Tylosin Sorption to Silty Clay Loam Soils,Swine Manure,and Sand

The objectives of this study were to assess sorption and desorption of tylosin, a macrolide antimicrobial chemical used in swine, cattle, and poultry production, in three silty clay loam soils of South Dakota and compare soil sorption to sand and manure sorption. The silty clay loam soils, from a toposequence in eastern South Dakota, standardized sand samples, and swine manure were used in 24-h batch sorption studies with tylosin concentrations ranging from 25 to 232 μ mole/L. Desorption from soil was conducted over a four-day period. Partition coefficients, based on the Freundlich isotherm (K _f ) or K _d values, were calculated. K _f values for the silty clay loams were similar, not influenced by landscape position, and averaged 1350 with isotherm slopes ranging from 0.85 to 0.93. K _f values for sand were dependent on solution/sand ratios and pH, ranging from 1.4 to 25.1. K _d values of manure were dependent on the solution type and ranged from 840 L/kg with urine to about 175 L/kg when sorbed from water. Desorption of tylosin from each soil over the four-day period was < 0.2% of the amount added. The soils' high K _f values and low desorption amounts suggest that once tylosin is in these soils, leaching to lower depths may not occur. However, this does not preclude runoff with soil eroded particles. If tylosin reaches a sand aquifer, through bypass flow or other mechanism(s), movement in the aquifer most likely would occur.     

Adsorption,Desorption, and Mobility of Permethrin in Malaysian Soils

Abstract

The adsorption, desorption, and mobility of permethrin in six tropical soils was determined under laboratory and greenhouse conditions. The six soils were selected from vegetable growing areas in Malaysia. Soil organic matter (OM) was positively correlated (r ² = 0.97) with the adsorption of permethrin. The two soils, namely, Teringkap 1 and Lating series with the highest OM (3.2 and 2.9%) released 32.5 and 30.8% of the adsorbed permethrin after four consecutive repetitions of the desorption process, respectively, compared to approximately 75.4% of the Gunung Berinchang soil with the lowest OM (1.0%) under the same conditions. The mobility of permethrin down the soil column was inversely correlated to the organic matter content of the soil. Permethrin residue penetrated only to the 10–15 cm zone in the Teringkap 1 soil with 3.2% OM but penetrated to a depth of more than 20 cm in the other soils. The Berinchang series soil with the lowest OM (1.0%) yielded leachate with 14.8% permethrin, the highest level in leachates from all the soils tested. Therefore, the possibility for permethrin to contaminate underground water may be greater in the presence of low organic matter content, which subsequently allows a higher percentage of permethrin to move downwards through the soil column.     

Sorption Kinetics of Atrazine and Diuron in Soils from Southern Brazil

Abstract

Sorption kinetics of atrazine and diuron was evaluated in soil samples from a typical landscape in Paraná. Samples were collected (0–20 cm) in a no-tillage area from Mamborê, PR, which has been cultivated under a crop rotation for the last six years. Six sampling points of the slope were selected to represent a wide range of soil chemical and physical properties found in this area. Radiolabeled tracers (¹⁴C-atrazine and ¹⁴C-diuron) were used and the radioactivity was detected by liquid scintillation counting (LSC). Sorption was accomplished for increasing equilibration periods (0.5, 1.5, 3, 6, 12, 24, and 48 h). Kinetics data fitted adequately well to Elovich equation, providing evidences that soil reaction occurs in two distinct stages: a fast, initial one followed by a slower one. During the fast phase, 34–42 and 71–79% of total atrazine and diuron applied were sorbed to soil samples. No important differences were found among combinations of soil and herbicide sorption during the slow phase. The unrealistic conditions under batch experiments should be overestimating sorption in the fast phase and underestimating diffusion in the slow phase. Sorption of both herbicides was positively correlated to organic carbon and clay contents of soils, but atrazine was much less sorbed than diuron, showing its higher potential to contaminate groundwater, specially in sandy, low organic carbon soils.     

Sorption, desorption, and degradation of (4-chloro-2-methylphenoxy)acetic acid in representative soils of the Danubian Lowland, Slovakia

Herbicide leaching through soil into groundwater greatly depends upon sorption-desorption and degradation phenomena. Batch adsorption, desorption and degradation experiments were performed with acidic herbicide MCPA and three soil types collected from their respective soil horizons. MCPA was found to be weakly sorbed by the soils with Freundlich coefficient values ranging from 0.37 to 1.03 mg^1−1/n kg⁻¹ L^1/n. It was shown that MCPA sorption positively correlated with soil organic carbon content, humic and fulvic acid carbon contents, and negatively with soil pH. The importance of soil organic matter in MCPA sorption by soils was also confirmed by performing sorption experiments after soil organic matter removal. MCPA sorption in these treated soils decreased by 37-100% compared to the original soils. A relatively large part of the sorbed MCPA was released from soils into aqueous solution after four successive desorption steps, although some hysteresis occurred during desorption of MCPA from all soils. Both sorption and desorption were depth-dependent, the A soil horizons exhibited higher retention capacity of the herbicide than B or C soil horizons. Generally, MCPA sorption decreased in the presence of phosphate and low molecular weight organic acids. Degradation of MCPA was faster in the A soil horizons than the corresponding B or C soil horizons with half-life values ranging from 4.9 to 9.6 d in topsoils and from 11.6 to 23.4 d in subsoils.     

Two-Compartment Sorption of Phenanthrene on Eight Soils with Various Organic Carbon Contents

Sorption characteristics of phenanthrene (PHE) were studied on eight soils with organic carbon contents spanning over an order of magnitude using phase distribution relationships (PDRs) at 1 h, 48 h, and 720 h contact times. A new algebraic method was employed to describe the sorption characteristics at different time intervals (between 1 h and 48 h, and 1 h and 720 h). It was found that nonlinearity increased with increasing contact time and sorption that occurred in the subsequent time interval following the initial 1 h exhibited stronger isotherm nonlinearity. Sorption coefficients were positively correlated with the organic carbon contents of the soils. Detailed sorption dynamics were also examined on these soils. A two-compartment, first-order model was used to describe the sorption dynamics. The rate constants of the two compartments differed 18–170 times, suggesting the dissimilar sorption behaviors of the mathematically separated compartments. These two compartments were labeled fast and slow sorption compartment according to the rate constants. Calculation showed that the fast compartment accounted for over 80% of the overall sorption at the initial 1 h, while the slow compartment predominated the total sorption in the following 47 h. By combining the discussion of PDRs and sorption dynamics, the contributions of the two compartments to linear and nonlinear sorption were differentiated. The slow sorption compartment made a major contribution to nonlinear sorption and possibly to sequestration of organic pollutants by these soils.     

Modelling of diffusion-limited retardation of contaminants in hydraulically and lithologically nonuniform media

A new reactive transport modelling approach and examples of its application are presented, dealing with the impact of sorption/desorption kinetics on the spreading of solutes, e.g. organic contaminants, in groundwater. Slow sorption/desorption is known from the literature to be strongly responsible for the retardation of organic contaminants. The modelling concept applied in this paper quantifies sorption/desorption kinetics by an intra-particle diffusion approach. According to this idea, solute uptake by or release from the aquifer material is modelled at small scale by a "slow" diffusion process where the diffusion coefficient is reduced as compared to the aqueous diffusion coefficient due to (i) the size and shape of intra-particle pores and (ii) retarded transport of solutes within intra-particle pores governed by a nonlinear sorption isotherm. This process-based concept has the advantage of requiring only measurable model parameters, thus avoiding fitting parameters like first-order rate coefficients.In addition, the approach presented here allows for modelling of slow sorption/desorption in lithologically nonuniform media. Therefore, it accounts for well-known experimental findings indicating that sorptive properties depend on (i) the grain size distribution of the aquifer material and (ii) the lithological composition (e.g. percentage of quartz, sandstone, limestone, etc.) of each grain size fraction. The small-scale physico-chemical model describing sorption/desorption is coupled to a large-scale model of groundwater flow and solute transport. Consequently, hydraulic heterogeneities may also be considered by the overall model. This coupling is regarded as an essential prerequisite for simulating field-scale scenarios which will be addressed by a forthcoming publication.This paper focuses on mathematical model formulation, implementation of the numerical code and lab-scale model applications highlighting the sorption and desorption behavior of an organic contaminant (Phenanthrene) with regard to three lithocomponents exhibiting different sorptive properties. In particular, it is shown that breakthrough curves (BTCs) for lithologically nonuniform media cannot be obtained via simple arithmetic averaging of breakthrough curves for lithologically uniform media. In addition, as no analytical solutions are available for model validation purposes, simulation results are compared to measurements from lab-scale column experiments. The model results indicate that the new code can be regarded as a valuable tool for predicting long-term contaminant uptake or release, which may last for several hundreds of years for some lithocomponents. In particular, breakthrough curves simulated by pure forward modelling reproduce experimental data much better than a calibrated standard first-order kinetics reactive transport model, thus indicating that the new approach is of high quality and may be advantageously used for supporting the design of remediation strategies at contaminated sites where some lithocomponents and/or grain size classes may provide a long-term pollutant source.     

Sorption of organic pollutants by marine sediments: implication for the role of particulate organic matter

The objective of this study was to quantify sorption properties for kerogen/black carbon (BC)-bearing sediments. Single-solute sorption isotherms were measured for five pristine marine sediments using phenanthrene, naphthalene, 1,3,5-trichlorobenzene, and 1,4-dichlorobenzene as the sorbates. The results showed that the sorption isotherms were nonlinear and that the organic carbon normalized single point K_OC values were comparable to those reported in the literature for the purified keorgen and BC, but are much higher than the data reported for HA and kerogen/BC-containing terrestrial soils and sediments. It is likely that koergen and BC associated with these pristine marine sediments may not be encapsulated with humic acids or Fe and Mn oxides and hydroxides as often do in terrestrial soils and sediments. As a result, they may be fully accessible to sorbing molecules, exhibiting higher sorption capacities. The study suggests that competition from background HOCs and reduced accessibility when kerogen and BC are associated with terrestrial sediments may dramatically increase variability of sorption reactivities of geosorbents. Such variability may lead to large uncertainties in the prediction of sorption from the contents of kerogen and/or BC along with TOC.     

Effects of SOM, surfactant and pH on the sorption-desorption and mobility of prometryne in soils

Sorption and desorption of the herbicide prometryne in two types of soil subjected to the changes of pH and soil organic matter and surfactant were investigated. The sorption and desorption isotherms were expressed by the Freundlich equation. Freundlich K_f and n values indicate that soil organic matter was the major factor affecting prometryne behavior in the test soils. We also quantified the prometryne sorption and desorption behavior in soils, which arose from the application of Triton X-100 (TX100), a nonionic surfactant and change in pH. Application of TX100 led to a general decrease in prometryne sorption to the soils and an increase in desorption from the soils when applied in dosages of the critical micella concentration (CMC) 0.5, 1 and 2. At the concentration below the CMC, the non-ionic surfactant showed a tendency to decrease prometryne sorption and desorption. It appeared that TX100 dosages above CMC were required to effectively mobilize prometryne. Results indicate that the maximum prometryne sorption and minimum prometryne desorption in soils were achieved when the solution pH was near its pK_a. Finally, the influence of TX100 on the mobility of prometryne in soils using soil thin-layer chromatography was examined.     

BDE-47 sorption and desorption to soil matrix in single- and binary-solute systems

Three loamy-clay soil samples (LC1-3) with different properties were collected as the geosorbents to preliminarily investigate the sorption and desorption of 2,2′,4,4′-tetrabromodiphenyl ether (BDE-47) in single system and binary system with the presence of decabromodiphenyl ether (BDE-209), which can provide information in order to further understand the sorption mechanisms and evaluate the adsorption sites. A concentration of 10 μg L⁻¹ BDE-209 suppressed the sorption of BDE-47, and the trend became more and more significant with the increase of BDE-47 equilibrium concentration, however, BDE-47 caused no competitive effect on BDE-209 sorption, which was related with the better accessibility of more hydrophobic molecules to adsorption sites. In the binary system, nonlinearity of the BDE-47 sorption isotherms for the three samples changed in different ways, which originated from the varied soil properties. Desorption hysteresis was observed in all cases, which was estimated due to irreversible surface adsorption between sorbent and sorbate. BDE-209 made desorption of BDE-47 more hysteretic from soil samples, which was estimated to be ascribed to the accelerated sorbent state transition and new sites creation caused by BDE-209 sorption.     

Experimental Variability in Characterization of Cyfluthrin Sorption to Soil

To assess the risk of a pesticide to leach to groundwater or to run off to surface water after application, it is necessary to characterize the sorption of the pesticide to soil. For pyrethroids, their hydrophobicity, strong sorption to various materials, and low solubility make it difficult to accurately characterize sorption processes. The objective of this research was to evaluate the variability in cyfluthrin ((RS)-α -cyano-4-fluoro-3-phenoxybenzyl (1RS,3RS;1RS,3SR)-3-(2,2-dichlorovinyl)-2,2-dimethylcyclopropanecarboxylate) sorption to soil as affected by experiment conditions. To minimize cyfluthrin sorption on the walls of glass, silanized-glass, stainless steel, and PTFE centrifuge tubes, cyfluthrin solution was added to aqueous soil slurries or directly to soil, after which it was equilibrated with aqueous solution. Depending on the soil, variation in sorption coefficients, K _oc, obtained using different experimental methodologies with one soil can be comparable to the variation in K _oc values obtained for soils with different physical and chemical properties using one method. K _oc values for cyfluthrin ranged from 56,000 to 300,000 L kg^?1. Sorption methodology needs to be evaluated before sorption coefficients are used in predictive transport models.     

Effect of Pinus radiata derived biochars on soil sorption and desorption of phenanthrene

Biochars are anthropogenic carbonaceous sorbent and their influences on the sorption of environmental contaminants need to be characterized. Here we evaluated the effect of Pinus radiata derived biochars on soil sorption and desorption of phenanthrene. Two biochars separately produced at 350 °C and 700 °C and three soils were tested. Biochar amendment generally enhanced the soil sorption of phenanthrene. The biochar produced at 700 °C generally showed a greater ability at enhancing a soil’s sorption ability than that prepared at 350 °C. The single-step desorption measurement showed an apparent hysteresis in biochar-amended soils. After 28 d equilibration, the sorptive capacity of biochar-amended soil (with an organic carbon content of 0.16%) significantly decreased. This study clearly suggested that biochar application enhanced soil sorption of hydrophobic organic compounds, but the magnitude of enhancement depended on the preparation of biochars, the indigenous soil organic carbon levels, and the contact time between soil and biochar.     

Sorption of imidacloprid and its metabolites on tropical soils

Abstract

The sorption of imidacloprid (l‐[(6‐chloro‐3‐pyridinyl)‐methyl]‐N‐nitro‐2‐imidazolid‐inimine) (IMI) and its metabolites imidacloprid‐urea (l‐[(6‐chloro‐3‐pyridinyl)‐methyl]‐2‐imidazol‐idinone) (IU), imidacloprid‐guanidine (l‐[(6‐chloro‐3‐pyridinyl)‐methyl]‐4,5‐dihydro‐lH‐imidazol‐2‐amine) (IG), and imida‐cloprid‐guanidine‐olefin ( 1 ‐[(6‐chloro‐3‐pyridinyl)methyl]‐lH‐imidazol‐2‐amine) (IGO) was determined on six typical Brazilian soils. Sorption of the chemicals on the soil was characterized using the batch equilibration method. The range and order of sorption (Kd) on the six soils was IG (4.75–134) > IGO (2.87–72.3) > IMI (0.55 ‐16.9) > IU (0.31–9.50). For IMI and IU, Kd was correlated with soil organic carbon (OC) content and CEC, the latter due to the high correlation between OC and cation exchange capacity (CEC) (R²=0.98). For IG and IGO, there was no correlation of sorption to clay, pH, OC or CEC due to the high sorption on all soils. Average Koc values were IU = 170, IMI = 362, IGO = 2433, and IG = 3500. Although Kd and Koc values found were consistently lower than those found in soils developed in non‐tropical climates, imidacloprid and its metabolites were still considered to be slightly mobile to immobile in Brazilian soils.     

Sorption and transport of trichloroethylene in caliche soil

Sorption of TCE to the caliche soil exhibited linear isotherm at the high TCE concentrations (Co = 122-1300 mg L⁻¹) but Freundlich isotherm at the low concentration range (1-122 mg L⁻¹). Sorption strength of the carbonate fraction of the soil was about 100-fold lower than the sorption strength of soil organic matter (SOM) in the caliche soil, indicating weak affinity of TCE for the carbonate fraction of the soil. Desorption of TCE from the caliche soil was initially rapid (7.6 × 10⁻⁴ s⁻¹), then continued at a 100-fold slower rate (7.7 × 10⁻⁶ s⁻¹). Predominant calcium carbonate fraction of the soil (96%) was responsible for the fast desorption of TCE while the SOM fraction (0.97%) controlled the rate-limited desorption of TCE. Transport of TCE in the caliche soil was moderately retarded with respect to the water (R = 1.75-2.95). Flow interruption tests in the column experiments indicated that the rate-limited desorption of TCE controlled the non-ideal transport of TCE in the soil. Modeling studies showed that both linear and non-linear nonequilibrium transport models provided reasonably good match to the TCE breakthrough curves (r² = 0.95-0.98). Non-linear sorption had a negligible impact on both the breakthrough curve shape and the values of sorption kinetics parameters at the high TCE concentration (Co = 1300 mg L⁻¹). However, rate-limited sorption/desorption processes dominated at this concentration. For the low TCE concentration case (110 mg L⁻¹), in addition to the rate-limited sorption/desorption, contribution of the non-linear sorption to the values of sorption kinetics became fairly noticeable.     

Effect of soil and sediment composition on acetochlor sorption and desorption

Background, aim, and scope  Herbicide fate and its transport in soils and sediments greatly depend upon sorption–desorption processes. Quantitative determination of herbicide sorption–desorption is therefore essential for both the understanding of transport and the sorption equilibrium in the soil/sediment–water system; and it is also an important parameter for predicting herbicide fate using mathematical simulation models. The total soil/sediment organic carbon content and its qualitative characteristics are the most important factors affecting sorption–desorption of herbicides in soil or sediment. Since the acetochlor is one of the most frequently used herbicides in Slovakia to control annual grasses and certain annual broad-leaved weeds in maize and potatoes, and posses various negative health effects on human beings, our aim in this study was to investigate acetochlor sorption and desorption in various soil/sediment samples from Slovakia. The main soil/sediment characteristics governing acetochlor sorption–desorption were also identified. Materials and methods  The sorption–desorption of acetochlor, using the batch equilibration method, was studied on eight surface soils, one subsurface soil and five sediments collected from the Laborec River and three water reservoirs. Soils and sediments were characterized by commonly used methods for their total organic carbon content, distribution of humus components, pH, grain-size distribution, and smectite content, and for calcium carbonate content. The effect of soil/sediment characteristics on acetochlor sorption–desorption was examined by simple correlation analysis. Results  Sorption of acetochlor was expressed as the distribution coefficient (K _d). K _d values slightly decreased as the initial acetochlor concentration increased. These values indicated that acetochlor was moderately sorbed by soils and sediments. Highly significant correlations between the K _d values and the organic carbon content were observed at both initial concentrations. However, sorption of acetochlor was most closely correlated to the humic acid carbon, and less to the fulvic acid carbon. The total organic carbon content was found to also significantly influence acetochlor desorption. Discussion  Since the strong linear relationship between the K _d values of acetochlor and the organic carbon content was already released, the corresponding K _oc values were calculated. Considerable variation in the K _oc values suggested that other soil/sediment parameters besides the total soil organic carbon content could be involved in acetochlor sorption. This was revealed by a significant correlation between the K _oc values and the ratio of humic acid carbon to fulvic acid carbon (C_HA/C_FA). Conclusions  When comparing acetochlor sorption in a range of soils and sediments, different K _d values which are strongly correlated to the total organic carbon content were found. Concerning the humus fractions, the humic acid carbon content was strongly correlated to the K _d values, and it is therefore a better predictor of the acetochlor sorption than the total organic carbon content. Variation in the K _oc values was attributed to the differences in distribution of humus components between soils and sediments. Desorption of acetochlor was significantly influenced by total organic carbon content, with a greater organic carbon content reducing desorption. Recommendations and perspectives  This study examined the sorption–desorption processes of acetochlor in soils and sediments. The obtained sorption data are important for qualitative assessment of acetochlor mobility in natural solids, but further studies must be carried out to understand its environmental fate and transport more thoroughly. Although, the total organic carbon content, the humus fractions of the organic matter and the C_HA/C_FA ratio were sufficient predictors of the acetochlor sorption–desorption. Further investigations of the structural and chemical characteristics of humic substances derived from different origins are necessary to more preciously explain differences in acetochlor sorption in the soils and sediments observed in this study.     

Sorption and cosorption of organic contaminant on surfactant-modified soils

Three kinds of soils were modified with the cationic surfactants, hexadecyltrimethylammonium (HDTMA) bromide and tetramethylammonium (TMA) bromide to increase their sorptive capabilities. Sorption of chlorobenzene in simulated groundwater by these soils was investigated. HDTMA-modified soil has a higher ability to sorb chlorobenzene from simulated groundwater than unmodified soil. TMA-modified soil did not show the superiority. HDTMA thus can be used to modify soil to improve its sorption capability. Cosorption of chlorobenzene in simulated groundwater in the absence or presence of nitrobenzene and dichloromethane on HDTMA-modified soil was also investigated. Nitrobenzene facilitated sorption of chlorobenzene on all HDTMA-modified soil. Dichloromethane did not influence the sorption of chlorobenzene by HDTMA-modified soil. The results suggest that HDTMA-modified soil is a highly effective sorbent for chlorobenzene and multiple organic compounds did not impede the uptake of chlorobenzene.     

Dissolved organic carbon from sewage sludge and manure can affect estrogen sorption and mineralization in soils

In this study, effects of sewage sludge and manure borne dissolved organic carbon (DOC) on 17β-estradiol (E2) and 17α-ethinylestradiol (EE2) sorption and mineralization processes were investigated in three agricultural soils. Batch equilibrium techniques and equilibrium dialysis methods were used to determine sorption mechanisms between DOC, estrogens and the soil solid phase. It was found that that the presence of organic waste borne DOC decreased estrogen sorption in soils which seems to be controlled by DOC/estrogen complexes in solution and by exchange processes between organic waste derived and soil borne DOC. Incubation studies performed with ¹⁴C-estrogens showed that DOC addition decreased estrogen mineralization, probably due to reduced bioavailability of estrogens associated with DOC. This increased persistence combined with higher mobility could increase the risk of estrogen transport to ground and surface waters.     

Sorption of polar and nonpolar organic contaminants by oil-contaminated soil

Sorption of nonpolar (phenanthrene and butylate) and polar (atrazine and diuron) organic chemicals to oil-contaminated soil was examined to investigate oil effects on sorption of organic chemicals and to derive oil–water distribution coefficients (K_oil). The resulting oil-contaminated soil–water distribution coefficients (K_d) for phenanthrene demonstrated sorption-enhancing effects at both lower and higher oil concentrations (C_oil) but sorption-reducing (competitive) effects at intermediate C_oil (approximately 1 g kg⁻¹). Rationalization of the different dominant effects was attempted in terms of the relative aliphatic carbon content which determines the accessibility of the aromatic cores to phenanthrene. Little or no competitive effect occurred for butylate because its sorption was dominated by partitioning. For atrazine and diuron, the changes in K_d at C_oil above approximately 1 g kg⁻¹ were negligible, indicating that the presently investigated oil has little or no effect on the two tested compounds even though the polarity of the oil is much less than soil organic matter (SOM). Therefore, specific interactions with the active groups (aromatic and polar domains) are dominantly responsible for the sorption of polar sorbates, and thus their sorption is controlled by available sorption sites. This study showed that the oil has the potential to be a dominant sorptive phase for nonpolar pollutants when compared to SOM, but hardly so for polar compounds. The results may aid in a better understanding of the role of the aliphatic and aromatic domains in sorption of nonpolar and polar organic pollutants.     

Sorption of atrazine and phenanthrene by organic matter fractions in soil and sediment

Atrazine and phenanthrene (Phen) sorption by nonhydrolyzable carbon (NHC), black carbon (BC), humic acid (HA) and whole sediment and soil samples was examined. Atrazine sorption isotherms were nearly linear. The single-point organic carbon (OC)-normalized distribution coefficients (K_OC) of atrazine for the isolated HA1, NHC1 and BC1 from sediment 1 (ST1) were 36, 550, and 1470 times greater than that of ST1, respectively, indicating the importance of sediment organic matter, particularly the condensed fractions (NHC and BC). Similar sorption capacity of atrazine and Phen by NHC but different isotherm nonlinearity indicated different sorption domains due to their different structure and hydrophobicity. The positive relationship between (O + N)/C ratios of NHC and atrazine log K_OC at low concentration suggests H-bonding interactions. This study shows that sediment is probably a less effective sorbent for atrazine than Phen, implying that atrazine applied in sediments or soils may be likely to leach into groundwater.     

Sorption of alpha and beta hydrophobic endosulfan in a Vertisol from southeast region of Turkey

Endosulfan has been applied to control numerous insects in a variety of food and non-food crops. Limited information is available on dynamics of this pesticide in the soil. The objective of this research was to determine the adsorption–desorption behavior of the alpha (α) and beta (β) endosulfan in a Vertisol from the southeast region of Turkey, where cotton is the main crop in the large irrigated lowlands. The α and β endosulfan were adsorbed considerably and Freundlich adsorption–desorption isotherms fitted the α and β endosulfan data (R² > 0.98). Freundlich adsorption coefficients (K_f) for the α endosulfan ranged between 21.63 and 16.33 while for the β endosulfan they were between 14.01 and 17.98 for the Ap and Bw2 horizons. The difference of K_f values of α and β endosulfan for two horizons were explained with the slight difference in the amount of organic matter and clay, but considerable difference in Fe contents of the two horizons. Alpha and β endosulfan K_fd values were 118.03 and 45.81 for the Ap and 48.08 and 68.71 for the Bw2 horizons. Higher adsorption and desorption behavior of the endosulfan isomers for the same horizon was attributed to poor physical bonding between the endosulfan molecule and the surfaces of fundamental soil particles. This fact is thought to increase the effective use of endosulfan in agriculture with a possibility of its movement to the surface and groundwater in the Vertisol studied.     

Capability and limitations of first-order and diffusion approaches to describe long-term sorption of chlortoluron in soil

This paper compares the capability of a first-order and a spherical diffusion model to describe and predict long-term sorption and desorption processes of chlortoluron in two soils. Chlortoluron sorption was investigated at different time scales utilizing one rate experiment (120 days) and two sorption/desorption experiments. Experimental periods for sorption and desorption were set to 1 day (five desorption steps) and 30 days (three desorption steps), respectively. Upon fitting, the two models satisfactorily described the whole set of data. The spherical diffusion model performed better than the first-order model. We then tested the predictive capability of the models by predicting 30-day sorption/desorption data using kinetic parameters fitted on 1-day sorption/desorption data only. While the spherical diffusion model was able to predict the 30-day data set, the first-order model failed completely. Fitting both models to subsets of the data corresponding to different experimental time scales revealed that the rate parameter as well as the Freundlich coefficient of the first-order model are strongly time-dependent--a property that is not shared by parameters of the spherical diffusion model. The apparent stability of the spherical diffusion model with regard to time dependency of its parameters indicates that sorptive uptake may be diffusion-controlled. This also explains the models greater predictive power across different time scales compared to the first-order model. Finally, we investigate the suitability of solute class specific log-linear relationships between the first-order rate parameter and the Freundlich coefficient presented by earlier researchers in the light of the time dependency observed for the parameters of the first-order model.