Modelling the spatial distribution of ammonia emissions from seabirds in the UK

Knowledge of the sources and distribution of ammonia (NH3) emissions underpins our understanding of the nitrogen budget. Research has focused on quantifying NH3 emissions from anthropogenic sources, whilst those from natural sources have received little attention internationally. Seabirds excrete large quantities of nitrogen, making seabird colonies a major natural source of NH3. Ammonia emissions from each UK seabird species were estimated and combined with population distribution data to model their spatial distribution. Total NH3 emissions from UK seabirds were estimated at 2.7 kt per year. Seabird emissions are concentrated in remote parts of the UK where anthropogenic emissions are small, so that seabirds often represent the main source of NH3 emissions in these areas. Seabird NH3 emissions were found to have increased by 34% since the 1970s. This corresponds to population changes which may be influenced by human activities, showing that even this natural source can be anthropogenically modified.     

Reducing ammonia emissions and volatile fatty acids in poultry litter with liquid aluminum chloride

This study was a pen trial in which the effects of adding different rates of liquid aluminum chloride (AlCl₃) on litter pH, total volatile fatty acids (VFAs), and ammonia (NH₃) fluxes was evaluated. Liquid AlCl₃ treatments used in this study were sprayed on the rice hull surface at rates of 100 g, 200 g, and 300 g liquid AlCl₃/kg rice hulls; untreated rice hulls served as controls. Litter pH, total VFAs, and NH₃ fluxes were all lowered (P< 0.05) by all of the liquid AlCl₃ treatments compared with controls during certain times of the 5 week study. However, there were no significant differences among treatments on litter pH at the end of the study (from 3 to 5 weeks) or NH₃ fluxes at beginning of the study (0 to 3 weeks). Total VFAs were reduced 16 %, 29 %, and 53 % by 100 g liquid AlCl₃/kg rice hulls, 200 g liquid AlCl₃/kg rice hulls, and 300 g liquid AlCl₃/kg rice hulls, respectively. Liquid AlCl₃additions reduced NH₃ fluxes by 35 %, 57 % and 67 %, respectively, at the low, medium and high rates. In summary, these results indicate that adding liquid aluminum chloride to rice hulls would be a useful tool in reducing the negative environmental impact of poultry litter. It should be noted that the decreased VFA production and NH₃ volatilization was chiefly associated with reduction in litter pH.     

Relationship between ammonia stomatal compensation point and nitrogen metabolism in arable crops: current status of knowledge and potential modelling approaches

The ammonia stomatal compensation point of plants is determined by leaf temperature, ammonium concentration ([NH4+]apo) and pH of the apoplastic solution. The later two depend on the adjacent cells metabolism and on leaf inputs and outputs through the xylem and phloem. Until now only empirical models have been designed to model the ammonia stomatal compensation point, except the model of Riedo et al. (2002. Coupling soil-plant-atmosphere exchange of ammonia with ecosystem functioning in grasslands. Ecological Modelling 158, 83-110), which represents the exchanges between the plant's nitrogen pools. The first step to model the ammonia stomatal compensation point is to adequately model [NH4+]apo. This [NH4+]apo has been studied experimentally, but there are currently no process-based quantitative models describing its relation to plant metabolism and environmental conditions. This study summarizes the processes involved in determining the ammonia stomatal compensation point at the leaf scale and qualitatively evaluates the ability of existing whole plant N and C models to include a model for [NH4+]apo.     

Agricultural ammonia emissions inventory and spatial distribution in the North China Plain

An agricultural ammonia (NH₃) emission inventory in the North China Plain (NCP) on a prefecture level for the year 2004, and a 5 × 5 km² resolution spatial distribution map, has been calculated for the first time. The census database from China's statistics datasets, and emission factors re-calculated by the RAINS model supported total emissions of 3071 kt NH₃-N yr⁻¹ for the NCP, accounting for 27% of the total emissions in China. NH₃ emission from mineral fertilizer application contributed 1620 kt NH₃-N yr⁻¹, 54% of the total emission, while livestock emissions accounted for the remaining 46% of the total emissions, including 7%, 27%, 7% and 5% from cattle, pigs, sheep and goats, and poultry, respectively. A high-resolution spatial NH₃ emissions map was developed based on 1 × 1 km land use database and aggregated to a 5 × 5 km grid resolution. The highest emission density value was 198 kg N ha⁻¹ yr⁻¹.     

Ammonia emissions from livestock industries in Canada: Feasibility of abatement strategies

An updated national ammonia (NH₃) emissions inventory was employed to study the relationship between NH₃ emissions and livestock industries in Canada. Emissions from animal agriculture accounted for 322 kilotonnes (kt) or 64% of Canadian NH₃ emissions in 2002. Cattle and swine accounted for the bulk of livestock emissions. The provinces of Alberta, Ontario, Quebec, and Saskatchewan accounted for 28.1%, 22.0%, 18.7%, and 13.1% of total livestock emissions, respectively. Emissions from Ontario and Quebec were attributed to the intensive production of dairy, hogs and poultry. Dairy cattle emissions per hectolitre of milk were higher in Ontario and Québec than in other provinces, while swine emissions per livestock unit were higher than either beef or dairy cattle. A review of the abatement literature indicated diet manipulation to improve N efficiency and land spreading methods are very effective techniques to lower NH₃ emissions. Future research is required to evaluate the feasibility of biofilters and feces/urine separation methods.     

Modelling the extraction of soil contaminants with supercritical carbon dioxide

Extractions of volatile organic compounds (VOC’s) in contaminated soil from petroleum site were performed with supercritical carbon dioxide at different temperatures, pressures, extraction times, solvent flow rates, soil moisture contents and soil acidity. Three soil systems were investigated in order to compare the best parameters for extraction. A central composite rotatable design has been used to evaluate the influence of operation conditions on the extraction efficiency to generate model equations representing the types of soil. The results indicate that at least 70-80% of the initial amount of VOC’s can be removed at moderate temperatures even at very high moisture content. Supercritical extraction is best suited to silt type soils which have a low adsorption capacity. VOC’s recoveries from the artificial contaminated soil samples were higher in comparison with real contaminated soils. At moderate temperatures, the extraction efficiency for real soils is low because pollutants bind strongly to the soil.     

Modelling the spatial distribution of SO2 and NOx emissions in Ireland

The spatial distributions of sulphur dioxide (SO2) and nitrogen oxides (NOx) emissions are essential inputs to models of atmospheric transport and deposition. Information of this type is required for international negotiations on emission reduction through the critical load approach. High-resolution emission maps for the Republic of Ireland have been created using emission totals and a geographical information system, supported by surrogate statistics and landcover information. Data have been subsequently allocated to the EMEP 50 x 50-km grid, used in long-range transport models for the investigation of transboundary air pollution. Approximately two-thirds of SO2 emissions in Ireland emanate from two grid-squares. Over 50% of total SO2 emissions originate from one grid-square in the west of Ireland, where the largest point sources of SO2 are located. Approximately 15% of the total SO2 emissions originate from the grid-square containing Dublin. SO2 emission densities for the remaining areas are very low, < 1 t km-2 year-1 for most grid-squares. NOx emissions show a very similar distribution pattern. However, NOx emissions are more evenly spread over the country, as about 40% of total NOx emissions originate from road transport.     

新型微生物菌剂对垃圾渗滤液的除臭效果

利用从食材中筛选纯化的特定微生物制成新型复合菌剂,以不同浓度梯度处理垃圾渗滤液,测定其在自然条件下的嗅阈值,监测NH3和H2S即时挥发浓度的变化,评价菌剂的综合除臭效果,设计三因素三水平实验并采用响应面优化法对反应适宜的实验参数进行了优化。研究结果表明,新型复合菌剂的投加会使垃圾渗滤液嗅阈值明显下降;响应面优化模型分析表明,反应时间2.5 d时和0.5%的菌剂投加对抑制NH3的挥发效果最好,而反应时间2.5 d和0.2%的投入量对抑制H2S的挥发效果最好,氧气的供应情况对两者的挥发抑制效果影响不显著。     

Junge relationships in measurement data for cyclic siloxanes in air

In 1974, Junge postulated a relationship between variability of concentrations of gases in air at remote locations and their atmospheric residence time, and this Junge relationship has subsequently been observed empirically for a range of trace gases. Here, we analyze two previously-published datasets of concentrations of cyclic volatile methyl siloxanes (cVMS) in air and find Junge relationships in both. The first dataset is a time series of concentrations of decamethylcyclopentasiloxane (D₅) measured between January and June, 2009 at a rural site in southern Sweden that shows a Junge relationship in the temporal variability of the measurements. The second dataset consists of measurements of hexamethylcyclotrisiloxane (D₃), octamethylcyclotetrasiloxane (D₄) and D₅ made simultaneously at 12 sites in the Global Atmospheric Passive Sampling (GAPS) network that shows a Junge relationship in the spatial variability of the three cVMS congeners. We use the Junge relationship for the GAPS dataset to estimate atmospheric lifetimes of dodecamethylcyclohexasiloxane (D₆), 8:2–fluorotelomer alcohol and trichlorinated biphenyls that are within a factor of 3 of estimates based on degradation rate constants for reaction with hydroxyl radical determined in laboratory studies.     

Modelling photochemical oxidant formation, transport, deposition and exposure of terrestrial ecosystems

The chemical processes responsible for production of photochemical oxidants within the troposphere have been the subject of laboratory and field study throughout the last three decades. During the same period, models to simulate the atmospheric chemistry, transport and deposition of ozone (O(3)) from individual urban sources and from regions have been developed. The models differ greatly in the complexity of chemical schemes, in the underlying meteorology and in spatial and temporal resolution. Input information from land use, spatial and temporally disaggregated emission inventories and meteorology have all improved considerably in recent years and are not fully implemented in current models. The development of control strategies in both North America and Europe to close the gaps between current exceedances of environmental limits, guide values, critical levels or loads and full compliance with these limits provides the focus for policy makers and the support agencies for the research. The models represent the only method of testing a range of control options in advance of implementation. This paper describes currently applied models of photochemical oxidant production and transport at global and regional scales and their ability to simulate individual episodes as well as photochemical oxidant climatology. The success of current models in quantifying the exposure of terrestrial surfaces and the population to potentially damaging O(3) concentrations (and dose) is examined. The analysis shows the degree to which the underlying processes and their application within the models limit the quality of the model products.     

O3、H2O2/O3及UV/O3在焦化废水深度处理中的应用

采用O₃、H₂O₂/O₃和UV/O₃等高级氧化技术(AOPs)对某焦化公司的生化出水进行深度处理,考察了O₃与废水的接触时间、溶液pH、反应温度等因素对废水COD去除率的影响,确定出O₃氧化反应的最佳工艺参数为：接触时间40 min,溶液pH 8.5,反应温度25℃,此条件下废水COD及UV₂₅₄的去除率最高可达47.14%和73.47%;H₂O₂/O₃及UV/O₃两种组合工艺对焦化废水COD及UV₂₅₄的去除率均有一定程度的提高,但H₂O₂/O₃系统的运行效果取决于H₂O₂的投加量。研究结论表明,单纯采用COD作为评价指标,并不能准确反映出O₃系列AOPs对焦化废水中有机污染物的降解作用。     

Sources and processes affecting concentrations of PM10 and PM2.5 particulate matter in Birmingham (U.K.)

Hourly average concentrations of PM₁₀ and PM_2.5 have been measured simultaneously at a site within Birmingham U.K. between October 1994 and October 1995. Comparison of PM₁₀ and NO_x data with two other sites in the same city shows comparable summer and winter mean concentrations and highly significant inter-site correlations for both hourly and daily mean data. Over a four-month period samples were also collected for chemical analysis of sulphate, nitrate, chloride, ammonium and elemental and organic carbon. Analysis of the data indicates a marked difference between summer and winter periods. In the winter months PM_2.5 comprises about 80% of PM₁₀ and is strongly correlated with NO_x indicating the importance of road traffic as a source. In the summer months, coarse particles (PM₁₀−PM_2.5) account for almost 50% of PM₁₀ and the influence of resuspended surface dusts and soils and of secondary particulate matter is evident. The chemical analysis data are also consistent with three sources dominating the PM₁₀ composition: vehicle exhaust emissions, secondary ammonium salts and resuspended surface dusts. Coarse particles from resuspension showed a positive dependence on windspeed, whilst elemental carbon derived from road traffic exhibited a negative dependence.     

电解絮凝法处理老龄垃圾渗滤液的实验研究

为考察简便低耗的电解材料处理效果,采用铸铁阳极电解絮凝法对老龄垃圾渗滤液进行了处理,通过正交实验和单因素实验考察了电解液浓度、电流密度、pH、极板间距对处理效果的影响.结果表明,电解絮凝法对该老龄垃圾渗滤液有较好的处理效果,当电流密度为50 mA/cm2、pH值为9、极板间距为2 cm、电解75 min后,COD和NH...     

Modelling the dissipation kinetics of six commonly used pesticides in two contrasting soils of New Zealand

We used three non-linear bi-phasic models, bi-exponential (BEXP), first-order double exponential decay (FODED), and first-order two-compartment (FOTC), to fit the measured degradation data for six commonly used pesticides (atrazine, terbuthylazine, bromacil, diazinon, hexazinone and procymidone) in two New Zealand soils. Corresponding DT₅₀ and DT₉₀ values for each compound were numerically obtained and compared against those estimated by simple first-order kinetic (SFOK) model. All 3 non-linear models gave good fit of the measured data under both soil depths and were well supported by the values obtained for the respective statistical indices (RMSE, CRM and r ²). The FOTC model gave by far the best fit for most compounds, followed by the FODED and BEXP models. Overall, DT₅₀ values derived by non-linear models for the six compounds in soils from both sites were lower than the values obtained by the SFOK model. Differences in the SFOK and the three non-linear models derived DT₉₀were, however, an order of magnitude higher for some compounds, while for others differences were very small. Although all three non-linear models described most data by giving excellent fits, in a few instances > 5–10% asymptotes hindered the estimation of DT₉₀ values. This work shows that when degradation deviates from first-order kinetic, application of non-linear decay models to describe the kinetics of degradation becomes important in order to derive the true end-points for pesticides in soil.     

Cu/La共掺杂TiO2光催化氧化水中的氨氮

采用水解-沉淀法制备了Cu/La共掺杂纳米TiO2催化剂,利用XRD、XPS和BET技术对其进行表征,并考察了在紫外灯下,共掺杂TiO2对氨氮的光催化氧化工艺条件。物相结构和比表面积测试结果表明,共掺杂催化剂具有较好的锐钛矿晶型,孔径分布为4～8 nm,Cu/La共掺杂TiO2La以La3+,Cu是以Cu2+、Cu+的形式掺杂进入TiO2的晶格。光催化实验表明:所得改性光催化剂对氨氮的去除及焦化废水的处理均具有较高的催化活性。     

Ammonia in the environment: from ancient times to the present

Recent research on atmospheric ammonia has made good progress in quantifying sources/sinks and environmental impacts. This paper reviews the achievements and places them in their historical context. It considers the role of ammonia in the development of agricultural science and air chemistry, showing how these arose out of foundations in 18th century chemistry and medieval alchemy, and then identifies the original environmental sources from which the ancients obtained ammonia. Ammonia is revealed as a compound of key human interest through the centuries, with a central role played by sal ammoniac in alchemy and the emergence of modern science. The review highlights how recent environmental research has emphasized volatilization sources of ammonia. Conversely, the historical records emphasize the role of high-temperature sources, including dung burning, coal burning, naturally burning coal seams and volcanoes. Present estimates of ammonia emissions from these sources are based on few measurements, which should be a future priority.     

掺Al-TiO2改性膨润土去除微污染水中COD和NH4-N

采用掺Al-TiO2作为改性剂制备改性膨润土,考察了微波辐射功率、辐射时间、TiO2改性剂用量、铝盐掺杂量、pH值对微污染水中COD和NH4-N去除效果的影响。实验表明,微波辐射功率为460 W,辐射时间为8 min,TiO2改性剂用量为1.3 mmol/g,铝盐掺杂量为0.2 mmol/g为最佳制备条件。pH值为6.0,改性膨润土投加量为40 mg/L,沉淀时间为30min时,对微污染水中初始浓度15 mg/L的COD和5 mg/L的NH4-N去除率分别达到92%和59%以上。     

Photocatalytic degradation of the herbicide pendimethalin using nanoparticles of BaTiO3/TiO2 prepared by gel to crystalline conversion method: A kinetic approach

Photocatalytic degradation of the herbicide, pendimethalin (PM) was investigated with BaTiO₃/TiO₂ UV light system in the presence of peroxide and persulphate species in aqueous medium. The nanoparticles of BaTiO₃ and TiO₂ were obtained by gel to crystallite conversion method. These photo catalysts are characterized by energy dispersive x-ray analysis (EDX), scanning electron microscope (SEM), x-ray diffraction (XRD), and Brunauer-Emmett-Teller (BET) adsorption isotherm and reflectance spectral studies. The quantum yields for TiO₂ and BaTiO₃ for the degradation reactions are 3.166 Einstein m^?2 s^?1 and 2.729 Einstein m^?2 s^?1 and catalytic efficiencies are 6.0444 × 10^?7 mg^?2h^?1L² and 5.403 × 10^?7 mg^?2h^?1L², respectively as calculated from experimental results. BaTiO₃ exhibited comparable photocatalytic efficiency in the degradation of pendimethalin as the most widely used TiO₂ photocatalyst. The persulphate played an important role in enhancing the rate of degradation of pendimethalin when compared to hydrogen peroxide. The degradation process of pendimethalin followed the first-order kinetics and it is in agreement with Langmuir-Hinshelwood model of surface mechanism. The reason for high stability of pendimethalin for UV-degradation even in the presence of catalyst and oxidizing agents were explored. The higher rate of degradation was observed in alkaline medium at pH 11. The degradation process was monitored by spectroscopic techniques such as ultra violet-visible (UV-Vis), infrared (IR) and gas chromatography mass spectroscopy (GC-MS). The major intermediate products identified were: N-propyl-2-nitro-6-amino-3, 4-xylidine, (2, 3-dimethyl-5-nitro-6-hydroxy amine) phenol and N-Propyl-3, 4-dimethyl-2, 6-dinitroaniline by GC-MS analysis and the probable reaction mechanism has been proposed based on these products.     

Traffic generated non-exhaust particulate emissions from concrete pavement: A mass and particle size study for two-wheelers and small cars

This study aimed to understand the non-exhaust (NE) emission of particles from wear of summer tire and concrete pavement, especially for two wheelers and small cars. A fully enclosed laboratory-scale model was fabricated to simulate road tire interaction with a facility to collect particles in different sizes. A road was cast using the M-45 concrete mixture and the centrifugal casting method. It was observed that emission of large particle non exhaust emission (LPNE) as well as PM₁₀ and PM_2.5 increased with increasing load. The LPNE was 3.5 mg tire⁻¹ km⁻¹ for a two wheeler and 6.4 mg tire⁻¹ km⁻¹ for a small car. The LPNE can lead to water pollution through water run-off from the roads. The contribution of the PM₁₀ and PM_2.5 was smaller compared to the LPNE particles (less than 0.1%). About 32 percent of particle mass of PM₁₀ was present below 1 μm. The number as well as mass size distribution for PM₁₀ was observed to be bi-modal with peaks at 0.3 μm and 4–5 μm. The NE emissions did not show any significant trend with change in tire pressure.     

Photolysis of the herbicide bispyribac sodium in aqueous medium under the influence of UV and sunlight in presence or absence of sensitizers

The photolysis of a rice herbicide Bispyribac sodium (Sodium 2, 6-bis [(4, 6-dimethoxypyrimidin-2-yl) oxy] benzoate) has been studied in different aqueous medium (distilled water, pond water and Irrigation water) under the influence of UV (λ max ≥ 250 nm) and sunlight in presence or absence of sensitizers (TiO₂ and KNO₃). The study was conducted under laboratory simulated condition which made it possible to evaluate the contribution of different factors viz. source of irradiation, solvent and sensitizers towards the photolysis of bispyribac sodium. The photodegradation proceeds via first order reaction Kinetics in all the cases. Five photo metabolites (M₁-M₅) were isolated in pure form by column chromatographic method from the irradiation system under UV influenced and TiO₂ as sensitizer. From the different spectral data (IR, NMR, UV-VIS, Mass) the structure of these five metabolites were assigned as M₁ (Phenol), M₂ [2, 6-Dihydroxy benzoic acid], M₃ [2, 6-bis [(4, 6 dimethoxypyrimidin-2yl) oxy] benzoic acid], M₄ [2-(3-Hydroxy-phenoxy)-pyrimidine-4, 6-diol] and M₅ as [2,4-Dihydroxy-3, 5-dimethoxy-6-(4-methoxy pyrimidine-2-yloxy)-benzoic acid]. Moreover, another six photometabolites (M₆-M₁₁) were identified from the different irradiation system on the basis of Micromass analysis. On the basis of MS/MS data analysis, the structure of these six photometabolites were assigned as M₆ [2-(4, 6-Dimethoxy-pyrimidin-2-yloxy)-6-hydroxy-benzoic acid], M₇ [2-Hydroxy-6-(4-hydroxy-6-methoxy-pyrimidin-2-yloxy)-benzoic acid], M₈ [4, 6-Dimethoxy-pyrimidin-2-ol], M₉ [6-Methoxy-pyrimidine-2, 4-diol], M₁₀ [2-Hydroxy-6-(pyrimidin-2-yloxy)-benzoic acid] and M₁₁ [2, 4, 6-Trimethoxy-pyrimidine]. The plausible Photodegradation pathways of bispyribac sodium in the present investigation were portrayed which proceeds via hydrolysis, hydrolytic cleavage, O-dealkylation, decarboxylation, dehydroxylation, O-alkylation and hydroxylation.