Cr(VI) and COD removal from landfill leachate by polyculture constructed wetland at a pilot scale

Four subsurface horizontal-flow constructed wetlands (CWs) at a pilot scale planted with a polyculture of the tropical plants Gynerium sagittatum (Gs), Colocasia esculenta (Ce) and Heliconia psittacorum (He) were evaluated for 7 months. The CW cells with an area of 17.94 m² and 0.60 m (h) each and 0.5 m of gravel were operated at continuous gravity flow (Q?=?0.5 m³ day^?1) and a theoretical HRT of 7 days each and treating landfill leachate for the removal of filtered chemical oxygen demand (COD_f), BOD₅, TKN, NH₄ ⁺, NO₃ ^?, PO₄ ^3?–P and Cr(VI). Three CWs were divided into three sections, and each section (5.98 m²) was seeded with 36 cuttings of each species (plant density of six cuttings per square metre). The other unit was planted randomly. The final distributions of plants in the bioreactors were as follows: CW I (He-Ce-Gs), CW II (randomly), CW III (Ce-Gs-He) and CW IV (Gs-He-Ce). The units received effluent from a high-rate anaerobic pond (BLAAT®). The results show a slightly alkaline and anoxic environment in the solid-liquid matrix (pH?=?8.0; 0.5–2 mg L^?1 dissolved oxygen (DO)). COD_f removal was 67 %, BOD₅ 80 %, and TKN and NH₄ ⁺ 50–57 %; NO₃ ^? effluents were slightly higher than the influent, PO₄ ^3?–P (38 %) and Cr(VI) between 50 and 58 %. CW IV gave the best performance, indicating that plant distribution may affect the removal capacity of the bioreactors. He and Gs were the plants exhibiting a translocation factor (TF) of Cr(VI) >1. The evaluated plants demonstrated their suitability for phytoremediation of landfill leachate, and all of them can be categorized as Cr(VI) accumulators. The CWs also showed that they could be a low-cost operation as a secondary system for treatment of intermediated landfill leachate (LL).     

Evaluation of Acinetobacter sp. B9 for Cr (VI) resistance and detoxification with potential application in bioremediation of heavy-metals-rich industrial wastewater

Present work demonstrates Cr (VI) detoxification and resistance mechanism of a newly isolated strain (B9) of Acinetobacter sp. Bioremediation potential of the strain B9 is shown by simultaneous removal of major heavy metals including chromium from heavy-metals-rich metal finishing industrial wastewater. Strain B9 tolerate up to 350 mg L^?1 of Cr (VI) and also shows level of tolerance to Ni (II), Zn (II), Pb (II), and Cd (II). The strain was capable of reducing 67 % of initial 7.0 mg L^?1 of Cr (VI) within 24 h of incubation, while in presence of Cu ions 100 % removal of initial 7.0 and 10 mg L^?1 of Cr (VI) was observed with in 24 h. pH in the range of 6.0–8.0 and inoculum size of 2 % (v/v) were determined to be optimum for dichromate reduction. Fourier transform infrared spectroscopy and transmission electron microscopy studies suggested absorption or intracellular accumulation and that might be one of the major mechanisms behind the chromium resistance by strain B9. Scanning electron microscopy showed morphological changes in the strain due to chromium stress. Relevance of the strain for treatment of heavy-metals-rich industrial wastewater resulted in 93.7, 55.4, and 68.94 % removal of initial 30 mg L^?1 Cr (VI), 246 mg L^?1 total Cr, and 51 mg L^?1 Ni, respectively, after 144 h of treatment in a batch mode.     

Bioremediation of chromium by novel strains Enterobacter aerogenes T2 and Acinetobacter sp. PD 12 S2

Purpose

This study had an objective to identify the most potent chromium-resistant bacteria isolated from tannery effluent and apply them for bioremediation of chromium in tannery effluents.

Methods

Two such strains (previously characterized and identified by us)??Enterobacter aerogenes (NCBI GenBank USA Accession no. GU265554) and Acinetobacter sp. PD 12 (NCBI GenBank USA Accession no. GU084179)??showed powerful chromium resistivity and bioremediation capabilities among many stains isolated from tannery waste. Parameters such as pH, concentration of hexavalent chromium or Cr (VI), and inoculum volume were varied to observe optimum bioconversion and bioaccumulation of Cr (VI) when the said strains were grown in M9 minimal salt media. E. aerogenes was used to remediate chromium from tannery effluents in a laboratory level experiment.

Results

Observation by Scanning Electron Microscope and chromium peak in Energy Dispersive X-ray Spectroscopic microanalysis revealed that E. aerogenes helped remediate a moderate amount of Cr (VI) (8?C16?mg?L^?1) over a wide range of pH values at 35?C37°C (within 26.05?h). High inoculum percentage of Acinetobacter sp. PD 12 also enabled bioremediation of 8?C16?mg?L^?1 of Cr (VI) over a wide range of temperature (25?C37°C), mainly at pH?7 (within 63.28?h). The experiment with real tannery effluent gave very encouraging results.

Conclusion

The strain E. aerogenes can be used in bioremediation of Cr (VI) since it could work in actual environmental conditions with extraordinarily high capacity.     

Influence of alum on cyanobacterial blooms and water quality of earthen fish ponds

Eruption of blue-green algal blooms occurs frequently in eutrophic lakes and fish ponds, with associated unpleasant odor and horrid scums. In the present study, we conducted a pre-test experiment in 3 m³ outdoor concrete ponds to determine the optimum concentration of aluminum sulfate (alum) required for reduction of the cyanobacterial blooms without negative effect on fish growth. As a consequence, 10 mg L^?1 alum was named as the optimum concentration that was applied in 1000 m³ earthen fish ponds. Obtained results showed that Secchi disc values significantly increased from 10 to 24 cm after 14 days of alum application. Alum-treated ponds showed a reduction in total phytoplankton counts by 94 and 96 % compared to the corresponding controls after 10 and 14 days, respectively. Abundance of blue-green algae in the treated ponds was decreased by 98 % compared to the corresponding control after 14 days of alum application. Consequently, dissolved oxygen, pH, total phosphorus, orthophosphate, and chlorophyll “a” content declined significantly. Our study revealed that using 10 mg L^?1 of alum is an effective way to control cyanobacterial blooms in eutrophic waters, especially in fish ponds, without negative effect in water quality.     

Genotoxicity potential of a new natural formicide

Background, aim, and scope

Assessment of environmental impacts from pesticide utilization should include genotoxicity studies, where the possible effects of mutagenic/genotoxic substances on individuals are assessed. In this study, the genotoxicity profile of the new formicide Macex® was evaluated with two genotoxicity tests, namely, the micronucleus test with mouse bone marrow and Vicia faba, and a mutagenicity test using the Ames Salmonella assay.

Materials and methods

The bacterial reverse mutation test (Salmonella typhimurium strains TA97, TA98, TA100, TA102, and TA1535), the Vicia root tip and mouse micronucleus tests were conducted according to published protocols.

Results

In the range of the formicide Macex® concentrations tested from 0.06 to 1.0 g?L^?1 (or mgkg^?1 in the mouse test), no genotoxicity was observed in the prokaryotic or eukaryotic test organisms. However, at Macex® concentrations of 0.5 g?L^?1 and above a significant decrease in the mitotic index (P?≤?0.05) in the V. faba was observed. Micronucleus formation was likewise increased in the test organism at concentrations starting at 2.0 g?L^?1.

Conclusions

These data allow us to classify this natural formicide preparation as a product with no geno-environmental-impact when applied at recommended concentrations.

     

Copper bioaccumulation,photosystem II functioning,and oxidative stress in the seagrass <Emphasis Type="Italic">Cymodocea nodosa</Emphasis> exposed to copper oxide nanoparticles

Photosynthetic activity, oxidative stress, and Cu bioaccumulation in the seagrass Cymodocea nodosa were assessed 4, 12, 24, 48, and 72 h after exposure to two copper oxide nanoparticle (CuO NP) concentrations (5 and 10 mg L^?1). CuO NPs were characterized by scanning electron microscopy (SEM) and dynamic light scattering measurements (DLS). Chlorophyll fluorescence analysis was applied to detect photosystem II (PSII) functionality, while the Cu accumulation kinetics into the leaf blades was fitted to the Michaelis-Menten equation. The uptake kinetics was rapid during the first 4 h of exposure and reached an equilibrium state after 10 h exposure to 10 mg L^?1 and after 27 h to 5 mg L^?1 CuO NPs. As a result, 4-h treatment with 5 mg L^?1 CuO NPs, decreased the quantum yield of PS II photochemistry (Φ _PSΙΙ ) with a parallel increase in the regulated non-photochemical energy loss in PSII (Φ _NPQ ). However, the photoprotective dissipation of excess absorbed light energy as heat, through the process of non-photochemical quenching (NPQ), did not maintain the same fraction of open reaction centers (q _p ) as in control plants. This reduced number of open reaction centers resulted in a significant increase of H₂O₂ production in the leaf veins serving possibly as an antioxidant defense signal. Twenty-four-hour treatment had no significant effect on Φ _PSΙΙ and q _p compared to controls. However, 24 h exposure to 5 mg L^?1 CuO NPs increased the quantum yield of non-regulated energy loss in PSII (Φ _NO ), and thus the formation of singlet oxygen (¹O₂) via the triplet state of chlorophyll, possible because the uptake kinetics had not yet reached the equilibrium state as did 10 mg L^?1. Longer-duration treatment (48 and 72 h) had less effect on the allocation of absorbed light energy at PSII and the fraction of open reaction centers, compared to 4-h treatment, suggesting the function of a stress defense mechanism. The response of C. nodosa leaves to CuO NPs fits the “Threshold for Tolerance Model” with a threshold time (more than 4 h) required for induction of a stress defense mechanism, through H₂O₂ production.     

IMPACT OF FOUR PESTICIDES ON THE GROWTH AND METABOLIC ACTIVITIES OF TWO PHOTOSYNTHETIC ALGAE

The acute toxicity was determined for soil algae Chlorella kesslerei and Anabaena inaequalis, exposed to pesticides lindane, pentachlorophenol (PCP), isoproturon (IPU), and methyl parathion (MP). Toxicity markers included growth inhibition, chlorophyll biosynthesis, and total carbohydrate content, as a function of dose and time. Concentration response functions (EC₅₀) were estimated by probit data transformation and weighted linear regression analyses. Lindane's toxicity to Chlorella increased sharply with time (EC₅₀=7490, 10.3, 0.09 mg L^?1; 24, 48, 72 h), but remained nearly constant through 72 h with Anabaena (8.7?6.7 mg L^?1; 24–72 h). PCP at low concentrations stimulated algal growth and chlorophyll a production, an effect reversed at higher doses. Anabaena was less tolerant of PCP and MP than was Chlorella. The 96-h static EC₅₀ values for Chlorella were: 0.003, 34, 0.05, and 291 mg L^?1 for lindane, PCP, isoproturon, and MP, respectively; for Anabaena, these were 4.2, 0.13, 0.21, and 19 mg L^?1. Carbohydrate production responses were similar to those of cell density (growth) and chlorophyll biosynthesis, with MP having the lowest adverse impact. The overall relative toxicity among the four tested pesticides was: for Chlorella, lindane>IPU?PCP?MP; and for Anabaena, PCP>IPU>lindane>MP. The results confirm that toxicants such as these pesticides may affect individual (though related) species to significantly different degrees.     

Fungicide sensitivity of Trichoderma spp. from Agaricus bisporus farms in Serbia

Trichoderma species, the causal agents of green mould disease, induce great losses in Agaricus bisporus farms. Fungicides are widely used to control mushroom diseases although green mould control is encumbered with difficulties. The aims of this study were, therefore, to research in vitro toxicity of several commercial fungicides to Trichoderma isolates originating from Serbian and Bosnia-Herzegovina farms, and to evaluate the effects of pH and light on their growth. The majority of isolates demonstrated optimal growth at pH 5.0, and the rest at pH 6.0. A few isolates also grew well at pH 7. The weakest mycelial growth was noted at pH 8.0–9.0. Generally, light had an inhibitory effect on the growth of tested isolates. The isolates showed the highest susceptibility to chlorothalonil and carbendazim (ED₅₀ less than 1 mg L^?1), and were less sensitive to iprodione (ED₅₀ ranged 0.84–6.72 mg L^?1), weakly resistant to thiophanate-methyl (ED₅₀ = 3.75–24.13 mg L^?1), and resistant to trifloxystrobin (ED₅₀ = 10.25–178.23 mg L^?1). Considering the toxicity of fungicides to A. bisporus, carbendazim showed the best selective toxicity (0.02), iprodione and chlorothalonil moderate (0.16), and thiophanate-methyl the lowest (1.24), while trifloxystrobin toxicity to A. bisporus was not tested because of its inefficiency against Trichoderma isolates.     

In vitro Cr(VI) reduction by cell-free extracts of chromate-reducing bacteria isolated from tannery effluent irrigated soil

Four efficient Cr(VI)-reducing bacterial strains were isolated from rhizospheric soil of plants irrigated with tannery effluent and investigated for in vitro Cr(VI) reduction. Based on 16S rRNA gene sequencing, the isolated strains SUCR44, SUCR140, SUCR186, and SUCR188 were identified as Bacillus sp. (JN674188), Microbacterium sp. (JN674183), Bacillus thuringiensis (JN674184), and Bacillus subtilis (JN674195), respectively. All four isolates could completely reduce Cr(VI) in culture media at 0.2 mM concentration within a period of 24–120 h; SUCR140 completely reduced Cr(VI) within 24 h. Assay with the permeabilized cells (treated with Triton X-100 and Tween 80) and cell-free assay demonstrated that the Cr(VI) reduction activity was mainly associated with the soluble fraction of cells. Considering the major amount of chromium being reduced within 24–48 h, these fractions could have been released extracellularly also during their growth. At the temperature optima of 28 °C and pH?7.0, the specific activity of Cr(VI) reduction was determined to be 0.32, 0.42, 0.34, and 0.28 μmol Cr(VI)?min^?1?mg^?1 protein for isolates SUCR44, SUCR140, SUCR186, and SUCR188, respectively. Addition of 0.1 mM NADH enhanced the Cr(VI) reduction in the cell-free extracts of all four strains. The Cr(VI) reduction activity in cell-free extracts of all the isolates was stable in presence of different metal ions tested except Hg²⁺. Beside this, urea and thiourea also reduced the activity of chromate reduction to significant levels.     

Electrochemical Monitoring of Methylparathion Degradation in an Acid Aqueous Medium in Presence of Cu(II)

Abstract

A study was undertaken to determine the effect of Cu(II) in degradation of methylparathion (o,o-dimethyl o, 4-nitrophenyl phosphoriotioate) in acid medium. Initial electrochemical characterization of Cu(II) and methylparathion was done in an aqueous medium at a pH range of 2–7. Cu(II) was studied in the presence of different anions and it was observed that its electroactivity depends on pH and is independent of the anion used. Methylparathion had two reduction signals at pH ≤ 6 and only one at pH > 6. The pesticide's transformation kinetic was then studied in the presence of Cu(II) in acid buffered aqueous medium at pH values of 2, 4, and 7. Paranitrophenol appeared as the only electroactive product at all three pH values. The reaction was first order and had k values of 5.2 × 10^?3 s^?1 at pH 2, 5.5 × 10^?3 s^?1 at pH 4 and 9.0 × 10^?3 s^?1 at pH 7. It is concluded that the principal degradation pathway of methylparathion in acid medium is a Cu(II) catalyzed hydrolysis reaction.     

Stormwater harvesting from landscaped areas: effect of herbicide application on water quality and usage

The suitability of stormwater harvested from pervious pavement system (PPS) structures for reuse purposes was investigated in conditions where glyphosate-containing herbicides (GCH) are applied as part of PPS maintenance procedure. The experiment was based on the four-layered design previously described as detailed in CIRIA C582. Results indicated that the highest sodium absorption ratio (SAR) of 1.6 recorded in this study, was less than that at which loss of permeability begins to occur as well as deterioration of matrix structure. Furthermore, the maximum electrical conductivity (ECw) of 2990 μS cm^?1, recorded for 7200 mg L^?1 concentration (GCH) was slightly below the unstable classification range at which salinity problems related to water quality occur such that salts accumulate in the root zone to the extent that crop yields are adversely affected. However, GCH concentration of 720 mg L^?1 was within ‘permissible’ range while that of 72 mg L^?1 was within ‘excellent’ range. Current study raises some environmental concerns owing to the overall impact that GCH at concentrations above 72 mg L^?1 exerts on the net performance of the organic decomposers, heavy metal and hydrocarbon release from the system and thus, should be further investigated. However, effluent from all the test models including those dosed with high GCH concentration of 7200 mg L^?1 do not pose any threat in terms of infiltration or deterioration associated with salinity although, there are indications that high dosage of the herbicide could lead to an elevated electrical conductivity of the recycled water.

Open image in new window

Graphical abstract Impact of herbicide on irrigation water quality

     

Synthesis of α-Fe2O3 nanofibers for applications in removal and recovery of Cr(VI) from wastewater

Purpose

Nanomaterials such as iron oxides and ferrites have been intensively investigated for water treatment and environmental remediation applications. The purpose of this work is to synthesize α-Fe₂O₃ nanofibers for potential applications in removal and recovery of noxious Cr(VI) from wastewater.

Methods

α-Fe₂O₃ nanofibers were synthesized via a simple hydrothermal route followed by calcination. The crystallographic structure and the morphology of the as-prepared α-Fe₂O₃ nanofibers were characterized by X-ray diffraction, scanning electron microscope, and transmission electron microscope. Batch adsorption experiments were conducted, and Fourier transform infrared spectra were recorded before and after adsorption to investigate the Cr(VI) removal performance and adsorption mechanism. Langmuir and Freundlich modes were employed to analyze the adsorption behavior of Cr(VI) on the α-Fe₂O₃ nanofibers.

Results

Very thin and porous α-Fe₂O₃ nanofibers have been successfully synthesized for investigation of Cr(VI) removal capability from synthetic wastewater. Batch experiments revealed that the as-prepared α-Fe₂O₃ nanofibers exhibited excellent Cr(VI) removal performance with a maximum adsorption capacity of 16.17 mg g^?1. Furthermore, the adsorption capacity almost kept unchanged after recycling and reusing. The Cr(VI) adsorption process was found to follow the pseudo-second-order kinetics model, and the corresponding thermodynamic parameters ΔG°, ΔH°, and ΔS° at 298 K were calculated to be ?26.60 kJ?mol^?1, ?3.32 kJ?mol^?1, and 78.12 J?mol^?1 K^?1, respectively.

Conclusions

The as-prepared α-Fe₂O₃ nanofibers can be utilized as efficient low-cost nano-absorbents for removal and recovery of Cr(VI) from wastewater.     

Heterogeneous photocatalytic degradation of methyl orange in schwertmannite/oxalate suspension under UV irradiation

Introduction

Schwertmannite was synthesized through an oxidation of FeSO₄ by Acidithiobacillus ferrooxidans LX5 cell suspension at an initial pH?2.5 and 28°C for 3?days and characterized using X-ray diffraction spectroscopy and scanning electron microscope. The schwertmannite photocatalytic degradation of methyl orange (MO) by oxalate was investigated at different initial pH values, concentrations of schwertmannite, oxalate, and MO.

Results

The results demonstrated that photodegradation of MO in the presence of schwertmannite or oxalate alone was very weak. However, the removal of MO was significantly enhanced when schwertmannite and oxalate coexisted in the reaction system. Low pH (4 or less) was beneficial to the degradation of MO. The optimal doses of schwertmannite and oxalate were 0.2?g?L^?1 and 2?mM, respectively. Hydroxyl radicals (·OH) and Fe(II), the intermediate products, were also examined during the reaction to explore their correlation with the degradation of MO.

Conclusion

A possible mechanism for the photocatalytic decomposition of MO in the study was proposed. The formation of Fe(III)-oxalate complexes on the surface of schwertmannite was a precursor of H₂O₂ and Fe(II) production, further leading to the yield of ·OH responsible for the decomposition of MO.     

Modelling the adsorption of mercury onto natural and aluminium pillared clays

Introduction

The removal of heavy metals by natural adsorbent has become one of the most attractive solutions for environmental remediation. Natural clay collected from the Late Cretaceous Aleg formation, Tunisia was used as a natural adsorbent for the removal of Hg(II) in aqueous system.

Methods

Physicochemical characterization of the adsorbent was carried out with the aid of various techniques, including chemical analysis, X-ray diffraction, Fourier transform infrared and scanning electron micrograph. Batch sorption technique was selected as an appropriate technique in the current study. Method parameters, including pH, temperature, initial metal concentration and contact time, were varied in order to quantitatively evaluate their effects on Hg(II) adsorption onto the original and pillared clay samples. Adsorption kinetic was studied by fitting the experimental results to the pseudo-first-order and pseudo-second-order kinetic models. The adsorption data were also simulated with Langmuir, Freundlich and Temkin isotherms.

Results

Results showed that the natural clay samples are mainly composed of silica, alumina, iron, calcium and magnesium oxides. The sorbents are mainly mesoporous materials with specific surface area of <250 m² g^?1. From the adsorption of Hg(II) studies, experimental data demonstrated a high degree of fitness to the pseudo-second-order kinetics with an equilibration time of 240 min. The equilibrium data showed the best model fit to Langmuir model with the maximum adsorption capacities of 9.70 and 49.75 mg g^?1 for the original and aluminium pillared clays, respectively. The maximum adsorption of Hg(II) on the aluminium pillared clay was observed to occur at pH 3.2. The calculated thermodynamic parameters (?G°, ?H° and ?S°) showed an exothermic adsorption process. The entropy values varied between 60.77 and 117.59 J?mol^?1 K^?1, and those of enthalpy ranged from 16.31 to 30.77 kJ mol^?1. The equilibrium parameter (R _L) indicated that the adsorption of Hg(II) on Tunisian smectitic clays was favourable under the experimental conditions of this study.

Conclusion

The clay of the Aleg formation, Tunisia was found to be an efficient adsorbent for Hg(II) removal in aqueous systems.     

Removal of toxic ions (chromate, arsenate, and perchlorate) using reverse osmosis, nanofiltration, and ultrafiltration membranes

Rejection characteristics of chromate, arsenate, and perchlorate were examined for one reverse osmosis (RO, LFC-1), two nanofiltration (NF, ESNA, and MX07), and one ultrafiltration (UF and GM) membranes that are commercially available. A bench-scale cross-flow flat-sheet filtration system was employed to determine the toxic ion rejection and the membrane flux. Both model and natural waters were used to prepare chromate, arsenate, and perchlorate solutions (approximately 100 μg L⁻¹ for each anion) in mixtures in the presence of other salts (KCl, K₂SO₄, and CaCl₂); and at varying pH conditions (4, 6, 8, and 10) and solution conductivities (30, 60, and 115 mS m⁻¹). The rejection of target ions by the membranes increases with increasing solution pH due to the increasingly negative membrane charge with synthetic model waters. Cr(VI), As(V), and rejection follows the order LFC-1 (>90%) > MX07 (25–95%)  ESNA (30–90%) > GM (3–47%) at all pH conditions. In contrast, the rejection of target ions by the membranes decreases with increasing solution conductivity due to the decreasingly negative membrane charge. Cr(VI), As(V), and rejection follows the order CaCl₂ < KCl  K₂SO₄ at constant pH and conductivity conditions for the NF and UF membranes tested. For natural waters the LFC-1 RO membrane with a small pore size (0.34 nm) had a significantly greater rejection for those target anions (>90%) excluding (71–74%) than the ESNA NF membrane (11–56%) with a relatively large pore size (0.44 nm), indicating that size exclusion is at least partially responsible for the rejection. The ratio of solute radius (r_i,s) to effective membrane pore radius (r_p) was employed to compare ion rejection. For all of the ions, the rejection is higher than 70% when the r_i,s/r_p ratio is greater than 0.4 for the LFC-1 membrane, while for di-valent ions (, , and ) the rejection (38–56%) is fairly proportional to the r_i,s/r_p ratio (0.32–0.62) for the ESNA membrane.     

Single and combined effects of aluminum (Al<Subscript>2</Subscript>O<Subscript>3</Subscript>) and zinc (ZnO) oxide nanoparticles in a freshwater fish, <Emphasis Type="Italic">Carassius auratus</Emphasis>

The increasing use of nanoparticles (NPs) worldwide has raised some concerns about their impact on the environment. The aim of the study was to assess the toxicity of metal oxide nanoparticles, singly or combined, in a freshwater fish (Carassius auratus). The fish were exposed for 7, 14, and 21 days to different concentrations of NPs (10 μg Al₂O₃.L^?1, 10 μg ZnO.L^?1, 10 μg Al₂O₃.L^?1 plus 10 μg ZnO.L^?1, 100 μg Al₂O₃.L^?1, 100 μg ZnO.L^?1, and 100 μg Al₂O₃.L^?1 plus 100 μg ZnO.L^?1). At the end of each exposure period, antioxidant enzyme activity (catalase, glutathione-S-transferase, and superoxide dismutase), lipid peroxidation, and histopathology were assessed in the gills and livers of C. auratus. The results show an increase in catalase (CAT) and superoxide dismutase (SOD) activity in the gills and livers of fish, especially after 14 days of exposure to single and combined NPs, followed by a reduction at 21 days. An increase in glutathione S-transferase (GST) was observed in gills after 7 days for all tested NP concentrations (single and combined); while in livers, a significant increase was determined after 14 days of exposure to 100 μg.L^?1 of both single ZnO and Al₂O₃ NPs. Lipid peroxidation (LPO) significantly increased in gills after 7 days of exposure to 100 μg.L^?1 Al₂O₃ NPs (single or combined). In livers, LPO increased significantly after 7 days of exposure to all tested concentrations of both single ZnO and Al₂O₃ (except for 10 μg Al₂O₃.L^?1), and after 14 days of exposure to ZnO (10 and 100 μg.L^?1) and Al₂O₃ (100 μg.L^?1)_. The results from histological observations suggest that exposure to metal oxide NPs affected both livers and gills, presenting alterations such as gill hyperplasia and liver degeneration. However, the most pronounced effects were found in gills. In general, this study shows that the tested NPs, single or combined, are capable of causing sub-lethal effects on C. auratus, but when combined, NPs seem to be slightly more toxic than when added alone.     

Removal of Cr(VI) onto Ficus carica biosorbent from water

The utilization of sustainable and biodegradable lignocellulosic fiber to detoxify the noxious Cr(VI) from wastewater is considered a versatile approach to clean up a contaminated aquatic environment. The aim of the present research is to assess the proficiency and mechanism of biosorption on Ficus carica bast fiber via isotherm models (Langmuir, Freundlich, Temkin, Harkin’s–Jura, and Dubinin–Radushkevich), kinetic models, and thermodynamic parameters. The biomass extracted from fig plant was characterized by scanning electron microscopy and Fourier-transform infrared spectroscopy. To optimize the maximum removal efficiency, different parameters like effect of initial concentration, effect of temperature, pH, and contact time were studied by batch method. The equilibrium data were best represented by the Langmuir isotherm model, and the maximum adsorption capacity of Cr(VI) onto biosorbent was found to be 19.68 mg/g. The pseudo-second-order kinetic model adequately described the kinetic data. The calculated values of thermodynamic parameters such as enthalpy change (?H ⁰), entropy change (?S ⁰), and free energy change (?G ⁰) were 21.55 kJ/mol, 76.24 J/mol?K, and ?1.55 kJ/mol, respectively, at 30 °C which accounted for spontaneous and endothermic processes. The study of adsorbent capacity for Cr(VI) removal in the presence of Na⁺, Mg²⁺, Ca²⁺, SO ₄ ^2? , HCO ₃ ^? and Cl^? illustrated that the removal of Cr(VI) increased in the presence of HCO^3? ions; the presence of Na⁺, SO ₄ ^2? or Cl^? showed no significant influence on Cr(VI) adsorption, while Ca²⁺ and Mg²⁺ ions led to an insignificant decrease in Cr(VI) adsorption. Further, the desorption studies illustrated that 31.10 % of metal ions can be removed from an aqueous system, out of which 26.63 % of metal ions can be recovered by desorption in first cycle and the adsorbent can be reused. The results of the scale-up study show that the ecofriendly detoxification of Cr(VI) from aqueous systems was technologically feasible.     

Bioaccumulation and trophic transfer of mercury in a food web from a large, shallow, hypereutrophic lake (Lake Taihu) in China

Purpose

Due to the fast development of industry and the overuse of agrichemicals in past decades, Lake Taihu, an important source of aquatic products for Eastern China, has simultaneously suffered mercury (Hg) contamination and eutrophication. The objectives of this study are to understand Hg transfer in the food web in this eutrophic, shallow lake and to evaluate the exposure risk of Hg through fish consumption.

Methods

Biota samples including macrophytes, sestons, benthic animals, and fish were collected from Lake Taihu in the fall of 2009. The total mercury (THg), methyl mercury (MeHg), ??¹³C and ??¹⁵N in the samples were measured.

Results and discussion

The signature for ??¹⁵N increased with the trophic levels. Along with a diet composed of fish, the significant relationship between the ??¹³C and ??¹⁵N indicated that a pelagic foraging habitat is the dominant pathway for energy transfer in Lake Taihu. The concentrations of THg and MeHg in the organisms varied dramatically by ??3 orders of magnitude from primary producers (macrophytes and sestons) to piscivorous fish. The highest concentrations of both THg (100 ng g^?1) and MeHg (66 ng g^?1), however, were lower than the guideline of 200 ng g^?1 of MeHg for vulnerable populations that is recommended by the World Health Organization (WHO). The daily intake of THg and MeHg of 92 and 56 ng day^?1 kg^?1 body weight, respectively, was generally lower than the tolerable intake of 230 ng day^?1 kg^?1 body weight for children recommended by the Joint FAO/WHO Expert Committee on Food Additives. Significant relationships between the ??¹⁵N and the logarithm of THg and MeHg showed an obvious biomagnification of Hg along the food web. The logarithmic bioaccumulation factor of MeHg in the fish (up to 5.7) from Lake Taihu, however, was relatively low compared to that of other aquatic ecosystems.

Conclusion

Health risk of exposure to Hg by consumption of fish for local residents is relatively low in the Lake Taihu area. Dilution of Hg levels in the phytoplankton induced by eutrophication is a possible factor inhibiting accumulation of MeHg in fish in eutrophic Lake Taihu.