Long-term coal gasification-based power plants with near-zero emissions. Part A: Zecomix cycle

These two part papers analyse three plant configurations for high efficiency, near-zero emissions power generation from coal, suitable for long-term installations. In the first part the Zecomix cycle, a novel power plant based on various innovative processes, is presented. Zecomix plant is based on a coal hydrogasification process, using recycled steam and hydrogen as gasifying agents, to produce a CH₄ rich syngas. Methane is then converted to an H₂/H₂O based syngas and CO₂ is captured, by reacting in two carbonator reactors with CaO-based solid sorbent. CaCO₃ produced in carbonators is thermally regenerated in a calciner. The synthetic fuel is burned with oxygen in a semi-closed high temperature steam cycle, with a supercritical heat recovery.The paper presents a detailed analysis of the thermodynamic aspects of the process, with the scope of assessing its potential performance in terms of efficiency and emissions. Main operating parameters of the chemical island (e.g. hydrogasifier and calciner pressure, steam flow rates to carbonators, syngas recycle fraction) and of the power island (e.g. pressure ratio, turbine inlet temperature and reheat pressure) were varied in order to evaluate their effect on plant performance and to optimize the process. Critical issues are specifically discussed: the calcination process, the calcium oxide utilization in carbonators, the cooling requirement of the high temperature turbine, the presence of incondensable species in the steam cycle. An accurate performance estimation is therefore developed by considering advanced components, as an evolution of today's technology, excluding unproven devices whose feasibility cannot be anticipated.Depending on sorbent utilization, a net plant efficiency of 44–47% with a virtually complete carbon capture was obtained, a very interesting result with respect to other proposed coal-fired power plants with carbon capture. The high complexity of the chemical island and the importance of a good sorbent performance should be however taken into account for a fair comparison with other plant concepts. Further experimental investigations are mandatory to demonstrate the technical and economical feasibility of the Zecomix plant.     

Capture-ready coal plants—Options,technologies and economics

This paper summarizes the spectrum of options that can be employed during the initial design and construction of pulverized coal (PC), and integrated gasification and combined cycle (IGCC) plants to reduce the capital costs and energy losses associated with retrofitting for CO₂ capture at some later time in the future. It also estimates lifetime (40 year) net present value (NPV) costs of plants with differing levels of pre-investment for CO₂ capture under a wide range of CO₂ price scenarios. Three scenarios are evaluated—a baseline supercritical PC plant, a baseline IGCC plant and an IGCC plant with pre-investment for capture. This analysis evaluates each technology option under a range of CO₂ price scenarios and determines the optimum year of retrofit, if any. The results of the analysis show that a baseline PC plant is the most economical choice under low CO₂ prices, and IGCC plants are preferable at higher CO₂ prices (e.g., an initial price of about $22/t CO₂ starting in 2015 and growing at 2%/year). Little difference is seen in the lifetime NPV costs between the IGCC plants with and without pre-investment for CO₂ capture. This paper also examines the impact of technology choice on lifetime CO₂ emissions. The difference in lifetime emissions become significant only under mid-estimate CO₂ price scenarios (roughly between $20 and 40/t CO₂) where IGCC plants will retrofit sooner than a PC plant.     

Use of experience curves to estimate the future cost of power plants with CO2 capture

Given the dominance of power plant emissions of greenhouse gases, and the growing worldwide interest in CO₂ capture and storage (CCS) as a potential climate change mitigation option, the expected future cost of power plants with CO₂ capture is of significant interest. Reductions in the cost of technologies as a result of learning-by-doing, R&D investments and other factors have been observed over many decades. This study uses historical experience curves as the basis for estimating future cost trends for four types of electric power plants equipped with CO₂ capture systems: pulverized coal (PC) and natural gas combined cycle (NGCC) plants with post-combustion CO₂ capture; coal-based integrated gasification combined cycle (IGCC) plants with pre-combustion capture; and coal-fired oxyfuel combustion for new PC plants. We first assess the rates of cost reductions achieved by other energy and environmental process technologies in the past. Then, by analogy with leading capture plant designs, we estimate future cost reductions that might be achieved by power plants employing CO₂ capture. Effects of uncertainties in key parameters on projected cost reductions also are evaluated via sensitivity analysis.     

Exergy analysis as a tool for the integration of very complex energy systems: The case of carbonation/calcination CO2 systems in existing coal power plants

A common characteristic of carbon capture and storage systems is the important energy consumption associated with the CO₂ capture process. This important drawback can be solved with the analysis, synthesis and optimization of this type of energy systems. The second law of thermodynamics has proved to be an essential tool in power and chemical plant optimization. The exergy analysis method has demonstrated good results in the synthesis of complex systems and efficiency improvements in energy applications.In this paper, a synthesis of pinch analysis and second law analysis is used to show the optimum window design of the integration of a calcium looping cycle into an existing coal power plant for CO₂ capture. Results demonstrate that exergy analysis is an essential aid to reduce energy penalties in CO₂ capture energy systems. In particular, for the case of carbonation/calcination CO₂ systems integrated in existing coal power plants, almost 40% of the additional exergy consumption is available in the form of heat. Accordingly, the efficiency of the capture cycle depends strongly on the possibility of using this heat to produce extra steam (live, reheat and medium pressure) to generate extra power at steam turbine. The synthesis of pinch and second law analysis could reduce the additional coal consumption due to CO₂ capture 2.5 times, from 217 to 85 MW.     

A qualitative reliability and operability analysis of an integrated reforming combined cycle plant with CO2 capture

Most of the current CO₂ capture technologies are associated with large energy penalties that reduce their economic viability. Efficiency has therefore become the most important issue when designing and selecting power plants with CO₂ capture. Other aspects, like reliability and operability, have been given less importance, if any at all, in the literature.This article deals with qualitative reliability and operability analyses of an integrated reforming combined cycle concept. The plant reforms natural gas into a syngas, the carbon is separated out as CO₂ after a water-gas shift section, and the hydrogen-rich fuel is used for a gas turbine. The qualitative reliability analysis in the article consists of a functional analysis followed by a failure mode, effects, and criticality analysis (FMECA). The operability analysis introduces the comparative complexity indicator (CCI) concept.Functional analysis and FMECA are important steps in a system reliability analysis, as they can serve as a platform and basis for further analysis. Also, the results from the FMECA can be interesting for determining how the failures propagate through the system and their effects on the operation of the process. The CCI is a helpful tool in choosing the level of integration and to investigate whether or not to include a certain process feature. Incorporating the analytical approach presented in the article during the design stage of a plant can be advantageous for the overall plant performance.     

Life cycle assessment of carbon dioxide capture and storage from lignite power plants

In this article, we present a life cycle assessment (LCA) of CO₂ capture and storage (CCS) for several lignite power plant technologies. The LCA includes post-combustion, pre-combustion and oxyfuel capture processes as well as subsequent pipeline transport and storage of the separated CO₂ in a depleted gas field.The results show an increase in cumulative energy demand and a substantial decrease in greenhouse gas (GHG) emissions for all CO₂ capture approaches in comparison with power plants without CCS, assuming negligible leakage within the time horizon under consideration. Leakage will, however, not be zero. Due to the energy penalty, CCS leads to additional production of CO₂. However, the CO₂ emissions occur at a much lower rate and are significantly delayed, thus leading to different, and most likely smaller, impacts compared to the no-sequestration case. In addition, a certain share of the CO₂ will be captured permanently due to chemical reactions and physical trapping.For other environmental impact categories, the results depend strongly on the chosen technology and the details of the process. The post-combustion approach, which is closest to commercial application, leads to sharp increases in many categories of impacts, with the impacts in only one category, acidification, reduced. In comparison with a conventional power plant, the pre-combustion approach results in decreased impact in all categories. This is mainly due to the different power generation process (IGCC) which is coupled with the pre-combustion technology.In the case of the oxyfuel approach, the outcome of the LCA depends highly on two uncertain parameters: the energy demand for air separation and the feasibility of co-capture of pollutants other than CO₂. If co-capture were possible, oxyfuel could lead to a near-zero emission power plant.     

Effective retrofitting of post-combustion CO2 capture to coal-fired power plants and insensitivity of CO2 abatement costs to base plant efficiency

Existing coal-fired power plants were not designed to be retrofitted with carbon dioxide post-combustion capture (PCC) and have tended to be disregarded as suitable candidates for carbon capture and storage on the grounds that such a retrofit would be uneconomical. Low plant efficiency and poor performance with capture compared to new-build projects are often cited as critical barriers to capture retrofit. Steam turbine retrofit solutions are presented that can achieve effective thermodynamic integration between a post-combustion CO₂ capture plant and associated CO₂ compressors and the steam cycle of an existing retrofitted unit for a wide range of initial steam turbine designs. The relative merits of these capture retrofit integration options with respect to flexibility of the capture system and solvent upgradability will be discussed. Provided that effective capture system integration can be achieved, it can be shown that the abatement costs (or cost per tonne of CO₂ to justify capture) for retrofitting existing units is independent of the initial plant efficiency. This then means that a greater number of existing power plants are potentially suitable for successful retrofits of post-combustion capture to reduce power sector emissions. Such a wider choice of retrofit sites would also give greater scope to exploit favourable site-specific conditions for CCS, such as ready access to geological storage.     

Steam demand reduction of water–gas shift reaction in IGCC power plants with pre-combustion CO2 capture

This paper presents the results of system assessments that were conducted to compare conventional and advanced water–gas shift reactor sections. The latter are specifically tailored for Integrated Gasification Combined Cycles (IGCC) power plants with pre-combustion CO₂ capture. The advanced shift reactor section comprises four staged reactors with distributed feeds of synthesis gas and quench water in between the reactors. Conventional shift reactor sections consist of two sequential reactors with intermediate cooling, where the entire synthesis gas stream passes both reactors.The advanced shift reactor section reduces the steam requirement of the water–gas shift reaction up to 70% in comparison with conventional configurations, at carbon dioxide capture ratios of approximately 85%. This reduction allows for lower electric efficiency penalties, thus higher net electric outputs for IGCC power plants with CO₂ capture. For each case, the CO₂ capture ratio was optimised for the lowest specific lost work per amount of captured CO₂. Both the number of reactors and the total catalyst volume are higher for the advanced shift reactor sections, resulting in increased capital expenses. In case of four staged reactors, the additional expenses are expected to be outperformed by the increased revenues associated with the higher net electric output.     

CO2 capture from coal-fired power plants based on sodium carbonate slurry; a systems feasibility and sensitivity study

In this work the feasibility of a CO₂ capture system based on sodium carbonate–bicarbonate slurry and its integration with a power plant is studied. The results are compared to monoethanolamine (MEA)-based capture systems. Condensing power plant and combined heat and power plant with CO₂ capture is modelled to study the feasibility of combined heat and power plant for CO₂ capture.Environmental friendly sodium carbonate would be an interesting chemical for CO₂ capture. Sodium carbonate absorbs CO₂ forming sodium bicarbonate. The low solubility of sodium bicarbonate is a weak point for the sodium carbonate based liquid systems since it limits the total concentration of carbonate. In this study the formation of solid bicarbonate is allowed, thus forming slurry, which can increase the capacity of the solvent. With this the energy requirement of stripping of the solvent could potentially be around 3.22 MJ/kg of captured CO₂ which is significantly lower than with MEA based systems which typically have energy consumption around 3.8 MJ/kg of captured CO₂.Combined heat and power plants seem to be attractive for CO₂ capture because of the high total energy efficiency of the plants. In a condensing power plant the CO₂ capture decreases directly the electricity production whereas in a combined heat and power plant the loss can be divided between district heat and electricity according to demand.     

Benchmarking of power cycles with CO2 capture—The impact of the selected framework

The paper puts focus on the selection of an appropriate framework for benchmarking studies of power cycles with CO₂ capture. The need for a reference power plant without CO₂ capture in a benchmarking study is emphasized. The impact of the use of site-specific plant boundary conditions is discussed as well as the selection of computational assumptions to reflect future technology development. A significant part of the paper is dedicated to a study of how changes in the benchmarking framework to reflect technology development can give additional knowledge about the potential for different CO₂ capture technologies. A major conclusion, based on the findings, is that it should be highly relevant for technology providers to investigate the future development potential for a CO₂ capture technology before launching a product development program.     

Design and off-design analyses of a pre-combustion CO2 capture process in a natural gas combined cycle power plant

In this study, a cycle designed for capturing the greenhouse gas CO₂ in a natural gas combined cycle power plant has been analyzed. The process is a pre-combustion CO₂ capture cycle utilizing reforming of natural gas and removal of the carbon in the fuel prior to combustion in the gas turbine. The power cycle consists of a H₂-fired gas turbine and a triple pressure steam cycle. Nitrogen is used as fuel diluent and steam is injected into the flame for additional NO_x control. The heat recovery steam generator includes pre-heating for the various process streams. The pre-combustion cycle consists of an air-blown auto-thermal reformer, water–gas shift reactors, an amine absorption system to separate out the CO₂, as well as a CO₂ compression block. Included in the thermodynamic analysis are design calculations, as well as steady-state off-design calculations. Even though the aim is to operate a plant, as the one in this study, at full load there is also a need to be able to operate at part load, meaning off-design analysis is important. A reference case which excludes the pre-combustion cycle and only consists of the power cycle without CO₂ capture was analyzed at both design and off-design conditions for comparison. A high degree of process integration is present in the cycle studied. This can be advantageous from an efficiency stand-point but the complexity of the plant increases. The part load calculations is one way of investigating how flexible the plant is to off-design conditions. In the analysis performed, part load behavior is rather good with efficiency reductions from base load operation comparable to the reference combined cycle plant.     

Multi-stage chemical looping combustion (CLC) for combined cycles with CO2 capture

This paper presents application of the chemical looping combustion (CLC) method in natural gas-fired combined cycles for power generation with CO₂ capture. A CLC combined cycle consisting of single CLC-reactor system, an air turbine, a CO₂-turbine and a steam cycle has been designated as the base-case cycle. The base-case cycle can achieve net plant efficiency of about 52% at an oxidation temperature of 1200 °C. In order to achieve a reasonable efficiency at lower oxidation temperatures, reheat is introduced into the air turbine by employing multi CLC-reactors. The results show that the single reheat CLC-combined cycle can achieve net plant efficiency of above 51% at oxidation temperature of 1000 °C and above 53% at the oxidation temperature of 1200 °C including CO₂ compression to 110 bar. The double reheat cycle results in marginal efficiency improvement as compared to the single reheat cycle. The CLC-cycles are also compared with a conventional combined cycle with and without post-combustion capture in amine solution. All the CLC-cycles show higher net plant efficiencies with close to 100% CO₂ capture as compared to a conventional combined cycle with post-combustion capture, which is very promising.     

Integration of post-combustion capture and storage into a pulverized coal-fired power plant

Post-combustion CO₂ capture and storage (CCS) presents a promising strategy to capture, compress, transport and store CO₂ from a high volume–low pressure flue gas stream emitted from a fossil fuel-fired power plant. This work undertakes the simulation of CO₂ capture and compression integration into an 800 MW_e supercritical coal-fired power plant using chemical process simulators. The focus is not only on the simulation of full load of flue gas stream into the CO₂ capture and compression, but also, on the impact of a partial load. The result reveals that the energy penalty of a low capture efficiency, for example, at 50% capture efficiency with 10% flue gas load is higher than for 90% flue gas load at the equivalent capture efficiency by about 440 kWh_e/tonne CO₂. The study also addresses the effect of CO₂ capture performance by different coal ranks. It is found that lignite pulverized coal (PC)-fired power plant has a higher energy requirement than subbituminous and bituminous PC-fired power plants by 40.1 and 98.6 MW_e, respectively. In addition to the investigation of energy requirement, other significant parameters including energy penalty, plant efficiency, amine flow rate and extracted steam flow rate, are also presented. The study reveals that operating at partial load, for example at half load with 90% CO₂ capture efficiency, as compared with full load, reduces the energy penalty, plant efficiency drop, amine flow rate and extracted steam flow rate by 9.9%, 24.4%, 50.0% and 49.9%, respectively. In addition, the effect of steam extracted from different locations from a series of steam turbine with the objective to achieve the lowest possible energy penalty is evaluated. The simulation shows that a low extracted steam pressure from a series of steam turbines, for example at 300 kPa, minimizes the energy penalty by up to 25.3%.     

Integration of CO2 capture unit using single- and blended-amines into supercritical coal-fired power plants: Implications for emission and energy management

This work provides the essential information and approaches for integration of carbon dioxide (CO₂) capture units into power plants, particularly the supercritical type, so that energy utilization and CO₂ emissions can be well managed in the subject power plants. An in-house model, developed at the University of Regina, Canada, was successfully used for simulating a 500 MW supercritical coal-fired power plant with a post-combustion CO₂ capture unit. The simulations enabled sensitivity and parametric study of the net efficiency of the power plant, the coal consumption rate, and the amounts of CO₂ captured and avoided. The parameters of interest include CO₂ capture efficiency, type of coal, flue gas delivery scheme, type of amine used in the capture unit, and steam pressure supplied to the capture unit for solvent regeneration. The results show that the advancement of MEA-based CO₂ capture units through uses of blended monoethanolamine–methyldiethanolamine (MEA–MDEA) and split flow configuration can potentially make the integration of power plant and CO₂ capture unit less energy intensive. Despite the increase in energy penalty, it may be worth capturing CO₂ at a higher efficiency to achieve greater CO₂ emissions avoided. The flue gas delivery scheme and the steam pressure drawn from the power plant to the CO₂ capture unit should be considered for process integration.     

CO2 capture from combined cycles integrated with Molten Carbonate Fuel Cells

In this paper Molten Carbonate Fuel Cells (MCFCs) are considered for their potential application in carbon dioxide separation when integrated into natural gas fired combined cycles. The MCFC performs on the anode side an electrochemical oxidation of natural gas by means of CO₃^2? ions which, as far as carbon capture is concerned, results in a twofold advantage: the cell removes CO₂ fed at the cathode to promote carbonate ion transport across the electrolyte and any dilution of the oxidized products is avoided.The MCFC can be “retrofitted” into a combined cycle, giving the opportunity to remove most of the CO₂ contained in the gas turbine exhaust gases before they enter the heat recovery steam generator (HRSG), and allowing to exploit the heat recovery steam cycle in an efficient “hybrid” fuel cell + steam turbine configuration. The carbon dioxide can be easily recovered from the cell anode exhaust after combustion with pure oxygen (supplied by an air separation unit) of the residual fuel, cooling of the combustion products in the HRSG and water separation. The resulting power cycle has the potential to keep the overall cycle electrical efficiency approximately unchanged with respect to the original combined cycle, while separating 80% of the CO₂ otherwise vented and limiting the size of the fuel cell, which contributes to about 17% of the total power output so that most of the power capacity relies on conventional low cost turbo-machinery. The calculated specific energy for CO₂ avoided is about 4 times lower than average values for conventional post-combustion capture technology. A sensitivity analysis shows that positive results hold also changing significantly a number of MCFC and plant design parameters.     

Designing a supercritical steam cycle to integrate the energy requirements of CO2 amine scrubbing

Absorption by chemical solvents combined with CO₂ long-term storage appears to offer interesting and commercial applicable CO₂ capture technology. However one of the main disadvantages is related to the large quantities of heat required to regenerate the amine solvent that means an important power plant efficiency penalty. Different studies have analyzed alternatives to reduce the heat duty on the reboiler and the thermal integration requirements on existing power cycles. In these studies integration principles have been well set up, but there is a lack of information about how to achieve an integrated design and the thermal balances of the modified cycle flowsheet. This paper proposes and provides details about a set of modifications of a supercritical steam cycle to overcome the energy requirements through energetic integration with the aim of reducing the efficiency and power output penalty associated with CO₂ capture process. Modifications include a new designed low-pressure heater flowsheet to take advantage of the CO₂ compression cooling for postcombustion systems and integration of amine reboiler into a steam cycle. It has been carried out several simulations in order to obtain power plant performance depending on sorbent regeneration requirements.     

Exploring the potential for improvement of the energy performance of coal fired power plants with post-combustion capture of carbon dioxide

The application of post-combustion capture (PCC) processes in coal fired power stations can result in large reductions of the CO₂-emissions, but the consequential decrease in generation efficiency is an important draw-back. The leading PCC technology is based on chemical absorption processes as this technology is the one whose scale-up status is closest to full-scale capture in power plants. The energy performance of this process is analysed in this contribution. The analysis shows that the potential for improvement of the energy performance is quite large. It is demonstrated that further development of the capture technology and the power plant technology can lead to generation efficiencies for power plants with 90% CO₂ capture which are equivalent to the current generation efficiencies without CO₂ capture, i.e. 0.4 (HHV), leading to an additional resource consumption of 16%. These improvements are possible throughout a combined improvement for the capture process and power generation processes.     

CO2 capture from pre-combustion processes—Strategies for membrane gas separation

The application of membrane gas separation to CO₂ capture from a coal gasification process is one potential solution to reduce greenhouse gas emissions. This review considers the potential for either H₂- or CO₂-selective membranes in an integrated gasification combined cycle (IGCC) process. In particular, the advantages and disadvantages of metallic, porous inorganic and polymeric membranes are considered. This analysis is extended to consider membrane technology as an enhancement to the water-gas shift reaction, to drive the production of hydrogen above the thermodynamic limit. The review concludes with a brief overview of the economics of incorporating membrane gas separation into the IGCC process and gives an indication of the potential economic use of membrane gas separation technology in the IGCC process.     

Thermodynamic analysis on post-combustion CO2 capture of natural-gas-fired power plant

A chemical absorption, post-combustion CO₂ capture unit is simulated and an exergy analysis has been conducted, including irreversibility calculations for all process units. By pinpointing major irreversibilities, new proposals for efficient energy integrated chemical absorption process are suggested. Further, a natural-gas combined-cycle power plant with a CO₂ capture unit has been analyzed on an exergetic basis. By defining exergy balances and black-box models for plant units, investigation has been made to determine effect of each unit on the overall exergy efficiency. Simulation of the chemical absorption plant was done using UniSim Design software with Amines Property Package. For natural-gas combined-cycle design, GT PRO software (Thermoflow, Inc.) has been used. For exergy calculations, spreadsheets are created with Microsoft Excel by importing data from UniSim and GT PRO. Results show the exergy efficiency of 21.2% for the chemical absorption CO₂ capture unit and 67% for the CO₂ compression unit. The total exergy efficiency of CO₂ capture and compression unit is 31.6%.