Difference in ozone uptake in grassland species between open-top chambers and ambient air

Exposure-response data from open-top chamber (OTC) experiments are often directly applied to ambient air (AA) conditions. Because microclimatic conditions are modified and pollutant uptake by plants may differ (i.e. 'chamber effect'), there is concern about the influence of OTCs on these relationships. In addition, AA concentrations are often measured at a height which differs from canopy height and correction for the concentration gradient (i.e. 'gradient effect') is necessary. To quantify the relative contribution of plant characteristics and microclimatic factors to these effects, ozone uptake by horizontal leaves at the top of the canopy was calculated for plants grown in OTCs or AA by using a resistance analogy model. Data from an OTC experiment in 1996/97 for six species typical of productive grasslands were used. Ozone concentration inside OTCs was set equal to the concentration measured at a height of 3 m above ground (C(z(ref))) or at canopy height (C(0)). The gradient effect resulted in a 16-27% lower average C(0) than C(z(ref)), depending on species. The main determinant of the chamber effect was a systematic difference in leaf-to-air vapour pressure deficit between OTCs and AA which affected stomatal resistance and ozone uptake. In case of monocultures both effects were species-specific. In species mixtures the gradient effect differed between mixing ratios, whereas the chamber effect was species-specific. Because of the inter-specific difference in the chamber effect on ozone uptake, it is concluded that ozone effects on species mixtures differ systematically between OTCs and AA. The data underline that extrapolation of ozone flux-response relationships from OTC experiments must be based on canopy-level ozone concentrations, and that these relationships should be applied only to single species under microclimatic conditions similar to those prevailing in the experiment.     

Derivation of ozone flux-yield relationships for lettuce: a key horticultural crop

Ozone flux-response relationships were derived for lettuce, employing a multiplicative approach to model the manner in which stomatal conductance is influenced by key environmental variables, using a dataset collected during field experimentation in Crete and yield-response relationships derived from parallel open-top chamber experiments. Regional agronomic practices were adopted throughout. Computed versus measured data revealed that the derived model explained 51% (P<0.001) of the observed variation in stomatal conductance. Concentration-based indices were compared with flux-based indices. Analyses revealed a significant relationship between accumulated stomatal ozone flux and yield employing flux threshold cut-offs up to 4 nmol m(-2) s(-1). Regressions employing very low or zero flux thresholds resulted in the strongest yield-flux relationships (explaining approximately 80% (P<0.05) of the variation in the dataset).     

Tibouchina pulchra (Cham.) Cogn., a native Atlantic Forest species, as a bio-indicator of ozone: visible injury

Tibouchina pulchra saplings were exposed to carbon filtered air (CF), ambient non-filtered air (NF) and ambient non-filtered air+40 ppb ozone (NF+O3) 8 h per day during two months. The AOT40 values at the end of the experiment were 48, 910 and 12,895 ppb h(-1), respectively, for the three treatments. After 25 days of exposure (AOT40=3871 ppb h(-1)), interveinal red stippling appeared in plants in the NF+O3 chamber. In the NF chamber, symptoms were observed only after 60 days of exposure (AOT40=910 ppb h(-1)). After 60 days, injured leaves per plant corresponded to 19% in NF+O3 and 1% in the NF treatment; and the average leaf area injured was 7% within the NF+O3 and 0.2% within the NF treatment. The extent of leaf area injured (leaf injury index) was mostly explained by the accumulated exposure of ozone (r2=0.89; p<0.05).     

Psidium guajava 'Paluma' (the guava plant) as a new bio-indicator of ozone in the tropics

Psidium guajava 'Paluma' saplings were exposed to carbon filtered air (CF), ambient non-filtered air (NF), and ambient non-filtered air+40ppb ozone (NF+O(3)) 8h per day during two months. The AOT40 values at the end of the experiment were 48, 910 and 12 895ppbh(-1), respectively for the three treatments. After 5 days of exposure (AOT40=1497ppbh(-1)), interveinal red stippling appeared in plants in the NF+O(3) chamber. In the NF chamber, symptoms were observed only after 40 days of exposure (AOT40=880ppbh(-1)). After 60 days, injured leaves per plant corresponded to 86% in NF+O(3) and 25% in the NF treatment, and the average leaf area injured was 45% in NF+O(3) and 5% in the NF treatment. The extent of leaf area injured (leaf injury index) was explained mainly by the accumulated exposure of ozone (r(2)=0.91; p<0.05).     

Critical levels for ozone effects on vegetation in Europe

The evidence of detrimental effects of ozone on vegetation in Europe, and the need to develop international control policies to reduce ozone exposures which are based on the effects of the pollutant, has led to attempts to define so-called critical levels of ozone above which adverse effects on trees, crops and natural vegetation may occur. This review is a critical assessment of the scientific basis of the concepts used to define critical levels for ozone and identifies the key limitations and uncertainties involved. The review focuses on the Level I critical level approach, which provides an environmental standard or threshold to minimise the effects of ozone on sensitive receptors, but does not seek to quantify the impacts of exceeding the critical level under field conditions. The concept of using the AOT (accumulated exposure over a threshold) to define long-term ozone exposure is demonstrated to be appropriate for several economically important species. The use of 40 ppb (giving the AOT40 index) as a threshold concentration gives a good linear fit to experimental data from open-top chambers for arable crops, but it is less certain that it provides the best fit to data for trees or semi-natural communities. Major uncertainties in defining critical level values relate to the choice of response parameter and species; the absence of data for many receptors, especially those of Mediterranean areas; and extrapolation to field conditions from relatively short-term open-top chamber experiments. The derivation of critical levels for long-lived organisms, such as forest trees, may require the use of modelling techniques based on physiological data from experimental studies. The exposure-response data which have been applied to derive critical levels should not be used to estimate the impacts of ozone over large areas, because of the uncertainties associated with extrapolation from the open-top chamber method, especially for forest trees, and because of spatial variation in atmospheric and environmental conditions, which may alter ozone uptake.     

A new flux-orientated concept to derive critical levels for ozone to protect vegetation

The current European critical levels for ozone (O3) to protect crops, natural and semi-natural vegetation and forest trees are based on a relative small number of open-top chamber experiments with a very limited number of plant species. Therefore, the working group "Effects of Ozone on Plants" of the Commission on Air Pollution Prevention of the Association of German Engineers and the German Institute of Standardization reanalysed the literature on O3 effects on European plant species published between 1989 and 1999. An exposure-response relationship for wild plant species and agricultural crops could be derived from 30 experiments with more than 30 species and 90 data points; the relationship for conifer and deciduous trees is based on 20 experiments with nine species and 50 data points. From these relationships maximum O3 concentrations for different risk stages are deduced, below which the vegetation type is protected on the basis of the respective criteria. Because it is assumed that the fumigation concentrations reflect the O3 concentrations at the top of the canopy, i.e. the upper surface boundary of the quasi-laminar layer if the micrometeorological big-leaf approach is applied, the application of these maximum O3 concentrations requires the transformation of O3 concentrations measured at a reference height above the canopy to the effective phytotoxic concentrations at the top of the canopy. Thus, the approach described in this paper is a synthesis of the classical concept of toxicology of air pollutants (critical concentrations) and the more toxicological relevant dose concept.     

Ozone exposure-response relationships for biomass and root/shoot ratio of beech (Fagus sylvatica), ash (Fraxinus excelsior), Norway spruce (Picea abies) and Scots pine (Pinus sylvestris)

Current-year seedlings of beech, ash, Norway spruce and Scots pine were exposed during one growing season to different, but moderate, ozone (O(3)) scenarios representative for Switzerland (50, 85, 100% ambient, 50% ambient+30 nl l(-1)) in open-top chambers (OTCs) and to ambient O(3) concentrations in the field. Biomass significantly decreased with increasing O(3) dose in all species except for spruce. Losses of 25.5% (ash), 17.4% (beech), 9.9% (Scots pine) were found per 10 microl l(-1) h accumulated O(3) exposure over a threshold concentration of 40 nl l(-1) during daylight hours (AOT40). Ratios of root/shoot biomass (RSR) also significantly decreased with increasing AOT40 levels in beech and ash, but not in Norway spruce and Scots pine. The data show that the deciduous species beech and ash were more susceptible to O(3) with respect to RSR and biomass than the coniferous species Norway spruce and Scots pine.     

Ambient ozone and crop loss: establishing a cause-effect relationship

This paper provides the results of a retrospective mathematical analysis of the US NCLAN (National Crop Loss Assessment Network) open-top chamber data. Some 77% of the 73 crop harvests examined, showed no statistically significant yield differences between NF (non-filtered open-top chamber) and AA (chamberless, ambient air) treatments (no easily discernable chamber effects on yield). However, among these cases only seven acceptable examples showed statistically significant yield reductions in NF compared to the CF (charcoal filtered open-top chamber) treatment. An examination of the combined or cumulative hourly ambient O3 frequency distribution for cases with yield loss in NF compared to a similar match of cases without yield loss showed that the mean, median and the various percentiles were all higher (>/= 3 X) in the former in contrast to the latter scenario. The combined frequency distribution of hourly O3 concentrations for the cases with yield loss in NF were clearly separated from the corresponding distribution with no yield loss, at O3 concentrations > 49 ppb. Univariate linear regressions between various O3 exposure parameters and per cent yield losses in NF showed that the cumulative frequency of occurrence of O3 concentrations between 50 and 87 ppb was the best predictor (adjusted R2 = 0.712 and p = 0.011). This analysis also showed that the frequency distribution of hourly concentrations up to 87 ppb O3 represented a critical point, since the addition of the frequency distributions of > 87 ppb O3 did not improve the R2 values. In fact as the frequency of hourly O3 concentrations included in the regression approached 50-100 ppb, the R2 value decreased substantially and the p value increased inversely. Further, univariate linear regressions between the frequencies of occurrence of various O3 concentrations between 50 and 90 ppb and: (a) cases with no yield difference in NF and (b) cases with yield increase in NF compared to the CF treatment (positive effect) provided no meaningful statistical relationship (adjusted R2 = 0.000) in either category. These results support the basis that additional evaluation of the frequency of occurrence of hourly O3] concentrations between 50 and 87 ppb for cases with the yield reductions could provide a meaningful ambient O3 standard, objective or guideline for vegetation.     

PLATIN (plant-atmosphere interaction) II: Co-occurrence of high ambient ozone concentrations and factors limiting plant absorbed dose

There is an ongoing debate as to which components of the ambient ozone (O3) exposure dynamics best explain adverse crop yield responses. A key issue is regarding the importance of peak versus mid-range hourly ambient O3 concentrations. While in this paper the importance of peak atmospheric O3 concentrations is not discounted, if they occur at a time when plants are conducive for uptake, the corresponding importance of more frequently occurring mid-range O3 concentrations is described. The probability of co-occurrence of high O3 concentrations and O3 uptake limiting factors is provided using coherent data sets of O3 concentration, air temperature, air humidity, mean horizontal wind velocity and global radiation measured at representative US and German air quality monitoring sites. Using the PLant-ATmosphere INteraction (PLATIN) model, the significance of the aforementioned meteorological parameters on ozone uptake is examined. In addition, the limitations of describing the O3 exposure for plants under ambient, chamberless conditions by SUM06, AOT40 or W126 exposure indices are discussed.     

Ozone risk assessment for agricultural crops in Europe: Further development of stomatal flux and flux–response relationships for European wheat and potato

Applications of a parameterised Jarvis-type multiplicative stomatal conductance model with data collated from open-top chamber experiments on field grown wheat and potato were used to derive relationships between relative yield and stomatal ozone uptake. The relationships were based on thirteen experiments from four European countries for wheat and seven experiments from four European countries for potato. The parameterisation of the conductance model was based both on an extensive literature review and primary data. Application of the stomatal conductance models to the open-top chamber experiments resulted in improved linear regressions between relative yield and ozone uptake compared to earlier stomatal conductance models, both for wheat (r²=0.83) and potato (r²=0.76). The improvement was largest for potato. The relationships with the highest correlation were obtained using a stomatal ozone flux threshold. For both wheat and potato the best performing exposure index was AF_st6 (accumulated stomatal flux of ozone above a flux rate threshold of 6 nmol ozone m⁻² projected sunlit leaf area, based on hourly values of ozone flux). The results demonstrate that flux-based models are now sufficiently well calibrated to be used with confidence to predict the effects of ozone on yield loss of major arable crops across Europe. Further studies, using innovations in stomatal conductance modelling and plant exposure experimentation, are needed if these models are to be further improved.     

Ozone air pollution and foliar injury development on native plants of Switzerland

The objectives of this study were to examine the foliar sensitivity to ozone exposure of 12 tree, shrub, and herbaceous species native to southern Switzerland and determine the seasonal cumulative ozone exposures required to induce visible foliar injury. The study was conducted from the beginning of May through the end of August during 2000 and 2001 using an open-top chamber research facility located within the Lattecaldo Cantonal Forest Nursery in Canton Ticino, southern Switzerland (600 m asl). Plants were examined daily and dates of initial foliar injury were recorded in order to determine the cumulative AOT40 ppb h ozone exposure required to cause visible foliar injury. Plant responses to ozone varied significantly among species; 11 species exhibited visible symptoms typical of exposures to ambient ozone. The symptomatic species (from most to least sensitive) were Populus nigra, Viburnum lantana, Salix alba, Crataegus monogyna, Viburnum opulus, Tilia platyphyllos, Cornus alba, Prunus avium, Fraxinus excelsior, Ribes alpinum, and Tilia cordata; Clematis spp. did not show foliar symptoms. Of the 11 symptomatic species, five showed initial injury below the critical level AOT40 10 ppmh O3 in the 2001 season.     

Modelling critical levels of ozone for the forested area of austria modifications of the aot40 concept

GOAL, SCOPE AND BACKGROUND: Ozone is the most important air pollutant in Europe for forest ecosystems and the increase in the last decades is significant. The ozone impact on forests can be calculated and mapped based on the provisional European Critical Level (AOT40 = accumulated exposure over a threshold of 40 ppb, 10,000 ppb x h for 6 months of one growing season calculated for 24 h day(-1)). For Norway spruce, the Austrian main tree species, the ozone risk was assessed in a basis approach and because the calculations do not reflect the health status of forests in Austria, the AOT40 concept was developed. METHODS: Three approaches were outlined and maps were generated for Norway spruce forests covering the entire area of Austria. The 1st approach modifies the AOT40 due to the assumption that forests have adapted to the pre-industrial levels of ozone, which increase with altitude (AOTalt). The 2nd approach modifies the AOT40 according to the ozone concentration in the sub-stomata cavity. This approach is based on such factors as light intensity and water vapour saturation deficit, which affect stomatal uptake (AOTsto). The 3rd approach combines both approaches and includes the hemeroby. The pre-industrial ozone level approach was applied for autochthonous ('natural') forest areas, the ozone-uptake approach for non-autochthonous ('altered') forest areas. RESULTS AND DISCUSSION: The provisional Critical Level (AOT40) was established to allow a uniform assessment of the ozone risk for forested areas in Europe. In Austria, where ozone risk is assessed with utmost accuracy due to the dense grid of monitoring plots of the Forest Inventory and because the continuously collected data from more than 100 air quality measuring stations, an exceedance up to the five fold of the Critical Level was found. The result could lead to a yield loss of up to 30-40% and to a severe deterioration in the forest health status. However, the data of the Austrian Forest Inventory and the Austrian Forest Damage Monitoring System do not reflect such an ozone impact. Therefore, various approaches were outlined including the tolerance and avoidance mechanisms of Norway spruce against ozone impact. Taking into consideration the adaptation of forests to the pre-industrial background level of ozone, the AOT40 exceedances are markedly reduced (1st approach). Taking into account the stomatal uptake of ozone, unrealistic high amounts of exceedances up to 10,000 ppb x h were found. The modelled risk does not correspond with the health status and the wood increment of the Austrian forests (2nd approach). Consolidating the forgoing two approaches, a final map including the hemeroby was generated. It became clear that the less natural ('altered') forested regions are highly polluted. This means, that more than half of the spruce forests are endangered by ozone impact and AOT40 values of up to 30,000 ppb x h occur (3rd approach). CONCLUSIONS: The approaches revealed that a plausible result concerning the ozone impact on spruce forests in Austria could only be reached by combining pre-industrial ozone levels, ozone flux into the spruce needles and the hemeroby of forests.     

Simulation of stomatal conductance for Aleppo pine to estimate its ozone uptake

The data from a previous experiment carried out in open-top chambers to assess the effects of ozone (O3) exposure on growth and physiology of Aleppo pine (Pinus halepensis Mill.) were re-assessed to test the performance of the EMEP O3 stomatal conductance model used to estimate tree O3 uptake at a European scale. Aleppo pine seedlings were exposed during three consecutive years to three different O3 treatments: charcoal filtered air, non-filtered air and non-filtered air supplemented with 40 nl l(-1). The results of the model using the default parameterisation already published for Mediterranean conifers showed a poor performance when compared to measured data. Therefore, modifications of g(max), f(min), and new f(VPD), f(temp) and f(phen) functions were developed according to the observed data. This re-parameterisation resulted in a significant improvement of the performance of the model when compared to its original version.     

Visible and microscopic injury in leaves of five deciduous tree species related to current critical ozone levels

Because the current critical level of ozone (O(3)) for forest trees is based only on one species, the responses of five deciduous tree species were differentiated in a climate chamber experiment. The number of symptomatic leaves per tree was significantly increased, and stomatal conductance was decreased under 50% ambient+30 nl l(-1) O(3) as compared to 'normal' senescence at 50% ambient [O(3)]. Species with a high stomatal conductance did not show earlier or more leaf injury symptoms. The additional 30 nl l(-1) O(3) induced specific pectinaceous cell wall protrusions, phenolic cell wall incrustations, tonoplast vesicles, and inhomogeneous, condensed/precipitated phenolic material in the vacuoles. Due to added O(3), cell senescence was accelerated with increased electron-density of the cytoplasm, and initial chloroplast degeneration. The slow degeneration process started in mesophyll cells, and expanded into epidermal and finally guard cells. Because of the large variance in biomass between individuals and species, the current critical level is supported by the assessment of visible leaf symptoms rather than growth reduction.     

Measuring, modelling and testing ozone exposure, flux and effects on vegetation in southern European conditions--what does not work? A review from Italy

Ozone (O3) exposure at Italian background sites exceeds UN/ECE concentration-based critical levels (CLe(c)), if expressed in terms of AOT40. Yet the occurrence of adverse effects of O3 on forests and crops is controversial. Possible reasons include (i) ability of response indicators to provide an unbiased estimate of O3 effects, (ii) setting of current CLe(c) in terms of cut-off value and accumulation level, (iii) response functions adopted to infer a critical level, (iv) environmental limitation to O3 uptake and (v) inherent characteristics of Mediterranean vegetation. In particular, the two latter points suggest that critical levels based on accumulated stomatal flux (CLe(f)) can be a better predictor of O3 risk than CLe(c). While this concept is largely acknowledged, a number of factors may limit its applicability for routine monitoring. This paper reviews levels, uptake and vegetation response to O3 in Italy over recent years to discuss value, uncertainty and feasibility of different approaches to risk assessment.     

Long-term storage of sediments: Implications for sediment toxicity testing

A study using open-top chambers ventilated with ambient or charcoal-filtered air in the vicinity of Lahore, Pakistan, has demonstrated a reduction of 46.7% and 34.8% in the grain yield for two cultivars of winter wheat (Triticum aestivum L.). The 6-h daily mean O(3) concentrations were 25-45 nl litre(-1) and on the basis of experience in North America and Europe, reductions in yield in the present study are substantially greater than might be predicted. The reasons for this discrepancy are discussed, together with implications for the suitability of a simple, relatively cheap, open-top chamber system for developing-country studies on the effects of air pollution on crops.     

Simulations of stomatal conductance and ozone uptake to Norway spruce saplings in open-top chambers

A simulation model was developed to estimate the stomatal conductance and ozone flux to Norway spruce saplings in open-top chambers. The model was parameterized against needle conductance measurements that were made on 4-6-year-old spruce saplings, grown in open-top chambers, in July-September during three different seasons. The spruce saplings were either maintained well watered or subject to a 7-8 week drought period in July-September each year. The simulated conductance showed a good agreement with the measured conductance for the well-watered as well as the drought stress-treated saplings. The simulations were significantly improved when different vapour pressure deficit (VPD) functions were applied for well-watered and drought-stressed spruce saplings. The cumulated ozone uptake which was calculated from the conductance simulations showed less variation between years, compared to the cumulative ozone exposure index AOT40 (accumulated exposure over a threshold of 40 ppb or nl l(-1)) for the corresponding time periods. Measurements in May 1995 demonstrated the occurrence of long-term 'memory-effects' from the drought stress treatments on the conductance. Memory-effects need to be considered when simulation models for stomatal conductance are to be applied to long-lived forest trees under a multiple stress situation.     

Yield loss assessments for cultivars of broccoli, lettuce, and onion exposed to ozone

The effects of the photochemical oxidant air pollutant ozone (O(3)) on growth and yield of three garden crops, broccoli (Brassica oleracea L.), lettuce (Lactuca sativa L.), and onion (Allium cepa L.) were studied in an open-top chamber experiment conducted in the field in southern California. Four cultivars each of leaf lettuce, broccoli, and globe onion were exposed to charcoal-filtered air (CF), non-filtered (NF) air, or NF plus 1.5 times ambient O(3) concentration from 4 weeks after germination in January or February until harvest. Exposures lasted 31 days for lettuce, 55 to 78 days for broccoli, and 105 days for onion. Results showed that despite severe O(3) injury to outer leaves, lettuce yields were not affected by O(3). Broccoli also was resistant to O(3) and no growth reduction was observed at ambient O(3) concentrations. Onions were more susceptible to O(3), but only one cv. 'Rio Bravo' had significant yield losses (ca. 5%) at ambient O(3) levels. These results suggest that, in general, concentrations of O(3) in the winter and spring may be below the threshold for adverse effects on yields of broccoli, lettuce and onion.     

Effects of elevated CO2 concentration on the polyamine levels of field-grown soybean at three O3 regimes

Effects of increased ozone (O3) and carbon dioxide (CO2) on polyamine levels were determined in soybean (Glycine max L. Merr. cv. Clark) grown in open-top field chambers. The chamber treatments consisted of three O3 regimes equal to charcoal filtered (CF), non-filtered (NF), and non-filtered plus 40 nl litre(-1) O3 and CO2 treatments equal to 350, 400 and 500 microl litre(-1) for a total of nine treatments. Leaf samples were taken at three different times during the growing season. Examination of growth and physiological characteristics, such as photosynthesis, stomatal resistance, and shoot weight, revealed that increasing CO2 ameliorated the deleterious effects of increased O3. Results from the initial harvest, at the pre-flowering growth stage (23 days of treatment), showed that increasing O3 at ambient CO2 caused increases in putrescine (Put) and spermidine (Spd) of up to six-fold. These effects were lessened with increased CO2. Elevated CO2 increased polyamines in plants treated with CF air, but had no effect in the presence of ambient or enhanced O3 levels. Leaves harvested during peak flowering (37 days of treatment) showed O3-induced increases in Put and Spd at ambient CO2 concentrations. However, increased CO2 levels inhibited this response by blocking the O3-induced polyamine increase. Leaves harvested during the pod fill stage (57 days of treatment) showed no significant O3 or CO2 effects on polyamine levels. Our results demonstrate that current ambient O3 levels induce the accumulation of Put and Spd early in the growing season and that further increases in O3 could result in even greater polyamine increases. These results are consistent with a possible antiozonant function for polyamines. The ability of increased CO2 to protect soybeans from O3 damage, however, does not appear to involve polyamine accumulation.     

A Wind Tunnel Study to Design Large,Open-top Chambers for Whole-tree Pollutant Exposure Experiments

A wind tunnel study was conducted to determine the optimal design features of a large, open-top chamber, as needed for pollution exposure studies on mature trees. An optimally-designed, open-top chamber must minimize the incursion of ambient air through its opening and maintain a uniform treatment concentration throughout the chamber. The design features of interest are the diameter and height of the chamber and the deflection angle and opening size of any frustum that may be mounted on top of a model chamber.

Design specifications depend on the turbulence regime about the chamber, which is influenced by the nature of the surrounding vegetation. Consequently, our investigation was performed on scale-model, open-top chambers in a wind tunnel populated with a model coniferous forest. Turbulence measurements demonstrated the similarity between the turbulence regime of the model and a natural forest. A hydrocarbon tracer was injected into the wind tunnel flow to characterize chamber performance.

The main design features of open-top chambers are the velocity of air exiting through the top and the relationship between the length scale of the turbulence and the diameter of the chamber opening. As exit velocities increase, the proportion of eddies with sufficient force to penetrate into the chamber decrease. Therefore, for equal volumetric air flows, smaller opening sizes increase the exit velocities and reduce the number and extent of ambient air incursions. Almost total exclusion of ambient air is achieved as the exit velocity of the air exceeds the magnitude of one standard deviation of the vertical wind velocity measured at the chamber top. The incursion of ambient air is also reduced when the diameter of the chamber opening is smaller than the characteristic length scale of the turbulence, a measure of mean eddy size.

Frusta deflect air flow over the chamber. Three prototypes, with 30?, 45? and 60-degree angles were tested. A 30-degree frustum slightly improves the performance of the chamber and is more effective in preventing ambient air from entraining into the chamber opening than frusta with either a 45? or 60-degree angle. A flatter frustum allows for a smoother transition in the wind velocity streamline and is less apt to cause wake turbulence, as is the case with steeper frusta.

Knowledge of the turbulence characteristics of plant canopies are readily available in the literature and can aid scientists and engineers in designing the optimal chamber and frusta dimensions for their particular application. Therefore, the empirical approach to chamber design can be avoided, and substantial savings can be realized.