Observations Less than the Analytical Limit of Detection: A New Approach

Abstract

Solutions are given for plume rise assuming a power-law wind speed profile in a stably stratified layer for point and finite sources with initial vertical momentum and buoyancy. For a constant wind speed, these solutions simplify to the conventional plume rise equations in a stable atmosphere. In a shear layer, the point of maximum rise occurs further downwind and is slightly lower compared with the plume rise with a constant wind speed equal to the wind speed at the top of the stack. If the predictions with shear are compared with predictions for an equivalent average wind speed over the depth of the plume, the plume rise with shear is higher than plume rise with an equivalent average wind speed.     

Design and Verification of a Programmable Gas Dispensing System for Exposing Plants to Dynamic Concentrations of Air Pollutants

Abstract

Landfills represent a source of distributed emissions source over an irregular and heterogeneous surface. In the method termed “Other Test Method-10” (OTM-10), the U.S. Environmental Protection Agency (EPA) has proposed a method to quantify emissions from such sources by the use of vertical radial plume mapping (VRPM) techniques combined with measurement of wind speed to determine the average emission flux per unit area per time from nonpoint sources. In such application, the VRPM is used as a tool to estimate the mass of the gas of interest crossing a vertical plane. This estimation is done by fitting the field-measured concentration spatial data to a Gaussian or some other distribution to define a plume crossing the vertical plane. When this technique is applied to landfill surfaces, the VRPM plane may be within the emitting source area itself. The objective of this study was to investigate uncertainties associated with using OTM-10 for landfills. The spatial variability of emission in the emitting domain can lead to uncertainties of –34 to 190% in the measured flux value when idealistic scenarios were simulated. The level of uncertainty might be higher when the number and locations of emitting sources are not known (typical field conditions). The level of uncertainty can be reduced by improving the layout of the VRPM plane in the field in accordance with an initial survey of the emission patterns. The change in wind direction during an OTM-10 testing setup can introduce an uncertainty of 20% of the measured flux value. This study also provides estimates of the area contributing to flux (ACF) to be used in conjunction with OTM-10 procedures. The estimate of ACF is a function of the atmospheric stability class and has an uncertainty of 10–30%.     

Study of particulates and metallic elements at a farm sampling site in central Taiwan

The total suspended particle (TSP) concentration, dry deposition and wind speed were measured with a PS-1 sampler, a dry deposition plate and a Weather Monitor II (#7440), respectively, at the Experimental Farm of Thunghai University in Taiwan. Taiching Industrial Park, Taichung Cong Road (traffic) and a hospital incinerator are close to the sampling site. The sampling time was from August 2001 to December 2001. The average dry deposition flux, the TSP concentration, dry deposition velocities, average wind speed and maximum wind speed were recorded as 617.7 ± 281.4 mg/day/m2, 117.5 ± 17.6 μg/m3, 5.9 ± 2.2 cm/s, 2.7 ± 1.3 m/s and 7.6 ± 2.3 m/s, respectively, at this sampling site. Good correlation coefficients (R) of the TSP concentration and the dry deposition flux with wind speed were found, with values of 0.46 and 0.50, respectively. The concentrations and dry deposition of the total metallic elements were also obtained. The results indicated that the concentrations of anthropogenic elements (Pb, Mn, Cd, Ni, Cr and Zn) were mostly higher than those obtained in other studies around the world. The average dry deposition fluxes and TSP concentrations for Zn and Pb were 0.45 and 0.42, respectively. The same phenomenon was also observed for Fe and Mg (R = 0.59 and 0.65). The results indicate that these elements were all coming from the same emission sources at the farm sampling site.     

Intercalibration of a passive wind-vane flux sampler against a continuous-flow denuder for the measurements of atmospheric ammonia concentrations and surface exchange fluxes

A passive wind-vane flux sampler is a simple low-cost device used to estimate long-term vertical fluxes of ammonia in the atmospheric surface boundary layer. The passive flux sampler measures the horizontal flux of ammonia. A vertical gradient of the horizontal flux, combined with micro-meteorological measurements of wind speed and temperature, is used to estimated the vertical flux of ammonia using a modified aerodynamic gradient technique. The passive wind-vane flux sampler gradient was calibrated against a gradient measured with fast response (6 min) continuous-flow denuders. The measurements were carried out at a heathland located in an intensive farming area in the centre of the Netherlands. A field campaign took place over 70 day period in the summer of 1996, during which the sampling periods of the passive wind-vane flux sampler varied between 3 and 9 days. The comparison clearly showed that the long-term measurements with the passive wind-vane flux samplers gave accurate average ammonia deposition values for the field campaign as a whole which deviated by only 18% from the reference flux. However, there was no significant correlation between the fluxes from the passive samplers and the reference method for the individual 10 periods which were compared. Possible explanations found for the lacking correlation were (I) a high percentage number of half-hour emission events within each period resulted in a significant large relative deviation between the fluxes, and (II) uncertainties in the reference method might also explain the lacking correlation. The passive wind-vane flux samplers proved to be a stable method for long-term measurements (months to years) due to a close to 100% optimal functioning during the field campaign.     

Theoretical and Observational Assessments of Flare Efficiencies

ABSTRACT

Flaring of waste gases is a common practice in the processing of hydrocarbon (HC) materials. It is assumed that flaring achieves complete combustion with relatively innocuous byproducts such as CO₂ and H₂O. However, flaring is rarely successful in the attainment of complete combustion, because entrainment of air into the region of combusting gases restricts flame sizes to less than optimum values. The resulting flames are too small to dissipate the amount of heat associated with 100% combustion efficiency.

Equations were employed to estimate flame lengths, areas, and volumes as functions of flare stack exit velocity, stoichiometric mixing ratio, and wind speed. Heats released as part of the combustion process were then estimated from a knowledge of the flame dimensions together with an assumed flame temperature of 1200 K. Combustion efficiencies were subsequently obtained by taking the ratio of estimated actual heat release values to those associated with 100% complete combustion.

Results of the calculations showed that combustion efficiencies decreased rapidly as wind speed increased from 1 to 6 m/sec. As wind speeds increased beyond 6 m/sec,combustion efficiencies tended to level off at values between 10 and 15%. Propane and ethane tend to burn more efficiently than do methane or hydrogen sulfide because of their lower stoichiometric mixing ratios.

Results of theoretical predictions were compared to nine values of local combustion efficiencies obtained as part of an observational study into flaring activity conducted by the Alberta Research Council (ARC). All values were obtained during wind speed conditions of less than 4 m/sec. There was generally good agreement between predicted and observed values. The mean and standard deviation of observed combustion efficiencies were 68 ± 7%. Comparable predicted values were 69 ± 7%.     

Atmospheric deposition of polycyclic aromatic hydrocarbons to water surfaces: A mass balance approach

A mass balance model was developed to explain the movement of polycyclic aromatic hydrocarbons (PAH) into and out of Siskiwit Lake, which is located on a wilderness island in northern Lake Superior. Because of its location, the PAH found in this lake must have originated exclusively from atmospheric sources. Using gas Chromatographie mass spectrometry, 11 PAH were quantified in rain, snow, air, lake water, sediment core and sediment trap samples. From the dry deposition fluxes, an aerosol deposition velocity of 0.99 ± 0.15 cm s⁻¹ was calculated for indeno[1,2,3-cd]pyrene and benzo[ghi]perylene, two high molecular weight PAH which are not found in the gas phase. The dry aerosol deposition was found to dominate the wet removal mechanism by an average ratio of 9:1. The dry gas flux was negative, indicating that surface volatilization was taking place; it accounted for 10–80 % of the total output flux depending on the volatility of the PAH. The remaining PAH were lost to sedimentation. From the dry gas flux, an overall mass transfer coefficient for PAH was calculated to be 0.18 ± 0.06 m d⁻¹. In this case, the overall mass transfer is dominated by the liquid phase resistance.     

Sedimentation and seasonal variation of hexachlorocyclohexanes in sediments in a eutrophic lake,China

Hexachlorocyclohexane (HCH) concentrations in sediments and sediment trap fluxes of particulate organic carbon and HCHs were measured bi-weekly from March 31 to October 18, 2006 in an urban eutrophic lake in Tianjin, China, in order to investigate sedimentation and seasonal variation of HCHs in sediments. HCH concentrations (dry weight basis) ranged from 2.2 to 20.2 ng/g (mean 7.7 ng/g) in surface sediments and from 26.6 to 972.7 ng/g (mean 187.0 ng/g) in settling particles, respectively. A clear seasonal variation in HCH sedimentation and HCH concentrations in sediments was observed. The maximal HCH deposition occurred following a spring phytoplankton bloom. The average flux of HCHs to sediment was approximately 21-fold higher in April to mid-June as compared to late June to October. This was attributed to the high vertical fluxes at the end of the spring phytoplankton bloom. The maximum values of HCH concentrations in sediments were observed in mid-June to late July. Concentrations of HCHs in sediments from the eutrophic lake were well-correlated with organic carbon contents in sediments. The annual sediment trap flux of HCHs in the eutrophic lake, which was estimated using data obtained in the eutrophic lake, was 117 μ g/m² yr, about 72% of which was attributed to the sedimentation corresponding to spring bloom phytoplankton deposition in late May to mid-June. The high sediment trap flux of HCHs in the eutrophic lake was related to serious local contamination.     

Measuring Ammonia Concentrations and Emissions from Agricultural Land and Liquid Surfaces: A Review

Abstract

Aerial ammonia concentrations (C _g) are measured using acid scrubbers, filter packs, denuders, or optical methods. Using C _g and wind speed or airflow rate, ammonia emission rate or flux can be directly estimated using enclosures or micrometeorological methods. Using nitrogen (N) recovery is not recommended, mainly because the different gaseous N components cannot be separated. Although low cost and replicable, chambers modify environmental conditions and are suitable only for comparing treatments. Wind tunnels do not modify environmental conditions as much as chambers, but they may not be appropriate for determining ammonia fluxes; however, they can be used to compare emissions and test models. Larger wind tunnels that also simulate natural wind profiles may be more useful for comparing treatments than micrometeorological methods because the latter require larger plots and are, thus, difficult to replicate. For determining absolute ammonia flux, the micrometeorological methods are the most suitable because they are nonintrusive. For use with micrometeorological methods, both the passive denuders and optical methods give comparable accuracies, although the latter give real-time C _g but at a higher cost. The passive denuder is wind weighted and also costs less than forced-air C _g measurement methods, but it requires calibration. When ammonia contamination during sample preparation and handling is a concern and separating the gas-phase ammonia and aerosol ammonium is not required, the scrubber is preferred over the passive denuder. The photothermal interferometer, because of its low detection limit and robustness, may hold potential for use in agriculture, but it requires evaluation. With its simpler theoretical basis and fewer restrictions, the integrated horizontal flux (IHF) method is preferable over other micrometeorological methods, particularly for lagoons, where berms and land-lagoon boundaries modify wind flow and flux gradients. With uniform wind flow, the ZINST method requiring measurement at one predetermined height may perform comparably to the IHF method but at a lower cost.     

Dry and wet deposition of water-insoluble dust and water-soluble chemical species during spring 2007 in Tsukuba,Japan

Dry and wet depositions were sampled daily in Tsukuba, Japan, in spring 2007. Temporal variations in the dry and wet deposition fluxes of dust and water-soluble chemical species were controlled largely by air mass origin, the water vapor mixing ratio, and Asian dust events. The contribution of local sources to dry deposition of dust was large when the wind speed was high. Dry deposition fluxes of water-soluble chemical species were larger in humid air masses than in dry air masses. Wet deposition fluxes of dust and water-soluble chemical species indicated that air masses that passed over dust source regions and industrial regions became mixed with the maritime air masses over the coastal site of the Asian continent and western part of the Japanese islands. The total deposition of dust was 4220 mg m^?2 month^?1, and that of water-soluble chemical species ranged from 10 to 636 mg m^?2 month^?1. Wet deposition fluxes of the total deposition flux of dust accounted for 72% and those of water-soluble chemical species was for 72–96%. In particular, the largest wet deposition occurred during a single Asian dust event on 3 April. This event accounted for 23% (950 mg m^?2 month^?1) of the monthly dust deposition flux and for 2–28% (0.43–51 mg m^?2 month^?1) of the monthly deposition flux of water-soluble chemical species. This result implies that the wet deposition flux associated with even one sporadic Asian dust event can have extensive impacts on both terrestrial and oceanic ecosystems in East Asia.     

A Federal Tax on Energy

Abstract

In this investigation, the collection efficiency of particulate emission control devices (PECDs), particulate matter (PM) emissions, and PM size distribution were determined experimentally at the inlet and outlet of PECDs at five coal-fired power plants. Different boilers, coals, and PECDs are used in these power plants. Measurement in situ was performed by an electrical low-pressure impactor with a sampling system, which consisted of an isokinetic sampler probe, precut cyclone, and two-stage dilution system with a sample line to the instruments. The size distribution was measured over a range from 0.03 to 10 µm. Before and after all of the PECDs, the particle number size distributions display a bimodal distribution. The PM_2.5 fraction emitted to atmosphere includes a significant amount of the mass from the coarse particle mode. The controlled and uncontrolled emission factors of total PM, inhalable PM (PM₁₀), and fine PM P(M_2.5) were obtained. Electrostatic precipitator (ESP) and baghouse total collection efficiencies are 96.38–99.89% and 99.94%, respectively. The minimum collection efficiency of the ESP and the baghouse both appear in the particle size range of 0.1–1 µm. In this size range, ESP and baghouse collection efficiencies are 85.79–98.6% and 99.54%. Real-time measurement shows that the mass and number concentration of PM₁₀ will be greatly affected by the operating conditions of the PECDs. The number of emitted particles increases with increasing boiler load level because of higher combustion temperature. During test run periods, the data reproducibility is satisfactory.     

Remote sampling of a CO2 point source in an urban setting

High frequency CO₂ and wind speed measurements were used to examine the urban baseline eddy covariance CO₂ flux and analyse the CO₂ rich plume from a local power station. A reliable relationship between high frequency CO₂ maxima and the rate of CO₂ emission at the power station was established. This relationship was shown to be highly dependant on wind speed. The ensemble mean plume was found to be Gaussian in horizontal profile with a width dependant on wind speed. The relationship between peak CO₂ mixing ratio and averaging time was shown to be a simple power law with a time exponent of approximately 0.5. The large, short pulses in CO₂ mixing ratio in the power plant plume were found to have an approximately Lorentzian shape. These pulses generated negative vertical eddy flux measurements so data from the plume sector were necessarily excluded from the flux baseline results. The plume-excluded flux had a similar magnitude and variability to those reported in other urban CO₂ flux studies despite this site not being ideal due to the proximity of roughness elements to the measurement point.     

Simulation of the evolution of particle size distributions containing coarse particulate in the atmospheric surface layer with a simple convection-diffusion-sedimentation model

The Fugitive Dust Model (FDM) and Industrial Source Complex (ISC), widely used coarse particulate dispersion models, have been shown inaccurate due to the neglect of vertical variations in atmospheric wind speed and turbulent diffusivity (Vesovic et al., 2001), omission of the gravitational advection velocity, and an underestimation of the ground deposition velocity (Kim and Larson, 2001). A simple, transient two-dimensional convection-diffusion-sedimentation model is proposed to simulate the evolution in particle size distribution of an aerosol ‘puff’ containing coarse particulate in the atmospheric surface layer. Monin-Okhubov similarity theory, accompanied by empirical observations made by Businger et al. (1971), is adopted to characterize the surface layer wind speed and turbulent diffusivity profiles over a wide range of atmospheric conditions. A first order analysis of the crossing trajectories effect suggests simulation data presented here are not significantly affected by particle inertia. The model is validated against Suffield experimental data in which coarse particulate deposition was measured out to a distance of 800 m from the source (Walker, 1965). Good agreement is found for the decay in ground deposits with distance from the source for stable atmospheres. Deposition data was also simulated for unstable atmospheric stratification and the current model was determined to modestly underestimate the peak concentration with increasing accuracy further downwind of the release. The current model's effective deposition velocity was compared to that suggested by Kim et al. (2000) and shows improvement with respect to FDM. Lastly, the model was used to simulate the dispersion of nine lognormal aerosol puffs in the lowest 50 m of the atmospheric surface layer for four classes of atmospheric stability. The simulated mass median aerodynamic diameters (MMAD) at multiple downwind sampling locations were calculated and plotted with distance from the source. The first 50 m from the source was found to have a substantial impact on the evolution of MMAD for stable atmospheric conditions. Away from the source, it was observed that particle size distributions were truncated by removal of all particles larger than about 60 μm. A particle Peclet number was also defined to quantify the relative importance of turbulent dispersion and sedimentation on particle motion in the vertical direction.     

Study on dissolved organic carbon in precipitation in Northern China

Dissolved organic carbon (DOC) was measured in 483 precipitation samples collected at 10 sites in Northern China from December 2007 to November 2008. The annual volume-weighted mean (VWM) concentrations and wet deposition fluxes of DOC for 10 sites ranged from 2.4 to 3.9 mg C/L and 1.4 to 2.7 g C m^?2 yr^?1, respectively. The proportion of DOC to total organic carbon (TOC) was 79% on average, suggesting that a significant fraction of TOC was present as insoluble particulate organic carbon. Due to intensive domestic coal use for house heating and smaller dilution of scavenged organic carbon, higher VWM concentrations of DOC were observed during winter and spring than during summer and autumn. When precipitation events were classified via air mass back-trajectories, the mixed trajectories from SE and NW always corresponded to significantly higher DOC than those from SE or NW alone, coinciding with the centre of a low pressure system moved eastward and the wind direction changed from southeast to northwest. The results also showed that each site had a similar seasonal variation for DOC wet deposition flux. The largest flux occurred during the rainy season, and the lowest flux appeared during winter months. The product of the TC/DOC ratio and the DOC flux yielded an average TC wet deposition flux of 3.2 g C m^?2 yr^?1 in Northern China, accounting for 8.6% and 22% of the carbon sink magnitude (37 g C m^?2 yr^?1) in terrestrial ecosystems and anthropogenic carbon emissions (14 g C m^?2 yr^?1), respectively. This indicates that atmospheric wet deposition of TC is a significant carbon flux that cannot be neglected in regional models of the carbon cycle, and should be considered along with dry deposition in the removal mechanism for carbon from regional atmosphere.     

Sedimentation and seasonal variation of hexachlorocyclohexanes in sediments in a eutrophic lake, China

Hexachlorocyclohexane (HCH) concentrations in sediments and sediment trap fluxes of particulate organic carbon and HCHs were measured bi-weekly from March 31 to October 18, 2006 in an urban eutrophic lake in Tianjin, China, in order to investigate sedimentation and seasonal variation of HCHs in sediments. HCH concentrations (dry weight basis) ranged from 2.2 to 20.2 ng/g (mean 7.7 ng/g) in surface sediments and from 26.6 to 972.7 ng/g (mean 187.0 ng/g) in settling particles, respectively. A clear seasonal variation in HCH sedimentation and HCH concentrations in sediments was observed. The maximal HCH deposition occurred following a spring phytoplankton bloom. The average flux of HCHs to sediment was approximately 21-fold higher in April to mid-June as compared to late June to October. This was attributed to the high vertical fluxes at the end of the spring phytoplankton bloom. The maximum values of HCH concentrations in sediments were observed in mid-June to late July. Concentrations of HCHs in sediments from the eutrophic lake were well-correlated with organic carbon contents in sediments. The annual sediment trap flux of HCHs in the eutrophic lake, which was estimated using data obtained in the eutrophic lake, was 117 microg/m2 yr, about 72% of which was attributed to the sedimentation corresponding to spring bloom phytoplankton deposition in late May to mid-June. The high sediment trap flux of HCHs in the eutrophic lake was related to serious local contamination.     

Dry deposition of particles to wave surfaces: II. Wind tunnel experiments

Wind tunnel measurements of particle dry deposition to wavy and flat surfaces were made to estimate the enhancement of deposition rates due to waves on water surfaces. Measurements were made of 4.0 and 6.7 μm uranine particles at wind speeds of 5 and 10 m s⁻¹ to sinusoidal waves with height to length ratios 2a/λ=0.1 and 0.03 and to flat surfaces. Results showed that deposition was greatest to the upslope portion of the wave, accounting for 40–45% of the total mass, followed by the trough (30%), downslope (15%), and crest (10–15%). These results generally agreed within experimental variability with modeling predictions (Zufall et al., 1999). Deposition was enhanced at the upslope due to the effects of particle interception and impaction on the wave. Total deposition to the wave surfaces was greater than deposition to the flat surface for a large majority of the cases. The average increase in deposition to both wave surfaces for both particle sizes and wind speeds over deposition to the flat surface was 80%.     

Spray atomization and deposition patterns of one newtonian and two pseudoplastic formulations after aerial application over a mature conifer forest in Newfoundland

Abstract

Spray atomization and deposition patterns of three formulations were investigated in five aerial spray trials in Newfoundland, to understand the inter‐relationships between physical properties, drop size spectra and recovery of the spray volume at ground level. Diflubenzuron (DFB) was sprayed at 30 g active ingredient in 2.0 L/ha. Futura XLV (Fu‐XLV) and Thuricide® 48LV (Thu‐48LV), spray formulations of Bacillus thuringiensis (B.t.), were both applied undiluted at 30 BIU/ha, but in volume rates of 2.1 L/ha and 2.36 L/ha respectively. Each of the three formulations was applied over a 15 ha plot using a Piper Pawnee aircraft fitted with six Micronair® AU5000 atomizers. Spray drops were sampled with Kromekote® cards and deposits were collected on glass plates. Physical properties measured were: viscosity at variable shear rates, volatility and surface tension. The viscosities increased progressively from low (for DFB), moderate (for Thu‐48LV) to high (for Fu‐XLV) values, showing a gradual increase in pseudoplastic behaviour of the three formulations. The volatility data indicated an inverse relationship to the viscosities, but the surface tensions were similar for all the formulations.

The highly pseudoplastic Fu‐XLV atomized into the least wide drop size spectrum. The Newtonian formulation of DFB, on the other hand, atomized into the widest drop spectrum; and the moderately pseudoplastic Thu‐48LV, into an intermediate drop spectrum. Thus viscosity and volatility were more important factors in liquid atomization and drop deposition, than surface tension. Among the three meteorological factors measured, relative humidity appeared more important in drop deposition than did wind speed and temperature, within the range measured.     

Factors contributing to seasonal variations in wet deposition fluxes of trace elements at sites along Japan Sea coast

In this study, we measured the wet deposition fluxes of ten trace elements (As, Cd, Cr, Cu, Mn, Ni, Pb, Sb, V and Zn) from December 2002 to March 2006 at three sites along the Japan Sea coast, which have been strongly affected by the long-range transport of air pollutants from the Asian continent. Also, factors, contributing to their seasonal variations were investigated. At the northern and central sites, the monthly wet deposition fluxes of all or most trace elements greatly increased during the cold season (typically, November–April), along with their monthly average (volume-weighted) concentrations in the precipitation. The cold/warm season ratios for the average concentrations of trace elements in precipitation were within the range of 2.7–5.1 at the northern site and 1.8–5.9 at the central site, which were similar to the average scavenging ratios (= concentration in precipitation/concentration in air) at each site. However, there were small differences (0.47–1.2 at the northern site and 0.73–1.7 at the central site) in the ratios of average concentrations in air between the two seasons. These suggest that the increase in the wet deposition fluxes of trace elements during the cold season is due to increases in their scavenging ratios. On the other hand, the result for the southern site was different from those at the other sites. The number of days when the daily maximum wind speed exceeded 10 m s^?1 at the meteorological observatories near the study sites increased markedly during the cold season at the northern and central sites, showing that strong winds usually blow during the cold season at those sites, but not at the southern site. Higher wind speed transports larger amounts of constituents into the cloud system, which can result in their increased concentrations in precipitation. Thus, high scavenging ratios of trace elements during the cold season may be caused by the increase in their amounts of discharge into the cloud system owing to high wind speed, suggesting that wind speed is an important factor in the seasonal variations in the wet deposition fluxes.     

Development and Evaluation of the PRIME Plume Rise and Building Downwash Model

ABSTRACT

A new Gaussian dispersion model, the Plume Rise Model Enhancements (PRIME), has been developed for plume rise and building downwash. PRIME considers the position of the stack relative to the building, streamline deflection near the building, and vertical wind speed shear and velocity deficit effects on plume rise. Within the wake created by a sharp-edged, rectangular building, PRIME explicitly calculates fields of turbulence intensity, wind speed, and streamline slope, which gradually decay to ambient values downwind of the building. The plume trajectory within these modified fields is estimated using a numerical plume rise model. A probability density function and an eddy diffusivity scheme are used for dispersion in the wake. A cavity module calculates the fraction of plume mass captured by and recirculated within the near wake. The captured plume is re-emitted to the far wake as a volume source and added to the uncaptured primary plume contribution to obtain the far wake concentrations.

The modeling procedures currently recommended by the U.S. Environmental Protection Agency (EPA), using SCREEN and the Industrial Source Complex model (ISC), do not include these features. PRIME also avoids the discontinuities resulting from the different downwash modules within the current models and the reported overpredictions during light-wind speed, stable conditions. PRIME is intended for use in regulatory models. It was evaluated using data from a power plant measurement program, a tracer field study for a combustion turbine, and several wind-tunnel studies. PRIME performed as well as or better than ISC/SCREEN for nearly all of the comparisons.     

Electrostatic Precipitation of Ultrafine Particles Enhanced by Simultaneous Diffusional Deposition on Wire Screens

Abstract

A laboratory-scale electrostatic precipitator has been designed and constructed in which the grounded collector plate has been substituted by a set of wire screens placed perpendicularly to the gas flow. Particles are deposited onto the screens by two mechanisms—electrostatic deposition and diffusional deposition—which act simultaneously. On the one hand, electrostatic deposition is effective for relatively large particles, but it is quite ineffective for the smallest ones because their charging probability in the corona field is too low. On the other hand, the diffusional collection efficiency of particles on fibers is high for small particles but low for the larger ones. Therefore, the simultaneous diffusional-electrostatic precipitation may become a useful technique for efficient filtration of particles below 0.1 μm. A preliminary experimental evaluation of this filtering device has shown that submicrometer particles with diameters down to a few nanometers can be collected with number efficiencies greater than 99%.     

An Evaluation of Flare Combustion Efficiency Using Open-Path Fourier Transform Infrared Technology

ABSTRACT

Open-path Fourier transform infrared (OP-FTIR) technology was used to evaluate the combustion efficiency of a flare for comparison to several combustion models. Most flares have been considered an effective method for destroying organic compounds and anything that burns. As the Btu content of the flare gas is reduced, the combustion efficiency may also be reduced. Recent studies have suggested that lower Btu flares may have efficiencies as low as 65%. In addition, models have been developed to predict the effect of wind speed and stack discharge velocity on the combustion efficiency. This study was conducted on a low-Btu flare gas that is primarily CO. While the models would predict efficiencies as low as 30%, the sampling using OP-FTIR showed most combustion efficiencies well above 90%. Three methods were used to track combustion efficiency: monitoring the ratio of CO to CO₂, monitoring the ratio of CO to tracer gas, and dispersion modeling. This study was complicated by the presence of two flare stacks, thus two tracer gases were used—SF₆ and CF₄. A method was developed for distinguishing between the two stacks and quantifying the efficiency in each stack.