Pesticide concentration variations correlated with well bore volume removal in shallow coastal plain ground water

Abstract

The effects of well bore volume removal (V_n) on the concentration of alachlor [2‐chloro‐N‐(2,6‐diethylphenyl)‐N‐(methoxy methyl) acetamide] and prometon (6‐methoxy‐N,N'‐bis(1‐methylethyl)‐1,3,5‐triazine‐2,4‐diamine] in ground water obtained from three monitoring wells installed in the Coastal Plain region of North Carolina was investigated. Seasonal effects were also investigated by conducting the exercise in February and May. In the majority of cases, the lowest pesticide concentrations occurred in the initial well bore volume (V₁ = stagnant water). Removal of additional well bore volumes (V₂ to V₁₀) from two of the wells resulted in pesticide concentrations that did not vary substantially. This indicates that a representative aquifer sample was obtainable, in most cases from these wells, after removal of the initial well bore volume. In contrast, a third well required the purging of two well bore volumes before a stable alachlor concentration was achieved. Seasonal effects of bore volume removal vs. pesticide concentrations for the three wells were not significant (P > 0.05). It was concluded that a protocol for improved accuracy in pesticide analyses of ground water can be obtained by establishing a pesticide concentration‐purging (well bore volume) relationship for each well.     

Runoff and leaching of atrazine and alachlor on a sandy soil as affected by application in sprinkler irrigation

Abstract

Rainfall simulation was used with small packed boxes of soil to compare runoff of herbicides applied by conventional spray and injection into sprinkler‐irrigation (chemigation), under severe rainfall conditions. It was hypothesized that the larger water volumes used in chemigation would leach some of the chemicals out of the soil surface rainfall interaction zone, and thus reduce the amounts of herbicides available for runoff. A 47‐mm rain falling in a 2‐hour event 24 hours after application of alachlor (2‐chloro‐N‐(2,6‐diethylphenyl)‐N‐(methoxymethyl)‐acetamide) and atrazine (6‐chloro‐N‐ethyl‐N‐(1‐methylethyl)‐1,3,5‐triazine‐2,4‐diamine) was simulated. The design of the boxes allowed a measurement of pesticide concentrations in splash water throughout the rainfall event. Initial atrazine concentrations exceeding its’ solubility were observed. When the herbicides were applied in 64000 L/ha of water (simulating chemigation in 6.4 mm irrigation water) to the surface of a Tifton loamy sand, subsequent herbicide losses in runoff water were decreased by 90% for atrazine and 91% for alachlor, as compared to losses from applications in typical carrier water volumes of 187 L/ha. However, this difference was not due to an herbicide leaching effect but to a 96% decrease in the amount of runoff from the chemigated plots. Only 0.3 mm of runoff occurred from the chemigated boxes while 7.4 mm runoff occurred from the conventionally‐treated boxes, even though antecedent moisture was higher in the former. Two possible explanations for this unexpected result are (a) increased aggregate stability in the more moist condition, leading to less surface sealing during subsequent rainfall, or (b) a hydrophobic effect in the drier boxes. In the majority of these pans herbicide loss was much less in runoff than in leachate water. Thus, in this soil, application of these herbicides by chemigation would decrease their potential for pollution only in situations where runoff is a greater potential threat than leaching.     

Enzyme-immunoassay techniques for the detection of atrazine in water samples: Evaluation of a commercial tube based assay

Environmental immunoassays can help lower the operating costs and improve the effectiveness of residue laboratories. The present study assesses the ability of a commercially available enzyme immunoassay (EIA) to detect triazine herbicides in water. The tube based EIA could detect atrazine in lake and river water with detection limits of 62 pg/mL and 180 pg/mL respectively. The assay's ability to quantify atrazine in a set of 124 water samples taken from many parts of Canada was compared with a reference method that used gas chromatographic separation combined with a nitrogen phosphorous detector (GC-NPD) (R=0.919). A 71 % reduction in analytical load was achieved at a threshold concentration of 1 ng/mL. There were 2.4 % false negative and 0.8 % false positive results associated with that load reduction. The variability of the assay control parameters was generally within two standard deviations of the mean response for 65 assays. The EIA for atrazine is recommended for use as a screening technique and as an inexpensive way to monitor triazine levels in waters that are known to be contaminated with those herbicides.     

Analysis of pesticide runoff from mid-Texas estuaries and risk assessment implications for marine phytoplankton

During 1993, estuarine surface water samples were collected from the mid-Texas coast (Corpus Christi to Port Lavaca, TX). Agricultural watershed areas as well as tidal creeks immediately downstream were chosen as sampling sites along with adjoining bay sampling stations. Collections were made throughout the growing season (February to October 1993) before and after periods of significant (> 1.25 cm) rainfall. All samples were initially screened for the presence of pesticides using enzyme-linked immunosorbent assay (ELISA) test kits (EnviroGard) for triazine herbicides and carbamate insecticides. All samples were extracted and then analyzed using gas chromatography (GC) for quantification of atrazine. Only samples testing positive for carbamate insecticides via ELISA were further extracted for GC analysis to quantify aldicarb and carbofuran. Additionally, laboratory toxicity tests using phytoplankton were examined from published, peer-reviewed literature and compared with the atrazine field levels found in Texas. Results of ELISA screening indicated the presence of triazine herbicides in nearly all samples (>93%). GC analysis further confirmed the presence of atrazine concentrations ranging from <0.01-62.5 microg/L. Screening tests also found detectable levels of carbamate insecticides (aldicarb and carbofuran) that were also confirmed and quantified by GC. Comparison of measured concentrations of atrazine compared with published toxicity tests results indicated that there was a potential environmental risk for marine/estuarine phytoplankton in surface waters of Texas estuaries, particularly when the chronic nature of atrazine exposure is considered.     

除草剂阿特拉津(Atrazine)的环境行为综述

阿特拉津（２－氯－４－乙胺基－６－异丙氨基－１，３，５，－三氮苯）是目前应用广泛的化学除草剂之一。在世界许多国家和地区的地表水和地下水中已检出了阿特拉津的残留物。阿特拉津对人类的威胁究竟有多大，已成为目前研究的热点。本文从阿特拉津的检测方法、动力学性质、生化性质及风险评估四个方面进行了综述，并提出了自己的观点。     

Herbicide movement and dissipation at four midwestern sites

Abstract

This study was conducted to evaluate atrazine (2‐chloro‐4‐ethylamino‐6‐isopropyl‐1, 3, 5‐triazine) and alachlor (2‐chIoro‐N‐(methoxymethyl)acetamide) dissipation and movement to shallow aquifers across the Northern Sand Plains region of the United States. Sites were located at Minnesota on a Zimmerman fine sand, North Dakota on Hecla sandy loam, South Dakota on a Brandt silty clay loam, and Wisconsin on a Sparta sand. Herbicide concentrations were determined in soil samples taken to 90 cm four times during the growing season and water samples taken from the top one m of aquifer at least once every three months. Herbicides were detected to a depth of 30 cm in Sparta sand and 90 cm in all other soils. Some aquifer samples from each site contained atrazine with the highest concentration in the aquifer beneath the Sparta sand (1.28 μg L^‐1). Alachlor was detected only once in the aquifer at the SD site. The time to 50% atrazine dissipation (DT₅₀) in the top 15 cm of soil averaged about 21 d in Sparta and Zimmerman sands and more than 45 d for Brandt and Hecla soils. Atrazine DT₅₀ was correlated positively with % clay and organic carbon (OC), and negatively with % fine sand. Alachlor DT₅₀ ranged from 12 to 32 d for Zimmerman and Brandt soils, respectively, and was correlated negatively with % clay and OC and positively with % sand.     

Fate of atrazine and chlorpyrifos during solid state fermentation—examination of processes

Abstract

Solid state fermentation (SSF) was investigated as a means to dispose of two commonly used pesticides, chlorpyrifos (O, O‐diethyl O‐(3,5,6‐trichloro‐2‐pyridyl) phosphorothioate) and atrazine (2‐chloro‐4‐ethylamino‐6‐isopropylamino‐1,3,5‐triazine). SSF experiments were carried out in bench‐scale bioreaetors (equipped with CO₂ and volatile organic traps) containing a mixture of lignocellulosic materials and a radiolabeled pesticide. Ethyl acetate‐extractable, alkali soluble, and alkali insoluble fractions were evaluated for radioactivity following a 60‐d incubation period at 40°C. The majority of the [2, 6‐pyridyl‐¹⁴C]chlorpyrifos was associated with the ethyl acetate extract (about 74%), 17% was trapped as organic volatiles by polyurethane foam traps and < 0.5% of the chlorpyrifos was mineralized to CO². Only small amounts of the radioactivity were associated with alkali soluble (0.0003%) and alkali insoluble (0.3%) fractions. In the [¹⁴C‐U‐ring] atrazine bioreactors, very little of the radioactivity volatilized (<0.5%) and less than 0.5% was mineralized to CO₂. Approximately 57% of the applied radioactivity was associated with the ethyl acetate extract while 9% and 24% of the radioactivity was associated with the alkali soluble (humic and fulvic acids) and alkali insoluble fractions, respectively. Possible reaction mechanisms by which covalent bonds could be formed between atrazine (or metabolites) and humic substances were investigated. The issue of bound atrazine residue (alkali soluble fraction) was at least partially resolved. Oxidative coupling experiments revealed that formation of covalent bond linkages between amino substituent groups of atrazine residue and humic substances is highly unlikely.     

Metolachlor persistence in laboratory and field soils under Indian tropical conditions

Abstract

Metolachlor [2‐chloro‐N‐(2‐methoxy‐1‐methylethyl)‐2'‐ethyl‐6'‐methyl acetanilide] dissipation under both field and laboratory conditions were studied during summer season in an Indian soil. Metolachlor was found to have moderate persistence with a half‐life of 27 days in field. The herbicide got leached down to 15–30 cm soil layer and residues were found up to harvest day of the sunflower crop in both 0–15 cm and 15–30 cm soil layers. Metolachlor was found to be more persistent in laboratory studies conducted for 190 days. The rate of degradation was faster in soil under flooded partial anaerobic conditions as compared to aerobic soil with a half‐life of 44.3 days. In aerobic soil, metolachlor was very stable with only 49% dissipation in 130 days. Residues remained in both the soils up to the end of the experimental period of 190 days.     

Behavior of atrazine in soils of tropical zone

Abstract

Movement and degradation of ¹⁴C‐atrazine (2‐chloro 4‐(ethylamino)‐6‐(isopropylamino)‐s‐triazine, was studied in undisturbed soil columns (0.50m length × 0.10m diameter) of Gley Humic and Deep Red Latosol from a maize crop region of Sao Paulo state, Brazil. Atrazine residues were largely confined to the 0–20cm layers over a 12 month period Atrazine degraded to the dealkylated metabolites deisopropylatrazine and deethylatrazine, but the major metabolite was hydroxyatrazine, mainly in the Gley Humic soil. Activity detected in the leachate was equivalent to an atrazine concentration of 0.08 to 0.11μg/1.

The persistence of ¹⁴C‐atrazine in a maize‐bean crop rotation was evaluated in lysimeters, using Gley Humic and Deep Red Latosol soils. Uptake of the radiocarbon by maize plants after 14‐days growth was equivalent to a herbicide concentration of 3.9μg/g fresh tissue and was similar in both soils. High atrazine degradation to hydroxyatrazine was detected by tic of maize extracts. After maize harvest, when beans were sown the Gley Humic soil contained an atrazine concentration of 0.29 μg/g soil and the Deep Red Latosol, 0.13 μg/g soil in the 0–30 cm layer. Activity detected in bean plants corresponded to a herbicide concentration of 0.26 (Gley Humic soil) and 0.32μg/g fresh tissue (Deep Red Latossol) after 14 days growth and 0.43 (Gley Humic soil) and 0.50 μg/g fresh tissue (Deep Red Latossol) after 97 days growth. Traces of activity equivalent to 0.06 and 0.02μg/g fresh tissue were detected in bean seeds at harvest. Non‐extractable (bound) residues in the soils at 235 days accounted for 66.6 to 75% (Gley Humic soil and Deep Red Latossol) of the total residual activity.     

Atrazine degradation in a containerized rhizosphere system

Abstract

The effect of atrazine (2‐chloro‐4‐ethylamino‐6‐isopropylamino‐s‐triazine) on rhizosphere microorganisms and its fate in a containerized rhizosphere system was studied. The rhizosphere system consisted of corn grown in pot containing a defined potting mix of sand and bark with atrazine. Sterilized potting mix and a container without plants served as controls. Atrazine was extracted and analyzed via HPLC. Fluorescent pseudomonad populations increased 100‐fold in the rhizposphere during a 60‐day incubation period as compared to the nonvegetated control. Atrazine degradation was higher in the rhizosphere system (half‐life of 7 days) compared to the nonvegetated control (half‐life of greater than 45 days). The major degradation product detected in the rhizosphere system was deisopropylatrazine; other products detected included deethylatrazine, deethylhydroxyatrazine, deisopropylatrazine and hydroxyatrazine. Hydroxyatrazine was detected in the nonvegetated and sterile controls. The containerized rhizosphere system provides an experimental system to study the fate of pesticidal chemicals as well as the effects on microbial populations.     

Books available

Abstract

The leaching behaviour of the herbicide acetochlor [2‐chloro‐N‐(2‐ethyl‐6‐methylphenyl)‐N‐(ethoxymethyl)acetamide] was determined as compared with two congener compounds, alachlor [2‐chloro‐N‐(2,6‐diethylphenyl)‐N‐(methoxymethyl)acetamide] and metolachlor [2‐chloro‐N‐(2‐ethyl‐6‐methylphenyl)‐N‐(2‐methoxy‐l‐methylethyl)acetamide]. The leaching profiles of the herbicides in columns with different types of soil and their capacity factors in reverse phase HPLC were compared. An approach for preliminary characteristic of the potential for water pollution of acetochlor is presented. The herbicide is classified as a leacher in soil and its potential for contamination of ground water is comparable with those of alachlor and metolachlor.     

Interactions of sodium azide with triazine herbicides: effect on sorption to soils

Sodium azide (NaN(3)) is one of the biocides commonly used to inhibit microbial growth during sorption experiments. However, a few reports have suggested that NaN(3) can react with the analyte of interest. In this study, the interactions of NaN(3) with triazine herbicides were investigated and the effect of atrazine transformation on its sorption to soil was evaluated. The concentration of atrazine in the presence of NaN(3) decreased significantly over period of time. After 14 days, only 38% of the initial atrazine concentration (10 mg l(-1)) was detected in a solution containing 1,000 mg l(-1) NaN(3) at pH 5.5. The magnitude and the rate of atrazine transformation increased with increase in NaN(3) load and with decrease in pH. In contrast to atrazine behavior, the concentrations of prometon and ametryn did not change during the experiment. GC/MS analysis indicated that the chlorine atom of atrazine is replaced by the azide group yielding 2-azido-4-(ethylamino)-6-(isopropylamino)-s-triazine. Atrazine transformation by NaN(3) significantly affected sorption of herbicide to soil. The presence of NaN(3) affects indirectly the sorption of atrazine due to competitive effect of its derivative. Our results demonstrated that the application of NaN(3) as a biocide in sorption-desorption experiments must be carefully evaluated. This issue is vital for sorption experiments conducted over long periods of time or/and with concentration of NaN(3) higher than 100 mg l(-1).     

Atrazine removal by ozonation processes in surface waters

Abstract

Atrazine (6‐chloro‐N‐ethyl‐N'‐isopropyl‐1,3,5‐triazinedyl‐2,4‐diamine) was treated with ozone alone and in combination with hydrogen peroxide or UV radiation in three surface waters. Experiments were carried out in two bubble reactors operated continously. Variables investigated were the ozone partial pressure, temperature, pH, mass flow ratio of oxidants fed: hydrogen peroxide and ozone and the type of oxidation including UV radiation alone. Residence time for the aqueous phase was kept at 10 min. Concentrations of some intermediates, including deethylatrazine, deisopropylatrazine and deethyldeisopropylatrazine, were also followed. The nature of water, specifically the alkalinity and pH were found to be important variables that affected atrazine (ATZ) removal. Surface waters with low alkalinity and high pH allowed the highest removal of ATZ to be reached. There was an optimum hydrogen peroxide to ozone mass flow ratio that resulted in the highest ATZ removal in each surface water treated. This optimum was above the theoretical stoichiometry of the process. Therefore, to reach the maximum removal of ATZ in a O₃/H₂O₂ process, more hydrogen peroxide was needed in the surface waters treated than in ultrapure water under similar experimental conditions. In some cases, UV radiation alone resulted in the removal of ATZ higher than ozonation alone. This was likely due to the alkalinity of the surface water. Ozonation and UV radiation processes yield different amounts of hydrogen peroxide. Combined ozonations (O₃/H₂O₂ and O₃/UV) lead to ATZ removals higher than single ozonation or UV radiation but the formation of intermediates was higher.     

Phytotoxicity of atrazine and alachlor in soil amended with sludge,manure and activated carbon

Abstract

Greenhouse studies were conducted to determine the influence of waste‐activated carbon (WAC), digested municipal sewage sludge (DMS), and animal manure on herbicidal activity of atrazine [2‐chloro‐4‐(ethylamino)‐6‐(isopropylamino)‐s‐trazine] and alachlor [2‐chloro‐2’,6'‐diethyl‐N‐(methoxymethyl)acetanilide] in a Plainfield sandy soil. Amendments generally reduced bioactivity against oat (Avena sativa L.) and Japanese millet (E. crus‐galli frumentacea). The extent to which herbicide phytotoxicity was inhibited depended upon the application rate and the kind of soil amendment. WAC, applied at the loading rate of 2.1 mt C/ha, showed a significant inhibitory effect on both herbicides. In DMS‐ and manure‐amended soil, the reduction of atrazine activity was not significant at the rate of 8.4 mt C/ha, but reduction of alachlor activity was significant at the rate of 4.2 mt C/ha. Despite inhibition of herbicidal activity, the ED₅₀ of atrazine and alachlor was below 2 ppm in most of the amendment treatments. Before adopting carbon‐rich waste amendments as management practices for controlling pesticide leaching in coarse‐textured soils, further studies are needed to characterize how alterations in sorption, leaching and degradation may affect herbicidal activity.     

Determination of atrazine in rainfall and surface water by enzyme immunoassay

Rainwater and surface water from four sites in Germany (Bavaria and Lower Saxony) were analyzed for atrazine by enzyme immunoassay from June 1990 until October 1992. The limit of quantification of the immunoassay was 0.02 μg/L with a middle of the test at 0.2 μg/L. About 60 % of the samples contained measurable amounts of atrazine. Seasonal trends were observed, with the highest concentration in the summer months of up to 4 μg/L for rainwater and up to 15 μg/L for surface waters. The highest concentrations were found in agricultural areas, while in the investigated national parks up to 0.56 μg/L could be detected in rain water. This points to long-range atmospheric transport from agricultural areas to pristine national parks. Samples from forest stands usually showed higher atrazine concentrations than samples from open fields. Deposition rates of 10 – 50 μg/m² · yr were observed in the national parks and 10–180 μg/m² · yr at the agricultural sites. Comparison of results obtained by enzyme immunoassay and GC/MS showed a good correlation of r = 0.95.     

Gas chromatography/mass spectrometry applied for the analysis of triazine herbicides in environmental waters

The excess use of triazine herbicides in agriculture causes severe contamination to the environment especially for ground water. Gas chromatography coupled with mass spectrometry (GC/MS) was used to analyze simazine, atrazine (ATR), cyanazine, as well as the degradation products of ATR such as deethylatrazine and deisopropylatrazine in environmental water samples. These compounds were baseline separated by the established GC method. The water samples were pre-concentrated by solid-phase-extraction (SPE) and analyzed by ion trap MS at sub- to low-ppt levels. Recovery of ATR by the SPE pre-concentration using a C18 cartridge was determined as 90.5 +/- 3.5%. Detection limit of the method using selected ion monitoring technique for ATR was 1.7 ppt when one liter water was analyzed. The relative analytical error for ATR fortified water samples at 200 ppt was -12.5% (n=12) with triple analysis and the relative standard deviation was 3.2%. Trace levels of ATR at 3.9 and 9.7 ppt were determined in water samples collected from a reservoir and a river in Hong Kong.     

Appendix

Abstract

An atrazine‐degrading bacterial isolate (M91–3) was able to utilize simazine and cyanazine as N sources for glucose‐dependent growth. The degradation of these three 5‐triazine herbicides was also investigated in binary and ternary mixtures. The organism used atrazine and simazine indiscriminately, whereas cyanazine degradation was slow and delayed until the depletion of the two other herbicides. There was no apparent effect of other commonly used herbicides on the rate of atrazine degradation by M91–3.     

Effects of planting system design on the toxicological sensitivity of Myriophyllum spicatum and Elodea canadensis to atrazine

The triazine herbicide atrazine (2-chloro-4-ethylamino-6-isopropylamino-s-trazine) was selected as a chemical stressor in an investigation of how toxicological responses of individually grown macrophytes reflect those of plants grown in more natural model populations and two-species communities. Phytotoxicity of the compound to Myriophyllumspicatum L. and Elodeacanadensis Michx. was assessed under semi-natural field conditions using 12000l outdoor microcosms. Exposure concentrations of 25, 50, 100, 250mugl(-1) plus controls (n=3) were evaluated, selected to fall within a range of concentrations known to produce a toxic response in the tested macrophytes, and effective concentrations required to cause a decrease in biomass endpoints by 10%, 25%, and 50% were estimated. The sensitivities of aquatic plants to atrazine did not differ substantially between planting systems, and few interactions between the effects of the planting method and atrazine effects on macrophyte biomass were detected using a two-way ANOVA. A lack of significant differences in biomass and relative growth rate measures between plants grown under the various test systems also indicated that interactions between and among species did not influence growth of plants in the model population and communities. Under these test conditions, the use of the "cone-tainer" method provided estimates of toxicity consistent with those from plants grown in assemblages, and potential interactions between plants were not found to modify the response of macrophytes to atrazine.     

Monitoring of Triazine and Phenylurea Herbicides in the Surface Waters of Greece

A large-scale study was implemented to monitor triazine and phenylurea herbicides in the main surface water bodies of continental Greece from October 1998 to September 1999. Samples from 10 rivers and 7 lakes were analyzed for the presence of five triazine (atrazine, cyanazine, prometryne, simazine, terbuthylazine) and five phenylurea (chlorotoluron, diuron, linuron, metobromuron, monolinuron) herbicides. The samples were extracted with C18 cartridges and analyzed by high-performance liquid chromatography–diode array detection (HPLC-DAD). The most frequently detected herbicides were atrazine, followed by prometryne, cyanazine, and simazine. The concentrations of the compounds were generally low (< 0.78 μ g/L) and are not considered harmful for the freshwater ecosystem. Most of the positive samples were taken from the water bodies of northern Greece where agricultural activity is more intense.     

Monitoring of triazine and phenylurea herbicides in the surface waters of Greece

A large-scale study was implemented to monitor triazine and phenylurea herbicides in the main surface water bodies of continental Greece from October 1998 to September 1999. Samples from 10 rivers and 7 lakes were analyzed for the presence of five triazine (atrazine, cyanazine, prometryne, simazine, terbuthylazine) and five phenylurea (chlorotoluron, diuron, linuron, metobromuron, monolinuron) herbicides. The samples were extracted with C18 cartridges and analyzed by high-performance liquid chromatography-diode array detection (HPLC-DAD). The most frequently detected herbicides were atrazine, followed by prometryne, cyanazine, and simazine. The concentrations of the compounds were generally low (< 0.78 micro g/L) and are not considered harmful for the freshwater ecosystem. Most of the positive samples were taken from the water bodies of northern Greece where agricultural activity is more intense.