Implementing infrared determination of quartz particulates on novel filters for a prototype dust monitor

Research by the National Institute for Occupational Safety and Health (NIOSH) has pursued quartz analysis for the specialized filter assemblies of a new worker-wearable personal dust monitor (PDM). The PDM is a real-time instrument utilizing a tapered element oscillating microbalance (TEOM). Standard fiberglass TEOM filters cannot accommodate the desired P-7 infrared analytical method used by the Mine Safety and Health Administration (MSHA). Novel filter materials were tested with the objective of demonstrating this type of analysis. Low temperature ashing and spectrometric examination were employed, revealing that nylon fiber candidate filters left minimal residual ash and produced no significant spectral interference. Avoiding titanium dioxide in all filter materials proved to be a key requirement. Fine quartz particulates were collected on prototype filters in a Marple chamber, either open-faced or through PDMs during test runs. The filters were then subjected to MSHA P-7 analysis and the spectrometrically based analytical results for quartz mass were compared to reference measurements. Also, PDM instrumental mass readings were compared to filter gravimetric measurements. Results suggest that the P-7 method is adaptable to variations in filter materials and that quartz dust analysis by the P-7 method when utilizing the new ashable PDM filters can have accuracy and precision within 10% and 4%, respectively. This is within the declared 13% accuracy and 7-10% precision of the P-7 method itself. Instrument mass readings had modest positive bias but met NIOSH accuracy criteria. Continued work with specialized PDM filters is merited, as they are a new type of TEOM sample amenable to ashing analysis of particulates.     

Comparison of PM10 concentrations in high- and medium-volume samplers in a desert environment

The USEPA replaced TSP with PM₁₀ as the National Ambient Air Quality Standard for particulate matter. The commercially available PM₁₀ sampler is a high-volume model using quartz fiber filters. In certain investigations, such as source apportionment studies, chemical analysis of the filter is necessary, however, many analyses cannot be run on quartz filters. An alternate filter such as Teflon is amenable to XRF and ion chemical analyses but is not amenable to analysis for carbon. To overcome these problems DRI constructed a medium-volume PM₁₀ sampler that is capable of collecting particulates on both Teflon and quartz fiber filters simultaneously. This paper describes the design of the DRI medium-volume PM₁₀ sampler, discusses a method for determining equivalence of two samplers, the results of applying the method to test the equivalence of the medium-volume sampler and a commerical high-volume sampler, and examines differences between PM₁₀ and TSP measurements in a southwestern desert.     

西宁冬季PM2.5和PM10手工与自动监测现状研究

为研究PM_(2.5)和PM_(10)手工与自动监测仪器在高海拔地区的适用性,于2014年12月至2015年1月(冬季)在青海省西宁市开展了为期34 d的监测比对实验。PM监测数据表明:手工监测数据之间都有差异,除了受监测滤膜种类的影响,还存在监测仪器间的系统误差。石英滤膜的PM监测数据都高于聚丙烯滤膜,尤其是PM_(2.5)更为明显,偏高近1/4;石英滤膜与聚丙烯滤膜的PM监测数据具有较好的相关性,PM_(10)监测数据的相关系数为0.97。自动监测数据之间进行了同期比对研究,发现TEOM1405DF(微振荡天平法)和APM-2(β射线法)的PM监测值较低,BAM-1020(β射线法)的PM监测值最高;而Grimm(光散射法)的PM监测值居中。BAM1020配备动态加热系统(DHS),其PM监测数据比没有配备DHS的APM-2偏高40%。基于PM监测比对研究,建议在空气污染严重时加密对各监测仪器的运行维护,并加强长期观测以全面评估PM监测。     

Quantitative measurement of streptomycetes using real-time PCR

A quantitative real-time PCR method was developed and used for determination of streptomycetes in indoor dust samples of five homes collected during three years. The specificity of the method was tested with 14 Streptomyces and ten non-streptomycetous species, revealing a high specificity for mesophilic streptomycetes. Thermophilic species and S. albus were not efficiently detected. The method gave reproducible results in replicate analyses of the same dust DNA as well as of duplicate DNA isolations. The amount of streptomycetes in house dust was lowest in winter, followed by summer, and highest in spring and fall. The greatest variation in Streptomyces-concentrations was observed in the spring and fall samples.     

铁和铝离子对土壤水溶性氟化物检测的干扰研究

通过离子选择电极法测定Fe3+和Al3+不同含量的土壤样品中水溶性氟化物试验,研究Fe3+和Al3+对测定的干扰与消除方法,证实了在总离子强度调节缓冲溶液共存下,Fe3+和Al3+对土壤提取液中水溶性氟化物检测结果存在不同程度的负干扰。选择6种代表性土壤样品,在水溶性氟化物提取液中加入20 mg/L的Al3+和100 mg/L的Fe3+做干扰试验,比较了分取不同体积土壤提取液对氟化物检测结果的影响,结果表明,对水溶性ρ(Fe3+)和ρ(Al3+)高的土壤样品,可选择减少提取液取样体积来消除干扰。选取的5种标准样品测试结果与标准值相符,干扰消除方法具有良好的适用性。     

Characterization of fine aerosol and its inorganic components at two rural locations in New York State

Samples of PM(2.5) were collected to measure the concentrations of its chemical constituents at two rural locations, Potsdam and Stockton, NY from November 2002 to August 2005. These samples were collected on multiple filters at both sites, every third day for a 24-h interval with a speciation network sampler. The Teflo(R) filters were analyzed for PM(2.5) mass by gravimetry, and elemental composition by X-ray fluorescence (XRF). Nylasorb(R) filters and Teflo(R) filters were leached with water and analyzed for anions and cations, respectively, by ion chromatography (IC). Fine particulate matter (PM(2.5)) mass and its inorganic component measurements were statistically characterized, and the temporal behavior of these species were assessed. Over the entire study period, PM(2.5) mass concentrations were lower at Potsdam (8.35 mug/m(3)) than at Stockton (10.24 mug/m(3)). At both locations, organic matter (OM) was the highest contributor to mass. Sulfate was the second highest contributor to mass at 27.0% at Potsdam, and 28.7% at Stockton. Nitrate contributions to mass of 8.9 and 9.5% at Potsdam and Stockton, respectively, were the third highest. At both locations, fine PM mass exhibited an annual cycle with a pronounced summer peak and indications of another peak during the winter, consistent with an overall increase in the rate of secondary aerosol formation during the summer, and increased partitioning of ammonium nitrate to the particle phase and condensation of other semi-volatiles during the winter, respectively. An ion-balance analysis indicated that at both locations, during the summers as well as in the winters, the aerosol was acidic. Lognormal frequency distribution fits to the measured mass concentrations on a seasonal basis indicated the overall increase in particle phase secondary aerosol (sulfate and SOA) concentrations during the summers compared to the winters at both locations.     

超声提取-气相色谱质谱法测定大气PM2.5中正构烷烃

建立了超声提取-气相色谱质谱法测定大气PM2.5中32种正构烷烃方法,经离子温度优化、前处理比较、空白滤膜考察等获得了最佳的实验条件。研究发现,高、中、低3种浓度标准曲线的相关系数均在0.995以上,3种浓度的空白样品加标回收率分别为72.2%~117.8%、73.5%~104.4%、73.8%~109.5%,精密度均小于10%,实际样品加标回收率为75.7%~108.9%。当采样体积为24 m3时,各目标化合物的方法检出限为0.046~2.6 ng/m~3;经正构烷烃浓度范围为0.17~64.3 ng/m~3的1月及浓度范围为0.53~7.67 ng/m~3的6月的实际样品验证,该方法的检出限和测量范围也可较好的满足实际样品的测定。     

Recovery of Francisella tularensis from soil samples by filtration and detection by real-time PCR and cELISA

The aim of this study was to develop a specific and highly sensitive method able to detect very low concentrations of Francisella tularensis in soil samples by real-time PCR (qPCR) with SYBR Green I. tul4 gene, which encodes the 17-kDa protein (TUL4) in F. tularensis strains, was amplified using a LightCycler (LC) device. We achieved a detection limit of 0.69 fg of genomic DNA from F. tularensis subp. holarctica live vaccine strain (LVS), corresponding to a value less than 3.4 genome equivalents per reaction. The qPCR was shown to be specific, highly sensitive and reproducible. In addition, we evaluated 2 new methods for recovering bacteria from soil based on 1-step filtration using glass fiber filters and PVDF filters. These filtration methods enabled us to recover F. tularensis efficiently from soil samples. As few as 50 CFU per 0.5 g of soil were detected by qPCR. Capture enzyme-linked immunosorbent assay (cELISA) allowed us to detect and quantify the amount of bacteria recovered from soil by an immunological method. Although qPCR was more sensitive than cELISA, we did not observe substantial differences in the amount of bacteria quantified by both methods.     

Diurnal trends in coarse particulate matter composition in the Los Angeles Basin

To investigate the diurnal profile of the concentration and composition of ambient coarse particles, three sampling sites were set up in the Los Angeles Basin to collect coarse particulate matter (CPM) in four different time periods of the day (morning, midday, afternoon and overnight) in summer and winter. The samples were analyzed for total and water-soluble elements, inorganic ions and water-soluble organic carbon (WSOC). In summer, highest concentrations of CPM gravimetric mass, mineral and road dust, and WSOC were observed in midday and afternoon, when the prevailing onshore wind was stronger. In general, atmospheric dilution was lower in winter, contributing to the accumulation of air pollutants during stagnation conditions. Turbulences induced by traffic become a significant particle re-suspension mechanism, particularly during winter night time, when mixing height was lowest. This is evident by the high levels of CPM mass, mineral and road dust in winter overnight at the near-freeway sites located in urban Los Angeles, and to a lesser extent in Riverside. WSOC levels were higher in summer, with a similar diurnal profile with mineral and road dust, indicating that they either share common sources, or that WSOC may be adsorbed or absorbed onto the surfaces of these dust particles. In general, the contribution of inorganic ions to CPM mass was greater in the overnight sampling period at all sampling sites, suggesting that the prevailing meteorological conditions (lower temperature and higher relative humidity) favor the formation of these ions in the coarse mode. Nitrate, the most abundant CPM-bound inorganic species in this basin, is found to be predominantly formed by reactions with sea salt particles in summer. When the sea salt concentrations were low, the reaction with mineral dust particles and the condensation of ammonium nitrate on CPM surfaces also contributes to the formation of nitrate in the coarse mode.     

Biological responses of workplace particles and their association with adverse health effects on miners

Epidemiological research has demonstrated the relationship between exposure to quartz dust and an elevated risk of pneumoconiosis and possible elevated risk of cancer. The current study was designed to evaluate the biological responses of workplace particles containing crystalline silica using an in vitro cell test. Respirable particle samples were sampled from four tin mines, where the standardized mortality ratio (SMR) for pneumoconiosis was 51.6 and SMR for lung cancer was 2.2 in dust-exposed miners. Alveolar macrophages (AM) are considered as the target cells for primary dust effects. The samples were then measured at 15, 30, 60 and 120 microg particle per 10(6) AM for cytoxicity with the release of glucuronidase, lactate dehydrogenase, for reactive oxygen damage with H(2)O(2) release, and for ability to induce fibrosis using the secretion of tumor necrosis factor-alpha (TNF-alpha). Pure quartz (DQ12) and corundum were used as controls. The results showed the samples from tin mines caused a higher cytoxicity when compared to corundum, yet lower when compared to quartz. However, reactive oxygen species release (148-177 nmol/3 x 10(5) AM in high concentration of 120 microg/10(6) AM) induced by the samples were significantly higher than that induced by quartz (57 nmol/3 x 10(5) AM) and corundum (62 nmol/3 x 10(5) AM). Furthermore, particle samples induced higher TNF-alpha secretion than corundum, the samples from Limu tin mine induced much higher TNF-alpha levels than that induced by DQ12 quartz. The results from the in vitro tests help elucidate the degree of hazard of dust particles in tin mines. The in vitro reaction patterns of AM also constitute a powerful tool to monitor biological and pathogenic responses of humans following dust particle exposure.     

Evaluation of a standardized method for determining soluble silver in workplace air samples

Several occupational exposure limits and guidelines exist for silver, but the values for each depend on the chemical form of the silver compound in question. In the past, it generally was not possible, without prior knowledge of the work process, to distinguish soluble silver from insoluble silver compounds collected in workplace air samples. Therefore, analytical results were historically reported as total silver. In this study, work was conducted to evaluate a method to differentiate between the quantities of water-soluble silver compounds and total silver collected on filters. The investigation entailed an evaluation of an International Organization for Standardization method to determine soluble silver in airborne particulate matter. The study design incorporated laboratory experiments to evaluate analytical figures of merit, such as selection of appropriate filter media and extraction solution, analytical recovery, and sample stability during storage. Polytetrafluoroethylene (PTFE) filters (2 microm, 37 mm) in opaque cassettes were either spiked with known amounts of silver nitrate or contained a known mass of solid silver nitrate. Results showed that over 90% of the silver was recovered from PTFE filters. Also, field studies were conducted in which workplace air samples were collected in two silver refineries. Some of these samples were analyzed only for soluble silver while others were sequentially extracted and analyzed, first, for soluble silver, then for total silver. The mass fractions of soluble silver, as compared to total silver, were approximately 2% or less. This investigation served to validate an international standard procedure for the determination of soluble silver in workplace air samples.     

大气可吸入颗粒物(PM10)中矿物组分的X射线衍射研究

利用X射线衍射技术对北京2002春季和夏季的可吸入颗粒物进行了研究.结果表明,北京春季和夏季可吸入颗粒物的矿物组成明显不同,春季可吸入颗粒物中的矿物以硅铝酸盐为主,同时存在碳酸盐、硫酸盐、硫化物、铁的氧化物、粘土矿物以及难以鉴定的矿物;在夏季的样品中,矿物的种类有所减少,却有新的物种出现,如氯化氨、硫酸氨等.XRD定量分析显示,在沙尘天气时,可吸入颗粒物中石英和粘土矿物以及非晶质分别占到24.1%、28.5%和2 0%,斜长石和方解石分别占到10.4%和8.1%,其他矿物总共不到10%.矿物组分的确定对可吸入颗粒物来源的识别有一定的指导作用.     

Mineralogy of Atmospheric Suspended Dust in Three Indoor And One Outdoor Location in Oman

The aim of this work is to characterize the mineral phases present in the atmosphere at three locations in northern Oman. Samples of atmospheric particles were collected using a high volume sampler. Three indoor and one outdoor location were chosen in this investigation. Sampling locations included a residential house located nearby the cement plant, a residential house located nearby a refinery plant, and a residential house located at Al-Suwayq residential area. Indoor air was sampled from these three houses. Moreover, for the Al-Suwayq residential house, sampling was also taken outside the house for comparison. The dust samples were analysed for their microanalysis characterization and their mineral contents as well. The microanalysis enabled us to identify the metals present in the particles. Furthermore, the mineralogical analysis of the sample filters showed the presence of quartz as the principal phase inside the house of Al-Suwayq, whereas quartz, dolomite, and gypsum were common phases outside the house. In the residential house nearby the cement plant, it was found that calcite, quartz, dolomite and goethite were the principal phases whereas the particles collected from the house nearby the refinery composed primarily of dolomite and calcite. The airborne dust collected at the refinery and Al-Suwayq were probably sourced in the natural environment and mobilised by natural processes. However, at the cement factory the crushing and grinding of limestone during the industrial process has contributed significantly to the airborne dust load. Generally, the information obtained in this study will be invaluable as no data for the mineral content of atmospheric dust existed in the Oman.     

Simultaneous analysis of endosulfan, chlorpyrifos, and their metabolites in natural soil and water samples using gas chromatography-tandem mass spectrometry

Analysis of endosulfan, chlorpyrifos, and their nonpolar metabolites in extracts from environmental aqueous and soil samples was performed using a gas chromatography-tandem mass spectrometry (GC–MS/MS) technique. Full-scan GC–MS analysis showed poor sensitivity for some of the metabolites (endodiol and endosulfan ether). A multisegment MS/MS method was developed and MS/MS parameter isolation time, excitation time, excitation voltage, and maximum excitation energy were optimized for chosen precursor ions to enhance selectivity and sensitivity of the analysis. The use of MS/MS with optimized parameters quantified analytes with significantly higher accuracy, and detection limits were lowered to ~1/6th compared with the full-scan method. Co-eluting compounds, chlorpyrifos and chlorpyrifos oxon, were also analyzed successfully in the MS/MS mode by choosing exclusive precursor ions. Analysis of soil and water phase samples from contaminated soil slurry bioreactors showed that the MS/MS method could provide more reliable estimates of these pesticide and metabolites (especially those present in low concentrations) by annulling interferences from soil organic matter.     

Composition, seasonal variation, and sources of PM10 from world heritage site Taj Mahal, Agra

Air samples for PM(10) (dp?相似文献   

Filtration of fullerene and copper oxide nanoparticles using surface-modified microfilters

This study evaluated the filtration of engineered nanoparticles of fullerene and copper oxide (CuO) from water by using surface-modified microsized filters. The surfaces of microsized filters of cellulose acetate and glass fibers were coated with cationic and anionic surfactants to give them positively and negatively charged surfaces, respectively. Uncoated microfilters removed 30 % of a fullerene suspension, while no nanosized CuO suspension was removed. Cationic surfactant-coated filters enhanced the removal efficiency up to 70 % for the fullerene suspension, while the anionic surfactant-coated filters could not remove fullerene at all. The positively charged filters with cationic surfactant coating could easily adsorb negatively charged fullerenes on their surfaces. However, none of the surfactant-coated filters removed the CuO nanoparticles because the nanoparticles were not affected by the electrical charge of the filtration medium. The Hamaker constants of nanoparticles interacting with the filter materials in water were calculated to study these interactions. The Hamaker constant of fullerene interacting with cellulose acetate in water, 4.68E???21 J, was higher than that of interacting with quartz in water, 2.59E???21 J. However, the Hamaker constants of CuO interacting with quartz and cellulose acetate in water were both negative values, implying repulsive van der Waals interactions. The curves of potential energy of interaction between nanoparticles and the various filter media implied that the nanoparticles were very stable in water, and so, natural deposition of nanoparticles on the filters would not occur. Therefore, electrical bonding and hydrophobic interactions were the forces dominating fullerene removal by positively charged filters.     

波长色散-X射线荧光光谱法测定PM2.5中23种元素

研究以单元素标准膜为基础,结合NIST SRM 2783颗粒物滤膜标准样品,建立了波长色散-X射线荧光光谱法测定PM_2.5中23种无机元素的测定方法,优化了测试条件,测量一个样品耗时约15 min,计算了各元素的方法检出限。对NIST SRM 2783滤膜标准品在一周内重复测定10次来计算方法的准确度与精密度,测定结果显示大多数元素的测量值在给出的参考值范围内,且测量标准偏差一般在10%以内。对比了石英与聚四氟乙烯材质（Teflon）滤膜的空白值,石英滤膜中Si、Fe、Na、Mg、Al、K、Ca等元素的背景值较高,Teflon滤膜的背景值较低,推荐选用Teflon滤膜作为PM_2.5组分分析采样滤膜。分别用波长色散-X射线荧光光谱法及酸消解-ICP-MS法测定了样品膜中的元素组分,得到的测定结果基本一致。     

Concentrations of PM2.5-associated OC, EC, and PCDD/Fs measured during the 2003 wildfire season in Missoula, Montana

Throughout August and September, 2003, wildfires burned in close proximity to Missoula, Montana, with smoke emanating from the fires impacting the valley for much of the summer. This presented the perfect opportunity to measure the levels of polychlorinated dibenzodioxins and dibenzofurans (PCDD/F) comprising ambient forest fire smoke particles impacting the Missoula Valley. An air sampler at the Montana Department of Environmental Quality's (DEQ) compliance site in Missoula measured hourly averages of PM₁₀ throughout the fire season. Three collocated PM_2.5 cyclones collected 24-h smoke samples using quartz filters and Polyurethane Foam (PUF) sorbent cartridges. From the quartz filters, concentrations of Organic and Elemental Carbon (OC/EC) were measured, while PCDD/F were measured from one set of a filter (particle phase) and PUF (vapor phase) aggregate of samples in an attempt to also investigate the different phases of PCDD/F in forest fire smoke impaired communities.Hourly PM₁₀ concentrations peaked at 302.9 μg m⁻³ on August 15. The highest OC concentration (115.6 μg m⁻³) was measured between August 21–22, and the highest EC concentration of 10.5 μg m⁻³ was measured August 20–21. Measurable concentrations of PM_2.5 associated PCDD/Fs were not detected from a representative aggregate sample, with the exception of small amounts of 1,2,3,4,6,7,8-heptachlorodibenzodioxin and octachlorodibenzodioxin. PM_2.5 samples collected during the smoke events were composed of approximately 65% OC. However, the OC fraction of the particles collected in the smoke impaired Missoula valley was not composed of significant amounts of PCDD/F.     

Quantification of PAHs and chlorinated compounds by novel solid-phase microextraction based on the arrays of tin oxide nanorods

The results of an innovative study on a new and highly efficient stationary phase based on the SnO₂ nanorods coating on fused silica have been reported in this paper. SnO₂ nanorods have been grown on fused silica fibers using a hydrothermal process. The extraction properties of the fiber were investigated using headspace solid-phase microextraction (HS-SPME) mode coupled with gas chromatography–mass spectrometry detection for 1,4-dichloro-2-nitrobenzene, biphenyl, and acenaphthene. The effect of different variables on extraction efficiency was studied simultaneously using Box–Behnken method as experimental design. The variables of interest in the HS-SPME were salt effect, adsorption temperature, extraction, and desorption time. Under optimal conditions, the calibration curves were linear up to 10²–10⁵ ng?L^?1 (R ²?>?0.998) with detection limits of 10^?3, 10^?1, and 10 ng?L^?1 for acenaphthene, biphenyl, and 1,4-dichloro-2-nitrobenzene, respectively. The relative standard deviations for single fiber and fiber to fiber were less than 9.8 and 12.5 %, respectively. The high stability of the SnO₂ nanostructure coating is proved at relatively high temperatures (up to 300 °C) with a high extraction capacity and long lifespan (more than 100 times). By applying the proposed technique, promising recoveries (93–98 %) were obtained in the analysis of environmental water samples.     

Evaluation of filter-based aerosol measurements during the 1987 Southern California Air Quality Study

The Southern California Air Quality Study (SCAQS) was conducted during the summer and fall of 1987 to assess the causes of elevated ozone and suspended particulate matter concentrations in California's South Coast Air Basin (SoCAB). Extensive gaseous (i.e. nitric acid, ammonia, sulfur dioxide) and particle (i.e. PM_2.5 and PM₁₀ mass, elements, ions, carbon) measurements were acquired for 11 days during the summer at nine locations, and six days during the fall at six locations. Outliers were identified so that they could be excluded from further statistical analyses. Carbon and elemental measurements were found to be negatively biased by 20% owing to inhomogenous aerosol deposits on the SCAQS filters and analysis methods which were applied to a portion of the filters. These biases seem relatively consistent, however, and should not affect conclusions drawn from data analysis efforts if they are appropriately considered. Significant fractions (30–60%) of ammonium nitrate volatilized during the summer when temperatures were higher. Less than 10% typically volatilized during the fall when temperatures were lower. Anion/cation balances support the accuracy and precision estimates of the nitrate, sulfate, and ammonium measurements. Coarse particle sulfate was generally low, while coarse particle nitrate was most pronounced at the coastal sites.This paper documents SCAQS filter-based aerosol measurement methods, and evaluates the accuracy, precision, and validity of the data set. Various comparisons were made for: (1) PM_2.5/PM₁₀ ratios for mass and major chemical species; (2) sum of chemical species versus measured mass; (3) sulfate versus sulfur ratios; (4) PM_2.5 particulate nitrate versus nitric acid-denuded nitrate; and (5) anion/cation balances. The measurement and evaluation techniques presented in this paper serve as a guideline for other data analysis and modeling studies.