Testing of hydrotalcite-based sorbents for CO2 and H2S capture for use in sorption enhanced water gas shift

The feasibility of the sorption enhanced water gas shift (SEWGS) process under sour conditions is shown. The sour-SEWGS process constitutes a second generation pre-combustion carbon capture technology for the application in an IGCC. As a first critical step, the suitability of a K₂CO₃ promoted hydrotalcite-based CO₂ sorbent is demonstrated by means of adsorption and regeneration experiments in the presence of 2000 ppm H₂S. In multiple cycle experiments at 400 °C and 5 bar, the sorbent displays reversible co-adsorption of CO₂ and H₂S. The CO₂ sorption capacity is not significantly affected compared to sulphur-free conditions. A mechanistic model assuming two different sites for H₂S interaction explains qualitatively the interactions of CO₂ and H₂S with the sorbent. On the type A sites, CO₂ and H₂S display competitive sorption where CO₂ is favoured. The type B sites only allow H₂S uptake and may involve the formation of metal sulphides. This material behaviour means that the sour-SEWGS process likely eliminates CO₂ and H₂S simultaneously from the syngas and that an almost CO₂ and H₂S-free H₂ stream and a CO₂ + H₂S stream can be produced.     

Calcium oxide for CO2 capture: Operational window and efficiency penalty in sorption-enhanced steam methane reforming

Calcium oxide (CaO) is a material that is being widely investigated in the context of CO₂ capture. One such application is as a CO₂ sorbent in the sorption-enhanced steam methane reforming processes (SERP). CO₂ is captured in an adsorption mode, where the conversion of CH₄ to H₂ is also enhanced, and released later in a separate desorption mode. This work presents an analysis of the relation between different process conditions and parameters during both adsorption and desorption modes. The interrelation between these conditions and the sorbent properties as well as the targeted carbon capture ratio is analysed. Conditions relevant for capturing 85% of carbon in the feed on CaO are determined and interlinked. A steam-to-carbon ratio of 4.2 has been determined to be relevant under 600 °C and 17 bar adsorption conditions. Similarly, process conditions relevant for regenerating the sorbent are determined and interlinked. For purge steam-to-CO₂ ratio of 1.8 at a desorption pressure of 1 bar, relevant desorption temperature has been calculated to be 820 °C. System simulations under these adsorption and desorption conditions resulted in a system efficiency of 50.8%. Effect of tuning process operating conditions on system efficiency as well as the efficiency penalty associated with the regeneration of the sorbent are investigated by process simulations using Aspen Plus^®. Possible system heat integration routes to reduce the efficiency penalty are proposed and the results of the process simulations are presented.     

Experimental validation of in situ CO2 capture with CaO during the low temperature combustion of biomass in a fluidized bed reactor

A novel concept for capturing CO₂ from biomass combustion using CaO as an active solid sorbent of CO₂ is discussed and experimentally tested. According to the CaO/CaCO₃ equilibrium, if a fuel could be burned at a sufficiently low temperature (below 700 °C) it would be possible to capture CO₂ “in situ” with the CaO particles at atmospheric pressure. A subsequent step involving the regeneration of CaCO₃ in a calciner operating at typical conditions of oxyfired-circulating fluidized combustion would deliver the CO₂ ready for purification, compression and permanent geological storage. Several series of experiments to prove this concept have been conducted in a 30 kW interconnected fluidized bed test facility at INCAR-CSIC, made up of two interconnected circulating fluidized bed reactors, one acting as biomass combustor-carbonator and the other as air-fired calciner (which is considered to yield similar sorbent properties than those of an oxyfired calciner). CO₂ capture efficiencies in dynamic tests in the combustor-carbonator reactor were measured over a wide range of operating conditions, including different superficial gas velocities, solids circulation rates, excess air above stoichiometric, and biomass type (olive pits, saw dust and pellets). Biomass combustion in air is effective at temperatures even below the 700 °C, necessary for the effective capture of CO₂ by carbonation of CaO. Overall CO₂ capture efficiencies in the combustor-carbonator higher than 70% can be achieved with sufficiently high solids circulation rates of CaO and solids inventories. The application of a simple reactor model for the combined combustion and CO₂ capture reactions allows an efficiency factor to be obtained from the dynamic experimental test that could be valuable for scaling up purposes.     

Equilibrium studies of copper ion adsorption onto palm kernel fibre

The equilibrium sorption of copper ions from aqueous solution using a new adsorbent, palm kernel fibre, has been studied. Palm kernel fibre is obtained in large amounts as a waste product of palm oil production. Batch equilibrium studies were carried out and system variables such as solution pH, sorbent dose, and sorption temperature were varied. The equilibrium sorption data was then analyzed using the Langmuir, Freundlich, Dubinin–Radushkevich (D–R) and Temkin isotherms. The fit of these isotherm models to the equilibrium sorption data was determined, using the linear coefficient of determination, r², and the non-linear Chi-square, χ² error analysis.The results revealed that sorption was pH dependent and increased with increasing solution pH above the pH_PZC of the palm kernel fibre with an optimum dose of 10 g/dm³. The equilibrium data were found to fit the Langmuir isotherm model best, with a monolayer capacity of 3.17 × 10^?4 mol/g at 339 K. The sorption equilibrium constant, K_a, increased with increasing temperature, indicating that bond strength between sorbate and sorbent increased with temperature and sorption was endothermic. This was confirmed by the increase in the values of the Temkin isotherm constant, B₁, with increasing temperature. The Dubinin–Radushkevich (D–R) isotherm parameter, free energy, E, was in the range of 15.7–16.7 kJ/mol suggesting that the sorption mechanism was ion exchange. Desorption studies showed that a high percentage of the copper was desorbed from the adsorbent using acid solutions (HCl, HNO₃ and CH₃COOH) and the desorption percentage increased with acid concentration. The thermodynamics of the copper ions/palm kernel fibre system indicate that the process is spontaneous and endothermic.     

Prospects for cost-effective post-combustion CO2 capture from industrial CHPs

Industrial Combined Heat and Power plants (CHPs) are often operated at partial load conditions. If CO₂ is captured from a CHP, additional energy requirements can be fully or partly met by increasing the load. Load increase improves plant efficiency and, consequently, part of the additional energy consumption would be offset. If this advantage is large enough, industrial CHPs may become an attractive option for CO₂ capture and storage CCS. We therefore investigated the techno-economic performance of post-combustion CO₂ capture from small-to-medium-scale (50–200 MWe maximum electrical capacity) industrial Natural Gas Combined Cycle- (NGCC-) CHPs in comparison with large-scale (400 MWe) NGCCs in the short term (2010) and the mid-term future (2020–2025). The analyzed system encompasses NGCC, CO₂ capture, compression, and branch CO₂ pipeline.The technical results showed that CO₂ capture energy requirement for industrial NGCC-CHPs is significantly lower than that for 400 MWe NGCCs: up to 16% in the short term and up to 12% in the mid-term future. The economic results showed that at low heat-to-power ratio operations, CO₂ capture from industrial NGCC-CHPs at 100 MWe in the short term (41–44 €/tCO₂ avoided) and 200 MWe in the mid-term future (33–36 €/tCO₂ avoided) may compete with 400 MWe NGCCs (46–50 €/tCO₂ avoided short term, 30–35 €/tCO₂ avoided mid-term).     

Parametric investigation of the calcium looping process for CO2 capture in a 10 kWth dual fluidized bed

Calcium looping (CaL) is a promising post-combustion CO₂ capture technology which is carried out in a dual fluidized bed (DFB) system with continuous looping of CaO, the CO₂ carrier, between two beds. The system consists of a carbonator, where flue gas CO₂ is adsorbed by CaO and a regenerator, where captured CO₂ is released. The CO₂-rich regenerator flue gas can be sequestered after gas processing and compression. A parametric study was conducted on the 10 kW_th DFB facility at the University of Stuttgart, which consists of a bubbling fluidized bed carbonator and a riser regenerator. The effect of the following parameters on CO₂ capture efficiency was investigated: carbonator space time, carbonator temperature and calcium looping ratio. The active space time in the carbonator, which is a function of the space time and the calcium looping ratio, was found to strongly correlate with the CO₂ capture efficiency. BET and BJH techniques provided surface area and pore volume distribution data, respectively, for collected sorbent samples. The rate of sorbent attrition was found to be 2 wt.%/h which is below the expected sorbent make-up rate required to maintain sufficient sorbent activity. Steady-state CO₂ capture efficiencies greater than 90% were achieved for different combinations of operational parameters. Moreover, the experimental results obtained were briefly compared with results derived from reactor modeling studies. Finally, the implications of the experimental results with respect to commercialization of the CaL process have been assessed.     

Carbonic anhydrase-facilitated CO2 absorption with polyacrylamide buffering bead capture

A novel CO₂ separation concept is described wherein the enzyme carbonic anhydrase (CA) is used to increase the overall rate of CO₂ absorption after which hydrated CO₂ reacts with regenerable amine-bearing polyacrylamide buffering beads (PABB). Following saturation of the material's immobilized tertiary amines, CA-bearing carrier water is separated and recycled to the absorption stage while CO₂-loaded material is thermally regenerated. Process application of this concept would involve operation of two or more columns in parallel with thermal regeneration with low-pressure steam taking place after the capacity of a column of amine-bearing polymeric material was exceeded. PABB CO₂-bearing capacity was evaluated by thermogravimetric analysis (TGA) for beads of three acrylamido buffering monomer ingredient concentrations: 0 mol/kg bead, 0.857 mol/kg bead, and 2 mol/kg bead. TGA results demonstrate that CO₂-bearing capacity increases with increasing PABB buffering concentration and that up to 78% of the theoretical CO₂-bearing capacity was realized in prepared PABB samples (0.857 mol/kg recipe). The highest observed CO₂-bearing capacity of PABB was 1.37 mol of CO₂ per kg dry bead. TGA was also used to assess the regenerability of CO₂-loaded PABB. Preliminary results suggest that CO₂ is partially driven from PABB samples at temperatures as low as 55 °C, with complete regeneration occurring at 100 °C. Other physical characteristics of PABB are discussed. In addition, the effectiveness of bovine carbonic anhydrase for the catalysis of CO₂ dissolution is evaluated. Potential benefits and drawbacks of the proposed process are discussed.     

Integration and evaluation of a power plant with a CaO-based CO2 capture system

This paper explores the integration and evaluation of a power plant with a CaO-based CO₂ capture system. There is a great amount of recoverable heat in the CaO-based CO₂ capture process. Five cases for the possible integration of a 600 MW power plant with CaO-based CO₂ capture process are considered in this paper. When the system is configured so that recovered heat is used to replace part of the boiler heat load (Case 2), modelling not only shows that this is the system recovering the most heat of 1008.8 MW but also results in the system with the lowest net power output of 446 MW and the second lowest of efficiency of 34.1%. It is indicated that system performance depends both on the amount of heat recovery and the type of heat utilization. When the system is configured so that a 400 MW power plant is built using the recovered heat (Case 4), modelling shows that this is the system with the most net power output of 846 MW, the highest efficiency of 36.8%, the lowest cost of electricity of 54.3 €/MWh and the lowest cost of CO₂ avoided of 28.9 €/tCO₂. This new built steam cycle will not affect the operation of the reference plant which vents its CO₂ to the atmosphere, highly reducing the connection between the CO₂ capture process and the reference plant which vents its CO₂ to the atmosphere. The average cost of electricity and the cost of CO₂ avoided of the five cases are about 58.9 €/kWh and 35.9 €/tCO₂, respectively.     

Multi-stage chemical looping combustion (CLC) for combined cycles with CO2 capture

This paper presents application of the chemical looping combustion (CLC) method in natural gas-fired combined cycles for power generation with CO₂ capture. A CLC combined cycle consisting of single CLC-reactor system, an air turbine, a CO₂-turbine and a steam cycle has been designated as the base-case cycle. The base-case cycle can achieve net plant efficiency of about 52% at an oxidation temperature of 1200 °C. In order to achieve a reasonable efficiency at lower oxidation temperatures, reheat is introduced into the air turbine by employing multi CLC-reactors. The results show that the single reheat CLC-combined cycle can achieve net plant efficiency of above 51% at oxidation temperature of 1000 °C and above 53% at the oxidation temperature of 1200 °C including CO₂ compression to 110 bar. The double reheat cycle results in marginal efficiency improvement as compared to the single reheat cycle. The CLC-cycles are also compared with a conventional combined cycle with and without post-combustion capture in amine solution. All the CLC-cycles show higher net plant efficiencies with close to 100% CO₂ capture as compared to a conventional combined cycle with post-combustion capture, which is very promising.     

Pathways towards large-scale implementation of CO2 capture and storage: A case study for the Netherlands

We sketch four possible pathways how carbon dioxide capture and storage (CCS) (r)evolution may occur in the Netherlands, after which the implications in terms of CO₂ stored and avoided, costs and infrastructural requirements are quantified. CCS may play a significant role in decarbonising the Dutch energy and industrial sector, which currently emits nearly 100 Mt CO₂/year. We found that 15 Mt CO₂ could be avoided annually by 2020, provided some of the larger gas fields that become available the coming decade could be used for CO₂ storage. Halfway this century, the mitigation potential of CCS in the power sector, industry and transport fuel production is estimated at maximally 80–110 Mt CO₂/year, of which 60–80 Mt CO₂/year may be avoided at costs between 15 and 40 €/t CO₂, including transport and storage. Avoiding 30–60 Mt CO₂/year by means of CCS is considered realistic given the storage potential represented by Dutch gas fields, although it requires planning to assure that domestic storage capacity could be used for CO₂ storage. In an aggressive climate policy, avoiding another 50 Mt CO₂/year may be possible provided that nearly all capture opportunities that occur are taken. Storing such large amounts of CO₂ would only be possible if the Groningen gas field or large reservoirs in the British or Norwegian part of the North Sea will become available.     

Ionic liquids for post-combustion CO2 absorption

The present work is a study to evaluate ionic liquids as a potential solvent for post-combustion CO₂ capture. In order to enhance the absorption performance of a CO₂ capture unit, different ionic liquids have been designed and tested. The main goal was to get a comparison between a reference liquid and selected ionic liquids. As the reference, a solution of 30 w% monoethanolamine (MEA) and water was used. A large range of different pure and diluted ionic liquids was tested with a special screening process to gain general information about the CO₂ absorption performance. Based on these results, a 60 w% ionic liquid solution in water was selected and the vapour–liquid equilibrium was measured experimentally between 40 °C and 110 °C. From these curves the enthalpy of absorption for capturing CO₂ into the ionic liquid was determined. With these important parameters one is able to calculate the total energy demand for stripping of CO₂ from the loaded solvent for comparison of the ionic liquid based solvent with the reference MEA solvent. The energy demand of this 60 w% ionic liquid is slightly lower than that of the reference solution, resulting in possible energy savings between 12 and 16%.     

Gas conditioning—The interface between CO2 capture and transport

Gas conditioning is commonly referred to as the required processing for a produced natural gas to achieve transport and sales specifications. In this paper, gas conditioning as the processing required in the interface between CO₂ capture and transport is studied for nine different natural gas fired power plant concepts and three different CO₂ transport processes. Conditioning processes for both pipeline and ship transport are described and an enhanced process for volatile removal is developed. The energy requirement for the conditioning processes is normally between 90 and 120 kWh/tonne CO₂; however, this depends on the pressure and composition of the captured CO₂-rich stream. The loss of CO₂ in the water purge is small for most capture processes. The waste streams from the gas conditioning processes can contain large amounts of CO₂ and should therefore be further processed or reintroduced at an appropriate point upstream in the capture or gas conditioning process if possible. The integration benefit may vary depending on the composition of the CO₂-rich stream. It could be particularly interesting for processes with “innovative reactors” (membranes, sorbents, chemical looping) to integrate CO₂ capture and gas conditioning.     

Amine volatility in CO2 capture

Amine volatility is a key screening criterion for amines to be used in CO₂ capture. Excessive volatility may result in significant economic losses and environmental impact. It also dictates the capital cost of the water wash. This paper reports measured amine volatility in 7 m MEA (monoethanolamine), 8 m PZ (piperazine), 7 m MDEA (n-methyldiethanolamine)/2 m PZ (piperazine), 12 m EDA (ethylenediamine), and 5 m AMP (2-amino-2-methyl-1-propanol) at 40–60 °C with lean and rich loadings giving CO₂ partial pressures of 0.5 and 5 kPa at 40 °C. The amine concentrations were chosen to maximize CO₂ capture capacity at acceptable viscosity. At the lean loading condition (where volatility is of greatest interest), the amines are ranked in order of increasing volatility: 7 m MDEA/2 m PZ (6/2 ppm), 8 m PZ (8 ppm), 12 m EDA (9 ppm), 7 m MEA (31 ppm), and 5 m AMP (112 ppm). The apparent amine partial molar excess enthalpies in these systems were estimated to range from ～10 to 87 kJ/mol of amine.     

Conceptual design of a three fluidised beds combustion system capturing CO2 with CaO

In this work, the Aspen Hysys conceptual design of a new process for energy generation at large scale with implicit CO₂ capture is presented. This process makes use of the CaO capability for CO₂ capture at high temperature and the possibility of regenerating this sorbent working in interconnected fluidised bed reactors operating at different temperatures. The proposed process has the advantage of producing power with minimum CO₂ emissions and very low energy penalties compared with similar air-based combustion power plants. In this system, five main parts can be distinguished: the combustor where coal is burnt with air, the calciner where the fresh and the recycled CaCO₃ is calcined, the carbonator where the CO₂ produced in the combustor is captured, the supercritical steam cycle and the CO₂ compression system. In this arrangement, the three fluidised bed reactors are interconnected in such a way that it is possible to perform the CaCO₃ calcination at a temperature of 950 °C with the energy transported by a hot solid stream produced in the circulating fluidised bed combustor operating at 1030 °C. The stream rich in CaO produced in the calciner is split into three parts. One of them is transported to the carbonator operating at 650 °C where most of the CO₂ in the flue gas produced in the combustor is captured. The second one is sent to the combustor, where it is heated up and used as energy carrier. The third solid stream that leaves the calciner is a purge in order to maintain the capture system activity and to avoid inert material accumulation. Because of the high temperatures involved in all the system, it is possible to recover most of the energy in the fuel and to produce power in a supercritical steam cycle. A case study is presented and it is demonstrated that under these operating conditions, 90% CO₂ capture efficiency can be achieved with no energy penalty further than the one originated in the CO₂ compression system.     

Carbon dioxide capture with concentrated,aqueous piperazine

Concentrated, aqueous piperazine (PZ) has been investigated as a novel amine solvent for carbon dioxide (CO₂) absorption. The CO₂ absorption rate of aqueous PZ is more than double that of 7 m MEA and the amine volatility at 40 °C ranges from 11 to 21 ppm. Thermal degradation is negligible in concentrated, aqueous PZ up to a temperature of 150 °C, a significant advantage over MEA systems. Oxidation of concentrated, aqueous PZ is appreciable in the presence of copper (4 mM), but negligible in the presence of chromium (0.6 mM), nickel (0.25 mM), iron (0.25 mM), and vanadium (0.1 mM). Initial system modeling suggests that 8 m PZ will use 10–20% less energy than 7 m MEA. The fast mass transfer and low degradation rates suggest that concentrated, aqueous PZ has the potential to be a preferred solvent for CO₂ capture.     

CO2 capture from power plants: Part II. A parametric study of the economical performance based on mono-ethanolamine

While the demand for reduction in CO₂ emission is increasing, the cost of the CO₂ capture processes remains a limiting factor for large-scale application. Reducing the cost of the capture system by improving the process and the solvent used must have a priority in order to apply this technology in the future. In this paper, a definition of the economic baseline for post-combustion CO₂ capture from 600 MW_e bituminous coal-fired power plant is described. The baseline capture process is based on 30% (by weight) aqueous solution of monoethanolamine (MEA). A process model has been developed previously using the Aspen Plus simulation programme where the baseline CO₂-removal has been chosen to be 90%. The results from the process modelling have provided the required input data to the economic modelling. Depending on the baseline technical and economical results, an economical parameter study for a CO₂ capture process based on absorption/desorption with MEA solutions was performed.Major capture cost reductions can be realized by optimizing the lean solvent loading, the amine solvent concentration, as well as the stripper operating pressure. A minimum CO₂ avoided cost of € 33 tonne⁻¹ CO₂ was found for a lean solvent loading of 0.3 mol CO₂/mol MEA, using a 40 wt.% MEA solution and a stripper operating pressure of 210 kPa. At these conditions 3.0 GJ/tonne CO₂ of thermal energy was used for the solvent regeneration. This translates to a € 22 MWh⁻¹ increase in the cost of electricity, compared to € 31.4 MWh⁻¹ for the power plant without capture.     

CO2 capture from hot stove gas in steel making process

The capture of CO₂ from a hot stove gas in steel making process containing 30 vol% CO₂ by chemical absorption in a rotating packed bed (RPB) was studied. The RPB had an inner diameter of 7.6 cm, an outer diameter of 16 cm, and a height of 2 cm. The aqueous solutions containing 30 wt% of single and mixed monoethanolamine (MEA), 2-(2-aminoethylamino)ethanol (AEEA), and piperazine (PZ) were used. The CO₂ capture efficiency was found to increase with increasing temperature in a range of 303–333 K. It was also found to be more dependent on gas and liquid flow rates but less dependent on rotating speed when the speed was higher than 700 rpm. The obtained results indicated that the mixed alkanolamine solutions containing PZ were more effective than the single alkanolamine solutions. This was attributed to the highest reaction rate of PZ with CO₂. A higher portion of PZ in the mixture was more favorable to CO₂ capture. The highest gas flow rates allowed to achieve a desired CO₂ capture efficiency and the correspondent height of transfer unit (HTU) were determined at different aqueous solution flow rates. Because all the 30 wt% single and mixed alkanolamine solutions could result in a HTU less than 5.0 cm at a liquid flow rate of 100 mL/min, chemical absorption in a RPB instead of a packed bed adsorber is therefore suggested to capture CO₂ from the flue gases in steel making processes.     

Study on CO2 capture using dry potassium-based sorbents through orthogonal test method

The effect of reaction conditions on the carbonation characteristics of K₂CO₃ calcined from KHCO₃ was investigated with a pressurized thermogravimetric apparatus. Results show that the conversion rate decreased as the reaction temperature and pressure increased, and the effect of CO₂ and H₂O concentration is little. The mean reaction rate maintained constant of 3%/min. The maximum reaction rate increased as the temperature and H₂O concentration increased, and the pressure decreased. The reaction temperature and pressure are the key factors, and it is important to control those carefully for this technique. The optimum reaction condition is 60 °C, 18% CO₂, 18% H₂O, and 1 atm. K₂CO₃ calcined from KHCO₃ showed excellent CO₂ capture capability in this condition.     

Carbon dioxide storage capacity in uneconomic coal beds in Alberta,Canada: Methodology,potential and site identification

Methodology is presented for a first-order regional-scale estimation of CO₂ storage capacity in coals under sub-critical conditions, which is subsequently applied to Cretaceous-Tertiary coal beds in Alberta, Canada. Regions suitable for CO₂ storage have been defined on the basis of groundwater depth and CO₂ phase at in situ conditions. The theoretical CO₂ storage capacity was estimated on the basis of CO₂ adsorption isotherms measured on coal samples, and it varies between ∼20 kt CO₂/km² and 1260 kt CO₂/km², for a total of approximately 20 Gt CO₂. This represents the theoretical storage capacity limit that would be attained if there would be no other gases present in the coals or they would be 100% replaced by CO₂, and if all the coals will be accessed by CO₂. A recovery factor of less than 100% and a completion factor less than 50% reduce the theoretical storage capacity to an effective storage capacity of only 6.4 Gt CO₂. Not all the effective CO₂ storage capacity will be utilized because it is uneconomic to build the necessary infrastructure for areas with low storage capacity per unit surface. Assuming that the economic threshold to develop the necessary infrastructure is 200 kt CO₂/km², then the CO₂ storage capacity in coal beds in Alberta is greatly reduced further to a practical capacity of only ∼800 Mt CO₂.