用开管法快速测定废水的COD

介绍了用硫酸锰代替硫酸银作催化剂快速开管测定废水COD的方法．最佳测定条件为：消解温度170℃,消解时间12min,酸度11mol／L,催化剂(硫酸锰)用量10g／L。该方法使试样的消解时间由标准法的2h缩短到12min,同时用硫酸锰代替价格昂贵的硫酸银可大大降低分析成本,而准确度和精密度与用硫酸银作催化剂的开管法基本相同,COD测定下限为65mg／L。该方法可同时消解多个试样．适用于大批量水样的测定。     

锌冶炼烟气制酸废水中汞的测定

采用冷原子吸收光度法测定经石灰乳和铁盐处理后的锌冶炼烟气制酸废水中汞的浓度时,可按废水中汞浓度与其pH的关系,从试样pH的高低大致估计其汞浓度范围,由此确定其稀释倍数和取样量。试样用KBrO3-KBr消解法消解,用直接法稀释,这样可以减少操作步骤、缩短测定周期、减少样品中汞的损失、提高监测结果的可靠性和准确性,同时可减少人力、物力浪费,降低监测成本。     

COD快速测定法

以用时30min的半微量密闭微波消解法取代COD国标测定中的重铬酸钾回流法,改进后的方法精密度小于5．15％,准确度达到102％,COD测定下限为51mg／L。该法节省时间、取样量少、成本低,适用于大批量水样的快速测定。     

电感耦合等离子体发射光谱法测定石化废水中的重金属

建立了硝酸加热消解后采用电感耦合等离子体发射光谱(ICP-OES)测定石化废水中重金属(As,Cd,Cr,Cu,Zn,Pb,Mn)的方法,优化了仪器工作参数,得到了线性回归方程,并对该方法进行了评价。优化后的仪器工作参数为射频功率1 150 W、雾化器流量0.70 L/min、辅助气流量0.50 L/min。各重金属元素回归方程的相关系数均在0.999 9以上,检出限为0.000 18~0.007 00 mg/L,相对标准偏差为0.1%~2.0%,加标回收率为96.3%~102.2%。该方法具有线性关系好、检出限低、精密度和准确度高、分析速度快等优点。     

生物絮凝法与化学絮凝法处理洗毛废水的比较

分别采用生物絮凝法和化学絮凝法处理300 mL COD为20 000 mg/L、SS为4 000 mg/L的洗毛废水,最佳生物絮凝条件:生物絮凝剂加入量为5 mL,反应温度为30℃,先以120 r/min搅拌5 min、再以60 r/min搅拌35 min,洗毛废水pH为9.0.COD去除率达92%.最佳化学絮凝条件:化学絮凝剂加入量为30 mL,反应温度为40℃,先以120 r/min搅拌5 min、再以60 r/min搅拌25 min,洗毛废水pH为5.0.COD去除率达93%.生物絮凝剂和化学絮凝剂对洗毛废水的絮凝效果接近,但生物絮凝剂的加入量比化学絮凝剂少很多.     

用次氯酸钠法处理选矿废水

采用次氯酸钠法处理铅锌硫化矿选矿废水,考察了废水初始pH、NaClO加入量及反应时间对选矿废水COD去除率的影响。在废水pH为4、NaClO加入量为100g/L、反应时间为30min的条件下,选矿废水的COD去除率可达到98．3％;当pH为11、反应时间为10min、NaClO加入量为1g/L时,选矿废水的COD去除率为39．4％。     

过氧化氢-亚铁盐氧化法对染料废水的脱色处理

染料废水具有成份复杂、色度高、水量少、大多数污染物为难降解的有机化合物等特点。采用传统的生化处理法很难使其达标排放,特别是脱色问题是染料废水处理的难题之一。通常采用化学混凝法和气浮法进行脱色处理,这对不溶性的染料,如分散染料、硫化染料和还原性染料等有良好的脱色效果,而对水溶性染料,如活性染料、直接     

微波消解法测定水中总氮

总氮是衡量水质的重要指标之一。目前,总氮的标准测定方法是过硫酸钾氧化－紫外分光光度法。该法需要进行高温高压消解,不但消解过程耗时较长,而且操作比较繁琐。微波消解技术是近年来发展起来的新的消解方法。本法是用微波炉对水样进行消解,可缩短消解时间。本法与标准方法相比,总氮的测定结果相近。取总氮浓度已知的水样,分别在２～１５ｍｉｎ内进行微波消解试验,确定消解效果与时间的关系。结果表明,采用微波消解５ｍｉｎ即可消解完全。为确保各种水样消解彻底,本试验选择的消解时间为１０ｍｉｎ。取水样２份,分别进行６次平行…     

电力系统常用油品中磨损金属测定方法的研究

采用干、湿两种消解方法。进行了电力系统常用油品的消解方法研究，对消解后试液采用ICP／AES无机进样系统进行测定。通过对测定结果的统计、处理和汇总，以及方法精密度和准确度验证，最终得出了用直接燃烧灰化法代替ASTMD5708标准中的湿法消解来进行样品消解浓缩，使整个操作更为简便、省时。     

导流电解法处理含酚废水的研究

阐述了电解法处理废水的基本原理。通过试验确定了用该法处理含酚废水的最佳工艺条件,出水的酚浓度、pH均达到国家排放标准。该法工艺过程简单,处理效果好,无二次污染。经济分析结果表明,该法处理含酚废水的费用低于传统的电解法。     

The behaviour of selected rare-earth elements during the conversion of phosphogypsum to calcium sulphide and residue

Phosphogypsum (PG) is a large hazardous waste from fertiliser and phosphoric acid industries from which useful products including rare-earth elements (REEs) can be recovered depending on the treatment process. Its conversion to calcium sulphide (CaS) which was achieved at 95% followed by the formation of S, CaCO₃ and residue is one of the plausible treatment processes leading to economic and environmental benefits. This study aimed at monitoring selected REEs behaviour during the conversion of (PG) to (CaS). The concentrations of REEs in the raw PG, the produced CaS and the obtained residue were determined after digestion (microwave and traditional acid leaching) using ICP-OES. The effect of CO₂ and H₂S used in the process of forming CaCO₃ and S from PG on the concentrations of REEs was also investigated. Microwave digestion proved to be more effective than traditional acid leaching in the recovery of REEs. Microwave digestion using 3 mL HNO₃ + 1 mL HCl was more effective than 1 mL HNO₃ + 3 mL in REEs recovery. CaS contained the highest amount of Ce, Pr, Nd, Sm, Eu, Gd, Dy, Ho, Er, La and Y with values of 2646, 476, 2255, 320, 60.5, 376, 79.8, 1.24, 476, 1185 and 318 µg/g respectively. Based on these findings, the residue could be further processed to recover REEs despite less than 40% decrease in concentration for the majority of REEs observed due to the use of H₂S and CO₂. CO₂ was found to be more suitable as fewer REEs were leached as compared to H₂S. All things considered, the obtained residue could be a good secondary source of REEs as it is easier to leach, retained good amount of REEs and lesser impurities.

     

BMP tests of source selected OFMSW to evaluate anaerobic codigestion with sewage sludge

The aim of this study is to characterize different types of source selected organic fraction of municipal solid waste (SS-OFMSW) in order to optimize the upgrade of a sewage sludge anaerobic digestion unit by codigestion. Various SS-OFMSW samples were collected from canteens, supermarkets, restaurants, households, fruit–vegetable markets and bakery shops. The substrates characterization was carried out getting traditional chemical–physical parameters, performing elemental analysis and measuring fundamental anaerobic digestion macromolecular compounds such as carbohydrates, proteins, lipids and volatile fatty acids. Biochemical methane potential (BMP) tests were conducted at mesophilic temperature both on single substrates and in codigestion regime with different substrates mixing ratios. The maximum methane yield was observed for restaurant (675 NmlCH₄/gVS) and canteens organic wastes (571 and 645 NmlCH₄/gVS). The best codigestion BMP test has highlighted an increase of 47% in methane production respect sewage sludge digestion.     

硅藻土强化混凝处理线路板含络合铜废水

采用硅藻土对聚合硫酸铁（PFS）、聚合氯化铝（PAC）的混凝能力进行强化,并用于线路板含络合铜废水中铜的去除。考察了硅藻土加入量、混凝剂加入量、pH、快速搅拌速率和沉淀时间等因素对除铜效果的影响,并与目前常用的硫化钠破络方法进行了对比。实验结果表明：硅藻土强化混凝的除铜效果明显好于单独投加PAC或PFS;PFS-硅藻土除铜效果好于PAC-硅藻土;在pH为8.0~9.0、硅藻土加入量为120 mg/L、PFS加入量为60 mg/L、快速搅拌速率为250 r/min的条件下,沉淀40 min后可使出水铜质量浓度低于0.30 mg/L,比传统破络工艺出水水质更稳定,成本更低。     

Impacts of microwave pretreatments on the semi-continuous anaerobic digestion of dairy waste activated sludge

Microwave (MW) irradiation is one of the new and possible methods used for pretreating the sludge. Following its use in different fields, this MW irradiation method has proved to be more appropriate in the field of environmental research. In this paper, we focused on the effects of MW irradiation at different intensities on solubilization, biodegradation and anaerobic digestion of sludge from the dairy sludge. The changes in the soluble fractions of the organic matter, the biogas yield, the methane content in the biogas were used as control parameters for evaluating the efficiency of the MW pretreatment. Additionally, the energetic efficiency was also examined. In terms of an energetic aspect, the most economical pretreatment of sludge was at 70% intensity for 12 min irradiation time. At this, COD solubilization, SS reduction and biogas production were found to be 18.6%, 14% and 35% higher than the control, respectively. Not only the increase in biogas production was investigated, excluding protein and carbohydrate hydrolysis was also performed successfully by this microwave pretreatment even at low irradiation energy input. Also, experiments were carried out in semi continuous anaerobic digesters, with 3.5 L working volume. Combining microwave pretreatment with anaerobic digestion led to 67%, 64% and 57% of SS reduction, VS reduction and biogas production higher than the control, respectively.     

粉煤灰两步水热法制备人工沸石

以粉煤灰为原料,采用两步水热法制备人工沸石。SEM、XRD、X射线荧光光谱分析结果表明:制得的人工沸石纯度较高,主要为Na-A型沸石和少量13X型沸石,主要化学成分为SiO2和Al2O3。说明采用两步法制备人工沸石克服了传统水热法杂质含量高的缺陷。采用人工沸石处理初始Mn2+质量浓度为50.00mg/L的模拟含锰废水,吸附125min后,Mn2+去除率达98.19%,模拟废水中剩余Mn2+质量浓度为0.90mg/L。     

The first commercial supercritical water oxidation sludge processing plant

Final disposal of sludge continues to be one of the more pressing problems for the wastewater treatment industry. Present regulations for municipal sludge have favored beneficial use, primarily in land application. However, several agencies and entities have warned of potential health risks associated with these methods. Hydrothermal oxidation provides an alternative method that addresses the health concerns associated with sludge disposal by completely converting all organic matter in the sludge to carbon dioxide, water, and other innocuous materials. A hydrothermal oxidation system using HydroProcessing, L.L.C.'s HydroSolids process has been installed at Harlingen, Texas to process up to 9.8 dry tons per day of sludge. Based on a literature review, this system is the largest hydrothermal oxidation system in the world, and the only one built specifically to process a sludge. Start up of Unit 1 of two units of the HTO system began in April 2001. Early results have indicated COD conversion rates in excess of 99.9%. Harlingen Waterworks System estimates that the HydroSolids system will cost less than other alternatives such as autothermal thermophilic aerobic digestion and more traditional forms of digestion that still require dewatering and final disposal. The Waterworks intends to generate income from the sale of energy in the form of hot water and the use of carbon dioxide from the HydroSolids process for neutralization of high pH industrial effluent. The Waterworks also expects to generate income from the treatment of septage and grease trap wastes.     

Effects of plastics in anaerobic digestion of urban solid wastes

Anaerobic digestion is a possible method for treating urban solid wastes. This pilot plant study was undertaken to ascertain the effect of plastic refuse on the anaerobic digestion process of municipal solid wastes. The air-blown polyethylene film present in the air classified light fraction of solid waste from Pompono Beach, Florida, U.S.A. was removed by visual separation. Control digesters operating on this substrate, produced more gas than test digesters to which the plastic scraps had been returned.     

Evaluating the biogas potential of the dry fraction from pretreatment of food waste from households

At the waste handling company NSR, Helsingborg, Sweden, the food waste fraction of source separated municipal solid waste is pretreated to obtain a liquid fraction, which is used for biogas production, and a dry fraction, which is at present incinerated. This pretreatment and separation is performed to remove impurities, however also some of the organic material is removed. The possibility of realising the methane potential of the dry fraction through batch-wise dry anaerobic digestion was investigated. The anaerobic digestion technique used was a two-stage process consisting of a static leach bed reactor and a methane reactor. Treatment of the dry fraction alone and in a mixture with structural material was tested to investigate the effect on the porosity of the leach bed. A tracer experiment was carried out to investigate the liquid flow through the leach beds, and this method proved useful in demonstrating a more homogenous flow through the leach bed when structural material was added. Addition of structural material to the dry fraction was needed to achieve a functional digestion process. A methane yield of 98 m³/ton was obtained from the dry fraction mixed with structural material after 76 days of digestion. This was in the same range as obtained in the laboratory scale biochemical methane potential test, showing that it was possible to extract the organic content in the dry fraction in this type of dry digestion system for the production of methane.     

微波消解-流动注射分光光度法测定总氮和总磷

以碱性过硫酸钾溶液为消解液,采用微波消解-流动注射分光光度法测定水中总氮和总磷。在碱性过硫酸钾溶液中氢氧化钠质量浓度为9.6g/L、微波功率为320W、消解管长度为16m的条件下,总氮和总磷的检出限分别为0.040m g/L和0.020mg/L,线性范围分别为0.040～3.500mg/L和0.020～2.500mg/L,相对标准偏差分别为1.6%和1.0%。微波消解-流动注射分光光度法应用于河水、湖水、化工废水等实际水样中总氮和总磷的测定,加标回收率分别为95.7%～98.1%和97.2%～102.2%。     

活性炭纤维负载TiO2催化剂的制备及其电催化性能

采用溶胶-凝胶法制备了活性炭纤维负载TiO₂催化剂（TiO₂/ACF）,并通过SEM和XRD等手段对TiO₂/ACF进行了表征。以邻苯二甲酸二甲酯（DMP）为目标降解物,考察了催化材料的电催化活性。实验结果表明：在反应温度为25 ℃、初始DMP质量浓度为100.0 mg/L、电解质Na₂SO₄质量浓度为100 mg/L、电流密度为62.5 mA/cm²、电极板间距为4 cm的条件下,经过40 min的降解,DMP质量浓度为1.8 mg/L,DMP去除率为98.2%;TiO₂/ACF在反应过程中可以原位再生,经6次重复使用后仍保持很高的催化活性,对DMP的去除率仍达90%以上。