Fate of CL-20 in sandy soils: degradation products as potential markers of natural attenuation

Hexanitrohexaazaisowurtzitane (CL-20) is an emerging explosive that may replace the currently used explosives such as RDX and HMX, but little is known about its fate in soil. The present study was conducted to determine degradation products of CL-20 in two sandy soils under abiotic and biotic anaerobic conditions. Biotic degradation was prevalent in the slightly acidic VT soil, which contained a greater organic C content, while the slightly alkaline SAC soil favored hydrolysis. CL-20 degradation was accompanied by the formation of formate, glyoxal, nitrite, ammonium, and nitrous oxide. Biotic degradation of CL-20 occurred through the formation of its denitrohydrogenated derivative (m/z 393 Da) while hydrolysis occurred through the formation of a ring cleavage product (m/z 156 Da) that was tentatively identified as CH₂N-C(N-NO₂)-CHN-CHO or its isomer N(NO₂)CH-CHN-CO-CHNH. Due to their chemical specificity, these two intermediates may be considered as markers of in situ attenuation of CL-20 in soil.     

Physiological effects of arsenate on transplant thalli of the lichen Pyxine cocoes (Sw.) Nyl

Introduction

The changes in photosynthetic pigments, chlorophyll fluorescence, protein content, and antioxidant enzymes were investigated in a foliose lichen Pyxine cocoes, which was subjected to increasing concentrations of arsenate.

Methods

The arsenate concentrations of 10, 25, 50, 75, 100, and 200???M were sprayed every alternate day on the lichen thallus. The thalli were then harvested on 10, 20, 30, and 45?days.

Results

The quantity of photosynthetic pigments exhibited a decreasing trend till 20?days but increased from 30?days onwards. Concomitantly, chlorophyll fluorescence also showed a decreasing trend with increasing arsenic treatment duration as well as concentration. The higher concentration of arsenate was found to be deleterious to the photosynthesis of lichen as the chlorophyll fluorescence and the amount of pigments decreased significantly. The protein content of lichen increased uninterruptedly as the concentration of arsenate as well as duration of treatment increased. The activities of superoxide dismutase and ascorbate peroxide increased initially at lower concentration of arsenate but declined at higher concentrations and longer duration of treatment.

Conclusions

The catalase activity was found to be most susceptible to arsenate stress as its activity started declining from very beginning of the experiment. P. cocoes also proved to be an excellent accumulator of arsenate whose concentration increased in the thallus corresponding to its increase in the treatment and duration. Thus, it can be utilized for active biomonitoring of arsenic pollution.     

Evaluation of olive oil mill wastewater toxicity on spinach

Background, aim, and scope

Olive oil mill wastewater (OMW), a by-product of the olive oil extraction process, is annually produced in huge amounts in olive-growing areas and represents a significant environmental problem in Mediterranean areas. We studied the impact of OMW dilutions (1:20 and 1:10) on spinach plants in order to evaluate OMW dilutions as a low-cost alternative method for the disposal of this waste.

Materials and methods

The effects of OMW dilutions were evaluated on seed germination, shoot and root elongation, biomass production, nutrient uptake and translocation, ascorbic acid content, polyphenols, photosynthetic pigments, and photosynthetic performance of spinach.

Results

Plant biomass was more affected than plant height and total chlorophyll; carotenoid and ascorbic acid content progressively decreased with decreasing OMW dilution. Exposure to both OMW dilutions resulted in overaccumulation of total polyphenols, which were negatively correlated to plant biomass and nutrients. Nutrient (Fe, Ca, and Mg) content was insufficient leading to reduced growth. Water use efficiency decreased mainly due to decreased CO₂ assimilation rate rather than to a decline of transpiration rate. Disturbances in photosystem II (PSII) photochemical efficiency could be better envisaged by the ratio between variable fluorescence and initial fluorescence (Fv/Fo), which showed much greater amplitude than the maximal photochemical efficiency of PSII photochemistry (Fv/Fm).

Conclusions

From the data obtained, it is suggested that 1:20 OMW dilutions are still phytotoxic and that higher OMW dilutions should be used in order to use this waste for the irrigation of spinach plants.     

Short-term effects of diesel fuel on rhizosphere microbial community structure of native plants in Yangtze estuarine wetland

Purpose

In this work, short-term effects of diesel fuel on Huangpu?CYangtze estuarine wetland soil microbial community structure were studied under simulated conditions through phospholipid fatty acids (PLFAs) analysis. Four native plant species, bulrush (Scirpus tripueter), galingale (Cyperus rotundus), wildrice (Zizania latifolia), and reed (Phragmites australis) were tested in the experiments.

Method

In the pot experiment, 20?g rhizosphere soils were mixed with 20?g diesel-blended soils. The concentration of total petroleum hydrocarbon was 16,000?mg/kg. All pots were incubated for 14?days in dark at 28°C and watered with 12?mL sterile distilled water to keep a liquid level. Microbial activity of the samples was assessed by hydrolysis of fluorescein diacetate. Measurements of soil PLFAs and analysis on gas chromatography were performed.

Results

The microbial activity in the samples of reed was highest after the exposure. In all samples, the common PLFA was straight-chain saturated fatty acid (SFA) and monounsaturated fatty acid (MUFA). After the exposure the relative abundance of MUFA and polyunsaturated fatty acid decreased by 20%, and the relative abundance of straight-chain SFA increased by 20%. The results of diversity and PCA indicated that the effect of diesel pollutant on the microbial community was far stronger than the root effect and the reed roots enhanced the tolerance of soil microorganisms to diesel significantly.

Conclusions

All results showed that the soil microbial community structure differed significantly with the exposure to diesel. In reed rhizosphere, the soil microorganisms exhibited a strong resistance to diesel fuel. It confirmed that the root of reed improved the biodegradation ability of soil microorganisms for diesel pollutants and they could be reasonably matched to cure and restore the ecological environment of oil-contaminated wetlands.     

Extractability of water-soluble soil organic matter as monitored by spectroscopic and chromatographic analyses

Purpose

Cold and hot water processes have been intensively used to recover soil organic matter, but the effect of extraction conditions on the composition of the extracts were not well investigated. Our objective was to optimize the extraction conditions (time and temperature) to increase the extracted carbon efficiency while minimizing the possible alteration of water extractable organic matter of soil (WEOM).

Method

WEOM were extracted at 20°C, 60°C, or 80°C for 24?h, 10?C60?min, and 20?min, respectively. The different processes were compared in terms of pH of suspensions, yield of organic carbon, spectroscopic properties (ultraviolet?Cvisible absorption and fluorescence), and by chromatographic analyses.

Results

For extraction at 60°C, the time 30?min was optimal in terms of yield of organic carbon extracted and concentration of absorbing and fluorescent species. The comparison of WEOM 20°C, 24?h; 60°C, 30?min; and 80°C, 20?min highlighted significant differences. The content of total organic carbon, the value of specific ultraviolet absorbance (SUVA₂₅₄), the absorbance ratio at 254 and 365?nm (E ₂/E ₃), and the humification index varied in the order: WEOM (20°C, 24?h)?Conclusions For the soil chosen, extraction at 60°C for 30?min is the best procedure for enrichment in organic chemicals and minimal alteration of the organic matter.     

Monitoring heavy metal pollution by aquatic plants

Introduction

The copper bioaccumulation by the floating Lemna minor and by the completely submerged Ranunculus tricophyllus as a function of exposure time and copper concentration was studied, with the aim of proposing these species as environmental biosensors of the water pollution.

Results

The results show that both these aquatic angiosperms are good indicators of copper pollution because the copper uptake is the only function of metal concentration (water pollution).

Conclusion

Uptake behavior is reported as a function of the time and concentration, based on the results of a 3-year study. Kinetic evaluations are proposed.     

Aquatic ecotoxicity assessment of a new natural formicide

Background, aim and scope

Agrochemicals could reach aquatic ecosystems and damage ecosystem functionality. Natural formicide could be an alternative to use in comparison with the more toxic formicides available on the market. Thus, the objective of this study was to assess the ecotoxicity of the new natural formicide Macex? with a battery of classical aquatic ecotoxicity tests.

Material and methods

Bacteria (Aliivibrio fischeri), algae (Pseudokirchneriella subcapitata), hydra (Hydra attenuata), daphnids (Daphnia magna), and fish (Danio rerio) tests were performed in accordance with international standardized methodologies.

Results

In the range of formicide concentrations tested (0.03 to 2.0?g?L^?1) EC₅₀ values varied from 0.49 to >2.0?g?L^?1, with P. subcapitata being the most sensitive species and H. attenuata and D. rerio the most tolerant species to this product in aqueous solutions.

Conclusions

This new formicide preparation can be classed as a product of low toxicity compared to the aquatic ecotoxicity of the most common commercialized formicides.     

Isolation and characterization of 3-nitrophenol-degrading bacteria associated with rhizosphere of Spirodela polyrrhiza

Introduction

The accelerated biodegradation of 3-nitrophenol (3-NP) in the rhizosphere of giant duckweed (Spirodela polyrrhiza) was investigated.

Materials and methods

Biodegradation of 3-nitrophenol in the rhizosphere of a floating aquatic plant, S. polyrrhiza, was investigated by using three river water samples supplemented with 10?mg?l^?1 of 3-NP. Isolation and enrichment culture of 3-NP-degrading bacteria were performed in basal salts medium containing 3-NP (50?mg?l^?1). The isolated strains were physiologically and phylogenetically characterized by using an API20NE kit and 16S rRNA gene sequencing.

Results and discussion

Accelerated removal of 3-NP (100%) was observed in river water samples with S. polyrrhiza compared with their removal in plant-free river water. Also, 3-NP persisted in an autoclaved solution with aseptic plants, suggesting that the accelerated 3-NP removal resulted largely from degradation by bacteria inhabiting the plant rather than from adsorption and uptake by the plant. We successfully isolated six and four strains of 3-NP-degrading bacteria from the roots of S. polyrrhiza and plant-free river water, respectively. Phylogenetic analysis based on 16S rRNA gene divided the 3-NP-degrading bacteria into two taxonomic groups: the genera Pseudomonas and Cupriavidus. The strains belonging to the genus Cupriavidus were only isolated from the roots of duckweed. All strains isolated from the roots utilized 3-NP (0.5?mM) as a sole carbon and energy source, indicating that they could have contributed to the accelerated degradation of 3-NP in the rhizosphere of S. polyrrhiza.

Conclusions

The rhizoremediation using S. polyrrhiza and its rhizosphere bacteria can be an effective strategy for cleaning up the 3-NP-contaminated surface waters.     

Harvesting of Chlorella sp. using hollow fiber ultrafiltration

Introduction

The suitability of the application of ultrafiltration (UF) to harvest Chlorella sp. from the culture medium was examined. We investigated the effects of two improved UF system, forward air?Cwater flushing and backwash with permeate, on the concentration process.

Materials and methods

Backwash with permeate was selected as an optimization of the improved UF system, which was more effective for permeate flux recovery. Moreover, the hollow fiber UF system by adding periodical backwash with permeate was examined for Chlorella sp. harvesting.

Results and discussion

It was found that Chlorella sp. could be concentrated with high recovery in a lab-scale experiment. An overall algal biomass recovery of above 90% was achieved when the volume concentration factor was 10. For an original biomass of 1.3?±?0.05?g/L, 1?min backwash followed by 20?min forward concentrating was more effective, which resulted in a recovery of 94% and a high average flux of 30.3?L/m²/h. In addition, the algal recovery was highly correlated to the volume concentration factor and the initial biomass. A high concentration factor or a high initial biomass resulted in a low biomass recovery.     

Reference gene selection for qPCR in mussel, Mytilus edulis, during gametogenesis and exogenous estrogen exposure

Purpose

The aim of this study is to develop a normalization method for real-time PCR data by analyzing the most stably expressed control genes in mussel (Mytilus edulis) reproductive tissue.

Methods

To facilitate this, six candidate genes, including several commonly used in the literature, were investigated in mussels at different stages of gametogenesis and following experimental exposure to a model estrogen (17b-estradiol). GeNorm and NormFinder softwares were employed to assess the stability of the reference genes.

Results

Our results demonstrate that the most stable reference genes are not the same in mussels at different stages of gametogenesis and in experimentally E2-exposed mussels. Interestingly, HEL (helicase) and ACT (actin) mRNA expression levels were most affected by the stage of gametogenesis and yet, in molluscan studies, ACT is possibly the most frequently used reference gene.

Conclusions

We demonstrate that the experimental results are highly dependent on the reference gene chosen and that statistically significant contrasting differences between sample groups are present or absent depending on the reference gene employed.     

Efficient biosorption of chromium(VI) ion by dry Araucaria leaves

Background

In this paper, batch removal of hexavalent chromium from aqueous solutions by Araucaria heterophylla leaves was investigated. The batch experiments were conducted to study the adsorption of metal species and effect of different pH, contact time, metal concentration, biosorbent concentration, and adsorption capacity.

Method

Freundlich and Langmuir??s isotherm model were used to describe the adsorption behavior, and the experimental results fitted Freundlich model well.

Results

The adsorption efficiency observed for all chromium concentrations, i.e., 1, 3, 5, and 10?mg/L was 100% and the equilibrium was achieved in 30?min for 1 and 3?mg/L, whereas for 5 and 10?mg/L, it was less than 60?min. FTIR spectra was taken to identify functional groups involved in the biosorption.

Conclusion

Thus, Araucaria leaves can be considered as one of the cheap and efficient biosorbent for toxic hexavalent chromium removal from natural or wastewaters.     

BOD biosensors for pulp and paper industry wastewater analysis

Introduction

Two semi-specific microbial biosensors were constructed for the analysis of biochemical oxygen demand (BOD) in high-cellulose-content pulp and paper industry wastewaters. The biosensors were based on living cells of Bacillus subtilis and Paenibacillus sp. immobilized in an agarose gel matrix. Semi-specific microorganisms were isolated from various samples (decaying sawdust and rabbit manure) and were chosen based on their ability to assimilate cellulose.

Materials &; methods

The biosensors were calibrated with the Organization for Economic Cooperation and Development synthetic wastewater, and measurements with different wastewaters were conducted.

Results

The response time of biosensors using the steady-state method was 20?C25 min, and the service life of immobilized microorganisms was 96 days. Detection limit was 5 mg/l of BOD₇ while linear ranges extended up to 55 and 50 mg/l of the BOD₇ for B. subtilis- and Paenibacillus sp.-based biosensors, respectively. Repeatability and reproducibility of both biosensors were within the limits set by APHA??less than 15.4%. In comparison, both biosensors overestimated the BOD₇ values in paper mill wastewaters and underestimated the BOD₇ in aspen pulp mill wastewater.

Conclusions

The semi-specific biosensors are suitable for the estimation of organic pollution derived from cellulose, while the detection of pollution derived from tannins and lignins was minor. Better results in terms of accuracy and repeatability were gained with Paenibacillus sp. biosensor.     

Temperature influence on silver nanoparticles inhibitory effect on photosystem II photochemistry in two green algae, Chlorella vulgaris and Dunaliella tertiolecta

Purpose

In this study, the effect of silver nanoparticles (AgNPs) on the photosynthetic performance of two green algae, Chlorella vulgaris and Dunaliella tertiolecta, was investigated at 25°C and 31°C.

Methods

To induce AgNPs effect, algal cells were exposed for 24?h to concentrations varying from 0 to 10?mg/L. The polyphasic OJIP fluorescence transient was used to evaluate photosystem II (PSII).

Results

We show that growth media and temperature had different effects in AgNPs agglomerates formation and Zeta potential. When temperature conditions change, inhibitory effect of AgNPs also undergoes changes. Increase of temperature induced higher altering effects to PSII quantum yield, primary photosynthetic electron transport, and consequently higher decrease of total photosynthetic performance if compared to AgNPs effect alone. AgNPs has a negative effect on D. tertiolecta compared to C. vulgaris.

Conclusion

We conclude that temperature tends to enhance the toxic effects on aquatic alga and these alterations might have serious consequences on ecosystem equilibrium and aquatic plant communities.     

Evaluation of environmental impact produced by different economic activities with the global pollution index

Introduction

The paper analyses the environment pollution state in different case studies of economic activities (i.e. co-generation electric and thermal power production, iron profile manufacturing, cement processing, waste landfilling, and wood furniture manufacturing), evaluating mainly the environmental cumulative impacts (e.g. cumulative impact against the health of the environment and different life forms).

Materials and methods

The status of the environment (air, water resources, soil, and noise) is analysed with respect to discharges such as gaseous discharges in the air, final effluents discharged in natural receiving basins or sewerage system, and discharges onto the soil together with the principal pollutants expressed by different environmental indicators corresponding to each specific productive activity. The alternative methodology of global pollution index (I _GP ^* ) for quantification of environmental impacts is applied.

Results and discussion

Environmental data analysis permits the identification of potential impact, prediction of significant impact, and evaluation of cumulative impact on a commensurate scale by evaluation scores (ES_i) for discharge quality, and global effect to the environment pollution state by calculation of the global pollution index (I _GP ^* ).

Conclusions

The I _GP ^* values for each productive unit (i.e. 1.664?C2.414) correspond to an ??environment modified by industrial/economic activity within admissible limits, having potential of generating discomfort effects??. The evaluation results are significant in view of future development of each productive unit and sustain the economic production in terms of environment protection with respect to a preventive environment protection scheme and continuous measures of pollution control.     

Comparison of two wild rodent species as sentinels of environmental contamination by mine tailings

Background

Contamination with heavy metals is among the most hazardous environmental concerns caused by mining activity. A valuable tool for monitoring these effects is the use of sentinel organisms. Particularly, small mammals living inside mine tailings are an excellent study system because their analysis represents a realistic approach of mixtures and concentrations of metal exposure.

Purpose

We analyzed metal tissue concentrations and DNA damage levels for comparison between genders of a sentinel (Peromyscus melanophrys) and a nonsentinel (Baiomys musculus) species. Also, the relationship between DNA damage and the distance from the contamination source was evaluated.

Methods

This study was conducted in an abandoned mine tailing at Morelos, Mexico. Thirty-six individuals from both species at the exposed and reference sites were sampled. Metal concentrations in bone and liver of both species were analyzed by atomic absorption spectrophotometry, and DNA damage levels were assayed using the alkaline comet assay.

Results

In general, concentrations of zinc, nickel, iron, and manganese were statistically higher in exposed individuals. A significant effect of the organ and the site on all metal tissue concentrations was detected. Significant DNA damage levels were registered in the exposed group, being higher in B. musculus. Females registered higher DNA damage levels than males. A negative relationship between distance from the mine tailing and DNA damage in B. musculus was observed.

Conclusions

We consider that B. musculus is a suitable species to assess environmental quality, especially for bioaccumulable pollutants??such as metals??and recommend that it may be considered as a sentinel species.     

Exposure to toxic waste containing high concentrations of hydrogen sulphide illegally dumped in Abidjan, C?te d’Ivoire

Introduction

On August 2006, a cargo ship illegally dumped 500?t of toxic waste containing high concentrations of hydrogen sulphide in numerous sites across Abidjan. Thousands of people became ill. Seventeen deaths were associated with toxic waste exposure.

Materials and methods

This study reports on environmental and health problems associated with the incident. A cross-sectional transect study was conducted in five waste dumping site areas.

Results

Of the households, 62.1% (n?=?502) were exposed to the effects of the pollutants and 51.1% of the interviewed people (n?=?2,368) in these households showed signs of poisoning. Most important symptoms were cough (37.1%), asthenia (33.1%), pruritus (29.9%) and nausea (29.1%).

Discussion

The health effects showed different frequencies in the five waste impact sites. Among the poisoned persons, 21.1% (n?=?532) presented symptoms on the survey day (i.e., 4?months after incident). Transect sampling allowed to determine a radius of vulnerability to exposure of up to 3?km from the point of toxic waste disposal.

Conclusion

The area of higher vulnerability is influenced by various environmental factors, such as size and severity of pollution site, duration of toxic waste pollution on the impact site and locally climatic conditions. The surveillance of effects on environment and human health is warranted to monitor the development.     

Impact of molybdenum nanoparticles on survival,activity of enzymes,and chemical elements in <Emphasis Type="Italic">Eisenia fetida</Emphasis> using test on artificial substrata

The influence of molybdenum oxide nanoparticles (MoO₃) on the growth and survival of Eisenia fetida was established. The activity of antioxidant enzymes and changes in concentration of molybdenum in the body of E. fetida were determined. The degree of bacterial bioluminescence inhibition in extracts of substrates and worm was studied using luminescent strain Escherichia coli K12 TG1. The enzymatic activity of substrates before and after exposure with nanoparticles and worms was assessed. Nanoparticles have concentrations of 10, 40, and 500 mg/kg of dry matter, and substrata are made of artificial soil (substrate A) and microcrystalline cellulose (substrate B). Spherical nanoparticles MoO₃, yellow in color, with size 92?±?0.3 nm, Z-potential 42?±?0.52 mV, molybdenum content 99.8 mass/%, and specific area 12 m²/g were used in the study. A significant decrease by 23.3 % in weight was registered (for MoO₃ NPs at 500 mg/kg) on substrate A (p?≤?0.05). On substrate B, the maximum decrease in weight by 20.5, 33.3, and 16.9 % (p?≤?0.05) was registered at a dose of 10, 40, and 500 mg/kg, respectively; mortality was from 6.6 to 73 %. After the assessment of bacterial bioluminescence inhibition in substrates A and B (extracts) and before worms were put, the toxicity of substrates was established at doses of 40 and 500 mg/kg, expressed in inhibitory concentration (IC) 30 and IC 50 values. Comparatively, on days 7 and 14, after exposure in the presence of E. fetida, no inhibition of bioluminescence was registered in extracts of substrates A and B, indicating the reduction in toxicity of substrates. The initial content of molybdenum in E. fetida was 0.9?±?0.018 mg/kg of dry matter. The degree of molybdenum accumulation in worm tissue was dependent on the dose and substrate quality. In particular, 2–7 mg/kg of molybdenum accumulated from substrate A, while up to 15 kg/kg of molybdenum accumulated from substrate B (day 7). Molybdenum concentration decreased by 64.8 and 57.4 % at doses 40 and 500 mg/kg, respectively, on day 14. The reaction of antioxidant enzymes was shown in an insignificant increase of glutathione reductase (GSR) and catalase (CAT) at concentrations of 10 and 40 mg/kg in substrate A, followed by the subsequent reduction of their activity at the dose of 500 mg/kg MoO₃. The activity of GSR in substrate B against the presence of MoO₃ nanoparticles decreased, with significant difference of 33.5 % (p?≤?0.05) at the dose of 500 mg/kg compared with untreated soil. In experiments with substrate A, an increase of catalase activity was registered for the control sample. The presence of MoO₃ nanoparticles at the concentration of 10 mg/kg in the environment promoted enzymatic activity on days 7 and 14, respectively. A further increase of nanoparticle concentration resulted in the decrease of catalase activity with a minimum value at the concentration of MoO₃ of 500 mg/kg. In the experiment with substrate B at the concentration of MoO₃ nanoparticles of 40 mg/kg, enzymatic activity increases on day 7 of exposure. However, the stimulating effect of nanoparticles stops by day 14 of the experiment and further catalase activity is dose dependent with the smallest value in the experiment with MoO₃ having the concentration of 500 mg/kg.     

Effects of perinatal exposure to bisphenol A and di(2-ethylhexyl)-phthalate on gonadal development of male mice

Purpose

In this study, we investigated the effects of maternal transfer of bisphenol A (BPA) and di(2-ethylhexyl) phthalate (DEHP) during gestational and weaning periods on gonadal development of male offspring.

Methods

Pregnant CD-1 mice were administered by gavages in corn oil with 0.1, 1, or 10 mg/kg/day of BPA and DEHP from gestational days (GD1?C21) to the weaning period (postnatal days (PND) 1?C21).

Results

Our data indicated that the exposure significantly reduced the male-to-female sex ratio and the sizes of the gonads of male pups as recorded at PND15. The testes of the perinatally exposed male pups were developed less and the expression levels of testicular anti-mullerian hormone, androgen receptor, cyclin A, and StAR were significantly lesser than the control male pups. The less developed testes were accompanied with significant reductions in the expression levels of Gnrh and Fsh at the hypothalamic?Cpituitary levels. The negative effects were found to be persistent in the sexually mature pups at PND42.

Conclusion

Our data reveal that the maternal transfer of BPA and DEHP may impose negative influence on the development and functions of the reproductive system of male pups.     

Thermophilic desulfurization of dibenzothiophene and different petroleum oils by Klebsiella sp. 13T

Purpose

Biodesulfurization (BDS) has the potential to desulfurize dibenzothiophene (DBT) and its alkylated derivatives, the compounds that are otherwise refractory to hydrodesulfurization (HDS). Thermophilic microorganisms are more appropriate to be used for BDS applications following HDS. The aim of the present study was to isolate a thermophilic microorganism and to explore its commercial relevance for BDS process.

Methods

The desulfurizing thermophilic strain was isolated and enriched from various soil and water samples using sulfur free medium (SFM) supplemented with DBT. Microbiological and genomic approach was used to characterize the strain. Desulfurization reactions were carried out using DBT and petroleum oils at 45°C followed by different analytical procedures.

Results

We report the isolation of a thermophilic bacterium Klebsiella sp. 13T from contaminated soils collected from petroleum refinery. HPLC analysis revealed that Klebsiella sp. 13T could desulfurize DBT to 2-hydroxybiphenyl (2-HBP) at 45°C through 4S pathway. In addition, adapted cells of Klebsiella sp. 13T were found to remove 22?C53% of sulfur from different petroleum oils with highest sulfur removal from light crude oil.

Conclusion

Klebsiella sp. 13T is a potential candidate for BDS because of its thermophilic nature and capability to desulfurize petroleum oils.     

Biosorption of zinc and copper from aqueous solutions by two freshwater green microalgae Chlorella pyrenoidosa and Scenedesmus obliquus

Purpose

The objective of this study was to determine the removal of zinc and copper by two freshwater green microalgae Chlorella pyrenoidosa and Scenedesmus obliquus and to investigate changes of algal ultrastructure and photosynthetic pigment.

Methods

Algal cells were exposed for 8 days to different initial zinc or copper concentrations. Heavy metal concentrations were detected by an atomic absorption spectrophotometer. Algal growth, ultrastructure, and photosynthetic pigment were analyzed by a microplate reader, transmission electron microscope, and spectrophotometer, respectively.

Results

Low zinc and copper concentrations induced increase in algal growth, whereas application of high zinc and copper concentrations suppressed the growth of both algae. High metal concentrations also decreased the photosynthetic pigments and destroyed algal cell ultrastructure. The zinc removal efficiency by both algae increased rapidly during the first day and thereafter remained nearly constant throughout the experiment. The copper removal efficiency by both algae increased slowly during the whole experimental periods. In all cultures, the quantity of both metals removed intracellularly was much lower than the adsorbed quantity on the cell surface.

Conclusions

Both strains of the microalgae had proven effective in removing zinc and copper from aqueous solutions, with the highest removal efficiency being near 100%. In addition, C. pyrenoidosa appeared to be more efficient than S. obliquus for removing copper ions. On the contrary, S. obliquus appeared to be more efficient than C. pyrenoidosa for removing zinc ions.