Oxidative degradation of dimethylsulfoxide by locally concentrated hydroxyl radicals in streamer corona discharge process

This study systematically investigates the characteristic degradation behaviors of dimethylsulfoxide (DMSO) by the streamer corona discharge process (SCDP) in water. The analysis of the oxidized intermediates of DMSO shows that hydroxyl radical (*OH) is the main oxidant responsible for the degradation of DMSO in the SCDP. The various experiments on the degradation and mineralization of DMSO, and the effect of the *OH scavenger suggest that the SCDP produces locally concentrated *OHs in and around the plasma channel. This explanation was also supported by the formation of H(2)O(2) and the effect of the *OH scavenger on the H(2)O(2) production rate in the SCDP. Based on the kinetic data for the degradation of DMSO and the production of H(2)O(2) in the SCDP, the volume of the active region in which the *OHs are concentrated, and the effective concentration of *OH in that region were estimated to be 0.21 microl and 5.0 x 10(-3)M, respectively. This level of *OH concentration in the SCDP is approximately 10(7)-10(9) times higher than that generated in ordinary advanced oxidation processes using *OH. The ramifications of the results obtained in this study on successful water treatment using the SCDP are also discussed.     

Identification of new ozonation disinfection byproducts of 17β-estradiol and estrone in water

Estrogens are a class of micro-pollutants found in water at low concentrations (in the ng L⁻¹ range), but often sufficient to exert estrogenic effects due to their high estrogenic potency. Disinfection of waters containing estrogens through oxidative processes has been shown to lead to the formation of disinfection byproducts, which may also be estrogenic. The present work investigates the formation of disinfection byproducts of 17β-estradiol (E2) and estrone (E1) in the treatment of water with ozone. Experiments have been carried out at two different concentrations of the estrogens in ground water (100 ng L⁻¹ and 100 μg L⁻¹) and at varying ozone dosages (0-30 mg L⁻¹). Detection of the estrogens and their disinfection byproducts in the water samples has been performed by means of ultra performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS) with a triple quadrupole (QqQ) and a quadrupole-time of flight (QqTOF) instrument. Both E2 and E1 have been found to form two main byproducts, with molecular mass (MM) 288 and 278 in the case of E2, and 286 and 276 in the case of E1, following presumably the same reaction pathways. The E2 byproduct with MM 288 has been identified as 10epsilon-17beta-dihydroxy-1,4-estradieno-3-one (DEO), in agreement with previously published results. The molecular structures and the formation pathways of the other three newly identified byproducts have been suggested. These byproducts have been found to be formed at both high and low concentrations of the estrogens and to be persistent even after application of high ozone dosages.     

Studies of inactivation, retardation and accumulation of viruses in porous media by a combination of dye labeled and native bacteriophage probes

Penetration of viruses through soils is governed by the processes of transport, reversible adsorption, accumulation and inactivation. Until now, it was difficult to decouple the latter two processes and accurately predict viral fate. The present work describes a novel method-tracer studies with a mixture of native and fluorescent-dyed bacteriophages-that facilitates parallel quantification of the two processes. When the native phages are experiencing both accumulation and inactivation, the labeled ones are inactivated already and therefore can only be accumulated. Thus the effect of inactivation is applicable to native bacteriophages only and depletion of phage concentration due to inactivation can be elucidated from a total phage balance. The novel approach is exemplified by batch and column studies of the effects of temperature, pH, and saturation, on inactivation of MS2 bacteriophage. A three-parameter model accounting for inactivation, reversible adsorption (i.e., retardation), and accumulation is implemented.     

Stability considerations of aspartame in the direct analysis of artificial sweeteners in water samples using high-performance liquid chromatography-tandem mass spectrometry (HPLC-MS/MS)

A HPLC-MS/MS method is presented for the simultaneous determination of frequently used artificial sweeteners (ASs) and the main metabolite of aspartame (ASP), diketopiperazine (DKP), in environmental water samples using the direct-injection (DI) technique, thereby achieving limits of quantification (LOQ) of 10 ng L⁻¹. For a reliable quantification of ASP pH should be adjusted to 4.3 to prevent formation of the metabolite. Acesulfame (ACE), saccharin (SAC), cyclamate (CYC) and sucralose (SUC) were ubiquitously found in water samples. Highest concentrations up to 61 μg L⁻¹ of ACE were found in wastewater effluents, followed by surface water with concentrations up to 7 μg L⁻¹, lakes up to 600 ng L⁻¹ and groundwater and tap water up to 70 ng L⁻¹. The metabolite DKP was only detected in wastewater up to 200 ng L⁻¹ and at low detection frequencies.     

Characterizing pesticide sorption and degradation in microscale biopurification systems using column displacement experiments

Biopurification systems treating pesticide contaminated water are very efficient, however they operate as a black box. Processes inside the system are not yet characterized. To optimize the performance, knowledge of degradation and retention processes needs to be generated. Therefore, displacement experiments were carried out for four pesticides (isoproturon, bentazone, metalaxyl, linuron) in columns containing different organic mixtures. Bromide, isoproturon and bentazone breakthrough curves (BTCs) were well described using the convection-dispersion equation (CDE) and a first-order degradation kinetic approach. Metalaxyl and linuron BTCs were well described using the CDE model expanded with Monod-type kinetics. Freundlich sorption, first-order degradation and Monod kinetics coefficients were fitted to the BTCs. Fitted values of the distribution coefficient K_f,column were much lower than those determined from batch experiments. Based on mobility, pesticides were ranked as: bentazone > metalaxyl - isoproturon > linuron. Based on degradability, pesticides were ranked as: linuron > metalaxyl - isoproturon > bentazone.     

Inactivation and injury assessment of Escherichia coli during solar and photocatalytic disinfection in LDPE bags

Solar disinfection (SODIS) of Escherichia coli suspensions in low-density polyethylene bag reactors was investigated as a low-cost disinfection method suitable for application in developing countries. The efficiency of a range of SODIS reactor configurations was examined (single skin (SS), double skin, black-backed single skin, silver-backed single skin (SBSS) and composite-backed single skin) using E. coli suspended in model and real surface water. Titanium dioxide was added to the reactors to improve the efficiency of the SODIS process. The effect of turbidity was also assessed. In addition to viable counts, E. coli injury was characterised through spread-plate analysis using selective and non-selective media. The optimal reactor configuration was determined to be the SBSS bag (t₅₀ = 9.0 min) demonstrating the importance of UVA photons, as opposed to infrared in the SODIS disinfection mechanism. Complete inactivation (6.5-log) was achieved in the presence of turbidity (50 NTU) using the SBSS bag within 180 min simulated solar exposure. The addition of titanium dioxide (0.025 g L⁻¹) significantly enhanced E. coli inactivation in the SS reactor, with 6-log inactivation observed within 90 min simulated solar exposure. During the early stages of both SODIS and photocatalytic disinfection, injured E. coli were detected; however, irreversible injury was caused and re-growth was not observed. Experiments under solar conditions were undertaken with total inactivation (6.5-log) observed in the SS reactor within 240 min, incomplete inactivation (4-log) was observed in SODIS bottles exposed to the same solar conditions.     

Fates and transport of PPCPs in soil receiving reclaimed water irrigation

Fates and transport of 9 commonly found PPCPs of the reclaimed water were simulated based on the HYDRUS-1D software that was validated with data generated from field experiments. Under the default scenario in which the model parameters and input data represented the typical conditions of turf grass irrigation in southern California, the adsorption, degradation, and volatilization of clofibric acid, ibuprofen, 4-tert-octylphenol, 4-n-nonylphenol, naproxen, triclosan, diclofenac sodium, bisphenol A and estrone in the receiving soils were tracked for 10 years. At the end, their accumulations in the 90 cm soil profile varied from less than 1 ng g⁻¹ to about 140 ng g⁻¹ and their concentrations in the drainage water in the 90 cm soil depth varied from nil to μg L⁻¹ levels. The adsorption and microbial degradation processes interacted to contain the PPCPs entirely within surface 40 cm of the soil profiles. Leaching and volatilization were not significant processes governing the PPCPs in the soils. The extent of accumulations in the soils did not appear to produce undue ecological risks to the soil biota. PPCPs did not represent any potential environmental harm in reclaimed water irrigation.     

Waste water treatment plants as sources of polyfluorinated compounds, polybrominated diphenyl ethers and musk fragrances to ambient air

To investigate waste water treatment plants (WWTPs) as sources of polyfluorinated compounds (PFCs), polybrominated diphenyl ethers (PBDEs) and synthetic musk fragrances to the atmosphere, air samples were simultaneously taken at two WWTPs and two reference sites using high volume samplers. Contaminants were accumulated on glass fiber filters and PUF/XAD-2/PUF cartridges, extracted compound-dependent by MTBE/acetone, methanol, or hexane/acetone and detected by GC-MS or HPLC-MS/MS. Total (gas + particle phase) concentrations ranged from 97 to 1004 pg m⁻³ (neutral PFCs), <MQL to 13 pg m⁻³ (ionic PFCs), 5781 to 482,163 pg m⁻³ (musk fragrances) and <1 to 27 pg m⁻³ (PBDEs) and were usually higher at WWTPs than at corresponding reference sites, revealing that WWTPs can be regarded as sources of musk fragrances, PFCs and probably PBDEs to the atmosphere. Different concentrations at the two WWTPs indicated an influence of WWTP size or waste water origin on emitted contaminant amounts.     

Formation of dioxins during exposure of pesticide formulations to sunlight

Chlorinated pesticides can contain impurities of dibenzo-p-dioxins and dibenzofurans (PCDD/Fs), and their precursors, as a result of various manufacturing processes and conditions. As precursor formation of PCDD/Fs can also be mediated by ultraviolet light (UV), this study investigated whether PCDD/Fs are formed when currently used pesticides are exposed to natural sunlight. Formulations containing pentachloronitrobenzene (PCNB; n = 2) and 2,4-dichlorophenoxyacetic acid (2,4-D; n = 1) were exposed to sunlight in quartz tubes, and the concentration of 93 PCDD/F congeners were monitored over time. Considerable formation of PCDD/Fs was observed in both PCNB formulations (by up to 5600%, to a maximum concentration of 57 000 μg ∑PCDD/F kg⁻¹) as well as the 2,4-D formulation (by 3000%, to 140 μg ∑PCDD/F kg⁻¹). TEQ also increased by up to 980%, to a maximum concentration of 28 μg kg⁻¹ in PCNB, but did not change in the 2,4-D formulation. Assuming similar yields as observed in the present study as a worst case scenario the use of PCNB in Australia may result in the formation of 155 g TEQ annum⁻¹, contributed primarily by OCDD formation. This warrants detailed evaluations on the contemporary release of PCDD/Fs to the environment after the use of pesticides. Changes in congener profiles (including the ratio of PCDDs to PCDFs (DF ratio)) suggest that pesticide sources of PCDD/Fs after sunlight exposure may not be recognized based on matching source fingerprints established from manufacturing impurities. These changes also provide preliminary insights into the possible formation routes and types of precursors involved.     

Differential global profiling as a new analytical strategy for revealing micropollutant treatment by-products: application to ethinylestradiol and chlorination water treatment

The detection and structural elucidation of micropollutants treatment by-products are major issues to estimate efficiencies of the processes employed for drinking water production versus endocrine disruptive compounds contamination. This issue was mainly investigated at the laboratory scale and in high concentration conditions. However, potential by-products generated after chlorination can be influenced by the dilution factor employed in real conditions. The present study proposes a new methodology borrowed to the metabolomic science, using liquid chromatography coupled to high-resolution mass spectrometry, in order to reveal potential chlorination by-products of ethinylestradiol in spiked real water samples at the part-per-billion level (5 μg L⁻¹). Conventional targeted measurements first demonstrated that chlorination with sodium hypochlorite (0.8 mg L⁻¹) led to removals of ethinylestradiol over 97%. Then, the developed differential global profiling approach permitted to reveal eight chlorination by-products of EE2, six of them being described for the first time. Among these eight halogenated compounds, five have been structurally identified, demonstrating the potential capabilities of this new methodology applied to environmental samples.     

Potential of BAC combined with UVC/H2O2 for reducing organic matter from highly saline reverse osmosis concentrate produced from municipal wastewater reclamation

The organic matter present in the concentrate streams generated from reverse osmosis (RO) based municipal wastewater reclamation processes poses environmental and health risks on its disposal to the receiving environment (e.g., estuaries, bays). The potential of a biological activated carbon (BAC) process combined with pre-oxidation using a UVC/H₂O₂ advanced oxidation process for treating a high salinity (TDS ∼ 10 000 mg L⁻¹) municipal wastewater RO concentrate (ROC) was evaluated at lab scale during 90 d of operation. The combined treatment reduced the UVA₂₅₄ and colour of the ROC to below those for the influent of the RO process (i.e., biologically treated secondary effluent), and the reductions in DOC and COD were approximately 60% and 50%, respectively. UVC/H₂O₂ was demonstrated to be an effective means of converting the recalcitrant organic compounds in the ROC into biodegradable substances which were readily removed by the BAC process, leading to a synergistic effect of the combined treatment in degrading the organic matter. The tests using various BAC feed concentrations suggested that the biological treatment was robust and consistent for treating the high salinity ROC. Using Microtox analysis no toxicity was detected for the ROC after the combined treatment, and the trihalomethane formation potential was reduced from 3.5 to 2.8 mg L⁻¹.     

Identification and dose dependency of ibuprofen biliary metabolites in rainbow trout

The biotransformation of the anti-inflammatory drug ibuprofen (IBF) was studied by exposing rainbow trout (Oncorhynchus mykiss) to IBF via intraperitoneal (i.p.) injection, and via water at four (0.17, 1.9, 13 and 145 μg L⁻¹) exposure levels for 4 d. Following exposure, the bile was collected and analyzed by LC–MS/MS methods. The identification of the formed metabolites in i.p. injected fish bile was based on the exact mass determinations by a time-of-flight mass analyzer (Q–TOF–MS) and on the studies of fragments and fragmentation patterns of precursor ions by ion trap mass analyzer (IT-MS). In addition to unmetabolized IBF, several phase I and phase II metabolites were found in the bile. The main metabolites were acyl glucuronides and taurine conjugates of IBF and of hydroxylated IBFs. The bioconcentration factors (BCF_bile), defined as the ratio of the sum of IBF and its metabolites in fish bile to the concentration of IBF in water, was determined following enzymatic deconjugation and was found to range from 14 000 to 49 000. The highest BCF_bile was found at the lowest exposure concentration (0.17 μg L⁻¹). The results show that rainbow trout has a high capacity for biotransformation of IBF, and the exposure of fish to sub μg L⁻¹ concentrations of IBF can be determined by the analyses of the biliary metabolites of the compound.     

Chemical and physical characterization of produced waters from conventional and unconventional fossil fuel resources

Characterization of produced waters (PWs) is an initial step for determining potential beneficial uses such as irrigation and surface water discharge at some sites. A meta-analysis of characteristics of five PW sources [i.e. shale gas (SGPWs), conventional natural gas (NGPWs), conventional oil (OPWs), coal-bed methane (CBMPWs), tight gas sands (TGSPWs)] was conducted from peer-reviewed literature, government or industry documents, book chapters, internet sources, analytical records from industry, and analyses of PW samples. This meta-analysis assembled a large dataset to extract information of interest such as differences and similarities in constituent and constituent concentrations across these sources of PWs. The PW data analyzed were comprised of 377 coal-bed methane, 165 oilfield, 137 tight gas sand, 4000 natural gas, and 541 shale gas records. Majority of SGPWs, NGPWs, OPWs, and TGSPWs contain chloride concentrations ranging from saline (>30 000 mg L⁻¹) to hypersaline (>40 000 mg L⁻¹), while most CBMPWs were fresh (<5000 mg L⁻¹). For inorganic constituents, most SGPW and NGPW iron concentrations exceeded the numeric criterion for irrigation and surface water discharge, while OPW and CBMPW iron concentrations were less than the criterion. Approximately one-fourth of the PW samples in this database are fresh and likely need minimal treatment for metal and metalloid constituents prior to use, while some PWs are brackish (5000-30 000 mg Cl⁻ L⁻¹) to saline containing metals and metalloids that may require considerable treatment. Other PWs are hypersaline and produce a considerable waste stream from reverse osmosis; remediation of these waters may not be feasible. After renovation, fresh to saline PWs may be used for irrigation and replenishing surface waters.     

The extractability and mineralisation of cypermethrin aged in four UK soils

Cypermethrin is a widely used insecticide that has caused concern due to its toxicity in the aquatic environment. As with all land applied pesticides, the most significant source of water pollution is from the soil, either due to leaching or washoff. The behaviour of cypermethrin in the soil controls the likelihood of future pollution incidents, with two of the most significant processes being the formation of bound residues and microbial degradation. The formation of bound residues and mineralisation was measured in four organically managed soils from the UK. The formation of bound residues was measured using three different extraction solutions, 0.01 M CaCl₂, 0.05 M HPCD and acetonitrile. Biodegradation was assessed by measurement of mineralisation of cypermethrin to CO₂. The formation of bound residues varied according to extraction method, soil type and length of ageing. In two of the four soils studied, acetonitrile extractability decreased from 100% initially to 12-14% following 100 d ageing. The extent of mineralisation increased after 10-21 d ageing, reaching 33% of remaining activity in one soil, however following 100 d ageing the extent of mineralisation was significantly reduced in three out of the four soils. As with the formation of bound residues, mineralisation was impacted by soil type and length of ageing.     

Uranium in Kosovo’s drinking water

The results of this paper are an initiation to capture the drinking water and/or groundwater elemental situation in the youngest European country, Kosovo. We aim to present a clear picture of the natural uranium concentration in drinking water and/or groundwater as it is distributed to the population of Kosovo. Nine hundred and fifty-one (951) drinking water samples were analyzed by inductively coupled plasma mass spectrometry (ICPMS). The results are the first countrywide interpretation of the uranium concentration in drinking water and/or groundwater, directly following the Kosovo war of 1999. More than 98% of the samples had uranium concentrations above 0.01 μg L⁻¹, which was also our limit of quantification. Concentrations up to 166 μg L⁻¹ were found with a mean of 5 μg L⁻¹ and median 1.6 μg L⁻¹ were found. Two point six percent (2.6%) of the analyzed samples exceeded the World Health Organization maximum acceptable concentration of 30 μg L⁻¹, and 44.2% of the samples exceeded the 2 μg L⁻¹ German maximum acceptable concentrations recommended for infant food preparations.     

Photolytic and photocatalytic degradation of 6-chloronicotinic acid

This work describes for the first time the photolytic and photocatalytic degradation of 6-chloronicotinic acid (6CNA) in double deionised water, which is a degradation product of neonicotinoid insecticides imidacloprid and acetamiprid, and it is known to appear in different environmental matrices. Photolytic experiments were performed with three UVA (ultraviolet A) polychromatic fluorescent lamps with broad maximum at 355 nm, while photocatalytic experiments were performed using immobilised titanium dioxide (TiO₂) on six glass slides in the spinning basket inside a photocatalytic quartz cell under similar irradiation conditions. Photolytic degradation revealed no change in concentration of 6CNA within 120 min of irradiation, while the photocatalytic degradation within 120 min, obeyed first-order kinetics. The observed disappearance rate constant was k = 0.011 ± 0.001 min⁻¹ and t_1/2 was 63.1 ± 5.5 min. Mineralisation rate was estimated through total organic carbon (TOC) and measurements revealed no carbon removal in case of photolysis after 120 min of exposure. However in photocatalytic experiments 46 ± 7% mineralisation was achieved within 120 min of irradiation. Nevertheless, the removal of total nitrogen (TN) was not observed across all experiments. Ion chromatographic analyses indicated transformation of chlorine atoms to chloride and increase of nitrate(V) ions only via photocatalytic experiments. Efficiency of selected advanced oxidation process (AOP) was investigated through toxicity assessment with Vibrio fischeri luminescent bacteria and revealed higher adverse effects of treated samples on bacteria following photocatalytic degradation in spite of the fact that higher mineralisation was achieved. New hydroxylated product generated in photocatalytic experiments with TiO₂, was confirmed with liquid chromatography-electro spray ionisation mass spectrometry (LC-ESI-MS/MS) analyses, gas chromatography-mass spectrometry (GC-MS) and nuclear magnetic resonance spectroscopy (¹H NMR).     

Determination of cyclic volatile methylsiloxanes in water,sediment, soil,biota, and biosolid using large-volume injection–gas chromatography–mass spectrometry

Several methods were developed to detect the cyclic volatile methylsiloxanes (cVMSs) including octamethylcyclotetrasiloxane (D4), decamethylcyclopentasiloxane (D5), and dodecamethylcyclohexasiloxane (D6) in water, sediment, soil, biota, and biosolid samples. Analytical techniques employed to optimize measurement of this compound class in various matrices included membrane-assisted solvent extraction in water, liquid–solid extraction for sediment, soil, biota, and biosolid samples. A subsequent analysis of the extract was conducted by large-volume injection–gas chromatography−mass spectrometry (LVI−GC−MS). These methods employed no evaporative techniques to avoid potential losses and contamination of the volatile siloxanes. To compensate for the inability to improve detection limits by concentrating final sample extract volumes we used a LVI–GC–MS. Contamination during analysis was minimized by using a septumless GC configuration to avoid cVMS’s associated with septum bleed. These methods performed well achieving good linearity, low limits of detection, good precision, recovery, and a wide dynamic range. In addition, stability of cVMS in water and sediment was assessed under various storage conditions. D4 and D5 in Type-I (Milli-Q) water stored at 4 °C were stable within 29 d; however, significant depletion of D6 (60–70%) occurred only after 3 d. Whereas cVMS in sewage influent and effluent were stable at 4 °C within 21 d. cVMS in sediment sealed in amber glass jars at −20 °C and in pentane extracts in vials at −15 °C were stable during 1 month under both storage conditions.     

Copper oxide nanoparticles can induce toxicity to the freshwater shredder Allogamus ligonifer

Increased commercialisation of nanometal-based products augments the possibility of their deposition into aquatic ecosystems; this, in turn, may pose risks to aquatic biota and associated ecological functions. Freshwater invertebrate shredders mostly use microbially-colonized plant litter as food resource and play an important role in aquatic detritus food webs. We assessed lethal effects of nanoCuO on the shredder Allogamus ligonifer (Trichoptera, Limnephilidae) by determining the concentration that induced 50% of death (LC₅₀), and sublethal effects of nanoCuO on the feeding behaviour and growth of the shredder by exposing the animals to: (i) stream water supplemented with nanoCuO and microbially-colonized leaves, and (ii) stream water (without nanoCuO) and microbially-colonized leaves pre-exposed to nanoCuO. Results from acute lethal tests showed that the 96 h LC₅₀ of nanoCuO was very high (569 mg L⁻¹). In the absence of nanoparticles, leaf consumption rate was 0.27 mg leaf DM mg⁻¹ animal DM d⁻¹ and the shredder growth rate was 56 μg animal DM mg⁻¹ animal DM d⁻¹. A significant inhibition in leaf consumption rate (up to 47%) and invertebrate growth rate (up to 46%) was observed when shredders were exposed to the higher tested sublethal concentration of nanoCuO (75 mg L⁻¹) through either contaminated stream water or pre-contaminated food. The exposure to increased nanoCuO concentration via water or pre-contaminated food led to higher accumulation of copper in the larval body. Leached water-soluble ionic copper from the nanoCuO adsorbed or accumulated in the shredder (up to 10.2% of total Cu) seemed to influence the feeding behaviour and growth of the shredder.     

Wastewater reuse in Mediterranean semi-arid areas: The impact of discharges of tertiary treated sewage on the load of polar micro pollutants in the Llobregat river (NE Spain)

The presence of sewage-borne micro contaminants in environmental waters is directly related to the discharge of treated effluents from wastewater treatment plants (WWTP) and the flow rate of the receiving river waters. Mediterranean rivers, in particular, are characterized by important fluctuations in the flow rates and heavy pollution pressures resulting from extensive urban, industrial and agricultural activities. This translates into contamination levels in these rivers often higher than those in other larger European basins. The present work provides an overview of the occurrence of five groups of organic contaminants (131 compounds) namely pharmaceuticals, illicit drugs, polar pesticides, estrogens, alkylphenols and related ethoxylates in WWTP tertiary treatment effluents. Data gathered during a period of water reuse carried out in the lower stretch of the Llobregat river (NE Spain), in the surroundings of the town of Barcelona as a consequence of the severe drought that took place along the years 2007-2008 are presented as illustrative example. In general, measured concentrations of the target compounds were in the low to mid ng L⁻¹ range. The total concentration of each compound class downstream to the discharge point was similar or slightly higher than that found upstream. Regarding the loads calculated for each compound, the relative contribution from the river upstream and the tertiary effluent were highly compound depending with no apparent trend. However, estimation of the overall bulk loads for each compound class determined in the Llobregat river showed the following rank order: pharmaceuticals > alkylphenols > pesticides > illicit drugs ? estrogens.