Application of 'waste' wood-shaving bottom ash for adsorption of azo reactive dye

The utilization of wood-shaving bottom ash (WBA) for the removal of Red Reactive 141 (RR141), an azo reactive dye, was investigated. WBA/H(2)O and WBA/H(2)SO(4) were made by treating WBA with water and 0.1M H(2)SO(4), respectively, to increase adsorption capacity. Adsorption of RR141 from reactive dye solution (RDS) and reactive dye wastewater (RDW) by WBA/H(2)O and WBA/H(2)SO(4) involved the BET surface area and pore size diameter. Properties of adsorbents, effect of contact time, initial pH of solution, dissolved metals and elution studies indicated that the decolorisation mechanism involved both chemical adsorption and precipitation with calcium ions. In addition, the WBA/H(2)SO(4) surface might contain sulphate-cation complexes that were specific to enhancing dye adsorption from RDW. The adsorption isotherm had a best fit by the Freundlich model. Freundlich parameters showed that WBA/H(2)O used more heterogeneous surface than WBA/H(2)SO(4) and activated carbon for RDW adsorption. A thermodynamic study indicated that RDW adsorption was an endothermic process. The maximum dye adsorption capacities of WBA/H(2)O, WBA/H(2)SO(4) and activated carbon obtained from a Langmuir model at 30 degrees C were 24.3, 29.9, and 41.5mgl(-1), respectively. In addition, WBA/H(2)O and WBA/H(2)SO(4) could reduce colour and high chemical oxygen demand (COD) of real textile wastewater. According to the difficulty in the elution study, it was an environmentally safe disposal of this waste. Therefore, WBA, a waste from combustion of wood shavings, was suitable to be used as an effective adsorbent for azo reactive dye removal.     

Determination of model parameters for zinc (II) ion biosorption onto powdered waste sludge (PWS) in a fed-batch system

Biosorption of zinc (II) ions onto pre-treated powdered waste sludge (PWS) was investigated using a completely mixed tank operating in fed-batch mode instead of an adsorption column. Experiments with variable feed flow rate (0.05-0.5 L h(-1)), feed Zn(II) ion concentrations (37.5-275 mg L(-1)) and amount of adsorbent (1-6 g PWS) were performed using fed-batch operation at pH 5 and room temperature (20-25 degrees C). Break-through curves describing variations of aqueous (effluent) zinc ion concentrations with time were determined for different operating conditions. Percent zinc removal from the aqueous phase decreased, but the biosorbed (solid phase) zinc ion concentration increased with increasing feed flow rate and zinc concentration. A modified Bohart-Adams equation was used to determine the biosorption capacity of PWS (q'(s)) and the rate constant (K) for zinc ion biosorption. Biosorption capacity (q'(s)=57.7 g Zn kg(-1) PWS) of PWS in fed-batch operation was found to be comparable with powdered activated carbon (PAC) in column operations. However, the adsorption rate constant (K=9.17 m(3) kg(-1) h(-1)) in fed-batch operation was an order of magnitude larger than those obtained in adsorption columns because of elimination of mass transfer limitations encountered in the column operations. Therefore, a completely mixed tank operated in fed-batch mode was proven to be more advantageous as compared to adsorption columns due to better contact between the phases yielding faster adsorption rates.     

Growth factors, kinetics and biodegradation mechanism associated with Pseudomonas nitroreducens TX1 grown on octylphenol polyethoxylates

The growth properties and biodegradation mechanism of a Gram-negative bacterium, Pseudomonas nitroreducens TX1 that was able to grow on branched octylphenol polyethoxylates (OPEO(n), average n=9.5) as the sole carbon source over a wide concentration range (1-100,000 mgl(-1)) were studied. Analysis of growth factors indicated the highest specific growth rate (micro) of 0.53 h(-1) was obtained at an initial concentration of 5,000 mgl(-1) OPEO(n). An optimal C/N ratio of 12 was obtained for (NH(4))(2)SO(4) as the nitrogen source in a cultivated medium at pH 7. The kinetic analysis demonstrated that bacterial growth and OPEO(n) degradation followed the Monod equation and were based on a substrate concentration inhibition model and pseudo-first-order reaction, respectively. The substrate inhibition coefficient was over 18,000 mgl(-1) and this indicates that the strain has an ability to sustain growth at high concentrations of OPEO(n) and use it as the sole carbon source under such a stress condition. Furthermore, LC-MS analysis showed that the biodegradation mechanism of dodecyl octaethoxylate (AEO8) by P. nitroreducens TX1 was the sequential cleavage of the ethoxylate chain.     

Loofa egyptiaca as a novel adsorbent for removal of direct blue dye from aqueous solution

In this paper, Loofa egyptiaca (LE), an agricultural plant cultivated in Egypt, was used to prepare low-cost activated carbon (LE_C1 and LE_C2) adsorbents. The adsorbents (LE, LE_C1 and LE_C2) were evaluated for their ability to remove direct blue 106 dye from aqueous solutions. Batch mode experiments were conducted using various parameters such as pH, contact time, dye concentration and adsorbent concentration. The surface chemistry of LE, LE_C1 and LE_C2 was analyzed by scanning electron microscopy (SEM). The experimental data were examined using Langmuir, Freundlich, Temkin and Harkins–Jura isotherms. The results showed that the adsorption of direct blue 106 was maximal at the lowest value of pH (pH = 2). Removal efficiency was increased with an increase in dye concentration and a decrease in amount of adsorbent. Maximum adsorption capacity was found to be 57.14, 63.3 and 73.53 mg/g for LE, LE_C1 and LE_C2 respectively. Kinetics were also investigated using pseudo-first-order, pseudo-second-order and intra-particle diffusion models. The experimental data fitted very well with the pseudo-first-order and pseudo-second-order kinetic models. The results indicate that LE, LE_C1 and LE_C2 could be employed as adsorbents for the removal of direct blue dye from aqueous solutions.     

Azadirachta indica leaf powder as an effective biosorbent for dyes: a case study with aqueous Congo Red solutions

In the present work, the leaves of Azadirachta indica (locally known as the Neem tree) in the form of a powder were investigated as a biosorbent of dyes taking aqueous Congo Red solution as a model system. The sorbent was made from mature Neem leaves and was investigated in a batch reactor under variable system parameters such as concentration of the aqueous dye solution, agitation time, adsorbent amount, pH, and temperature. An amount of 0.6 g of the Neem leaf powder (NLP) per litre could remove 52.0-99.0% of the dye from an aqueous solution of concentration 2.87 x 10(-2) mmol l(-1) with the agitation time increasing from 60 to 300 min. The interactions were tested with respect to both pseudo first-order and second-order reaction kinetics; the latter was found to be more suitable. Considerable intra-particle diffusion was found to occur simultaneously. The sorption process was in conformity with Langmuir and Freundlich isotherms yielding values of the adsorption coefficients in the following ranges: Freundlich n: 0.12-0.19, Kf: 0.1039-0.2648 L g(-1); Langmuir qm: 41.24-128.26 g kg(-1), b: 443.3-1898.0 l mmol(-1), which supported favourable adsorption. The Langmuir monolayer capacity (qm) was high and the values of the coefficient b indicated the equilibrium, dye + NLP = dye...NLP being shifted overwhelmingly towards adsorption. Thermodynamically, the sorption process was exothermic with an average heat of adsorption of -12.75 kJ mol(-1). The spontaneity of the sorption process was also confirmed by the favourable values of Gibbs energy (mean values: -1.09 to -1.81 kJ mol(-1)) and entropy of adsorption (range: -18.97 to -56.32 J mol(-1)K(-1)). The results point to the effectiveness of the Neem leaf powder as a biosorbent for removing dyes like Congo Red from water.     

Exploitation of Trichoderma harzianum mycelial waste for the removal of rhodamine 6G from aqueous solution

The harvested mycelial waste of Trichoderma harzianum was used as an adsorbent for the removal of rhodamine 6G and was studied in batch mode. The effects of agitation time and initial dye concentration, adsorbent dosage and pH were examined. The study revealed that the amount of dye adsorbed (mgg(-1)) increased with increase in agitation time and reached equilibrium after 120 min, for dye concentrations of 10-50 mg L(-1). The adsorbent dosage of 1.0 g/50 mL and pH of 8.0 were found to be optimum for maximum dye removal. The batch mode adsorption data followed both the Langmuir and Freundlich isotherms. The pseudo first- and second-order rate kinetics were applied to the adsorbent system. The adsorption kinetics of rhodamine 6G showed that the pseudo-second-order kinetic model provided the best correlation of the equilibrium data. The study implies that it is possible to develop a dye removal system by using T. harzianum biomass, which occurs as sludge in waste stream of fermentation industries.     

Adsorption of basic dye from aqueous solution onto fly ash

The fly ash treated by H₂SO₄ was used as a low-cost adsorbent for the removal of a typical dye, methylene blue, from aqueous solution. An increase in the specific surface area and dye-adsorption capacity was observed after the acid treatment. The adsorption isotherm and kinetics of the treated fly ash were studied. The experimental results were fitted using Langmuir and Freundlich isotherms. It shows that the Freundlich isotherm is better in describing the adsorption process. Two kinetic models, pseudo-first order and pseudo-second order, were employed to analyze the kinetic data. It was found that the pseudo-second-order model is the better choice to describe the adsorption behavior. The thermodynamic study reveals that the enthalpy (ΔH⁰) value is positive (5.63 kJ/mol), suggesting an endothermic nature of the adsorption.     

Environmental factors influencing attenuation of methane and hydrochlorofluorocarbons in landfill cover soils

The influence of different environmental factors on methane oxidation and degradation of hydrochlorofluorocarbons (HCFCs) was investigated in microcosms containing soil sampled at Skellingsted Landfill, Denmark. The soil showed a high capacity for methane oxidation resulting in a maximum oxidation rate of 104 microg CH4 g(-1) h(-1) and a low affinity of methane with a half-saturation constant of 2.0% v/v. The hydrochlorofluorocarbons HCFC-21 (dichlorofluoromethane) and HCFC-22 (chlorodifluoromethane) were rapidly oxidized and the oxidation occurred in parallel with the oxidation of methane. The maximal HCFC oxidation rates were 0.95 and 0.68 microg g(-1) h(-1) for HCFC-21 and HCFC-22, respectively. Increasing concentrations of HCFCs resulted in decreased methane oxidation rates. However, compared with typical concentrations in landfill gas, relatively high HCFC concentrations were needed to obtain a significant inhibition of methane oxidation. In general, the environmental factors studied influenced the degradation of HCFCs in almost the same way as they influenced methane oxidation. Temperature had a strong influence on the methanotrophic activity giving high Q10 values of 3.4 to 4.1 over the temperature range of 2 to 25 degrees C. Temperature optimum was around 30 degrees C; however, oxidation occurred at temperatures as low as 2 degrees C. A moisture content of 25% w/w yielded the maximum oxidation rate as it allowed good gas transport together with sufficient microbial activity. The optimum pH was around neutrality (pH = 6.5-7.5) showing that the methanotrophs were optimally adapted to the in situ pH, which was 6.9. Copper showed no inhibitory effect when added in relatively high concentrations (up to 60 mg kg(-1)), most likely due to sorption of copper ions to soil particles. At higher copper concentrations the oxidation rates decreased. The oxidation rates for methane, HCFC-21, and HCFC-22 were unaltered in ammonium-amended soil up to 14 mg kg(-1). Higher ammonium concentrations inhibited the oxidation process. The most important parameters controlling oxidation in landfill cover soil were found to be temperature, soil moisture, and methane and oxygen supply.     

Bioconversion of selenate in methanogenic anaerobic granular sludge

The capacity of anaerobic granular sludge to remove selenate from contaminated wastewater was investigated. The potential of different types of granular sludge to remove selenate from the liquid phase was compared to that of suspended sludge and contaminated soil and sediment samples. The selenate removal rates ranged from 400 to 1500 microg g VSS(-1) h(-1), depending on the source of biomass, electron donor, and the initial selenate concentration. The granular structure protects the microorganisms when exposed to high selenate concentrations (0.1 to 1 mM). Anaerobic granular sludge "Eerbeek," originating from a UASB reactor treating paper mill wastewater, removed about 90, 50, and 36% of 0.1, 0.5, and 1 mM of Se, respectively, from the liquid phase when incubated with 20 mM lactate at 30 degrees C and pH 7.5. Selenite, elemental Se (Se(o)), and metal selenide precipitates were the conversion products. Enrichments from the anaerobic granular sludge "Eerbeek" were able to convert 90% of the 10-mM selenate to Se(o) at a rate of 1505 microg Se(VI) g cells(-1) h(-1), a specific growth rate of 0.0125 g cells h(-1), and a yield of 0.083 g cells mg Se(-1). Both microbial metabolic processes (e.g dissimilatory reduction) as well as microbially mediated physicochemical mechanisms (adsorption and precipitation) contribute to the removal of selenate from the Se-containing medium.     

A solid-phase microextraction chamber method for analysis of manure volatiles

Odors from livestock operations are a complex mixture of volatile carbon, sulfur, and nitrogen compounds. Currently, detailed volatiles analysis is both time consuming and requires specialized equipment and methods. This work describes a new method that utilizes a dynamic flux chamber, solid-phase microextraction (SPME), and gas chromatography-mass spectroscopy (GC-MS) to describe and compare the odorous compounds emitted from cattle and swine feces. Evaluation of method parameters produced a protocol for comparing relative emissions based on fixed sample temperature (20 degrees C) and exposed surface area (approximately 523 cm(2)), air flow rates (1 L min(-1) or 16 cm s(-1)), SPME exposure time (5 min), and chamber cleaning procedures (70% ethanol rinse and drying for 30 min at 105 degrees C) to minimize cross-contamination between samples. A variety of volatile organic compounds (VOCs) including alcohols, volatile fatty acids, aromatic ring compounds, ketones, esters, and sulfides were routinely detected and the relative emissions from fresh and incubated (37 degrees C overnight) swine and cattle feces were compared as a measure of potential to produce odorants during manure storage. Differences in the types and relative quantities of volatiles emitted were detected when animal species (cattle or swine), diet, fecal incubation, or sample storage conditions (20, 4, or -20 degrees C) were varied.     

Nitrate reduction in the presence of wüstite

Recent strategies to reduce elevated nitrate concentrations employ metallic Fe0 as a reductant. Secondary products of Fe0 corrosion include magnetite (Fe3O4), green rust [Fe6(OH)12SO4], and wüstite [FeO(s)]. To our knowledge, no studies have been reported on the reactivity of NO3- with FeO(s). This project was initiated to evaluate the reactivity of FeO(s) with NO3- under abiotic conditions. Stirred batch reactions were performed in an anaerobic chamber over a range of pH values (5.45, 6.45, and 7.45), initial FeO(s) concentrations (1, 5, and 10 g L(-1)), initial NO3- concentrations (1, 10, and 15 mM), and temperatures (3, 21, 31, and 41 degrees C) for kinetic and thermodynamic determinations. Suspensions were periodically removed and filtered to measure dissolved nitrogen and iron species. Solid phases were characterized using X-ray diffraction (XRD) and scanning electron microscopy (SEM). Nitrate reduction by FeO was rapid and characterized by nearly stoichiometric conversion of NO3- to NH4+. Transient NO2- formation also occurred. The XRD and SEM results indicated the formation of Fe3O4 as a reaction product of the heterogeneous redox reaction. Kinetics of NO3- reduction suggested a rate equation of the type: -d[NO3-]/dt = k[FeO]0.57[H]0.22[NO3-]1.12 where k = 3.46 x 10(-3) +/- 0.38 x 10(-3) M(-1) s(-1), at 25 degrees C. Arrhenius and Eyring plots indicate that the reaction is surface chemical-controlled and proceeds by an associative mechanism involving a step where both NO3- and FeO(s) bind together in an intermediate complex.     

Removal of copper from aqueous solution by Ascophyllum nodosum immobilised in hydrophilic polyurethane foam

The seaweed Ascophyllum nodosum was pre-treated by successive washes in distilled water and dilute acid, dried, and pulverised to produce particles of <150 microm. These were immobilised during the manufacturing process of Hypol 2002 polymer to form a biomass/polymer matrix that was stable and easy to handle. In making the composite a mixing speed of 360 rpm for 20-30 s with 2% (w/w) addition of surfactant to pre-polymer was found to be ideal. The average pore sizes for different water polymer mixes (expressed as volume ratios) were 1.66 mm +/- 0.98 (ratio 0.75:1), 1.58 mm +/- 0.76 (ratio 1:1), 1.64 mm +/- 0.6 (ratio 1.5:1) and 1.11 mm +/- 0.615 (ratio 2:1). The biomass/polymer was used alongside free native biomass in an initial adsorption experiment using a 0.0315 mmol dm(-3) Cu (II) solution and gave a copper uptake capacity [Formula: see text] of 0.037 mmol Cu g(-1) dry weight seaweed in both cases which represented approximately 85% of total initially available copper. In later adsorption isotherm experiments using Cu concentrations between 0.0315 and 0.944 mmol dm(-3) at pH 5.0 and immobilized biomass over five consecutive adsorption/desorption cycles the biomass/polymer showed an initial lowering of adsorption capacity but stabilised at 0.23 mmol g(-1) dry weight by the third re-use. The q(max) of the immobilised biomass decreased from 0.55 and 0.416 mmol of Cu g(-1) dry weight when pH was lowered from 4.0 to 3.0, and increased from 0.576 mmol g(-1) dry weight (biomass) at 283 K to 0.636 mmol g(-1)(biomass) at 303 K.     

Adsorption studies of hazardous malachite green onto treated ginger waste

Adsorption of malachite green (MG) from aqueous solution onto treated ginger waste (TGW) was investigated by batch and column methods. The effect of various factors such as initial dye concentration, contact time, pH and temperature were studied. The maximum adsorption of MG was observed at pH 9. Langmuir and Freundlich isotherms were employed to describe the MG adsorption equilibrium. The monolayer adsorption capacities were found to be 84.03, 163.9 and 188.6 mg/g at 30, 40 and 50 °C, respectively. The values of thermodynamic parameters like ΔG°, ΔH° and ΔS° indicated that adsorption was spontaneous and endothermic in nature. The pseudo second order kinetic model fitted well in correlation to the experimental results. Rechienberg's equation was employed to determine the mechanism of adsorption. The results indicated that film diffusion was a major mode of adsorption. The breakthrough capacities were also investigated.     

Rice husk ash as an effective adsorbent: evaluation of adsorptive characteristics for Indigo Carmine dye

Present study explored the adsorptive characteristics of Indigo Carmine (IC) dye from aqueous solution onto rice husk ash (RHA). Batch experiments were carried out to determine the influence of parameters like initial pH (pH(0)), contact time (t), adsorbent dose (m) and initial concentration (C(0)) on the removal of IC. The optimum conditions were found to be: pH(0)=5.4, t=8h and m=10.0 g/l. The pseudo-second-order kinetic model represented the adsorption kinetics of IC on to RHA. Equilibrium isotherms were analyzed by Freundlich, Langmuir, Temkin and Redlich-Peterson models using a non-linear regression technique. Adsorption of IC on RHA was favorably influenced by an increase in the temperature of the operation. The positive values of the change in entropy (DeltaS(0)) and heat of adsorption (DeltaH(0)); and the negative value of change in Gibbs free energy (DeltaG(0)) indicate feasible and spontaneous adsorption of IC on to RHA.     

Biological treatment of synthetic wastewater containing 2,4 dichlorophenol (DCP) in an activated sludge unit

Chlorophenol compounds present in many chemical industry wastewaters are resistant to biological degradation because of the toxic effects of such compounds on microorganisms. Synthetic wastewater containing different concentrations of 2,4 dichlorophenol (DCP) was subjected to biological treatment in an activated sludge unit. Effects of feed DCP concentration on COD, DCP, and toxicity removals and on sludge volume index were investigated at a constant sludge age of 10 days and hydraulic residence time (HRT) of 25 h. The Resazurin method based on dehydrogenase activity was used for assessment of toxicity for the feed and effluent wastewater. Percent COD, DCP, and toxicity removals decreased and the effluent COD, DCP, and toxicity levels increased with increasing feed DCP concentrations above 150 mgl(-1) because of inhibitory effects of DCP. Biomass concentration in the aeration tank decreased and the sludge volume index (SVI) increased with feed DCP concentrations above 150 mgl(-1) resulting in lower COD and DCP removal rates. The system should be operated at feed DCP concentrations of less than 150 mgl(-1) in order to obtain high COD, DCP, and toxicity removals.     

Removal of phenol from aqueous solutions by adsorption

Experiments have been conducted to examine the liquid-phase adsorption of phenol from water by silica gel, HiSiv 3000, activated alumina, activated carbon, Filtrasorb-400, and HiSiv 1000. Experiments were carried out for the analysis of adsorption equilibrium capacities and kinetics. The adsorption isotherm model of the Langmuir-Freundlich type was the best to describe adsorption equilibrium data for phenol for the adsorbents studied. Results of kinetic experiments indicated that HiSiv 1000 had the highest rate of adsorption among the adsorbents studied and therefore more detailed studies were carried out with this adsorbent. The influence of particle size, temperature, and thermal regeneration on adsorption of phenol by HiSiv 1000 was evaluated. From particle size experiments it appeared that adsorption capacity of HiSiv 1000 did not change by changing the particle size, but the rate of adsorption decreased considerably by increasing the particle size. The effect of temperature on adsorption was studied by determining equilibrium isotherms for HiSiv 1000 at 25, 40, and 55 degrees C. The results showed that adsorption capacity decreased with increasing temperature. Thermal regeneration of HiSiv 1000 was performed at 360 degrees C. It was observed that adsorption capacity of HiSiv 1000 did not change after 14 regeneration cycles. Equilibrium experiments showed that the adsorption capacities of activated carbon and Filtrasorb-400 were several times higher than that of HiSiv 1000.     

Removal of the hazardous dye rhodamine B through photocatalytic and adsorption treatments

This paper reports on photocatalytic and adsorptive treatment of a hazardous xanthene dye, Rohdamine B, in wastewater. The photocatalytic degradation was carried out in the presence of the catalyst TiO(2) and the effects of pH, concentration of the dye, amount of TiO(2), temperature and electron acceptor H(2)O(2) on the degradation process were observed. It was found that photocatalytic degradation by TiO(2) is an effective, economical and faster mode of removing Rohdamine B from aqueous solutions. Attempts were also made to utilize activated carbon and rice husk as potential adsorbents to remove Rhodamine B from wastewater. The adsorption studies were carried out at 40, 50 and 60 degrees C, and the effects of pH, temperature, amount of adsorbents, concentration of adsorbate, etc., on the adsorption were measured. On the basis of adsorption data the Langmuir and Freundlich adsorption isotherm models were also confirmed. The adsorption isotherm constants thus obtained were employed to calculate thermodynamic parameters like Gibb's free energy, change in enthalpy and entropy. In order to observe the quality of wastewater COD measurements were also carried out before and after the treatments. A significant decrease in the COD values was observed, which clearly indicates that both photocatalytic and adsorption methods offer good potential to remove Rhodamine B from industrial effluents.     

Preparation of novel activated carbons from H2SO4-pretreated corncob hulls with KOH activation for quick adsorption of dye and 4-chlorophenol

Corncob hull was immersed in 25 wt% H(2)SO(4) and was carbonized in an oven at 290 °C for 2h to obtain the char. The char was then activated for 1h at 780 °C by KOH at weight ratio of KOH/char of 2.5, 3.0, and 3.5. SEM photos of the carbons revealed that the cell wall of corncob hull was etched into thin film structure. It was shown that the adsorption isotherms of methylene blue and 4-chlorophenol on the carbons were well fitted by the Langmuir equation. Moreover, the adsorption kinetics could be satisfactorily described by the Elovich equation. The normalized standard deviations are less than 2.8%. The high fraction of adsorption amount adsorbed within 1 min to that at saturation demonstrated the advantage of the prepared activated carbons. The fraction of adsorption amount within 1 min to that at saturation (q(1)/q(mon)) for the adsorption of 4-CP is high up to 0.807. Such quick adsorption behavior was mainly attributed to the presence of the thin film structure of carbons.     

Physicochemical characteristics of animal and municipal wastes decomposed in arid soils

The application of anaerobically processed animal manure to maintain adequate levels of organic matter in arid soils is becoming a common practice. The purpose of this study was to characterize two farm manure products as compared with municipal waste compost (MWC). The anaerobic processing to obtain a biogas manure (BM) product was much faster (25 d) than the aerobic composting of farmyard manure (FYM) (90 d). Drying by three different methods (solar-drying, vacuum-drying at 45 degrees C, and freeze-drying) did not affect the quality of BM. Based on the chemical characteristics, FYM and BM products were comparable, and, containing less ash (30%) and heavy metals (50 mg Pb kg(-1)), seemed superior to MWC that contained 65% ash and 108 mg Pb kg(-1). On the other hand, MWC had higher C content (69.9%), lower acidity (15.04 mol kg(-1)), and higher exothermic peaks (300-460 degrees C) than BM and FYM (50% C, 20 mol kg(-1), and 275-450 degrees C, respectively), thus showing a greater extent of humification. Also, when the organic materials were incubated with arid soils and monitored for mean residence times (MRT), MWC was slightly more resistant to decomposition (MRT 175-180 d) than BM or FYM (MRT 161-166 d). The observed differences, however, were too small to dismiss any of the products as a valuable material for land applications to improve soil quality. In view of the results obtained, MWC may be considered an adequate substitute for BM or FYM, whenever the latter are in short supply.     

Effect of impeller type and mechanical agitation on the mass transfer and power consumption aspects of ASBR operation treating synthetic wastewater

The effect of flow type and rotor speed was investigated in a round-bottom reactor with 5 L useful volume containing 2.0 L of granular biomass. The reactor treated 2.0 L of synthetic wastewater with a concentration of 800 mgCOD/L in 8-h cycles at 30 degrees C. Five impellers, commonly used in biological processes, have been employed to this end, namely: a turbine and a paddle impeller with six-vertical-flat-blades, a turbine and a paddle impeller with six-45 degrees -inclined-flat-blades and a three-blade-helix impeller. Results showed that altering impeller type and rotor speed did not significantly affect system stability and performance. Average organic matter removal efficiency was about 84% for filtered samples, total volatile acids concentration was below 20 mgHAc/L and bicarbonate alkalinity a little less than 400 mgCaCO3/L for most of the investigated conditions. However, analysis of the first-order kinetic model constants showed that alteration in rotor speed resulted in an increase in the values of the kinetic constants (for instance, from 0.57 h(-1) at 50 rpm to 0.84 h(-1) at 75 rpm when the paddle impeller with six-45 degrees -inclined-flat-blades was used) and that axial flow in mechanically stirred reactors is preferable over radial-flow when the vertical-flat-blade impeller is compared to the inclined-flat-blade impeller (for instance at 75 rpm, from 0.52 h(-1) with the six-flat-blade-paddle impeller to 0.84 h(-1) with the six-45 degrees -inclined-flat-blade-paddle impeller), demonstrating that there is a rotor speed and an impeller type that maximize solid-liquid mass transfer in the reaction medium. Furthermore, power consumption studies in this reduced reactor volume showed that no high power transfer is required to improve mass transfer (less than 0.6 kW/10(3)m3).