无机稳定剂处理重金属污染土壤

以重金属污染土壤为研究对象,比较了铁屑、蒙脱石、碳酸钙和羟基磷灰石4种稳定剂对土壤中Pb,Zn,Cd,Cu 4种重金属的稳定效果。实验结果表明,4种稳定剂稳定效率的大小顺序为：羟基磷灰石﹥碳酸钙﹥蒙脱石﹥铁屑。当稳定剂质量分数为10%时,羟基磷灰石、碳酸钙、蒙脱石和铁屑对Pb,Zn,Cd,Cu 4种重金属的平均稳定效率分别为99.63%,98.53%,97.15%,86.95 %。未加稳定剂时,土壤中的Pb以残渣态为主,Zn以残渣态和可交换态为主,Cd以残渣态为主,Cu以残渣态和可交换态为主;加入稳定剂后,土壤中4种金属可交换态的所占比例（简称占比）均显著降低,还原态的占比明显增大,残渣态的占比略有增大,氧化态的占比基本保持不变。     

四氮唑废水处理工艺设计

高浓度、高盐分的四氮唑生产废水通过三效蒸发浓缩,馏出液经铁炭氧微电解和混凝预处理,再采用水解酸化一接触氧化一反应二沉主体组合工艺进行处理。研究了该工艺所需构筑物和设备的设计与选型。该工艺在正常运行条件下,处理后出水pH6～9,COD 302mg／L,BOD5 108mg／L,SS30mg／L,色度36倍,水质达到GB8978--1996（污水综合排放标准》三级标准。     

Urban Metal Flows – A Case Study of Stockholm. Review and Conclusions

Metals have rapidly accumulated in the anthroposphere, especiallyin urban areas, indicating possible environmental and resource problems. Here, Stockholm City was chosen for a case study of urban metal flows, i.e. metal inflow to, metals in the stock of,and metal outflow from the anthroposphere to the biosphere. Themetal stock of Stockholm is large and still growing. The large amounts of metals in the solid waste fraction totally dominatethe outflow from the city. For major parts of the stock, the emissions from goods in use are negligible. There are, however,goods applications corresponding to significant emissions: e.g. the traffic sector (Cu, Zn, Cr, Ni, Pb), the tapwater system (Cu), roofs/fronts or other metal surfaces (Cu, Zn). Today's known metal flows from the anthroposphere of Stockholm to the biosphere and sewage sludge are quantitatively dominated by Zn(34 ton y^-1) and Cu (14 ton y^-1). Historical and present emissions have resulted in high metal concentrations insediments (especially Cd, Hg and Pb, but also Cu and Zn), groundwater (Cu, Hg) and in soils (Hg, Cu, Pb). At present theannual median concentrations are below the Swedish limits for metals in sewage sludge, even if the safety margins aresmall for Cd, Hg and to some extent Cu. The flows of Cu and Zn to Stockholm soils are high with a significant accumulationindicating an environmental impact in a longer time perspective.High levels of metals in surface sediments in the waterenvironments reflects an ongoing input where these metals aretransported from known (Cu, Zn) and or partly unknown (Cd, Hg, Pb) sources. In future urban areas, monitoring of metal flows must be performed both in the anthroposphere and the biospherein order to have a pro active approach to urban environmentalproblems and to get prompt answers to measures taken.     

Bioassessment of silvicultural impacts in streams and wetlands of the Eastern United States

Bioassessment is a useful tool to determine the impact of logging practices on the biological integrity of streams and wetlands. Measuring biota directly has an intuitive appeal for impact assessment, and biota can be superior indicators to physical or chemical characteristics because they can reflect cumulative impacts over time. Logging can affect stream and wetland biota by increasing sedimentation rates, altering hydrologic, thermal, and chemical regimes, and changing the base of food webs. Biotic impacts of logging on streams compared to wetlands probably differ, and in this paper we review some of those differences. In streams, invertebrates, fishes, amphibians, algae, and macrophytes have been used as indicators of logging impacts. In wetlands, bioassessment is just beginning to be used, and plants and birds are the most promising indicator taxa. Various best management practices (BMPs) have been developed to reduce the impacts of logging on stream and wetland biota, and we review quantitative studies that have evaluated the efficacy of some of these techniques in streams and wetlands in the eastern United States. Remarkably few studies that address the overall efficacy of BMPs in limiting biotic changes in streams and wetlands after BMP implementation have been published in scientific journals, although some work exists in reports or is unpublished. We review these works, and compile conclusions about BMP efficacy for biota from this body of research.     

Two-stage thermal gasification of polyolefins

Plastic pellets of polyethylene (PE), polypropylene (PP), and polystyrene (PS) were gasified in a two-stage thermal degradation process. The first stage is the conversion of polyolefins to distilled oils using a melting vessel. In the second stage, the oils from the first stage are gasified using a tubular reactor. The distilled oil yields of PE, PP, and PS in the first stage were 84, 89, 92 wt%, respectively, each at 470°C. The total gas yields of PE, PP, and PS in the second stage were 80, 74, and 6.2 wt%, respectively, each at 800°C. The main components of the product gas for PE and PP were methane and olefins such as ethene and propene. Some aromatic oils, including benzene, toluene, and xylene, were also produced as by-products. The amount of carbonaceous residue, or coke, was very low (less than 1 wt%). By dividing the process into two stages, the coking rate was considerably reduced compared with direct gasification of the polyolefins. Received: July 19, 2000 / Accepted: September 17, 2000     

我国磷石膏处置现状及绿色发展对策

磷石膏的大量堆存不仅占用土地、浪费资源,存在巨大的环境和安全风险,更与我国无废城市发展理念相违背.本文系统梳理了近年来我国磷石膏产排现状、资源化利用现状和资源化利用途径.分析了磷石膏资源化所面临的问题和挑战,主要包括政策支持不配套、标准体系不完善、技术支撑不足和产品市场竞争力弱等.提出磷石膏绿色发展应从政策扶持、技术突...     

Forestry best management practices for timber harvesting and site preparation in the eastern United States: An overview of water quality and productivity research during the past 20 years (1982–2002)

Forestry Best Management Practices (BMPs) were developed to protect water quality. In the eastern US, those BMPs were often expanded to include maintenance of site productivity. Generally, BMPs recommend the use of pre-harvest planning and careful design for construction of roads and other activities that expose bare soil, minimizing trafficking and areas of bare soil, maintaining streamside management zones, ensuring rapid revegetation following harvesting, minimizing soil disturbance, and ameliorating severe trafficking with site preparation. This review of peer-reviewed research from the past 20 years examined the effects of forest harvesting and site preparation on water quality and site productivity in the eastern US. The review was subdivided into areas having relatively similar physiography and land management (New England, Lake States, Appalachian Plateau, Ridge and Valley, Blue Ridge, Piedmont, Atlantic Coastal Plain, Gulf Coastal Plain, and Ouachitas-Ozarks). In general, data from steeper physiographic regions indicated that forest harvesting and site preparation can increase erosion, sediment and nutrient losses to streams. However, the quantities introduced into streams tended to be relatively low, generally below the values that are considered acceptable for alternative land uses. Also most research indicated that water quality recovers within two to five years following forest operation disturbances, particularly if BMPs are employed. Research from the less mountainous and often more poorly drained Lake States and Coastal Plain regions indicated that soil compaction and rutting may or may not cause site productivity effects, depending on soil types, natural ameliorative properties and site preparation. Overall, the research supports the forestry BMPs recommended in the eastern states.     

Recovery of Acidified Lakes: Lessons From Sudbury, Ontario, Canada

Over 7,000 lakes around Sudbury, Ontario, Canada were acidified by S deposition associated with emissions from the Sudbury metal smelters and more distant S sources. Air pollution controls have led to widespread changes in damaged Sudbury lakes, including increased pH and decreased concentrations of SO₄, metals and base cations. While chemical improvements have often been substantial, many lakes are still acidified, although water quality recovery is continuing. Biological recovery has been observed in some lakes among various groups of organisms including fish, zooplankton, phytoplankton and zoobenthos. Generally, however, biological recovery is still at an early stage. Lakes around Sudbury are also showing that the recovery of acid-damaged lakes is closely linked to the effects of other major environmental stressors such as climate change, base cation depletion and UV-B irradiance. Future studies of the recovery of acid-damaged lakes around Sudbury, and in other regions, will need to consider the interactions of these and other stressors.     

煤矸石中铅、铬、镉的溶出性能

以滕南煤田某煤矿风化煤矸石为研究对象,应用主成分分析法分析了煤矸石粒径对Pb,Cr,Cd溶出浓度的影响,应用回归分析法分析了浸溶时间与Pb,Cr,Cd溶出浓度的关系特征。实验结果表明：模拟湿地浸溶条件下,煤矸石中Pb,Cd,Cr溶出浓度均超出或接近Ⅲ类水体水质标准,对水环境存在污染风险;煤矸石粒径对Pb,Cd,Cr溶出浓度存在影响,粒径越小则Pb、Cr、Cd溶出浓度越大,粒径小于8.0 cm的煤矸石浸溶贡献较大。建立了表征Pb,Cr,Cd溶出浓度与浸溶时间对数（以10为底）关系的一元三次多项式回归方程,经检验均具有显著性。     

循环经济模式构建探讨（续前）

（接上期）4循环经济模式的实践4.1国外循环经济模式解析由于国情不同、发展阶段不同、科技文化发展水平和传统不同,以及制度、体制、机制不同,所以各国在循环经济认识与实践方面有较大差异。     

Characteristics of air pollution in Beijing during sand-dust storm periods

In the Beijing area, March and April have the highest frequency of sand-dust weather. Floating dust, blowing sand, and dust storms, primarily from Mongolia, account for 71%, 20%, and 9% of sand-dust weather, respectively. Ambient air monitoring and analysis of recent meteorological data from Beijing sand-dust storm periods revealed that PM₁₀ mass concentrations during dust storm events remained at 1500 μg m⁻³, which is five to ten times higher than during non-dust storm periods, for fourteen hours on both April 6 and 25, 2000. During the same period, the concentrations in urban areas were comparable to those in suburban areas, while the concentrations of gaseous pollutants, such as SO₂, NO _x , NO₂, and O₃, remained at low levels, owing to strong winds. Furthermore, during sand-dust storm periods, aerosols were created that consisted not only of many coarse particles, but also of a large quantity of fine particles. The PM_2.5 concentration was approximately 230 μg m⁻³, accounting for 28% of the total PM₁₀ mass concentration. Crustal elements accounted for 60–70% of the chemical composition of PM_2.5, and sulfate and nitrate for much less, unlike the chemical composition of PM_2.5 on pollution days, which was primarily composed of sulfates, nitrates, and organic material. Although the very large particle specific surface area provided by dust storms would normally be conducive to heterogeneous reactions, the conversion rate from SO₂ to SO₄ ²⁻ was very low, because the relative humidity, less than 30%, was not high enough.     

催化臭氧氧化—好氧生化—膜分离组合工艺处理砷化镓生产废水的工程应用

为了解决砷化镓生产废水含有磷酸盐、氟化物、砷化物以及难沉降亚微米级悬浮物的处理难点,首先采用催化臭氧氧化—好氧生化深度预处理废水,再采用RO膜分离工艺进行处理。结果表明：催化臭氧氧化法使废水中亚微米级悬浮物脱稳,有利于悬浮物的混凝沉降,并优化了膜分离阶段的分离环境,可延长膜使用寿命,降低运行成本;经过膜分离后,出水砷质量浓度为0.01 mg/L,氟质量浓度为1.0 mg/L,COD、TP、TN和ρ（NH₃-N）为10,0.01,0.50,0.50 mg/L,均达到《地表水环境质量标准》（GB3838—2002）Ⅲ类水质标准。     

Long-Term Observation of Asian Dust in Changchun and Kagoshima

Monitoring of Asian dust at two stations in Changchun, Jilin Province in northeast China, and Kagoshima, southwest Japan, is discussed. In Changchun, interval records were made with digital and video cameras from 18 March 2003. In Kagoshima, a web camera system to monitor volcanic clouds has been working since December 2000, which also provides data for studies of dust. A heavy dust episode on 11 November 2002, affecting both stations, was detected using 11 and 12 μm channels of NOAA/AVHRR. We observed dust in Changchun on 26 March, 7, 14–16 April, 1–2, 8, 10, 19 May, 8, 23 June, and 12 July in 2003. The observed images corresponded well to NOAA/AVHRR imagery and with 8.6, 11 and 12 μm Terra/MODIS results, although conditions were too cloudy for satellite verification in some cases.     

Treatment-oriented characterization of dry scrubber residue from municipal solid waste incineration

 Dry scrubber residue from municipal solid waste incineration (MSWI) was characterized to identify critical inorganic pollutants and to suggest a conceptual treatment method. The key methods used were thermal analysis, including thermogravimetry (TG) and differential thermal analysis (DTA), pH_stat titration, qualitative X-ray diffraction (XRD), scanning electron microscopy (SEM), chemical equilibrium calculations, and statistics such as error propagation, principal component analysis (PCA), and empirical modeling based on factorial designs. Based on EU directives, the major inorganic pollutants Cd, Cr, Pb, and Zn were found. In addition, the pH was too high. With dry scrubber residue stabilization in mind, the impact of carbonation and hydration was assessed and judged to be encouraging. In particular, chemical equilibrium calculations showed that carbonation has considerable potential to lower the pH and the availability of Pb, Zn, and Cr. The impact of carbonation on the mobility of Cd was found to be small. During carbonation, a metal-trapping calcium aluminosilicate hydrate (C–A–S–H) phase is also formed. Both processes together have the potential to lead to a robust, reliable, and reasonable stabilization method for dry scrubber residue. However, to control these processes, the decisive factors need to be identified and their effects need to be quantified. Ca, Cl, Na, and K might be abundant components which would be mobile even after stabilization. Received: September 11, 2001 / Accepted: December 6, 2001     

环氧丙烷生产中副产1,2-二氯丙烷的综合利用

介绍了近年来国内外环氧丙烷生产废液的综合利用情况。环氧丙烷生产中的主要副产物1，2-二氯丙烷，可直接用来制备农药D-D混剂和沥青涂料，直接用作油漆和涂料溶剂以及脱脂溶剂，还可以用于制备丙烯、氯丙烯、环氧丙烷和丙二醇等重要化工产品。同时指出了其综合利用的应用前景和发展方向。     

生物炭修复Cd,Pb污染土壤的研究进展

随着矿产开采、冶炼等工业活动以及污水灌溉、施用污泥和劣质化肥等农业活动的进行,Cd,Pb等有害重金属不断进入农业环境中,对农田、菜地等造成污染。生物炭作为重要的土壤改良剂,在对Cd,Pb污染土壤的修复中表现出巨大的潜力。从生物炭的特性及制备、修复效果及其影响因素、修复机理等方面,对近年来国内外有关生物炭修复Cd,Pb污染土壤的研究成果和现状进行了总结,并对生物炭修复Cd,Pb污染土壤的发展前景和未来研究方向进行了展望。     

吸附-Fenton氧化-絮凝法处理对硝基苯胺生产废水

采用吸附-Fenton氧化-絮凝法处理对硝基苯胺生产废水(简称废水),研究了吸附剂、脱附温度、絮凝剂等因素对处理效果的影响.经实验确定的最佳工艺条件为:DM301大孔树脂加入量5.0 g/L,吸附时间20 h,Fenton氧化pH 3.0,H_20_2加入量0.3 moL/L,m(Fe):m(H_20_2)=6,絮凝阴离子型聚丙烯酰胺加入量20 mg/L.在此条件下对COD为2 780 mg/L、色度为185倍和pH为12.2的废水进行处理,出水的COD、色度和pH分别为169 mg/L、10倍和6.5,COD去除率和色度去除率分别达到93.9%和94.5%.DM301树脂在10～25次重复使用后对硝基苯胺的平均总去除率为47.7%,对硝基苯胺的平均回收率为37.9%.     

Modelling Change in Ground Vegetation Response to Acid and Nitrogen Pollution, Climate Change and Forest Management at in Sweden 1500–2100 a.d.

The ForSAFE model, designed for modelling biogeochemical cycles (water, acidity, base cation, nitrogen and carbon) in terrestrial ecosystems, was modified with a vegetation response module (VEG), incorporating the effects of: nitrogen pollution, acidification, soil moisture, temperature, wind chill exposure, light and shading by trees, grazing by animals, competition between plants, above ground for light and below ground for water and nutrients. The model calculates the response of number ground vegetation plant groups. The integrated model was tested and validated at integrated level II forest monitoring sites across Sweden, four have been shown here, and used to assess the effect of acidification and nitrogen pollution in relation to factors such as climate change, forest management and changing grazing pressure. The response functions have been derived from single-factor experiments and integrated through the model structure for use on whole systems. The tests with the model suggest that the ground vegetation composition is reasonably well predicted, that much research remains before the model is fully tested and operational, and that the model may serve as a tool for assessing impacts of climate change, acid rain and forest management on plant biodiversity in forested areas.     

赤泥中重金属元素的浸出性与结合形态

采用等离子体质谱仪分析了拜耳法赤泥(BRM)和烧结法赤泥(SRM)中Cr,Ni,Cu,Zn,As,Cd,Cs,Pb等8种重金属元素的含量。采用逐级提取的方法分析了BRM和SRM中8种重金属元素的浸出情况和形态分布差异。实验结果表明:SRM中水溶态As的质量浓度达到17.3μg/L,BRM和SRM中可交换态Cr的质量浓度均在2 300μg/L以上,对水环境可能存在潜在危害;两种赤泥中不同形态重金属的浸出率有较大差异,SRM中Ni和BRM中Zn的总浸出率分别在60%和50%以上。     

Transformations of nitrogen at the interface between the topsoil and an impervious clay subsoil

Much work has been done on gaseous emissions and leaching of nitrogenous compounds from whole soil profiles and also from soil surface measurements which are assumed to be mainly due to topsoil activity. In soils with an impervious clay subsoil, the boundary between the topsoil and subsoil may provide an interface for microbial activity, including N transformations. In this study, we investigated movement and transformations of two reactive N species (nitrate and urea) at the subsoil interface using a series of replicate, intact soil blocks, under two contrasting watering regimes. We measured fluxes in both liquid and gaseous phases and demonstrated that nitrate reaching the subsoil interface does not necessarily leach into water systems, but may denitrify immediately and could, therefore, add to atmospheric pollution through N₂O production. On the other hand, ammonium reaching the subsoil interface either directly, or after mineralization, appears to be more mobile than expected and has the potential to pollute watercourses.