The use of XAD-resins for the detection of mutagenic activity in water: I. Studies with surface water

A study of the effects of different XAD-resins, bed volume, flow rate, pH and type of eluent on the extraction of organic mutagens from surface water is presented. XAD-4/8 is as effective as XAD-2 in concentrating organic mutagens from surface water and dimethylsulfoxide (DMSO) is as efficient as acetone in eluting the adsorbed organic mutagens. The latter allows direct testing up to 0.5 ml of DMSO concentrate in the Ames test. Variation of the pH of the water after passing the XAD-4/8, followed by readsorption, shows that the majority of the mutagenic activity due to dissolved organics is adsorbed at neutral pH. Only a minor fraction is readsorbed at pH 3. Further a XAD-4/8 concentrate and a similar concentrate prepared by freeze drying gives similar mutagenic activity. This indicates that many of the organic mutagens are recovered in the XAD-4/8 concentrate.It is concluded that adsorption on XAD-4/8, followed by direct testing of the DMSO eluates in the Ames test, presents a rapid and relatively simple way to detect low concentrations of organic mutagens in surface water. The general suitability of the method is shown for different types of surface water.     

Competitive adsorption of dye metanil yellow and RB15 in acid solutions on chemically cross-linked chitosan beads

One kind of adsorbent with a high adsorption capacity for anionic dyes was prepared using ionically and chemically cross-linked chitosan beads. A batch system was applied to study the adsorption behavior of one acid dye (MY, metanil yellow) and one reactive dye (RB15, reactive blue 15) in aqueous solutions by the cross-linked chitosan beads. The adsorption capacities was 3.56 mmol g(-1) (1334 mg g(-1)) for dye MY and 0.56 mmol g(-1) (722 mg g(-1)) for dye RB15 at pH4, 30 degrees C. The Langmuir model agreed very well with the experimental data (R(2)>0.996). The kinetics of adsorption for a single dye and the kinetics of removal of ADMI color value in mixture solutions at different initial dye concentrations were evaluated by the nonlinear first-order and second-order models. The first-order kinetic model fits well with the dynamical adsorption behavior of a single dye for lower initial dye concentrations, while the second-order kinetic model fits well for higher initial dye concentrations. The competitive adsorption favored the dye RB15 in the mixture solution (initial conc. (mM): MY=1.34; RB15=1.36); while it favored the dye MY in the mixture solution (initial conc. (mM): MY=3.00; RB15=1.34) and the adsorption kinetics for dye RB15 has the tendency to shift to a slower first order model.     

Low-cost adsorbents from bio-waste for the removal of dyes from aqueous solution

Activated carbons (ACs) were developed from bio-waste materials like rice husk and peanut shell (PS) by various physicochemical activation methods. PS char digested in nitric acid followed by treatment at 673 K resulted in high surface area up to ～585 m²/g. The novelty of the present study is the identification of oxygen functional groups formed on the surface of activated carbons by infrared and X-ray photoelectron spectroscopy and quantification by using temperature programmed decomposition (TPD). Typical TPD data indicated that each activation method may lead to varying amounts of acidic and basic functional groups on the surface of the adsorbent, which may be a crucial factor in determining the adsorption capacity. It was shown that ACs developed during the present study are good adsorbents, especially for the removal of a model textile dye methylene blue (MB) from aqueous solution. As MB is a basic dye, H₂O₂-treated rice husk showed the best adsorption capacity, which is in agreement with the acidic groups present on the surface. Removal of the dye followed Langmuir isotherm model, whereas MB adsorption on ACs followed pseudo-second-order kinetics.     

Adsorption of Pb(II) on variable charge soils amended with rice-straw derived biochar

Two Ultisols and one Oxisol from tropical regions of southern China were incubated with rice straw biochar to investigate the effect of biochar on their surface charge and Pb(II) adsorption using batch methods. The incorporation of biochar induced a remarkable increase in soil cation exchange capacity after 30 d of incubation. The incorporation of biochar significantly increased the adsorption of Pb(II) by these variable charge soils; the enhancement of adsorption of Pb(II) by these soils increased with the addition level of biochar. Adsorption of Pb(II) involved both electrostatic and non-electrostatic mechanisms; however, biochar mainly increased Pb(II) adsorption through the non-electrostatic mechanism via the formation of surface complexes between Pb²⁺ and functional groups on biochar. There was greater enhancement of biochar on the non-electrostatic adsorption of Pb(II) by the variable charge soils at relatively low pH. Therefore, the incorporation of biochar decreased the activity and availability of Pb(II) to plants through increased non-electrostatic adsorption of Pb(II) by acidic variable charge soils.     

The effect of pH, temperature, and molecular size on the removal of dyes from textile effluent using manganese oxides-modified diatomite.

This work is an investigation on the use of manganese oxides-modified diatomite (MOMD) for the removal of color from textile wastewaters. The modification of the diatomite was carried out by treatment with manganese oxides; delta-bimessite type resulted. The surface area, pH(ZPC), Fourier transform infrared (FTIR), and scanning electron microscopy of MOMD were studied. The influence of concentration, pH, particle size, and temperature on the adsorption capacities of methylene blue (MB) and hydrolyzed reactive black (RB) and reactive yellow (RY) was investigated. Key thermodynamic parameters such as deltaH degrees, deltaS degrees, and deltaG degrees were also determined. The deltaH degrees of MB and hydrolyzed RB and RY was +94.64, -143.1, and -38.78 kJ/mol, respectively, whereas the deltaG degrees values of -17.68, -27.93, and -23.26 kJ/mol were obtained, indicating a spontaneous process with low activation-energy requirements. The findings further indicated that coulomb interaction, molecular size, and orientation of the dye and its surface charge played an important role in the adsorption and attachment of the dyes to the bimessite layers of MOMD.     

Sorption behavior of bensulfuron-methyl on andisols and ultisols volcanic ash-derived soils: Contribution of humic fractions and mineral-organic complexes

Bensulfuron-methyl sorption was studied in Andisol and Ultisol soils in view of their characteristic physical and chemical properties, presenting acidic pH and variable charge. Humic and fulvic acids (HA and FA) and humin (HUM) contributions were established. Sorption was studied by using two synthetic sorbents, an aluminum-silicate with iron oxide coverage and the same sorbent coated with humic acid. Freundlich model described Bensulfuron-methyl behavior in all sorbents (R² 0.969-0.998). K_f for soils (8.3-20.7 μg^1−1/n mL^1/n g⁻¹) were higher than those reported in the literature. Organic matter, halloysite or kaolinite, and specific surface area contributed to the global process. The highest K_f for HA, FA and HUM were 539.5, 82.9, and 98.7 μg^1−1/n mL^1/n g⁻¹. Model sorbents described the participation of variable charge materials with high adsorption capacity. The constant capacitance model was used to assess effects of Bensulfuron-methyl adsorption on the distribution of SOH, SOH₂⁺ and SO⁻ sites of sorbents.     

The removal of reactive black 5 from aqueous solutions by cotton seed shell

This study investigated the removal of Reactive Black 5 (RB5) textile dye from aqueous solutions using cotton (Gossypium hirsutum) seed shell (CSS) as low cost adsorbents. The data were described according to the Freundlich and Langmuir isotherm models. Of these, the Langmuir model provided the best fit for the experimental data. The highest measured adsorption density was 12.19 mg/g at pH 2. An equilibrium adsorption rate of RB5 by CSS (q(e) = 11.879 mg/g) was observed at 30 minutes. In order to evaluate the adsorption kinetic mechanisms, pseudo first and second order rate kinetic models and an intraparticle diffusion model were applied, with the pseudo second order model providing an excellent fit for the data.     

Adsorption of pesticides on resins

The objective of this work was to assess the capability of organic hydrophobic polymeric resins Amberlite XAD-4 and XAD-7 to remove the pesticides alachlor and amitrole from water. The pesticides adsorption on the two different adsorbents was measured by batch equilibrium technique and isotherm types and parameters were estimated. Two theoretical models were applied based on a Freundlich and a Langmuir isotherms. The effect of pesticides chemical composition and structure as well as the nature of solid surface on the efficiency of adsorption was evaluated. The influence of pH also was studied. In low pH solutions adsorption of amitrole was higher upon the nonionic aliphatic acrylic ester copolymer XAD-7 in comparison to the nonionic, crosslinked macroreticular copolymer of styrene divinylbenzene XAD-4. In neutral and intermediate pH solutions the polar acrylic ester copolymer XAD-7 was more effective to the retention of alachlor. The acrylic ester copolymer showed at pH 3 the lower effectiveness in alachlor removal from water. The data of the adsorption isotherms of pesticides upon the examined polymeric resins seemed to conform to both the Freundlich and the Langmuir isotherm models.     

表面活性剂改性活性炭对阳离子染料的吸附

以阴离子表面活性剂十二烷基硫酸钠(SDS)为改性剂对粉末活性炭(AC)改性,研究了SDS在活性炭表面的吸附稳定性,用比表面积测定仪、Zeta电位测定仪对改性前后活性炭进行表征,并将其用于吸附模拟废水中的阳离子染料。结果表明,改性剂SDS浓度等于临界胶束浓度时,改性后活性炭(SDS-AC)对SDS吸附稳定,SDS在纯水和染料溶液中的解吸率分别为19.4%和1.6%。pH对活性炭吸附阳离子橙染料影响较小,SDS-AC和AC对染料的吸附平衡时间分别为4 h和12 h,SDS-AC和AC对阳离子橙染料的吸附动力学模型符合拟二级反应模型,吸附等温线更符合Langmuir吸附等温方程,SDS-AC对阳离子橙染料的最大吸附量较AC提高47.8%,SDS-AC对阳离子橙染料的吸附机制为物理吸附和化学吸附共同作用下的单分子层吸附,其中化学吸附是主要控速步骤。     

The pH-dependent adsorption of tributyltin to charcoals and soot

Widespread use of tributyltin (TBT) poses a serious environmental problem. Adsorption by black carbon (BC) may strongly affect its behavior. The adsorption of TBT to well characterized soot and two charcoals with specific surface area in the range of 62-111 m² g⁻¹ have been investigated with main focus on pH effects. The charcoals but not soot possess acidic functional groups. TBT adsorption reaches maximum at pH 6-7 for charcoals, and at pH > 6 for soot. Soot has between 1.5 and 15 times higher adsorption density (0.09-1.77 μmol m⁻²) than charcoals, but charcoals show up to 17 times higher sorption affinities than soot. TBT adsorption is successfully described by a new pH-dependent dual Langmuir model considering electrostatic and hydrophobic adsorption, and pH effects on TBT speciation and BC surface charge. It is inferred that strong sorption of the TBTOH species to BC may affect TBT toxicity.     

Highly effective removal of 2,4-dinitrophenolic from surface water and wastewater samples using hydrophilic molecularly imprinted polymers

Novel hydrophilic molecularly imprinted polymers (MIPs) with high adsorption capacity were used as the sorbents to remove 2,4-dinitrophenol (2,4-DNP) from surface water and wastewater samples. Kinetic studies, dynamic adsorption and selectivity experiments of hydrophilic MIPs were investigated in this study. The results indicated that the maximum adsorption capacity of 2,4-DNP on hydrophilic MIPs was 138.9 mg g^?1 and kinetic experimental data were described by the pseudo-second-order model. Furthermore, the effects of flow rate, initial concentration, pH value, and humic acid on the removal efficiency of 2,4-DNP were optimized. Compared with the active carbon, carbon nanotube, C18 sorbents and common MIPs, the removal efficiency of hydrophilic MIPs (100 mg) was very high with all above 92 % even though the sampling volume was more than 1 L. Investigated results of five times adsorption–desorption cycles indicated hydrophilic MIPs were high stability. In a word, the obtained results demonstrated that hydrophilic MIPs could be used as the effective sorbents for 2,4-DNP removal in practical application.     

Color and COD removal from wastewater containing Reactive Black 5 using Fenton's oxidation process

In this study, Reactive Black 5 (RB5) was removed from synthetic wastewater using Fenton's oxidation (FO) process. Experiments were conducted on the samples containing 100 and 200 mg l(-1) of RB5 to remove the dye toxicity. Seventy-five milligram per litre of RB5 caused 25% toxicity on 24-h born daphnids whereas 100 mg l(-1) of RB5 displayed 100% toxicity on Daphnia magna. The study was performed in a systematic approach searching optimum values of FeSO(4) and H(2)O(2) concentrations, pH and temperature. Optimum pH and temperature for 100 mg l(-1) of RB5 were observed as 3.0 and 40 degrees C, respectively, using 100 mg l(-1) of FeSO(4) and 400 mg l(-1) of H(2)O(2) resulted in 71% chemical oxygen demand (COD) and 99% color removal. For 200 mg l(-1) of RB5, 84% COD removal was obtained using 225 mg l(-1) of FeSO(4) and 1000 mg l(-1) of H(2)O(2) yielding 0.05 molar ratio at pH 3.0 and 40 degrees C. Color removal was also more than 99%. The optimum conditions determined in accordance with the literature data. The H(2)O(2) requirement seems to be related to initial COD of the sample. FeSO(4)/H(2)O(2) ratios found were not changed for both concentrations. The temperature affected the COD removal significantly at high degrees. Toxicity was completely removed for each concentration of RB5 at optimum removal conditions.     

Biosorption of Cr3+, Cd2+ and Cu2+ ions by blue-green algae Spirulina sp.: kinetics, equilibrium and the mechanism of the process

The process of biosorption of heavy metal ions (Cr3+, Cd2+, Cu2+) by blue-green algae Spirulina sp. is discussed in this paper. Spirulina sp. was found to be a very efficient biosorbent. The aim of the present study was to investigate quantitatively the potential binding sites present at the surface of Spirulina sp., using both potentiometric titrations and adsorption isotherms. The kinetic experiments showed that the process equilibrium was reached quickly, in less than 5-10 min. It was found that the equilibrium dependence between biosorption capacity and bulk metal ion concentration could be described with Langmuir equation. This suggests that the mechanism of biosorption is rather chemisorption than physical adsorption and was further confirmed by the low surface area associated with physical adsorption and by the presence of cations that appeared in the solution after biosorption. The maximum contribution of physical adsorption in the overall biosorption process was evaluated as 3.7%. It was proposed that functional groups on the cell surface contributed to the binding of metal ions by a biosorbent via equilibrium reaction. Three functional groups capable of cation exchange were identified on the cell surface. The biomass was described as weakly acidic ion exchanger. Since deprotonation of each functional group depends on pH, the process of biosorption is strongly pH-dependent. This was confirmed in the biosorption experiments carried out at different pH. The contribution of functional groups in the biosorption process was confirmed by chemical modification of the groups. Chemically blocked groups did not show neither biosorption nor ion-exchange capabilities. It has been shown that growth conditions can affect the metal adsorption properties of microalgae. The paper also discusses desorption characteristics of the biosorbent. The criteria for desorption were high elution efficiency and preservation of biosorptive properties. Desorbent that possessed these characteristics was nitric acid.     

Ozonation of an azo dye C.I. Remazol Black 5 and toxicological assessment of its oxidation products

The effect of ozonation (20.5 mgl(-1)) on the degradation processes of an azo dye, Remazol Black 5 (RB5; CI) was studied. Conventional parameters such as chemical oxygen demand (COD), total organic carbon (TOC), pH, conductivity, colour removal, biodegradability (BOD(5/28)), and toxic potential of the dye and its degradation products were monitored during the process. The results obtained indicated that ozonation is a highly effective way to remove the colour of a corresponding dye solution. However, a considerable organic load still remained as indicated by high COD and TOC residues. The COD, TOC reductions were about 40% and 25% for 6 h ozonation of 2 gl(-1) RB5 aqueous solution. During the ozonation process the rapid decrease of pH and the sharp increase of conductivity indicated the formation of acidic by-products and small fragments and ions which were identified by high performance ion chromatography. The BOD28 data revealed that first by-products after partial ozonation (10-150 min) of RB5 were more biodegradable than the parent compound and ozonation can enhance the biodegradability of azo dyes. During the first 150 min of total 360 min of oxidation, the formation of first by-products with high toxic potential took place as it could be confirmed by two acute toxicity-screening tests, the bioluminescence test (Vibrio fischerii) and the neutral red cytotoxicity assay (rat hepatoma cells). The significant enhancement of microbial biodegradability after long-term ozonation could also be seen as a decrease of toxic intermediates in correlation with the ozonation time as indicated in BOD28 biological degradation test results.     

Two stage biological treatment of a diazo reactive textile dye and the fate of the dye metabolites

A two stage anaerobic/aerobic bacterial process was used to decolorize and partially mineralize a reactive vinyl sulfone diazo dye C.I. Reactive Black 5 (RB5) in a synthetic wastewater. Since the anchor group of reactive dyes reacts during the dyeing process, the effect the degree of hydrolysis of the vinyl sulfone dye had on decolorization, mineralization and toxicity in each stage was investigated. An overall color removal of approximately 65% was found for both the fully and partially hydrolyzed dye. Partial mineralization of the fully hydrolyzed RB5 was achieved in the two stage rotating disc reactors. While the anchor group metabolite p-aminobenzene-2-hydroxyethylsulfonic acid (p-ABHES) was mineralized, an oxidized form of the center metabolite (1,2-ketimino-7-amino-8-hydroxynaphthalene-3,6-disulfonic acid) remained in the aerobic stage effluent, causing the effluent to be colored although no RB5 was present. Partially hydrolyzed dye in the influent with vinyl forms of the anchor group caused cessation of biogas production and a reduction in decolorization efficiency in the anaerobic stage. No evidence for mineralization of the partially hydrolyzed dye or its metabolites was found. A method for evaluating dye mineralization using lumped parameters is presented.     

交联壳聚糖对重金属离子的吸附性能研究

以海蟹壳为原料制备的壳聚糖在碱性条件下,经环氧氯丙烷交联制得水不溶性的交联壳聚糖,采用静态法研究交联壳聚糖对Ｃｕ＾２＋,Ｃｒ＾３＋,Ｎｉ＾２＋,Ｐｂ＾２＋,Ｚｎ＾２＋,Ｈｇ＾２＋等几种重金属离子的吸附性能及ｐＨ值对吸附性能的影响,探讨了它们的作用机理。     

Equilibrium and kinetic studies on the adsorption of aniline compounds from aqueous phase onto bifunctional polymeric adsorbent with sulfonic groups

In the present study, a hydrophilic bifunctional polymeric resin (LS-2) with sulfonic groups was synthesized, and the adsorption performance of three aniline compounds, aniline, 4-methylaniline, and 4-nitroaniline onto LS-2 was compared with that on the commercial Amberlite XAD-4. The uptake of the aniline compounds on LS-2 is a procedure of coexistence of physisorption and chemisorption and obeys the pseudo-second order rate equation, while the uptake of the compounds on XAD-4 is merely a physical adsorption and follows the pseudo-first order rate equation. All the isothermal data fit well with the Freundlich model, and the values of K(F) of the compounds adsorbing on LS-2 are much higher than those on XAD-4 suggesting the higher adsorbing capacities on LS-2 than those on XAD-4, which may be attributed to the microporous structure and the polar groups on the network of LS-2 resin. Dynamic adsorption and desorption studies for aniline on LS-2 show that the breakthrough adsorption capacity and the total adsorption capacity are 0.96 and 1.24 mmol per milliliter resin, respectively. Nearly 100% regeneration efficiency for the adsorbent was achieved by 5% hydrochloric acid.     

Removal of 2-chlorophenol from water using rice-straw derived ash

Removal of 2-chlorophenol from water using rice-straw derived ash (RSDA) was evaluated in this study to compare with commercial activated carbon. RSDA was obtained by burning rice-straw at 400 °C and 700 °C for 1 h. This ash can provide a better adsorbent for 2-chlorophenol. The adsorption capacities of RSDA at 400 °C and 700 °C are 37 and 52 mg g?1 at pH 4, respectively, and decrease to 9.0 and 40 mg g?1 at pH 10. Adsorption of either neutral or anionic 2-cholorphenol by the RSDA are shown as L-shaped nonlinear isotherms, suggesting surface adsorption rather than partitioning is occurring. At higher-burning temperatures, the surface area, porosity, point of zero charge and aromaticity of the resultant RSDA increase, but the oxygen content and surface acidity decrease. The combined effects result in a higher 2-chlorophenol adsorption of RSDA at 700 °C, which shows a slight pH effect on the adsorption of 2-chlorophenol, due to the lower content of oxygen-containing functional groups. Oxygen-containing functional groups contribute to surface acidity and H-bonding sites for adsorbed water, which compromises the interaction between 2-chlorophenol and the adsorbents. Thus, it suggests that rice-straw derived carbon (RSDC) can be used as an effective low-cost substitute material for activated carbon for removal of chlorophenols from wastewater.     

Physical and chemical regeneration of zeolitic adsorbents for dye removal in wastewater treatment

Natural zeolite and synthetic zeolite, MCM-22, were employed as effective adsorbents for a basic dye, methylene blue, removal from wastewater. Two methods, Fenton oxidation and high temperature combustion, have been used for regeneration of used materials. It is found that MCM-22 exhibits equilibrium adsorption at 1.7 x 10(-4) mol g(-1), much higher than the adsorption of natural zeolite (5 x 10(-5) mol g(-1)) at initial dye concentration of 2.7 x 10(-5)M and 30 degrees C. Solution pH will affect the adsorption behaviour of MCM-22. Higher solution pH results in higher adsorption capacity. The regenerated adsorbents show different capacity depending on regeneration technique. Physical regeneration by high temperature combustion will be better than chemical regeneration using Fenton oxidation in producing effective adsorbents. Regeneration of MCM-22 by high temperature treatment can make the adsorbent exhibit comparable or superior adsorption capacity as compared to the fresh sample depending on the temperature and time. The optimal temperature and time will be 540 degrees C and 1h. The Fenton oxidation will recover 60% adsorption capacity. For natural zeolite, regeneration can not fully recover the adsorption capacity with the two techniques and the regenerated natural zeolites by the two techniques are similar, showing 60% adsorption capacity of fresh sample. Kinetic studies indicate that the adsorption follows pseudo-second-order kinetics.     

Natural organic matter (NOM) in roof runoff and its impact on the Fe0 treatment system of dissolved metals

The present work investigates the impacts and mechanisms associated with natural organic matter (NOM) in the Fe0 treatment system of Cu2+ and Zn2+ under roof runoff conditions. The NOM in runoff waters was characterized using XAD-4/8 adsorption resins, copper complexation, acidic capacity and liquid chromatography with online carbon detection. Batch kinetic experiments and flow-through configurations were performed and the results of metal removal were elucidated taking into account the characteristics of NOM. Based on the findings, it is shown that NOM influences the removal of metals through several complex pathways. At an un-favored condition for adsorption of metals, i.e., on iron corrosion products, at pH相似文献