Seepage from deep bedded and poultry litter systems

The work reported indicates that there could be a potential of ground water pollution by NO3-N from turkey facilities built on both sandy and clay soils. At four different depths (30.54, 61.08, 91.62, and 122.16 cm), the NO3-N levels for the clay soil were 1572, 497, 66, and 28 ppm, and those for the sandy soil were 293, 425, 324, and 164 ppm, respectively. No significant P increases were observed but there did exist a significant increase of K in the topsoil for both clay and sandy turkey structures. The results show that swine hoop houses with less than three or four years of age may not pose a threat to groundwater pollution due to the leaching of nutrients. The only dairy feedlot sampled in this study, although it has been used for more than 20 years, did not show leaching of NO3-N and P. However, it did show a significantly elevated concentration of potassium in the topsoil, as compared to the background sample. More sites should be investigated to verify this.     

Depleted N carryover, leaching and uptake for three years of irrigated corn

Deep percolation of nitrate can contribute to the deterioration of groundwater resources. Leaching of nitrate is a complex process affected by fertilizer and irrigation practices, efficiency of N use by the crop, and how the soil's water holding capacity and water transmission properties are affected by soil texture. Depleted (¹⁵NH₄)₂SO₄ fertilizer at N rates of 0, 125, 250 and 375 kg ha⁻¹ was applied annually for 3 years to continuous corn grown within three different water regimes. This time period and the labeled N permitted an evaluation of N use efficiency by the crop and NO₃ leaching and carryover on a Weld silty clay loam, a fine-textured soil, typical of the “hardland” soils of the semi-arid Great Plains. Three water regimes, W₁ ( 1.5 ET), W₂ ( ET) and W₃ ( 0.8 ET), were used. Beneath each plot within each water regime, Duke-Haise vacuum trough extractors were installed under undisturbed soil profiles at 1.22-m depth to measure weekly percolate and the NO₃ concentration in the percolate. The corn was harvested in the fall in the dent stage to measure the total above-ground biomass N uptake. Soil profiles (1.8 m) were sampled annually in the fall after crop harvest to determine NO₃---N in the soil or carryover.Great variability was encountered in measuring the amount of extractor water and its NO₃ content under each water regime, which made estimates of N03 leaching losses unreliable. Also, the variability demonstrates formidable problems in quantifying percolation losses with vacuum trough extractors under undisturbed fine-textured soil profiles. With the highest N rate of 376 kg ha⁻¹ yr⁻¹ and within the water regime W₁, where leaching was expected to be greatest, only 1% of the cumulative labeled N applied was found in extractor waters and most movement of the labeled N into extractors occurred the third year. The 125-kg-ha⁻¹ yr⁻¹ fertilizer N rate significantly increased the crop yield over the unfertilized plots without increasing residual NO₃---N accumulation; whereas fertilizer N rates of > 125 kg ha⁻¹ yr⁻¹ did not appreciably increase plant yields over the 125-kg-ha⁻¹-N rate, but did appreciably increase residual NO₃.     

Sorptive interactions and binding of δ‐endotoxin protein from bacillus thuringiensis subsp. kurstaki inforest soils

Abstract

The adsorption, desorption and binding of the insecticidal protein from Bacillus thuringiensis subsp. kurstaki (Btk toxin) onto autoclaved sandy and clay loam forest soils were studied at 23°C in a buffer medium (pH 10.2) using the precipitated protein mixture (active + inactive) obtained from a commercial Btk formulation. The active protein in the buffer solution was quantified by ELISA technique. Maximum adsorption of the toxin onto the sandy (301 μg/g) and clay (474 μg/g) loam soils was found to occur after 3 and 4 hours of agitation, respectively. Adsorption of the toxin was higher in the clay loam soil than in sandy loam. Adsorption parameters were calculated using the Freundlich and linear isotherm equations. The K_F and 1/n values for the soils were 1.12 and 1.48 (sandy), and 20.42 and 0.874 (clay), respectively, indicating stronger affinity of the toxin for the clay compared to the sandy loam soil. The linear model showed deviations at higher concentrations, nevertheless using the best fit, K_D and K_OC values were computed for the two soils. For sandy loam, the K_D and K_OC values were 9.38 and 391, respectively; the corresponding values for clay loam were 13.19 and 425, confirming the higher sorption affinity of the toxin for clay loam. The adsorption data did not fit the Langmuir equation because of heterogeneity of the soil surface. Desorption studies showed that more than half of the adsorbed toxic protein remained firmly attached to sandy (162.6 μg/g or 54.5%) and clay (314.0 μg/g or 67.4%) loam soils after six 0.5‐h washes (total 3.0 h wash time). Although the toxin appears to be a non‐leacher, its lateral mobility, soil persistence and biological consequences, including bioavailability of the bound residues, are poorly understood and require further investigation.     

Consequences of nitrate leaching following stem-only harvesting of Swedish forests are dependent on spatial scale

Short-term increases in soil solution nitrate (NO₃⁻) concentration are often observed after forest harvest, even in N-limited systems. We model NO₃⁻ leaching below the rooting zone as a function of site productivity. Using national forest inventories and published estimates of N attenuation in rivers and the riparian zone, we estimate effects of stem-only harvesting on NO₃⁻ leaching to groundwater, surface waters and the marine environment. Stem-only harvesting is a minor contributor to NO₃⁻ pollution of Swedish waters. Effects in surface waters are rapidly diluted downstream, but can be locally important for shallow well-waters as well as for the total amount of N reaching the sea. Harvesting adds approximately 8 Gg NO₃-N to soil waters in Sweden, with local concentrations up to 7 mg NO₃-N l⁻¹. Of that, ∼3.3 Gg reaches the marine environment. This is ∼3% of the overall Swedish N load to the Baltic.     

Phytotoxicity of atrazine and alachlor in soil amended with sludge,manure and activated carbon

Abstract

Greenhouse studies were conducted to determine the influence of waste‐activated carbon (WAC), digested municipal sewage sludge (DMS), and animal manure on herbicidal activity of atrazine [2‐chloro‐4‐(ethylamino)‐6‐(isopropylamino)‐s‐trazine] and alachlor [2‐chloro‐2’,6'‐diethyl‐N‐(methoxymethyl)acetanilide] in a Plainfield sandy soil. Amendments generally reduced bioactivity against oat (Avena sativa L.) and Japanese millet (E. crus‐galli frumentacea). The extent to which herbicide phytotoxicity was inhibited depended upon the application rate and the kind of soil amendment. WAC, applied at the loading rate of 2.1 mt C/ha, showed a significant inhibitory effect on both herbicides. In DMS‐ and manure‐amended soil, the reduction of atrazine activity was not significant at the rate of 8.4 mt C/ha, but reduction of alachlor activity was significant at the rate of 4.2 mt C/ha. Despite inhibition of herbicidal activity, the ED₅₀ of atrazine and alachlor was below 2 ppm in most of the amendment treatments. Before adopting carbon‐rich waste amendments as management practices for controlling pesticide leaching in coarse‐textured soils, further studies are needed to characterize how alterations in sorption, leaching and degradation may affect herbicidal activity.     

A classification and regression tree model of controls on dissolved inorganic nitrogen leaching from European forests

Often, there is a non-linear relationship between atmospheric dissolved inorganic nitrogen (DIN) input and DIN leaching that is poorly captured by existing models. We present the first application of the non-parametric classification and regression tree approach to evaluate the key environmental drivers controlling DIN leaching from European forests. DIN leaching was classified as low (<3), medium (3-15) or high (>15 kg N ha⁻¹ year⁻¹) at 215 sites across Europe. The analysis identified throughfall NO₃⁻ deposition, acid deposition, hydrology, soil type, the carbon content of the soil, and the legacy of historic N deposition as the dominant drivers of DIN leaching for these forests. Ninety four percent of sites were successfully classified into the appropriate leaching category. This approach shows promise for understanding complex ecosystem responses to a wide range of anthropogenic stressors as well as an improved method for identifying risk and targeting pollution mitigation strategies in forest ecosystems.     

Effects of metsulfuron‐methyl on microbial biomass and populations in soils

Abstract

Effects of the herbicide metsulfuron‐methyl on soil microorganisms and their activities in two soils were evaluated under laboratory conditions. Measurements included their populations, soil respiration, and microbial biomass. In the clay soil, bacterial populations decreased with increasing concentration of metsulfuron‐methyl during the first 9 days of incubation but exceeded that of the control soil from day 27 onward. In the sandy loam soil, the herbicide reduced bacterial populations during the first 3 days after application, but these increased to the level of untreated controls after 9 days’ incubation. Fungal populations in both soils increased with increasing metsulfuron‐methyl concentrations, especially in the sandy loam soil. CO₂ evolution was stimulated in both soils in the presence of the herbicide initially, but decreased during days 3 to 9 of the incubation period before increasing again afterward. The presence of metsulfuron‐methyl in the soil increased microbial biomass, except in sandy loam soil at the first day of incubation.     

Effects of Soil Amendments at a Heavy Loading Rate Associated with Cover Crops as Green Manures on the Leaching of Nutrients and Heavy Metals from a Calcareous Soil

The potential risk of groundwater contamination by the excessive leaching of N, P and heavy metals from soils amended at heavy loading rates of biosolids, coal ash, N‐viro soil (1:1 mixture of coal ash and biosolids), yard waste compost and co‐compost (3:7 mixture of biosolids to yard wastes), and by soil incorporation of green manures of sunn hemp (Crotalaria juncea) and sorghum sudangrass (Sorghum bicolor × S. bicolor var. sudanense) was studied by collecting and analyzing leachates from pots of Krome very gravelly loam soil subjected to these treatments. The control consisted of Krome soil without any amendment. The loading rate was 205 g pot^? 1 for each amendment (equivalent to 50 t ha^? 1 of the dry weight), and the amounts of the cover crops incorporated into the soil in the pot were those that had been grown in it. A subtropical vegetable crop, okra (Abelmoschus esculentus L.), was grown after the soil amendments or cover crops had been incorporated into the soil. The results showed that the concentration of NO₃‐N in leachate from biosolids was significantly higher than in leachate from other treatments. The levels of heavy metals found in the leachates from all amended soils were so low, as to suggest these amendments may be used without risk of leaching dangerous amounts of these toxic elements. Nevertheless the level of heavy metals in leachate from coal ash amended soil was substantially greater than in leachates from the other treatments. The leguminous cover crop, sunn hemp, returned into the soil, increased the leachate NO₃‐N and inorganic P concentration significantly compared with the non‐legume, sorghum sudangrass. The results suggest that at heavy loading rates of soil amendments, leaching of NO₃ ^? could be a significant concern by application of biosolids. Leaching of inorganic P can be increased significantly by both co‐compost and biosolids, but decreased by coal ash and N‐viro soil by virtue of improved adsorption. The leguminous cover crop, sunn hemp, when incorporated into the soil, can cause the concentration of NO₃‐N to increase by about 7 fold, and that of inorganic P by about 23% over the non‐legume. Regarding the metals, biosolids, N‐viro soil and coal ash significantly increased Ca and Mg concentrations in leachates. Copper concentration in leachate was increased by application of biosolids, while Fe concentration in leachates was increased by biosolids, coal ash and co‐compost. The concentrations of Zn, Mo and Co in leachate were increased by application of coal ash. The concentrations of heavy metals in leachates were very low and unlikely to be harmful, although they were increased significantly by coal ash application.     

Calculation of σz and H for an Observed Vertical Profile of Concentration

ABSTRACT

In the present work, nitrous oxide emissions were estimated [mg/L] by the use of lysimeters under the closed chamber technique for a six month period. The lysimeters were classified by the type of irrigation used: one for drinking water, and the other for treated wastewater. Each lysimeter had two different types of soil (sand and clay), based on the types of soil in Chihuahua City, Mexico. An additional classification based on the depth was done (reticular and vadose zone). Each zone collected gas by the use of a closed chamber technique, allowing the samples to be taken for subsequent quantification and analysis by gas chromatography. A statistical analysis of variance (ANOVA) and principal components analysis (PCA) were conducted to identify the most influential variables or parameters in the formation of nitrous oxide. The variables that were considered for analysis were total Kjeldahl nitrogen (TKN), ammoniacal nitrogen (NH3-N), nitrate nitrogen (NO3-N), and nitrite nitrogen (NO2-N), along with meteorological parameters. In total, 58944 mg/L of N2O were emitted during the measurement period. The results showed that concentration emissions of N2O where the type of soil is sandy were smaller than those of clay soil, while the mean concentration in the vadose zone was higher than those in the reticular zone, regardless the type of soil. The parameters that showed greater influence in the N2O emissions were NO2-N and NO3-N concentrations. Temperature also played an important role in the emissions (the highest emissions were emitted during the cold months). Furthermore, denitrification appeared to be the dominant process in the production of nitrous oxide in soils.

Implications: Nitrous oxide (N₂O) emissions produced in lysimeters with two types of soil (sand and clay) at two different depths (vadose and reticular zones) using treated waste water showed that the higher emissions of N₂O are derived from clay soils in vadose zone; it could be due to the formation of clogging that favors the formation of anoxic conditions for the denitrification process. The parameters that showed more influence in the N₂O emissions were nitrite (NO₂-N) and nitrate (NO₃-N) concentrations along with the temperature.     

Adsorption behavior of RH‐5992 insecticide onto sandy and clay loam forest soils

Abstract

Adsorption‐desorption behavior of RH‐5992 [Mimic®, N'‐t‐butyl‐N'‐(3,5‐dimethylbenzoyl)‐N‐(4‐ethylbenzoyl) hydrazine] in sandy and clay loam forest soils was studied using the batch equilibrium method. Adsorption was higher in the clay loam soil than in the sandy loam, and increased linearly with RH‐5992 concentration, but decreased with increasing pH and temperature. The adsorption data fit better to the Freundlich, than to the Langmuir equation. The K_D (linear adsorption constant) and K_F (Freundlich constant) were similar for each soil at 5, 15 and 25°C and decreased with increase of temperature, indicating that the enthalpy of adsorption was negative. The exponent of the Freundlich equation was close to unity for both soils at all three temperatures. The low E_a (energy of activation) indicated a diffusion‐controlled process during the initial stages of adsorption. The desorption isotherm differed from that of adsorption, and the linear desorption constant, K_D(d), was ca 25 times higher than the K_D, indicating that adsorption of RH‐5992 was not readily reversible. Evaluation of thermo‐dynamic parameters confirmed the presence of strong bonds between the solute and soil. These findings suggest that RH‐5992 has a limited potential for downward mobility leading to groundwater contamination.     

Influence of sugar cane vinasse on the sorption and degradation of herbicides in soil under controlled conditions

This study reports the influence of sugar cane vinasse on the persistence, sorption and leaching potential of diuron (3-(3,4-dichlorophenyl)-1,1-dimethylurea), hexazinone (3-cyclohexyl-6-(dimethylamino)-1-methyl-1,3,5-triazine-2,4-dione) and tebuthiuron (1-(5-tert-butyl-1,3,4-thiadiazol-2-yl)-1,3-dimethylurea) in both a clay and sandy soil from a tropical area of Brazil. The experiments were conducted out under controlled laboratory conditions. The addition of sugarcane vinasse to soil influenced the persistence and sorption of the herbicides in both the studied clay and sandy soils, with a considerable decrease in the diuron DT₅₀ values in clay soil. The Ground Water Ubiquity Score (GUS) Index classifies the herbicides as leachers in both soils and treatments, with the exception of diuron, which is classified as a non-leacher in clay soil-vinasse and as a transient herbicide in sandy soil. These results suggest that special attention should be given to areas such as those where the sandy soil was collected in this study, which is a recharge area of the Guarani Aquifer and is likely to experience groundwater contamination due to the high leaching potential of the applied pesticides.     

Sorption and leaching of flucetosulfuron in soil

Abstract

The adsorption–desorption and leaching of flucetosulfuron, a sulfonylurea herbicide, was investigated in three Indian soils. Freundlich adsorption isotherm described the sorption mechanism of herbicide with adsorption coefficients (K_f) ranging from 17.13 to 27.99 and followed the order: Clayey loam?>?Loam?>?Sandy loam. The K_f showed positive correlation with organic carbon (OC) (r?=?0.910) and clay content (r?=?0.746); but, negative correlation with soil pH (r = ?0.635). The adsorption isotherms were S-type suggesting that herbicide adsorption was concentration dependent and increased with increase in concentration. Desorption followed the sequence: sandy loam?>?clayey loam?>?loam . Hysteresis (H) was observed in all the three soils with H?<?1. Leaching of flucetosulfuron correlated positively with the soil pH; but, negatively with the OC content. Sandy loam soil (OC- 0.40%, pH ?7.25) registered lowest adsorption and highest leaching of flucetosulfuron while lowest leaching was found in the loam soil (pH ? 7.89, OC ? 0.65%). The leaching losses of herbicide increased with increase in the rainfall intensity. This study suggested that the soil OC content, pH and clay content played important roles in deciding the adsorption–desorption and leaching behavior of flucetosulfuron in soils.     

管道沉砂用作雨水花园土壤改良材料的可行性

以建筑黄砂为对照,采用排水管道清通作业产生的管道沉砂作为提高土壤渗透性能的改良材料,通过模拟土柱实验考察了雨水花园对路面径流污染的控制效果.实验结果表明,在装置初始运行阶段,模拟柱中污染物的淋出浓度迅速降低,污染地下水的风险很低;当污染物淋失达到稳定时,掺加同比例管道沉砂与建筑黄砂的模拟柱在提高土壤渗透速率方面效果相近,而对COD、TP、TSS、NH4+-N、NO3--N、重金属等污染物的去除两者效果则相差不大.结果表明,以管道沉砂作为土壤改良材料,在降低南方粘性土壤地区雨水花园的建造成本、实现废弃物的再利用方面具有良好前景.     

Heavy Metals in Urban Soils of East St. Louis,IL, Part I: Total Concentration of Heavy Metals in Soils

ABSTRACT

The city of East St. Louis, IL, has a history of abundant industrial activities including smelters of ferrous and non-ferrous metals, a coal-fired power plant, companies that produce organic and inorganic chemicals, and petroleum refineries. A protocol for soil analysis was developed to produce sufficient information on the extent of heavy metal contamination in East St. Louis soils. Soil cores representing every borough of East St. Louis were analyzed for heavy metals—As, Cd, Cu, Cr, Hg, Ni, Pb, Sb, Sn, and Zn. The topsoil contained heavy metal concentrations as high as 12.5 ppm Cd, 14,400 ppm Cu, ppm quantities of Hg, 1860 ppm Pb, 40 ppm Sb, 1130 ppm Sn, and 10,360 ppm Zn. Concentrations of Sb, Cu, and Cd were well correlated with Zn concentrations, suggesting a similar primary industrial source. In a sandy loam soil from a vacated rail depot near the bank of the Mississippi River, the metals were evenly distributed down to a 38-cm depth. The clay soils within a half-mile downwind of the Zn smelter and Cu products company contained elevated Cd (81 ppm), Cu (340 ppm), Pb (700 ppm), and Zn (6000 ppm) and displayed a systematic drop in concentration of these metals with depth. This study demonstrates the often high concentration of heavy metals heterogeneously distributed in the soil and provides baseline data for continuing studies of heavy metal soil leachability.     

Use of amendments to reduce leaching loss of phosphorus and other nutrients from a sandy soil in Florida

Goal, Scope and Background Transport of P from agricultural land contributes to the eutrophication of surface waters. Soil amendment is considered one of the best management practices (BMPs) to reduce P loss from sandy soils. Laboratory column leaching experiments were conducted to evaluate the effectiveness of different soil amendments in reducing P leaching from a typical sandy soil in Florida. Methods The tested amendments were CaCl₂, CaCO₃, Al(OH)₃, cellulose, and mill mud, and applied at the rate of 15 g/kg for a single amendment and each 7.5 g/kg if two amendments were combined. Leaching was conducted every four days for 32 days, 250 mL of deionized water being leached for each column per leaching event. Leachates were collected from each leaching event and analyzed for reactive P, PO₄-P, and macro and micro-elements. Results and Discussion Except for the soils amended with CaCl₂, or CaCl₂+CaCO₃, reactive P and PO₄-P leaching losses mainly occurred in the first three leaching events. Phosphorus leaching from the soils amended with CaCl₂ or CaCl₂+CaCO₃ was less but more persistent than that of other amendments. Reactive Pleaching loss was reduced by 36.0% and 40.4% for the amendments of CaCl₂, and CaCl₂+CaCO₃, respectively, as compared with chemical fertilizer alone, and the corresponding values for PO₄-P were 70.8% and 71.9%. The concentrations of K, Mg, Cu, and Fe in leachate were also decreased by CaCl₂ or CaCl₂+CaCO₃ amendment. Among the seven amendments, CaCl₂, CaCO₃, or their combination were most effective in reducing P leaching from the sandy soil, followed by cellulose and Al(OH)₃, the effects of mill mud and mill mud + Al(OH)₃ were marginal. Conclusions These results indicate that the use of CaCl₂, CaCO₃, or their combination can significantly reduce P leaching from sandy soil, and should be considered in the development of BMPs for the sandy soil regions. Recommendations and Outlook Most agricultural soils in south Florida are very sandy with minimal holding capacities for moisture and nutrients. Repeated application of fertilizer is necessary to sustain desired yield of crops on these soils. However, eutrophication of fresh water systems in this area has been increasingly concerned by the public. Losses of P from agricultural fields by means of leaching and surface runoff are suspected as one of the important non-point contamination sources. The benefits and effectiveness of soil amendment in reducing P losses from cropping production systems while sustaining desired crop yield need to be demonstrated. Calcium chloride, CaCO₃, or their combination significantly reduce Pleaching from sandy soil, and should be considered in the development of BMPs for the sandy soil regions.     

Herbicide movement and dissipation at four midwestern sites

Abstract

This study was conducted to evaluate atrazine (2‐chloro‐4‐ethylamino‐6‐isopropyl‐1, 3, 5‐triazine) and alachlor (2‐chIoro‐N‐(methoxymethyl)acetamide) dissipation and movement to shallow aquifers across the Northern Sand Plains region of the United States. Sites were located at Minnesota on a Zimmerman fine sand, North Dakota on Hecla sandy loam, South Dakota on a Brandt silty clay loam, and Wisconsin on a Sparta sand. Herbicide concentrations were determined in soil samples taken to 90 cm four times during the growing season and water samples taken from the top one m of aquifer at least once every three months. Herbicides were detected to a depth of 30 cm in Sparta sand and 90 cm in all other soils. Some aquifer samples from each site contained atrazine with the highest concentration in the aquifer beneath the Sparta sand (1.28 μg L^‐1). Alachlor was detected only once in the aquifer at the SD site. The time to 50% atrazine dissipation (DT₅₀) in the top 15 cm of soil averaged about 21 d in Sparta and Zimmerman sands and more than 45 d for Brandt and Hecla soils. Atrazine DT₅₀ was correlated positively with % clay and organic carbon (OC), and negatively with % fine sand. Alachlor DT₅₀ ranged from 12 to 32 d for Zimmerman and Brandt soils, respectively, and was correlated negatively with % clay and OC and positively with % sand.     

Books available

Abstract

The leaching behaviour of the herbicide acetochlor [2‐chloro‐N‐(2‐ethyl‐6‐methylphenyl)‐N‐(ethoxymethyl)acetamide] was determined as compared with two congener compounds, alachlor [2‐chloro‐N‐(2,6‐diethylphenyl)‐N‐(methoxymethyl)acetamide] and metolachlor [2‐chloro‐N‐(2‐ethyl‐6‐methylphenyl)‐N‐(2‐methoxy‐l‐methylethyl)acetamide]. The leaching profiles of the herbicides in columns with different types of soil and their capacity factors in reverse phase HPLC were compared. An approach for preliminary characteristic of the potential for water pollution of acetochlor is presented. The herbicide is classified as a leacher in soil and its potential for contamination of ground water is comparable with those of alachlor and metolachlor.     

Deposition and adsorption of the air pollutant HNO3 vapor to soil surfaces

Deposition of nitric acid (HNO₃) vapor to soils has been evaluated in three experimental settings: (1) continuously stirred tank reactors with the pollutant added to clean air, (2) open-top chambers at high ambient levels of pollution with and without filtration reducing particulate nitrate levels, (3) two field sites with high or low pollution loads in the coastal sage plant community of southern California. The results from experiment (1) indicated that the amount of extractable NO₃⁻ from isolated sand, silt and clay fractions increased with atmospheric concentration and duration of exposure. After 32 days, the highest absorption of HNO₃ was determined for clay, followed by silt and sand. While the sand and silt fractions showed a tendency to saturate, the clay samples did not after 32 days of exposure under highly polluted conditions. Absorption of HNO₃ occurred mainly in the top 1 mm layer of the soil samples and the presence of water increased HNO₃ absorption by about 2-fold. Experiment (2) indicated that the presence of coarse particulate NO₃⁻ could effectively block absorption sites of soils for HNO₃ vapor. Experiment (3) showed that soil samples collected from open sites had about 2.5 more extractable NO₃⁻ as compared to samples collected from beneath shrub canopies. The difference in NO₃⁻ occurred only in the upper 1–2 cm as no significant differences in NO₃⁻ concentrations were found in the 2–5 cm soil layers. Extractable NO₃⁻ from surface soils collected from a low-pollution site ranged between 1 and 8 μg NO₃–N g⁻¹, compared to a maximum of 42 μg NO₃–N g⁻¹ for soils collected from a highly polluted site. Highly significant relationship between HNO₃ vapor doses and its accumulation in the upper layers of soils indicates that carefully prepared soil samples (especially clay fraction) may be useful as passive samplers for evaluation of ambient concentrations of HNO₃ vapor.     

Persistence of metsulfuron‐methyl in two soils

Abstract

The persistence of metsulfuron‐methyl in sandy loam and clay soil incubated at different temperatures and moistures contents was investigated under laboratory conditions using longbean (Vigna sesquipedalis L.) as bioassay species. A significant degradation of metsulfuron‐methyl was observed in non‐autoclaved soil rather than the autoclaved soil sample. At higher temperature, the degradation rate in non‐autoclaved soil improved with increasing soil moisture content. In non‐autoclaved sandy loam and clay soil, the half‐life was reduced from 9.0 to 5.7 and from 11.2 to 4.6 days, respectively when moisture level of sandy loam increased from 20 to 80% field capacity at 35°C. In the autoclaved soil, herbicide residue seems to have been broken down by non‐biological process. The rate of dissipation was slightly increased after the second application of the herbicide to non‐autoclaved soils but not in autoclaved soil, indicating the importance of microorganisms in the breakdown process.     

Aminocyclopyrachlor sorption-desorption and leaching from three Brazilian soils

This study aimed to evaluate the sorption-desorption and leaching of aminocyclopyrachlor from three Brazilian soils. The sorption-desorption of ¹⁴C-aminocyclopyrachlor was evaluated using the batch method and leaching was assessed in glass columns. The Freundlich model showed an adequate fit for the sorption-desorption of aminocyclopyrachlor. The Freundlich sorption coefficient [K_{f (sorption)}] ranged from 0.37 to 1.34 µmol ^(1–1/n) L^1/n kg^?1 and showed a significant positive correlation with the clay content of the soil, while the K_{f (desorption)} ranged from 3.62 to 5.36 µmol ^(1–1/n) L^1/n kg^?1. The K_{f (desorption)} values were higher than their respective K_{f (sorption)}, indicating that aminocyclopyrachlor sorption is reversible, and the fate of this herbicide in the environment can be affected by leaching. Aminocyclopyrachlor was detected at all depths (0?30 cm) in all the studied soils, where leaching was influenced by soil texture. The total herbicide leaching from the sandy clay and clay soils was <0.06%, whereas, ～3% leached from the loamy sand soil. The results suggest that aminocyclopyrachlor has a high potential of leaching, based on its low sorption and high desorption capacities. Therefore, this herbicide can easily contaminate underground water resources.