁻¹ median value. Subsequently, 11 of these contaminants are not efficiently enough removed in the small WWTPs tested and their median concentrations in effluents still surpassed the 0.1 μg L⁻¹, so that they can spread through surface water. These chemicals are the pharmaceuticals naproxen, diclofenac and atenolol; the OPs tri(2-chloroethyl) phosphate (TCEP), tri(chloropropyl) phosphate (TCPP), tri-n-butyl phosphate (TnBP), diphenyl phosphate (DPhP) and diethylhexyl phosphate (DEHP); and the sulphonate UV filters BP-4 and 2-phenylbenzimidazole-5-sulphonic acid (PBSA). These OPs were then the dominant emerging pollutants occurring in surface and drinking water, where they are detected in the 20-200 ng L⁻¹ range. Pharmaceuticals and UV filters are typically below the 10 ng L⁻¹ level. Finally, herbicides were only detected in the last sampling campaign under the 100 ng L⁻¹ drinking water European Union limit.     

Photodegradation of quinestrol in waters and the transformation products by UV irradiation

Quinestrol is synthetic estrogen used in contraceptive and hormone replacement therapy and occasionally for treating breast cancer and prostate cancer. It can make its way into the environment through sewage discharge and waste disposal produced by human excretions. In this study, the photodegradation kinetics of quinestrol in various conditions was investigated by UV and solar irradiation. The affecting factors were studied including concentration of hydrogen peroxide, different water types, and the initial concentrations of quinestrol. Concurrently, the transformation products and presumed pathways of quinestrol in distilled water by UV irradiation were identified and proposed. The results showed that the degradation of quinestrol in both irradiation conditions followed the pseudo-first-order kinetics. More rapid degradation was observed by UV irradiation (k = 0.018 min⁻¹) than solar irradiation (k = 0.004 h⁻¹), and the photodegradation rate of quinestrol depended on the concentration of hydrogen peroxide, the initial concentration of quinestrol and water types. The transformation products of quinestrol in distilled water were identified by gas chromatography/mass spectrometry. When exposed to UV irradiation, quinestrol in aqueous solution was rapidly degraded, giving at least ten photodegradation products. The chemical structures of ten degradation products were identified on the basis of mass spectrum interpretation and literature data.     

Surfactant effect on persistence of oxadiazolyl 3(2H)-pyridazinones against Pseudaletia separata walker

The photodynamic decomposition of two new insect-growth inhibitors (IGRs), 2-tert-butyl-5-[5′-aryl-2′-(1′,3′,4′-oxadiazolyl)methoxy]-3(2H)-pyridazinones (OPB) and its 4-chloro substituted derivative (OPC), and effect of surfactants on persistence of their bioactivity were taken into investigation. Both chemicals were significantly induced to photolysis by ultraviolet light at 365 nm wavelength and their inhibitory activities against Pseudaletia separata larvae decreased with the increasing irradiation time. However, irradiation at 254 nm wavelength didn't cause their photodegradation. Triton X-100 and Succinic-sulfonie acidic sodium but not Tween 60 possessed strong capability to slow down the decomposition and obviously prolonged the half life of OPC in laboratory and field whilst effects of the three surfactants almost did not preserve the inhibitory activity of OPB. Data suggested that electron-withdrawing halogen (?Cl) on the π electron system in planar benzene-oxadialyl structures might reduce the efficiency of OPC on ultraviolet (UV) photoabsorption, and its hydrophobic interaction with the surfactants might be beneficial for forming stable micellar solubilization, thus sustaining the chemical's bioactivity.     

Photodegradation of perfluorooctanoic acid by synthesized TiO2-MWCNT composites under 365nm UV irradiation

Degradation of perfluorooctanoic acid (PFOA) is of great importance due to its global distribution, persistence and toxicity to bioorganisms. In present study, a composite TiO₂ with multiple wall carbon nano-tubes (MWCNTs) was synthesized using sol-gel method and it was used as photocatalyst to degrade PFOA in water. The prepared composite catalyst displayed significant absorption in UV to visible light region. The loading content of TiO₂ on MWCNTs could be adjusted by changing the ratio of precursor to MWCNTs. Due to the combined effect of the adsorption ability and e⁻ transport capacity of MWCNT, the composites displayed much higher photocatalytic ability to PFOA as compared to pure TiO₂ under UV irradiation. The photocatalyst prepared with 10:1 of tetrabutyl titanate/MWCNT was the most effective. With the optimal dosage at 1.6 g L⁻¹, almost 100% of PFOA was degraded in acid medium after irradiation for 8 h. It was proposed that PFOA were mainly degraded by stepwise losing a moiety of CF₂.     

Degradation of aquatic humic material by ultraviolet light

Natural humic water was treated with ultraviolet (UV) light and UV + hydrogen peroxide (UV/H₂O₂. The effects on the dissolved organic carbon content (DOC), the UV-absorbance at 254 nm (UV-abs.), the molecular size distribution, pH, and mutagenic activity were monitored, and the identity and concentrations of the most abundant gas chromatographable organic degradation products were determined.

The DOC content and the UV-abs. of the water decreased substantially during treatment with UV/H₂O₂. The decreases were dependent on the time of irradiation (UV dose) as well as on the H₂O₂ dose applied. The humus macromolecules were degraded to smaller fragments during irradiation. At higher UV doses, however, part of the dissolved organic matter (DOM) was found to precipitate, probably as a result of polymerization. Oxalic acid, acetic acid, malonic acid, and n-butanoic acid were the most abundant degradation products detected. These acids were found to account for up to 20% and 80% of the DOM in UV- and UV/H₂O₂-treated waters, respectively. No mutagenic activity was generated by the UV irradiation or the UV/H₂O₂ treatment. It is further concluded that the substantial mutagenic activity formed during chlorination of humic waters cannot be decreased by using UV irradiation as a pretreatment step.     

Formation of hazardous by-products resulting from the irradiation of natural organic matter: comparison between UV and VUV irradiation

The use of ultraviolet (UV) or vacuum ultraviolet (VUV) photo-oxidation followed by biological treatment for the removal of natural organic matter (NOM) in drinking water is a potential water treatment technique under investigation. This paper reports on the trihalomethane formation potential (THMFP), the haloacetic acid formation potential (HAAFP), and formation of nitrite and peroxide following both UV and VUV irradiation of NOM prior to biological treatment. The total THMFP was found to decrease with increasing UV and VUV irradiation dose, although there was a linear increase in bromoform formation. Determination of the THMFP of NOM fractions obtained after irradiation, showed that the hydrophobic fraction was dominated by chlorinated species which accounted for the majority of the total THMFP, while bromoform was observed only in the hydrophilic fraction of NOM. VUV irradiation reduced the HAAFP with increasing dose, in contrast, UV irradiation had a limited effect on the overall HAAFP. Following UV or VUV irradiation, the chlorinated species accounted for the majority of HAAFP; however, significant formation of brominated haloacetic acid (HAA) was observed. The nitrate concentration of the untreated water directly influenced the concentration of nitrite produced as a consequence of UV and VUV irradiation. Hydrogen peroxide formation was greater during VUV irradiation than during UV irradiation. Samples exposed to various doses of UV or VUV irradiation (up to 138 J cm(-2)) were deemed non-cytotoxic (African green monkey kidney cells) and non-mutagenic (Ames test).     

Effects of wavelength and water quality on photodegradation of N-Nitrosodimethylamine (NDMA)

N-Nitrosodimethylamine (NDMA) is a potent carcinogen that yields a cancer risk of 10⁻⁶ at concentrations as low as 0.7 ng L⁻¹. Tentative guideline values are set at 3 ng L⁻¹ in California, USA; 9 ng L⁻¹ in Ontario, Canada; 40 ng L⁻¹ nationwide in Canada; and 100 ng L⁻¹ by the World Health Organization. NDMA is a great concern in treating reclaimed water as well as drinking water. UV degradation can be considered effective degradation method. A 1-log reduction of NDMA is achieved by 1000 mJ cm⁻² of a 254-nm low pressure (LP) mercury UV lamp. However, a higher degradation efficiency than that provided by LP lamps is desired in practical treatment. In this study, the effects of wavelength and water quality were investigated to achieve higher degradation efficiency. The effects of wavelength were examined by comparing three UV lamps: a 222-nm Kr Cl Excimer UV lamp, a 254-nm LP mercury UV lamp, and a 230- to 270-nm filtered medium pressure (FMP) mercury UV lamp. The 222-nm lamp and FMP lamp achieved 4 times and 2.8 times higher degradation efficiency, respectively, than the conventional 254-nm LP lamp. Effects on water quality were also simulated by using absorption spectrum data of nitrate solutions and process water from a drinking-water treatment plant. In the simulation, the 222-nm lamp was affected by UV-absorbing compounds in the water, whereas the FMP lamp showed more stable degradation efficiency. Appropriate use of these three types of lamps could enhance the efficiency of degradation of NDMA.     

Photodegradation of malachite green and malachite green carbinol under irradiation with different wavelength ranges

The dye malachite green (MG) is used worldwide as a fungicide in aquaculture. It is a toxic substance which in aqueous solutions is partly converted into its non-ionic colorless form (leucocarbinol). The equilibrium between these two forms is pH-dependent (pK = 6.9). To assess the photodegradation of MG under sunlight conditions, both species were irradiated separately in aqueous solutions with different pH values (4.0 and 12.0) using various ultraviolet and visible wavelength ranges (UV/VIS). A 700 W high-pressure mercury lamp with special filters was used. No artificial photooxidizers such as H₂O₂ or TiO₂ were added. MG leucocarbinol proved to be much more sensitive to irradiation than the dye form. Quantum yields Φ were calculated for some wavelength ranges as follows: MG carbinol: Φ_(280-312nm) is 4.3 × 10⁻³, Φ_(313-410nm) is 5.8 × 10⁻³, and MG dye: Φ_(280-312nm) is 4.8 × 10⁻⁵, Φ_(313-365nm) is 1.1 × 10⁻⁵, and Φ_(>365nm) is 0, respectively. Therefore, the solar photolysis of MG is an important sink and primarily depends on the photodegradation of the colorless leucocarbinol. During the irradiation of MG leucocarbinol with wavelengths >365 nm, an intermediate was formed which has photocatalytical properties.