管式膜连续微滤装置处理回用城市污水的中试研究

就管式膜连续微滤装置对城市污水处理厂二沉池出水处理回用的可行性进行了中试研究，结果表明。该装置在运行压力为0．12-0．15MPa，反冲洗间隔为18min时，吨水能耗仅为0．45kWh。此时对COD、浊度有较高的去除率。分别为75．71％和94．49％，对氨氮也有一定的去除效果，去除率为40．26％；处理后出水COD、氨氮、浊度均明显优于《生活杂用水水质标准》(CJ25．1-89)中的相关规定。该装置成本低、操作简单，用于污水回用具有较高技术经济可行性。     

一体式膜生物反应器处理生活污水的中试研究

采用中试规模(1.8 m3/d)的缺氧-好氧膜生物反应器(A/O MBR)对城市污水处理回用进行了试验研究.试验结果表明,该工艺处理效果优良,系统对COD、氨氮、浊度、总氮、总磷去除率较高,COD、氨氮出水浓度分别为7～39 mg/L、0～1.31 mg/L.出水水质优于城市杂用水水质标准(GB/T18920-2002).     

一体式膜生物反应器处理生活污水的中试研究

采用中试规模（1.8m^3／d）的缺氧-好氧膜生物反应器（A／OMBR）对城市污水处理回用进行了试验研究。试验结果表明，该工艺处理效果优良，系统对COD、氨氮、浊度、总氮、总磷去除率较高，COD、氨氮出水浓度分别为7～39 mg/L、0～1.31mg／L。出水水质优于城市杂用水水质标准（GB／T18920-2002）。     

新型聚合铝硅混凝剂处理洗浴废水的试验研究

针对常规铝盐、铁盐去除洗浴废水中阴离子洗涤剂 (LAS)效果不理想的状况 ,采用高碱化度钙型聚合铝硅混凝剂 (CPASC)进行了试验研究 ,同时与聚合氯化铝 (PAC)作了比较。结果表明 ,该混凝剂对洗浴废水中COD、LAS、SS及浊度都有较高的去除率 ,特别对LAS、COD的去除率分别比PAC高 10 %和 8%以上。当投加量为 6 0mg/L时 ,出水各项指标均达到生活杂用水水质标准 (GJ2 5 .1 89)。     

电吸附对水中盐类、氨氮、COD的去除效果分析

电吸附技术作为高效、环境友好型的除盐、除氨氮技术,可应用与水的深度处理领域内。为了使污水回用达到工业用水的水质标准,对电吸附去除水中盐类、氨氮、COD的效果进行分析,结果表明,电吸附设备处理不同氨氮浓度的废水,对中低浓度的氨氮去除效果稳定,当进水氨氮浓度低于20 mg/L时,处理后出水氨氮浓度低于5 mg/L,COD浓度小于25 mg/L,达到回用标准;随着进水盐浓度的增大电吸附处理效果逐渐变差,在电导率低于2 500 μS/cm时除盐率在75%左右,氨氮去除率达到70%左右,COD去除率达到60%左右。经电吸附处理后的低氨氮浓度废水,TDS、氨氮浓度均可达到工业回用水标准。     

砂滤/超滤回用处理校园景观水

在连续式65d运行过程中,采用砂滤/超滤回用处理校园景观水,对校园景观水中高锰酸盐指数、氨氮和浊度的去除效果进行了研究。结果表明:(1)生物滤池对高锰酸盐指数去除率为1.5%～37.0%,平均去除率为18.7%;超滤膜对高锰酸盐指数去除率为40.5%～93.7%,平均去除率为67.5%。(2)生物滤池对氨氮去除率为1.0%～77.6%。(3)砂滤/超滤工艺对浊度的去除率为24.6%～100.0%。(4)生物滤池内生物相以菌胶团和后生动物为主,利用后生动物对有机颗粒等的吞噬,使系统具有良好反堵塞自我调节作用。(5)利用10%(质量分数)NaOH对膜清洗效果要优于10%(质量分数)HCl。     

二氧化氯泡沫分离法处理水合肼类废液

采用二氧化氯泡沫分离装置,研究了二氧化氯泡沫分离法对水合肼类废液的处理效果.通过实验重点考察了废水pH值、二氧化氯投加量和反应时间等参数对废水处理效果的影响.在最佳反应条件(即pH值为10,每升废水中二氧化氯的投加量为5 mg/1 000 COD、反应时间为3 h)下进行反应,原废液(COD值为30 000～35 000 mg/L,氨氮总量为2 500～2 700 mg/L)经处理后COD去除率达到99%,氨氮去除率达到96%以上.     

组合填料生物滤池处理锦纶废水二级出水的性能研究

为解决纺织行业水回用问题,采用陶粒和活性炭组合填料生物滤池对锦纶废水二级生物处理出水进行了深度净化,并考察了气水比和水力负荷对曝气生物滤池处理效果的影响.研究结果表明,曝气生物滤池处理效果良好,平均出水COD、NH4 -N和TN分别为32 mg/L、1.5 mg/L和8.1 mg/L.随着气水比的增加,COD和NH4 -N平均去除率相应提高,TN平均去除率先增大后降低,当气水比为2∶1时,COD、NH4 -N和TN平均去除率分别为48.30%、84.24%和42.18%;随着水力负荷的增加,COD、NH4 -N和TN平均去除率均降低,当水力负荷为0.39 m3/m2·h时,COD、NH4 -N和TN平均去除率分别为48.33%、84.81%和42.54%.     

微气泡曝气O3／H2O2处理RO浓水的效能及影响因素

采用O3／H2O2高级氧化工艺处理炼油厂反渗透（RO）浓水,用溶气泵加压溶气并产生微气泡强化传质,确定装置运行条件,考察气体中臭氧浓度、O3／H2O2初始摩尔比、pH和温度对O3／H2O2处理RO浓水效果的影响,并对RO浓水处理效能进行研究。结果表明,随着气体中臭氧浓度的增加,COD的去除率基本呈线性增加;加入适当量H,0,能提高臭氧氧化RO浓水的效果,O3／H2O2初始摩尔比在0～0．8范围内,COD的去除率先增加后下降,O3／H2O2初始摩尔比为O．5时COD去除率最大;pH从6．84增加到9．01,COD去除率逐渐增大,pH为10．03时COD去除率反而降低;在14～28℃范围内,温度低时,升高温度COD去除率增加较大,温度较高时,升高温度对COD去除率的影响较小。为考察该工艺的稳定性,在H：0：／0,初始摩尔比为O．5、溶液pH为8～9、臭氧浓度为80～100mg／L、温度为10-28℃条件下,对COD为90～140mg／L的RO浓水氧化处理4～10h,出水COD维持在39．9～49．9mg／L,达到《城镇污水处理厂污染物排放标准（GB18918—2002）》中的一级A标准;去除1gCOD消耗031．4～3．3g,消耗0,与H,02的总氧量为2．2～4．4g。     

低温环境下内置腐殖土填料SBR系统处理糠醛废水

在水温为5～10℃左右的条件下,通过实验对比了传统SBR系统与内置腐殖土填料式SBR系统处理糠醛废水的效能,结果表明：由于内置腐殖土填料的作用,填料式SBR系统的去除效能要高于未装填料的SBR系统;传统SBR系统的COD、氨氮和总氮的去除率分别为89%、85%和59%,出水浊度为8.6 NTU;填料式SBR系统的COD、氨氮和总氮的去除率分别为95%、90%和71%,出水浊度为1.7 NTU。     

Chloroaromatic pollutants in mussels incubated in two finnish watercourses polluted by industry

Concentrations of different chlorinated compounds were measured in mussels incubated in two polluted watercourses, a river (the River Kymijoki) and a lake (Lake Vanaja) for four weeks in summer 1995. The sum concentrations of polychlorinated phenols (PCP) and biphenyls (PCB) were both about 1 μg/g lipid weight (lw) in Lake Vanaja mussels, while in the River Kymijoki mussels PCPs were non-detectable and PCBs were measured 120 ng/g lIw. The concentrations of toxic polychlorinated dibenzo-p-dioxin (PCDD) and dibenzofuran (PCDF) congeners ranged between <17 and 370 pg/g Iw in Lake Vanaja mussels and between <38 and 11,000 pg/g lw in the River Kymijoki mussels. Polychlorinated diphenyl ethers (PCDE) were detected in the mussels incubated in the River Kymijoki (0.4–1.1 ng/g Iw), but not in those incubated in Lake Vanaja. Polychlorinated phenoxyanisoles (PCPA) were measured 33 ng/g lw and polychlorinated phenoxyphenols (PCPP) 300 ng/g lw in the mussels incubated in the River Kymijoki. PCPAs were also detected in reference samples, which were sediment and pike from the River Kymijoki and Baltic salmon, seal and white-tailed sea eagle.     

Book review

The Pesticide Manual ‐ A World Compendium, 8th Edition, C.R. Worthing, Editor and S.B. Walker, Assistant Editor, British Crop Protection Council, BCPC Publications Sales, Bear Farm, Binfield, Bracknell, Berkshire RG12 5QE, England. 1987, 1100 pp., UK £50; Overseas £56. ISBN 0–948404–01–9.     

Organochlorine compounds in a three-step terrestrial food chain

The concentrations of 15 organochlorine chemicals (PCBs and pesticides) were studied in a Central European oak wood food chain system: Great tit (Parus major), caterpillars (Tortrix viridana, Operophtera brumata, Erannis defoliaria), and oak-leaves (Quercus robur). Juvenile tits receive organochlorines from the mother via egg transfer and, eventually to a greater extent, from the caterpillar food source during nestling period. The concentrations of PCB 153 (2,2′,4,4′,5,5′-hexachlorobiphenyl, the most abundant in this study) was found in leaf material at ca. 1 ng/g, in caterpillars 10 ng/g, and in bird eggs 170 ng/g on an average and on a dry mass basis.     

The chemical stability of formulations of some hydrolyzable insecticides in aqueous mixtures with hydrolysis catalysts

Abstract

The active ingredients in commercial formulations of malathion, oxamyl, carbaryl, diazinon, and chlorpyrifos diluted to “spray tank”; concentrations with buffered distilled or natural water of pH 4–9 were stable for at least 24 hr. Formulations of trichlorfon were not stable at pH 7 or above but disappearance rates were slower than for the pure chemical in homogeneous solution. Cupric ion was observed to be an effective catalyst for the hydrolysis of a variety of pure organophosphorus insecticides but did not catalyze hydrolysis of the active ingredients of the formulations examined. Increasing the dilution of the formulation increased the susceptibility of malathion, oxamyl, and carbaryl to hydrolysis.     

Observations on the influence of water and soil pH on the persistence of insecticides

Abstract

The pH‐disappearance rate profiles were determined at ca. 25°C for 24 insecticides at 4 or 5 pH values over the range 4.5 to 8.0 in sterile phosphate buffers prepared in water‐ethanol (99: 1 v/v). Half‐lives measured at pH 8 were generally smaller than at lower pH values. Changes in half lives between pH 8.0 and 4.5 were largest (>1000x) for the aryl carbamates, carbofuran and carbaryl, the oxime carbamate, oxamyl, and the organophosphorus insecticide, trichlorfon. In contrast, half lives of phorate, terbufos, heptachlor, fensulfothion and aldicarb were affected only slightly by pH changes. Under the experimental conditions described half lives at pH8 varied from 1–2 days for trichlorfon and oxamyl to >1 year for fensulfothion and cyper‐methrin. Insecticide persistence on alumina (acid, neutral and basic), mineral soils amended with aluminum sulfate or calcium hydroxide to different pH values and four natural soils of different pH was examined. No correlation was observed between the measured pH of these solids and the rate of disappearance of selected insecticides applied to them. These observations demonstrate the difficulty of extrapolating the pH dependent disappearance behaviour observed in homogeneous solution to partially solid heterogeneous systems such as soil.     

Evaluation of trichloroethene recovery processes in heterogeneous aquifer cells flushed with biodegradable surfactants

The ability of two biodegradable surfactants, polyoxyethylene (20) sorbitan monooleate (Tween 80) and sodium dihexyl sulfosuccinate (Aerosol MA), to recover a representative dense non-aqueous-phase liquid (DNAPL), trichloroethene (TCE), from heterogeneous porous media was evaluated through a combination of batch and aquifer cell experiments. An aqueous solution containing 3.3% Aerosol MA, 8% 2-propanol and 6 g/l CaCl(2) yielded a weight solubilization ratio (WSR) of 1.21 g TCE/g surfactant, with a corresponding liquid-liquid interfacial tension (IFT) of 0.19 dyn/cm. Flushing of aquifer cells containing a TCE-DNAPL source zone with approximately two pore volumes of the AMA formulation resulted in substantial (>30%) mobilization of TCE-DNAPL. However, a TCE mass recovery of 81% was achieved when the aqueous-phase flow rate was sufficient to displace the mobile TCE-DNAPL toward the effluent well. Aqueous solutions of Tween 80 exhibited a greater capacity to solubilize TCE (WSR=1.74 g TCE/g surfactant) and exerted markedly less reduction in IFT (10.4 dyn/cm). These data contradict an accepted empirical correlation used to estimate IFT values from solubilization capacity, and indicate a unique capacity of T80 to form concentrated TCE emulsions. Flushing of aquifer cells with less than 2.5 pore volumes of a 4% T80 solution achieved TCE mass recoveries ranging from 66 to 85%, with only slight TCE-DNAPL mobilization (<5%) occurring when the total trapping number exceeded 2 x 10(-5). These findings demonstrate the ability of Tween 80 and Aerosol MA solutions to efficiently recover TCE from a heterogeneous DNAPL source zone, and the utility of the total trapping number as a design parameter for a priori prediction of DNAPL mobilization and bank angle formation when flushing with low-IFT solutions. Given their potential to stimulate microbial reductive dechlorination at low concentrations, these surfactants are well-suited for remedial action plans that couple aggressive mass removal followed by enhanced bioremediation to treat chlorinated solvent source zones.     

Radionuclides in pinon pine (Pinus edulis) nuts from los alamos national laboratory lands and the dose from consumption

Abstract

One of the dominant tree species growing within and around the eastern portion of Los Alamos National Laboratory (LANL), Los Alamos, NM, lands is the pinon pine (Pinus edulis). Pinon pine is used for firewood, fence posts, and building materials and is a source of nuts for food—the seeds are consumed by a wide variety of animals and are also gathered by people in the area and eaten raw or roasted. This study investigated the (1) concentration of ³H, ¹³⁷Cs, ⁹⁰Sr, ^totU, ²³⁸Pu, ^{239, 240}Pu, and²⁴¹ Am in soils (0‐ to 12‐in. [31 cm] depth underneath the tree), pinon pine shoots (PPS), and pinon pine nuts (PPN) collected from LANL lands and regional background (BG) locations, (2) committed effective dose equivalent (CEDE) from the ingestion of nuts, and (3) soil to PPS to PPN concentration ratios (CRs). Most radionuclides, with the exception of ³H in soils, were not significantly higher (p < 0.10) in soils, PPS, and PPN collected from LANL as compared to BG locations, and concentrations of most radionuclides in PPN from LANL have decreased over time. The maximum net CEDE (the CEDE plus two sigma minus BG) at the most conservative ingestion rate (10 lb [4.5 kg]) was 0.0018 mrem (0.018 μSv); this is far below the International Commission on Radiological Protection (all pathway) permissible dose limit of 100 mrem (1000 μSv). Soil‐to‐nut CRs for most radionuclides were within the range of default values in the literature for common fruits and vegetables.     

Degradation and sorption of imidacloprid in dissimilar surface and subsurface soils

Degradation and sorption/desorption are important processes affecting the leaching of pesticides through soil. This research characterized the degradation and sorption of imidacloprid (1-[(6-chloro-3-pyridinyl)-methyl]-N-nitro-2-imidazolidinimine) in Drummer (silty clay loam) and Exeter (sandy loam) surface soils and their corresponding subsurface soils using sequential extraction methods over 400 days. By the end of the incubation, approximately 55% of imidacloprid applied at a rate of 1.0 mg kg^?1 degraded in the Exeter sandy loam surface and subsurface soils, compared to 40% of applied imidacloprid within 300 days in Drummer surface and subsurface soils. At the 0.1 mg kg^?1 application rate, dissipation was slower for all four soils. Water-extractable imidacloprid in Exeter surface soil decreased from 98% of applied at day 1 to > 70% of the imidacloprid remaining after 400 d, as compared to 55% in the Drummer surface soil at day 1 and 12% at day 400. These data suggest that imidacloprid was bioavailable to degrading soil microorganisms and sorption/desorption was not the limiting factor for biodegradation. In subsurface soils > 40% of ¹⁴C-benzoic acid was mineralized over 21 days, demonstrating an active microbial community. In contrast, cumulative ¹⁴CO₂ was less than 1.5% of applied ¹⁴C-imidacloprid in all soils over 400 d. Qualitative differences in the microbial communities appear to limit the degradation of imidacloprid in the subsurface soils.     

Biochemical interaction of six op delayed neurotoxicants with several neurotargets

Abstract

Five organophosphorous insecticides: Leptophos, EPN, Cyano‐fenphos, trichloronate and salithion proved to cause irreversible ataxia not only to chicken but also to mice and sheep. TOCP was included as a reference. Cyanofenphos blocked the catecholamine B‐receptor binding activity with ³H‐norepinephrine at a level similar to that of the specific inhibitor propranolol in the mouse heart preparation. In the lamb heart preparation, the B‐receptor was more sensitive to Leptophos, salithion and TOCP than to propranolol. The six compounds and their oxons were screened for their in‐vitro inhibition to monamine oxidase (MAO), acetyl cholinesterase (AChE) and neurotoxic esterase (NTE) in the brain of either mouse, lamb or chicken. It is believed that their AChE inhibition stands for their acute toxicity, while NTE inhibition is responsible for their paralytic ataxia.     

Phytoextraction of lead-contaminated soil using vetivergrass (<Emphasis Type="Italic">Vetiveria zizanioides</Emphasis> L.), cogongrass (<Emphasis Type="Italic">Imperata cylindrica</Emphasis> L.) and carabaograss (<Emphasis Type="Italic">Paspalum conjugatum</Emphasis> L.)

Background, Aims and Scope The global problem concerning contamination of the environment as a consequence of human activities is increasing. Most of the environmental contaminants are chemical by-products and heavy metals such as lead (Pb). Lead released into the environment makes its way into the air, soil and water. Lead contributes to a variety of health effects such as decline in mental, cognitive and physical health of the individual. An alternative way of reducing Pb concentration from the soil is through phytoremediation. Phytoremediation is an alternative method that uses plants to clean up a contaminated area. The objectives of this study were: (1) to determine the survival rate and vegetative characteristics of three grass species such as vetivergrass, cogongrass and carabaograss grown in soils with different Pb levels; and (2) to determine and compare the ability of the three grass species as potential phytoremediators in terms of Pb accumulation by plants. Methods The three test plants: vetivergrass (Vetiveria zizanioides L.); cogongrass (Imperata cylindrica L.); and carabaograss (Paspalum conjugatum L.) were grown in individual plastic bags containing soils with 75 mg kg⁻¹ (37.5 kg ha⁻¹) and 150 mg kg⁻¹ (75 kg ha⁻¹) of Pb, respectively. The Pb contents of the test plants and the soil were analyzed before and after experimental treatments using an atomic absorption spectrophotometer. This study was laid out following a 3 × 2 factorial experiment in a completely randomized design. Results On the vegetative characteristics of the test plants, vetivergrass registered the highest whole plant dry matter weight (33.85–39.39 Mg ha⁻¹). Carabaograss had the lowest herbage mass production of 4.12 Mg ha⁻¹ and 5.72 Mg ha⁻¹ from soils added with 75 and 150 mg Pb kg⁻¹, respectively. Vetivergrass also had the highest percent plant survival which meant it best tolerated the Pb contamination in soils. Vetivergrass registered the highest rate of Pb absorption (10.16 ± 2.81 mg kg⁻¹). This was followed by cogongrass (2.34 ± 0.52 mg kg⁻¹) and carabaograss with a mean Pb level of 0.49 ± 0.56 mg kg⁻¹. Levels of Pb among the three grasses (shoots + roots) did not vary significantly with the amount of Pb added (75 and 150 mg kg⁻¹) to the soil. Discussion Vetivergrass yielded the highest biomass; it also has the greatest amount of Pb absorbed (roots + shoots). This can be attributed to the highly extensive root system of vetivergrass with the presence of an enormous amount of root hairs. Extensive root system denotes more contact to nutrients in soils, therefore more likelihood of nutrient absorption and Pb uptake. The efficiency of plants as phytoremediators could be correlated with the plants’ total biomass. This implies that the higher the biomass, the greater the Pb uptake. Plants characteristically exhibit remarkable capacity to absorb what they need and exclude what they do not need. Some plants utilize exclusion mechanisms, where there is a reduced uptake by the roots or a restricted transport of the metals from root to shoots. Combination of high metal accumulation and high biomass production results in the most metal removal from the soil. Conclusions The present study indicated that vetivergrass possessed many beneficial characteristics to uptake Pb from contaminated soil. It was the most tolerant and could grow in soil contaminated with high Pb concentration. Cogongrass and carabaograss are also potential phytoremediators since they can absorb small amount of Pb in soils, although cogongrass is more tolerant to Pb-contaminated soil compared with carabaograss. The important implication of our findings is that vetivergrass can be used for phytoextraction on sites contaminated with high levels of heavy metals; particularly Pb. Recommendations and Perspectives High levels of Pb in localized areas are still a concern especially in urban areas with high levels of traffic, near Pb smelters, battery plants, or industrial facilities that burn fuel ending up in water and soils. The grasses used in the study, and particularly vetivergrass, can be used to phytoremediate urban soil with various contaminations by planting these grasses in lawns and public parks. ESS-Submission Editor: Dr. Willie Peijnenburg (wjgm.peijnenburg@rivm.nl)