High-performance liquid chromatography (HPLC) as a tool for monitoring the fate of fluazinam in soil

Fluazinam is a widely used pesticide employed against the fungal disease late blight in potato cultivation. A specific, repeatable, and rapid high-performance liquid chromatography (HPLC) method utilizing a diode array detector (DAD) was developed to determine the presence of fluazinam in soil. The method consists of acetonitrile (ACN) extraction, clean-up with solid-phase extraction (SPE), and separation using a mobile phase consisting of 70% ACN and 30% water (v/v), including 0.02% acetic acid. HPLC was performed with a C18 column and the detection wavelength was 240 nm. The method was successfully applied to an incubation experiment and to soil samples taken from potato fields where fluazinam had been applied two to three times during the on-going growing season. In the 90-day incubation experiment, analytical standard fluazinam and the commercial fungicide Shirlan^® were added to soil samples that had never been treated with fluazinam, and were then extracted with ACN and 0.01 M calcium chloride (CaCl₂). Fluazinam was not extractable with CaCl₂, indicating that it does not leach to watercourses in the dissolved form. Recovery with ACN extraction for sandy soils was 72–95% immediately after application and 53–73% after 90 days of incubation. Out of the eight potato field soil samples, fluazinam was found in two samples at concentrations of 2.1 mg kg^?1 and 1.9 mg kg^?1, well above the limit of quantification (0.1 mg kg^?1).     

Determination of organochlorine and organophosphorus pesticide residues in low moisture,nonfatty products using a solid phase extraction cleanup and gas chromatography

Abstract

A multiresidue solid‐phase extraction (SPE) method for the isolation and subsequent gas Chromatographie determination of organochlorine and organophosphorus pesticide residues in low‐moisture, nonfatty products is described. Residues are extracted from samples with an acetonitrile/water mixture. Cleanup of the extract is performed using graphitized carbon black and anion exchange SPE columns, and analysis is performed by gas chromatography with Hall electrolytic conductivity and flame photometric detection. Recovery data was obtained by fortifying corn, oats and wheat with pesticides. The average recoveries were 79–123% for eight organochlorine and 51–122% for 28 organophosphorus pesticide residues. The limit of quantitation for chlorpyriphos was 0.05 ppm using the Hall electrolytic conductivity detector and <0.005 ppm using the flame photometric detector.     

The effect of acute administration of the mycotoxin zearalenone to female pigs∗

Abstract

Crystalline zearalenone was administered to young female pigs at dose levels of 0, 3.5, 7.5 and 11.5 mg zearalenone/kg body weight. All animals receiving the mycotoxin exhibited vulva vag‐initis and had enlarged reproductive tracts, 1 week after dosing. Free zearalenone was found in the blood, feces and urine of dosed animals. The highest zearalenone level detected was 2.61 ng/ml from a pig that received the 7.5 mg/kg dose. After 24 hours, feces collected contained on average up to 308 ng zearalenone per g of dried feces. Zearalenone levels of up to 59 ng/ml, and a ‐zearalenol levels of up to 155 ng/ml urine were found. ß ‐zearalenol was also detected in the urine.     

Pyrimethanil Residues on Table Grapes Italia after Field Treatment

Residues of the pyrimidine fungicide pyrimethanil [N-(4,6-dimethylpyrimidin-2yl)aniline] were determined in table grapes “Italia” by gas chromatography nitrogen-phosphorus detector (GC-NPD). Pesticides were extracted from grapes with ethyl acetate and hexane solution (1:1 v/v), and were analyzed without any further clean up. Pyrimethanil was confirmed by high-performance liquid chromatography (HPLC) fitted with a diode array detector (DAD) and electrospray ionization mass spectrometry (ESI-MS) in the select ion-monitoring mode (SIM). The residue of pyrimethanil was under the legal limit immediately after treatment, and showed a half-life time, calculated as a reaction of pseudo first order, of 12 days, with a regression coefficient of 0.9954. Recoveries from fortified grapes ranged between 90 and 113% with a maximum coefficient of variation (CV) of 11%. The calculated limits of detection and quantitation for pyrimethanil were 0.005 and 0.01 mg/kg, respectively.     

Deactivation of mycotoxins. I. An in vitro study of zearalenone adsorption on new polymeric adsorbents

Abstract

This study describes the elimination of zearalenone concentrations in vitro using two new polymeric forms of cross‐linked polyvinylpyrrolidone (cryogels of cross‐linked PVP). Adsorption of zearalenone was studied under isothermal conditions and simulating pH of intestinal environment. A Freundlich isotherm was used to describe the adsorption data obtained. The results showed significant decrease of zearalenone concentrations, ranging from 33.5–66.2 % per 25 mg of polymer. Adsorption capacity (k) was estimated to be higher than that of previously tested adsorbents, including crospovidone. The data indicate the need to investigate structure peculiarities in order to improve mycotoxin deactivation procedures using PVP derivatives.     

Development of an analytical method for analysis of flubendiamide,des-iodo flubendiamide and study of their residue persistence in tomato and soil

Flubendiamide is a new insecticide that has been found to give excellent control of lepidopterous pests of tomato. This study has been undertaken to develop an improved method for analysis of flubendiamide and its metabolite des-iodo flubendiamide and determine residue retention in tomato and soil. The analytical method developed involved extraction of flubendiamide and its metabolite des-iodo flubendiamide with acetonitrile, liquid-liquid partitioning into hexane-ethyl acetate mixture (6:4, v v^?1) and cleanup with activated neutral alumina. Finally the residues were dissolved in gradient high pressure liquid chromatography (HPLC) grade acetonitrile for analysis by HPLC. The mobile phase, acetonitrile-water at 60:40 (v v^?1) proportion and the wavelength of 235 nm gave maximum peak resolution. Using the above method and HPLC parameters described, nearly 100 % recovery of both insecticides were obtained. There was no matrix interference and the limit of quantification (LOQ) of the method was 0.01 mg kg^?1. Initial residue deposits of flubendiamide on field-treated tomato from treatments @ 48 and 96 g active ingredient hectare^?1 were 0.83 and 1.68 mg kg^?1,respectively. The residues of flubendiamide dissipated at the half-life of 3.9 and 4.4 days from treatments @ 48 and 96 g a.i. ha^?1, respectively and persisted for 15 days from both the treatments. Des-iodo flubendiamide was not detected in tomato fruits at any time during the study period. Residues of flubendiamide and des-iodo flubendiamide in soil from treatment @ 48 and 96 g a.i. ha^?1 were below detectable level (BDL, < 0.01 mg kg^?1) after 20 days. Flubendiamide completely dissipated from tomato within 20 days when the 480 SC formulation was applied at doses recommended for protection against lepidopterous pests.     

Rapid determination of trace dicyandiamide in mussels from Zhejiang coast by ultra-fast liquid chromatography–tandem mass spectrometry with isotope internal standard dilution technique

In this study, a rapid and accurate ultra-fast liquid chromatography–tandem quadrupole mass spectrometry (UFLC–MS/MS) method coupled with the isotope internal standard dilution technique was established and validated to determine trace dicyandiamide (DCD) in mussels. The sample was extracted by acetonitrile, and chromatographic separations were performed on an Acquity UPLC BEH Amide column by using water–acetonitrile (9:91, v/v) as the mobile phase within 3 min. DCD was determined by using DCD-¹⁵N₄ as an internal standard. The results showed that the recoveries were between 96.2 and 103 % with relative standard deviations (RSDs) in the range of 0.6–6.0 %. The limit of quantification (LOQ) was 0.05 μg/kg. This method can be applied to the routine analysis for the rapid and sensitive determination of trace DCD in mussels. Overall, the data reiterate the importance of investigating the presence of DCD in marine biological samples, which can act as food quality controls for human health.     

High performance liquid chromatographic method for residue determination of sulfosulfuron

A method was developed for sulfosulfuron [(1-(2-ethylsulfonylimidazo [1,2-a] pyridin-3-ylsulfonyl)-3-(4,6-dimethoxy pyrimidin-2yl)] and its three major metabolites by HPLC utilizing photodiode array detector. The method makes use of Lichrosphere RP-8 column and acetonitrile:water:orthophosphoric acid (80:20:0.1 v/v/v) as mobile phase at a flow rate of 1 ml min(-1). Using these condition sulfosulfuron, and compounds II, III and IV were resolved with distinct Rt of 2.088, 2.216, 2.302 and 2.476 minutes, respectively. Sulfosulfuron residues were analysed in soil, wheat grain and straw samples by extracting with a mixture of acetonitrile and 2 M ammonium carbonate (100 ml, 9:1, v/v) using horizontal shaker for soil and Soxhlet apparatus for wheat grain and straw samples. The extracts were cleaned up by partitioning with dichloromethane in case of soil and hexane followed by dichloromethane for plant samples. The percent recovery ranged between 71 to 75.2 for soil and 70.8 to 74.7 for plant samples. The limit of determination of sulfosulfuron was 0.25 microg g(-1).     

Residues and dissipation kinetic of abamectin,chlorfenapyr and pyridaben acaricides in green beans (Phaseolus vulgaris L.) under field conditions using QuEChERS method and HPLC

Abstract

The current study estimated the dissipation rates of abamectin, chlorfenapyr and pyridaben acaricides in pods of green beans (Phaseolus vulgaris L.) under field conditions in Egypt. Pesticides were extracted and cleaned-up by QuEChERS method and were analyzed by HPLC. The dissipation of these acaricides followed the first order kinetics model with half-life (t_1/2) values 1.00, 3.50 and 1.50?days for abamectin, chlorfenapyr and pyridaben, respectively. The lowest residues, at different time intervals of field application rate of each pesticide, were observed with abamectin followed by pyridaben and then chlorfenapyr. Pre-harvest intervals (PHIs) were 10.00, 13.50 and 6.00?days for abamectin, chlorfenapyr and pyridaben, respectively and were below the established European maximum residue limits (EU MRLs) 10–14, 14–21 and 7–10?days after application, respectively. If the fresh pods will be consumed after harvest, it is expected that the presence of these pesticides in the food will have a negative impact on human health. Therefore, the elimination of the residues of these harmful pesticides must be carried out.     

Determination of fumonisins in milk

Abstract

Fumonisin B₁ (FB₁) and fumonisin B₂ (FB₂) were determined in milk by liquid chromatography (LC) following immunoaffinity column cleanup. Recoveries from milk spiked with 5–50 ng each fumonisin/ml averaged 79–109%. The aminopentol hydrolysis product of FB₁ (AP₁) was determined by LC after cleanup on a C₁₈solid phase phase extraction column; mean recoveries were 69–83% at spiking levels of 50–100 ng AP₁/ml milk. Detection limits were of the order 3–7 ng/ml for FB₁ and FB₂, and 20–25 ng/ml for AP₁. A stability study showed no losses of FB₁ and FB₂ in milk under conditions of freezing, refrigeration and boiling. A transmission study using four cows dosed with pure FB₁, either orally (1.0 and 5.0 mg FB₁/kg b.w.) or by i.v. injection (0.05 and 0.20 mg FB₁/kg b.w.) showed no detectable residues of FB, or AP₁ in the milk, with or without hydroiytic treatment with β‐glucuronidase/sulfatase to liberate any conjugates.     

Development of an analytical method for analysis of flubendiamide, des-iodo flubendiamide and study of their residue persistence in tomato and soil

Flubendiamide is a new insecticide that has been found to give excellent control of lepidopterous pests of tomato. This study has been undertaken to develop an improved method for analysis of flubendiamide and its metabolite des-iodo flubendiamide and determine residue retention in tomato and soil. The analytical method developed involved extraction of flubendiamide and its metabolite des-iodo flubendiamide with acetonitrile, liquid-liquid partitioning into hexane-ethyl acetate mixture (6:4, v v?1) and cleanup with activated neutral alumina. Finally the residues were dissolved in gradient high pressure liquid chromatography (HPLC) grade acetonitrile for analysis by HPLC. The mobile phase, acetonitrile-water at 60:40 (v v?1) proportion and the wavelength of 235 nm gave maximum peak resolution. Using the above method and HPLC parameters described, nearly 100 % recovery of both insecticides were obtained. There was no matrix interference and the limit of quantification (LOQ) of the method was 0.01 mg kg?1. Initial residue deposits of flubendiamide on field-treated tomato from treatments @ 48 and 96 g active ingredient hectare?1 were 0.83 and 1.68 mg kg?1, respectively. The residues of flubendiamide dissipated at the half-life of 3.9 and 4.4 days from treatments @ 48 and 96 g a.i. ha?1, respectively and persisted for 15 days from both the treatments. Des-iodo flubendiamide was not detected in tomato fruits at any time during the study period. Residues of flubendiamide and des-iodo flubendiamide in soil from treatment @ 48 and 96 g a.i. ha?1 were below detectable level (BDL, < 0.01 mg kg?1) after 20 days. Flubendiamide completely dissipated from tomato within 20 days when the 480 SC formulation was applied at doses recommended for protection against lepidopterous pests.     

Quantitative analysis of acetamiprid and imidacloprid residues in tomato fruits under greenhouse conditions

Abstract

A selective liquid chromatographic analytical method was studied for determination of two neonicotinoids, acetamiprid and imidacloprid, in tomato fruits under greenhouse conditions in Egypt. The fruits were extracted and cleaned up by QuEChERS method followed by HPLC determination. The method showed a good linearity with a determination coefficient (R²) of higher than 0.99 for the 0.0125–0.15 µg/mL concentration range. The method was validated using a blank tomato spiked at 5, 25 and 50 mg/kg and the recovery percentages were 83.71, 94.52 and 97.49% for acetamiprid and 88.59, 89.63 and 90.18% for imidacloprid, respectively. The rates of dissipation of both pesticides were studied and the preharvest intervals (PHIs) were calculated. Imidacloprid dissipated faster than acetamiprid and half-life periods were 1.30 and 2.07 days, respectively. Acetamiprid and imidacloprid residues were below the already established European maximum residue limits (EU MRLs) (0.5 mg/kg) 3 and 5 days after application, respectively.     

Rapid screening for organochlorine and organophosphorus pesticides in milk using C18 and graphitized carbon black solid phase extraction cleanup

Abstract

A rapid, multiresidue, solid phase extraction (SPE) technique for the isolation and gas chromatographic determination of organochlorine and moderately polar organophosphorus pesticide residues in milk is described. Milk is sonicated with an acetonitrile‐acetone‐methanol mixture and centrifuged. The supernatant is subjected to a cleanup using both C₁₈ and graphitized carbon black SPE columns. The pesticide residues are determined by gas chromatography with electron capture and flame photometric detection. The method required minimal volumes of solvent and resulted in the production of minimal volumes of hazardous waste.     

Evaluation of Beta‐naphthoxyacetic Acid for Mutagenic Activity in the Salmonella/mammalian Microsome Assay

1,3‐β‐d‐Glucan derived from baker's yeast was chemically modified in two steps yielding crosslinked carboxymethyl glucan as the sodium salt (2). After cation exchange with hexadecyltrimethylammonium chloride, a hydrophobic adsorbent (3) was obtained which showed an excellent binding of the estrogenic mycotoxin zearalenone with a maximum adsorption of up to 183 mg/g. Compound 3 additionally showed a relatively high adsorption capacity for the trichothecene T‐2 toxin of at least 10 mg/g. Starting from 2, various derivatives were prepared by cation exchange using quaternary ammonium salts bearing substituents besides methyl from four to 18 carbon atoms. The adsorption of T‐2 toxin on these derivatives were compared with compound 3 leading to the conclusion that 3 is the best adsorbent of all investigated tetraalkylammonium‐modified derivatives of 2.     

A simple HPLC method for determination of permethrin residues in wine

An isocratic High Performance Liquid Chromatographic (HPLC) method was optimized for 3-phenoxybenzyl (1RS)-cis-trans-3-(2,2-dichlorovinyl)-2,2-dimethyl-cyclopropanecarboxylate (permethrin) residues identification and quantification in wine matrix. Analytical reverse phase (RP) C-18 column was used (25 cm × 4 mm i.d., 5 μ m) with mobile phase consisting of acetonitrile and water in ratio 70 %/30 % (v v^?1), flow-rate 2.0 mL min^?1, UV-detection at 215 nm and controlled oven temperature at 25°C. The peaks of isomers were identified with the retention times as compared to standard cis-/trans- mixture and confirmed with characteristic spectra using photodiode array detector. Under these conditions, permethrin isomers were well separated with resolution 2.8 and no interference with the naturally present wine compounds was observed. The method was validated for linearity, precision, accuracy, limit of detection (LOD) and limit of quantification (LOQ). Linear regression analysis data proved a good linear relationship (correlation coefficients, r², for cis- and trans-isomer are: 0.9995 and 0.9997, respectively) between response of the detector and concentration of permethrin isomers over a wide concentration range for both isomers (0.55 mg L^?1 ?4.40 mg L^?1). Experimental data showed mean recoveries between 93.95% and 96.58% with RSD values in range: 0.89% ?3.69%. The effect of ethanol content in the solvent on permethrin isomers peak areas was also studied and 60% v v^?1 ethanol was found to be optimal for sample preparation. The method was successfully tested on 20 commercial wine samples from the market in which no permethrin was detected. Thus, it was proved that it is suitable for routine permethrin residues analysis. The proposed method is suitable for routine analysis because of the simple sample preparation, acceptable run-time, low cost and its applicability with conventional instruments.     

Determination of 2,4-Dichlorophenoxyacetic acid in food and water samples using a modified graphene oxide sorbent and high-performance liquid chromatography

Abstract

In the present work, dispersive micro-solid phase extraction (D-μ-SPE) method using magnetic graphene oxide tert-butylamine (GO/Fe₃O₄/TBA) nanocomposite, as an efficient sorbent, was applied for determining 2,4-dichlorophenoxyacetic acid (2,4-D) in water and food samples. Detection was carried out using high-performance liquid chromatography (HPLC) instrument. Influential parameters of D-μ-SPE such as sorbent and its amount, elution solvent and its volume, adsorption and desorption times and pH of sample solution were investigated and optimized. Under the optimized conditions, limit of detection and quantitation values were 0.007 and 0.02?μg/mL, respectively. Recovery data for several real samples were obtained within the range of 88.0–94.0% with a relative standard deviation (RSD) less than 7.5%. The proposed method was successfully applied to quantitative determination of 2,4-D in several vegetables and water samples.     

Metabolism of the Nonylphenol Isomer [Ring-U-14c]-4-(3′,5′-Dimethyl-3′-Heptyl)-Phenol by Cell Suspension Cultures of Agrostemma githago and Soybean

Abstract

The biotransformation of the nonylphenol isomer [ring-U-¹⁴C]-4-(3′,5′-dimethyl-3′-heptyl)-phenol (4-353-NP, consisting of two diastereomers) was studied in soybean and Agrostemma githago cell suspension cultures. With the A. githago cells, a batch two-liquid-phase system (medium/n-hexadecane 200:1, v/v) was used, in order to produce higher concentrations and amounts of 4-353-NP metabolites for their identification; 4-353-NP was applied via the n-hexadecane phase. Initial concentrations of [¹⁴C]-4-353-NP were 1 mg L^?1 (soybean), and 5 and 10 mg L^?1 (A. githago). After 2 (soybean) and 7 days (A. githago) of incubation, the applied 4-353-NP was transformed almost completely by both plant species to four types of products: glycosides of parent 4-353-NP, glycosides of primary 4-353-NP metabolites, nonextractable residues and unknown, possibly polymeric materials detected in the media. The latter two products emerged especially in soybean cultures. Portions of primary metabolites amounted to 19–22% (soybean) and 21–42% of applied ¹⁴C (A. githago). After liberation from their glycosides, the primary 4-353-NP metabolites formed by A. githago were isolated by HPLC and examined by GC-EIMS as trimethylsilyl derivatives. In the chromatograms, eight peaks were detected which due to their mass spectra, could be traced back to 4-353-NP. Seven of the compounds were side-chain monohydroxylated 4-353-NP metabolites, while the remaining was a (side-chain) carboxylic acid derivative. Unequivocal identification of the sites of hydroxylation/oxidation of all transformation products was not possible. The main primary metabolites produced by A. githago were supposed to be four diastereomers of 6′-hydroxy-4-353-NP (about 80% of all products identified). It was concluded that plants contribute to the environmental degradation of the xenoestrogen nonylphenol; the toxicological properties of side-chain hydroxylated nonylphenols remain to be examined.     

Soil Persistence of Triasulfuron Herbicide as Affected by Biotic and Abiotic Factors

Persistence of triasulfuron [3-(6-methoxy-4methyl-1,3,5-triazin-2-yl)-1-{2-(2-chloroethoxy)-phenylsulfonyl}-urea] in soil was studied under wheat crop and laboratory conditions. Field experiment was conducted in the farms of Agronomy Division, Indian Agricultural Research Institute (IARI), New Delhi. Randomized block design (RBD) was followed with four replicates and two rates of treatments along with control and weedy check. Triasulfuron was applied as post-emergent application to wheat crop at two rates of application viz., 15 g and 20 g a.i. ha^?1. Soil samples at 0 (3 h), 1, 3, 5, 7, 10, 15, 20, and 30-day intervals after application were drawn, extracted, cleaned up, and analyzed for herbicide residues by high performance liquid chromatography (HPLC) using C₁₈ column and methanol: water (8:2) as mobile phase at 242 nm wave length. Effect of microbial activity and soil pH was studied under laboratory conditions. Dissipation of triasulfuron followed a first-order-rate kinetics. Residues dissipated from field soil with half-life of 5.8 and 5.9 days at two rates of application. The study indicated biphasic degradation with faster rate initially (t _1/2 = 3.7 days), followed by a slower dissipation rate at the end (t _1/2 = 9.4 days). Similar trend was observed with non-sterile soil in laboratory with a longer half-life. Acidic pH and microbial activity contributed toward the degradation of triasulfuron in soil.     

Direct determination of neonicotinoid insecticides in an analytically challenging crop such as Chinese chives using selective ELISAs

ABSTRACT

Easy-to-use commercial kit-based enzyme-linked immunosorbent assays (ELISAs) have been used to detect neonicotinoid dinotefuran, clothianidin and imidacloprid in Chinese chives, which are considered a troublesome matrix for chromatographic techniques. Based on their high water solubility, water was used as an extractant. Matrix interference could be avoided substantially just diluting sample extracts. Average recoveries of insecticides from spiked samples were 85–113%, with relative standard deviation of <15%. The concentrations of insecticides detected from the spiked samples with the proposed ELISA methods correlated well with those by the reference high-performance liquid chromatography (HPLC) method. The residues analyzed by the ELISA methods were consistently 1.24 times that found by the HPLC method, attributable to loss of analyte during sample clean-up for HPLC analyses. It was revealed that the ELISA methods can be applied easily to pesticide residue analysis in troublesome matrix such as Chinese chives.     

Simultaneous Determination of Imidacloprid,Thiacloprid, and Thiamethoxam in Soil and Water by High-performance Liquid Chromatography with Diode-array Detection

Abstract

A high-performance liquid chromatography method with diode-array detection (HPLC-DAD) is described for the determination of three neonicotinoid insecticides imidacloprid, thiacloprid, and thiamethoxam in soil and water. The soil samples were extracted with acetonitrile, while the water samples were extracted using C₁₈ cartridges. The mean recoveries plus standard deviations for spiked soil samples were 82 ± 4.2% for thiamethoxam, 99 ± 4.2% for imidacloprid and 94 ± 1.4% for thiacloprid. The recoveries for water samples ranged from 87 ± 3.4% for thiamethoxam to 97 ± 3.9% for imidacloprid and 97 ± 2.6% for thiacloprid. The limits of quantitation (LOQ) were 0.1, 0.1, 0.01 mg/kg in soil (5 g), and 2, 2, 0.5 µg/L in water (50 mL) for thiamethoxam, imidacloprid, and thiacloprid, respectively.