TiO_2/EP光催化降解水体中微污染磺胺嘧啶的研究

制备了膨胀珍珠岩(EP)为载体的TiO2催化剂(TiO2/EP),对使用较为广泛的抗生素磺胺嘧啶(SDZ)进行了光催化降解研究,探讨了TiO2的负载量、溶液的初始浓度、初始pH、无机离子(HCO3-、SO42-和Cl-)和腐殖酸(HA)对SDZ降解效果的影响。结果表明:SDZ的光催化降解符合一级反应动力学方程;当TiO2最佳负载量为20 wt%,SDZ浓度为5 mg/L,pH=6.7,紫外光照射强度为1 000μW/cm2,反应时间为45 min时,SDZ的降解率达到96%;HCO3-在低浓度时能促进SDZ的光催化降解,高浓度时促进作用不明显;SO42-和Cl-对SDZ的光催化降解有轻微的抑制作用;HA对SDZ光催化降解有显著的抑制作用,浓度越高,抑制作用越强。UV-TiO2/EP是一种去除水体中微污染SDZ的有效方法。     

水体中常见无机阴离子对TiO2薄膜光催化降解甲醛的影响

选择了5种水体中常见的阴离子（Cl^-,SO4^2-,HPO4^2-/HPO4^2-,HCO3^-/CO3^2-和NO3^-）,分别考查了其对TiO2薄膜光催化降解模拟甲醛废水的反应速率的影响;从上述离子的光吸收,对.OH的捕获及其生成的相应的无机自由基的氧化作用以及与甲醛的竞争吸附3个方面讨论了上述离子影响TiO2薄膜光催化降解模拟甲醛废水的反应速率的原因。结果表明,HCO3^-/CO3^2-对TiO2薄膜光催化降解甲醛具有抑制作用,Cl^-和SO4^2-的影响不大,H2PO4^-/HPO4^2-和NO3-具有促进作用。造成上述结果的主要原因是HCO3^-/CO2^3-具有很强的.OH捕获作用;Cl^-,SO4^2-对.OH捕获作用以及竞争吸附都较弱;H2PO4^-/HPO4^2-在TiO2表面具有较强的吸附能力,释放出的H＋起到了酸催化剂的作用;NO3^-在紫外光的照射下可以产生.OH,此外NO3^-作为电子受体而降低了TiO2表面光生电子和空穴的复合几率。     

SO_4~（2-）/TiO_2光催化降解苯酚

以工业硫酸氧钛为原料水解制得SO42-/TiO2光催化剂,并以苯酚为目标降解物,考察了SO24-/TiO2的光催化性能。结果表明：随着SO42-/TiO2制备过程中焙烧温度的升高,其光催化活性逐渐增加,650℃焙烧获得的SO24-/TiO2的光催化活性最好,此后再升高温度会因催化剂中硫的挥发而下降;在确定苯酚原液初始浓度为50 mg/L条件下,SO42-/TiO2的光催化降解苯酚的最佳工艺条件为反应时间2 h、苯酚pH为7、催化剂用量1 g/L。XRD、SEM和FTIR的分析结果显示实验温度下制得的SO42-/TiO2均为锐钛型TiO2;其间掺杂的SO24-在TiO2表面分散性较好,没有聚集成大的颗粒;红外分析的结果初步判定低温（〈550℃）焙烧制得的催化剂SO42-在TiO2表面是螯合双配位吸附,高温焙烧时（〉550℃）SO42-在TiO2表面是桥式配位吸附。     

固定化催化剂TiO2膜光催化降解三氯乙醛的研究

研究了负载于玻璃上的固定化催化剂TiO2膜光催化降解水中三氯乙醛的效果,探讨了TiO2膜光催化降解三氯乙醛的机理,考察了溶液pH值和三氯乙醛初始浓度埘TiO2膜光催化降解三氯乙醛的影响,并研究了固定化催化剂TiO2膜光催化降解三氯乙醛的动力学.结果表明,固定化催化剂TiO2膜光催化降解水中三氯乙醛的效果良好,当三氯乙醛初始浓度为2.25 mg/L时,在紫外光照时间3 h下,三氯乙醛的降解率高达100%.在相司紫外光照时间下,三氯乙醛的光催化降解率随着三氯乙醛初始浓度的增大而下降.在溶液pH=6.5时,三氯乙醛的降解效率最高.固定化催化剂TiO2膜光催化降解三氯乙醛的反应遵循一级反应动力学,反应速率常数随三氯乙醛初始浓度的增大而减小.     

共存物质对钢渣除磷的影响

研究了pH、共存离子（Cl^-、NO3^-、SO4^2-、F^-、HCO3^-）和腐植酸对钢渣吸附除磷的影响。结合吸附饱和钢渣上的磷形态分析了产生影响的原因,采用SEM-EDS（扫描电子显微镜-X射线能谱分析）对吸附磷酸盐前后钢渣表面的微观形态特征进行观察。结果表明：钢渣对磷酸盐具有很好的去除效果,吸附饱和钢渣中的磷主要以Ca—P形式存在。钢渣吸附磷酸盐最适初始pH为3～5,高pH抑制Ca—P的生成,对吸附不利。NHf的存在提高了Ca—P含量,从而促进钢渣对磷酸盐的吸附。共存阴离子Cl^-、NO3^-、SO4^2-对钢渣吸附磷酸盐没有影响,但是F^-和HCO3^-明显抑制Ca—P的生成,从而减少了钢渣对磷酸盐的吸附。腐植酸的存在显著抑制了Ca—P和O-P的生成,使钢渣对磷酸盐的吸附量大大减小。     

参杂负载型纳米TiO2降解橙黄G的光催化活性及其动力学研究

采用溶胶-凝胶法和浸渍-焙烧法制备了掺杂Sn（Ⅳ）的TiO2／AC光催化剂，以偶氮染料橙黄G为目标降解物，对光催化反应条件进行了优化。结果表明：利用Sn（IV）掺杂量为2．5at．％的TiO2／AC光催化剂，在进水浓度50mg／L，催化剂的用量12．5g／i，pH值2．0，H2O2 1．5mL／L。主波长为365nm的300W高压汞灯光照条件下，反应60rain，橙黄G的光催化去除率可达99．1％。该反应符合Langmuir-Hinshelwood动力学方程，其速控步为吸附反应。共存阴离子SO4^2-和H2PO4^-，对橙黄G的光催化降解反应均有一定的抑制作用。     

SO2-4/TiO2光催化降解苯酚

以工业硫酸氧钛为原料水解制得SO42-/TiO2光催化剂,并以苯酚为目标降解物,考察了SO24-/TiO2的光催化性能。结果表明:随着SO42-/TiO2制备过程中焙烧温度的升高,其光催化活性逐渐增加,650℃焙烧获得的SO24-/TiO2的光催化活性最好,此后再升高温度会因催化剂中硫的挥发而下降;在确定苯酚原液初始浓度为50 mg/L条件下,SO42-/TiO2的光催化降解苯酚的最佳工艺条件为反应时间2 h、苯酚pH为7、催化剂用量1 g/L。XRD、SEM和FTIR的分析结果显示实验温度下制得的SO42-/TiO2均为锐钛型TiO2;其间掺杂的SO24-在TiO2表面分散性较好,没有聚集成大的颗粒;红外分析的结果初步判定低温(<550℃)焙烧制得的催化剂SO42-在TiO2表面是螯合双配位吸附,高温焙烧时(>550℃)SO42-在TiO2表面是桥式配位吸附。     

气-固流化床光催化氧化甲苯的研究

在自制的流化床光催化反应装置中研究了中低浓度（28～140 mg/m^3）甲苯的气相光催化降解过程,考察了光照时间、初始浓度、表观气速和催化剂负载量等因素对甲苯光催化降解率的影响规律.结果表明,紫外灯照射约1.5 h,甲苯的转化率达最大值,甲苯初始浓度越低,维持此最大值的时间越久;在一定低浓度范围内（28～55 mg/m^3）,甲苯的转化率不随浓度变化,符合一级反应动力学,浓度进一步增加,则甲苯的转化率下降;表观气速和催化剂负载量的最佳值分别为3.3Umf和0.19 g TiO2/g SiO2.     

电极-SBBR处理含铜有机污水

采用电极一SBBR系统去除Cu^2＋,考察了电流强度,IA竞争离子（阴离子SO4^2-、NO3^-、CL^-和阳离子Zn^2＋、Ph^2＋）、初始含Cu^2＋量及溶液pH值对除铜效除果的影响。结果表明,当电流强度为40mA时Cu^2＋去除率最高为98％。投加阴（SO4^2-、NO3^-、Cl^-）、阳（Zn^2＋、Pb^2＋）离子均会引起出水Cu^2＋浓度的增加,且Cl^-和Ph^2＋含量分别为45mg／L和30mg／L时对Cu^2＋去除的影响更为显著。进水Cu^2＋浓度为30mg／L时,Cu^2＋去除率最高为98．48％,当进水Cu^2＋≥70mg／L时,出水Cu^2＋浓度不能达标。酸性（pH4．0～4．5）与碱性（pH9．0～10．0）条件均不利于Cu^2＋的去除,且酸性条件的负面影响更显著．当pH为4．5～7．5时．Cu^2＋去除率最高为97．78％。     

PVA-I修饰介孔TiO2光催化剂对盐酸四环素的光降解

水热法制备了PVA-I修饰的介孔TiO2催化剂,利用XRD、UV-Vis、BET和Zeta电位等手段对所制备的催化剂进行了表征。研究了改性的介孔TiO2在模拟太阳光下对盐酸四环素的光催化降解,考察了盐酸四环素的初始浓度、溶液的初始pH、共存离子对盐酸四环素光催化降解去除率的影响。实验结果表明,PVA-I修饰的TiO2催化剂为锐钛矿的介孔TiO2,比表面积190.22 m2/g,催化剂的等电点为3.92。PVA-I修饰的介孔TiO2催化剂在模拟太阳光下对TC光催化降解效率可达96.7%,比P25的催化效率提高1.23倍。NO3-、SO2-4和PO3-4对盐酸四环素的光降解有明显的抑制作用。     

固体超强酸SO4^2-／TiO2-SnO2／Ce^4＋光催化降解含酚废水

采用共沉淀-浸渍法制备了固体超强酸SO4^2-／TiO2-SnO2／Ce^4＋,并用XRD、SEM等方法对其结构进行了表征。以苯酚的光催化降解为反应模型,确定了最佳的工艺条件和催化剂再生方法。结果表明：在pH值为6,苯酚初始浓度为50mg／L,催化剂投加量4g／L,光照距离12cm,光照时间为150min,降解率达67．73％,添加助催化剂H2O2后,反应60min,苯酚降解率达到86．33％,催化剂的最佳再生方法是先用1mol／L的硫酸浸渍24h后,在450℃下焙烧6h。     

纳米TiO2/EP光催化降解罗丹明B废水的研究

通过溶胶-凝胶法制备出可漂浮于水面的膨胀珍珠岩(EP)负载型TiO2,研究其在水中对罗丹明B(RB)的去除效果、吸附降解动力学以及最佳工艺条件,并研究其多次回收再生后的降解效果。结果表明,浸渍3次的负载型TiO2光催化活性最高,回收5次后活性变化很小,降解率下降不到8%;光催化剂用量为0.2 g,20 mL初始浓度为10 mg/L和15mg/L RB溶液光照6 h后降解率分别达98%和74%。在实验浓度范围内,该光催化反应可用一级反应动力学方程描述。     

纳米TiO_2/EP光催化降解罗丹明B废水的研究

通过溶胶-凝胶法制备出可漂浮于水面的膨胀珍珠岩（EP）负载型TiO2,研究其在水中对罗丹明B（RB）的去除效果、吸附降解动力学以及最佳工艺条件,并研究其多次回收再生后的降解效果。结果表明,浸渍3次的负载型TiO2光催化活性最高,回收5次后活性变化很小,降解率下降不到8%;光催化剂用量为0.2 g,20 mL初始浓度为10 mg/L和15mg/L RB溶液光照6 h后降解率分别达98%和74%。在实验浓度范围内,该光催化反应可用一级反应动力学方程描述。     

Fe^3＋掺杂TiO2/凹凸棒复合材料的光催化性能

采用酸催化的溶胶-凝胶法制备了一系列Fe^3＋掺杂TiO2/凹凸棒（Fe^3＋-TiO2/ATP）复合光催化剂材料。在可见光条件下,以亚甲基蓝（MB）溶液的光催化降解反应,评价了样品的光催化性能,研究了TiO2负载量、Fe^3＋掺杂量和焙烧温度对复合材料光催化性能的影响。在单因素实验的基础上,采用正交实验设计（L25（53））优化了催化剂的制备条件。光催化实验结果表明,MB在复合材料上的光催化降解反应遵循Langmuir-Hinshelwood（L-H）动力学模型。正交实验结果表明,当TiO2负载量为15%、Fe^3＋掺杂量为0.5%和焙烧温度为550℃时,得到的复合材料对MB的光催化降解效率最佳,测得表观反应速率常数kapp为6.09×10^-3min^-1,反应4 h后MB的降解率（Dt）可达75.88%,相同实验条件下与P25（1.51×10^-3min^-1）相比较,反应速率提高了4.03倍,降解率提高了45.05%。另外,复合材料的沉降性能优于P25,易于分离,是一类有应用前景的复合光催化剂。敏世雄王芳魏立强王永生冯雷佟永纯韩玉琦     

Photolysis of 14C-sulfadiazine in water and manure

Photolysis of 14C-sulfadiazine in aqueous solution under simulated sunlight followed first-order kinetics. The impact of H2O2, humic acid, fulvic acid and acetone to enhance the photodegradation of sulfadiazine (SDZ) was studied. Six photoproducts, 4-OH-SDZ, 5-OH-SDZ, N-formyl-SDZ, 4-[2-iminopyrimidine-1(2H)-yl] aniline, 2-aminopyrimidine, and aniline were identified. Extrusion of SO2 was found to be the main degradation process during irradiation. These photoproducts can occur in water and soil upon sunlight exposure, when soil is treated with SDZ contained in manure. Due to photodegradation the experimental half-life of the SDZ in water was 32h and in the presence of photosensitizers the half-life values were 19.3-31.4h, 17.2-31.4h, 12.6-29.8h, and 3.8-30.7h for H2O2, humic acid, fulvic acid, and acetone, respectively depending on the concentration of the photosensitizers. The presence of photosensitizers markedly reduced SDZ persistence, indicating that indirect photolytic processes are important factors governing the photodegradation of SDZ in aqueous environments. Investigation revealed further persistence behavior of SDZ in manure. The half-life value of SDZ in manure was 158h.     

TiO2膜光催化降解4，4’-二溴联苯的研究

研究了负载于玻璃上的固定化催化剂TiO2膜光催化降解水中4,4’-二溴联苯（4,4’-DBB）的效果,考察了溶液pH值和4,4’-DBB初始浓度等对TiO2膜光催化降解4,4’-DBB的影响,探讨了降解机理。结果表明,TiO2膜光催化降解水中4,4’-DBB的效果良好,紫外光照射8h,初始浓度为4mg／L的4,4’-DBB的降解率高达94％,降解速率随着4,4’-DBB初始浓度的增大而下降。在溶液pH：1时,4,4’-DBB的降解效率最高。超声的加入使降解反应的速率加快。经拟合发现4,4’-DBB的降解符合拟一级反应规律,并推导出动力学方程。     

Titanium dioxide mediated photocatalytic degradation of monochlorobenzene in aqueous phase

The reaction sequence for the photocatalytic degradation of monochlorobenzene (MCB) in UV/TiO2 process, including substrate adsorption, degradation, and mineralization, was studied. The theoretical maximum quantity of MCB that could be adsorbed onto TiO2 surface in aqueous phase was 0.18+/-0.04 micromol m(-2) of TiO2. In accordance with the upper limit of the relative surface coverage of MCB molecules to surface hydroxyls of TiO2 was around 2.2%, the water molecules as the major adjacent species near TiO2 surface would compete with MCB molecules. Increasing the initial substrate concentration to an appropriate value or enhancing the affinity between the MCB and the TiO2 surface by adjusting the solution pH would promote the photocatalytic degradation. Experimental results revealed that the neutral medium was beneficial for the degradation of MCB. In comparison, the mineralization was most improved at acidic condition. Generally, 90% of the total organic carbon (TOC) was mineralized after 240 min illumination time in the examined pH range except solution pH 11. The suppressed mineralization of MCB at solution pH 11 was ascribed to the lack of adsorption. A simplified 2-step consecutive kinetic model was used to simulate the mineralization.     

Study on the photocatalytic reduction of dichromate and photocatalytic oxidation of dichlorvos

In this paper, dichromate and dichlorvos are selected as the deputies of inorganic and organic pollutants, respectively, and TiO2/beads is used as a photocatalyst. The effects of various parameters, such as the amount of the photocatalyst, H2O2 concentration, metal ions, anions, pH value, and organic compounds on the photocatalytic reduction of dichromate and photocatalytic oxidation of dichlorvos are studied. From the studies, the differences of the parameters effect on the photocatalytic degradation of organic and inorganic pollutants are obtained. The results show that the optimum amount of the photocatalyst used is 6.0 g cm(-3) for the photocatalytic reactions. With the addition of a small amount of H2O2, the photocatalytic reduction of dichromate is inhibited while the photocatalytic oxidation of dichlorvos is accelerated. With the addition of trace amounts of Fe3+ or Cu2+, both the reactions are accelerated, and with the addition of Zn2+ and Na+, no obvious effects on the reactions are observed. Acidic solution is favorable for the photocatalytic reduction of dichromate; and acidic and alkaline solutions are favorable for the photocatalytic oxidation of dichlorvos. Adding SO4(2-), the photocatalytic oxidation is accelerated and adding Cl- the reaction is inhibited; and with the addition of trace amounts of SO4(2-), Cl- and NO3-, no obvious effects on the photocatalytic reduction of dichromate are observed. With the addition of methanol and toluene, the photocatalytic reduction of dichromate is accelerated, and the photocatalytic oxidation of dichlorvos is inhibited. The possible roles of the additives on the reactions are also discussed.