废杂铜回收利用工艺技术现状及展望

随着社会经济的发展,铜生产和消费的矛盾日益突出。废杂铜作为一种再生资源,其回收利用不仅能够缓解我国铜矿资源缺乏的现状,而且也符合国家当前节能减排和环保的要求。概述了废杂铜的回收分类和生产工艺技术现状,并对今后的发展趋势进行了展望。     

Leaching behaviour of different scrap materials at recovery and recycling companies: Full-, pilot- and lab-scale investigation

Scrap material recovery and recycling companies are confronted with waste water that has a highly fluctuating flow rate and composition. Common pollutants, such as COD, nutrients and suspended solids, potentially toxic metals, polyaromatic hydrocarbons and poly chlorinated biphenyls can exceed the discharge limits. An analysis of the leaching behaviour of different scrap materials and scrap yard sweepings was performed at full-scale, pilot-scale and lab-scale in order to find possible preventive solutions for this waste water problem. The results of these leaching tests (with concentrations that frequently exceeded the Flemish discharge limits) showed the importance of regular sweeping campaigns at the company, leak proof or covered storage of specific scrap materials and oil/water separation on particular leachates. The particulate versus dissolved fraction was also studied for the pollutants. For example, up to 98% of the polyaromatic hydrocarbons, poly chlorinated biphenyls and some metals were in the particulate form. This confirms the (potential) applicability of sedimentation and filtration techniques for the treatment of the majority of the leachates, and as such the rainwater run-off as a whole.     

Management of MSW in Spain and recovery of packaging steel scrap

Packaging steel is more advantageously recovered and recycled than other packaging material due to its magnetic properties. The steel used for packaging is of high quality, and post-consumer waste therefore produces high-grade ferrous scrap. Recycling is thus an important issue for reducing raw material consumption, including iron ore, coal and energy. Household refuse management consists of collection/disposal, transport, and processing and treatment - incineration and composting being the most widely used methods in Spain. Total Spanish MSW production exceeds 21 million tons per year, of which 28.1% and 6.2% are treated in compost and incineration plants, respectively. This paper presents a comprehensive study of incineration and compost plants in Spain, including a review of the different processes and technologies employed and the characteristics and quality of the recovered ferrous scrap. Of the total amount of packaging steel scrap recovered from MSW, 38% comes from compost plants and 14% from incineration plants. Ferrous scrap from incineration plants presents a high degree of chemical alteration as a consequence of the thermal process to which the MSW is subjected, particularly the conditions in which the slag is cooled, and accordingly its quality diminishes. Fragmentation and magnetic separation processes produce an enhancement of the scrap quality. Ferrous scrap from compost plants has a high tin content, which negatively affects its recycling. Cleaning and detinning processes are required prior to recycling.     

Energy implications of the thermal recovery of biodegradable municipal waste materials in the United Kingdom

Waste management policies and legislation in many developed countries call for a reduction in the quantity of biodegradable waste landfilled. Anaerobic digestion, combustion and gasification are options for managing biodegradable waste while generating renewable energy. However, very little research has been carried to establish the overall energy balance of the collection, preparation and energy recovery processes for different types of wastes. Without this information, it is impossible to determine the optimum method for managing a particular waste to recover renewable energy. In this study, energy balances were carried out for the thermal processing of food waste, garden waste, wood, waste paper and the non-recyclable fraction of municipal waste. For all of these wastes, combustion in dedicated facilities or incineration with the municipal waste stream was the most energy-advantageous option. However, we identified a lack of reliable information on the energy consumed in collecting individual wastes and preparing the wastes for thermal processing. There was also little reliable information on the performance and efficiency of anaerobic digestion and gasification facilities for waste.     

我国废钢铁市场的发展前景及废钢电子交易推荐标准

随着我国钢铁工业高速发展和国家对节能减排的高度重视,废钢铁资源的应用倍受业内关注。对我国废钢供需市场的规模、现状及发展前景进行分析和预测,并对我国废钢电子交易推荐标准进行详细介绍,指出作为大宗商品交易发展方向的电子交易模式,是我国废钢贸易的发展趋势,有利于废钢市场有序健康发展。     

废钢产业转型升级与废钢行业预测

随着我国经济社会的快速发展及城镇化水平的提高,作为基础材料的钢铁工业也随之快速发展。介绍了处于废钢产业前端的废钢采集供应、废钢铁应用企业、废钢加工设备制造业等由于钢铁工业的发展而加快转型升级,并对2011年废钢行情的总体趋势进行判断。     

Investigation of hydrocyclones for the separation of shredded fridge plastics

The recycling of fridges produces a mixed plastic product of limited value. In order to maximise its value, the separation of the individual polymers that include high impact polystyrene (HIPS), acrylonitrile butadiene styrene (ABS), polyvinyl chloride (PVC) and polyethylene (PE) must take place. The effectiveness of a hydrocyclone system for the separation of these plastics, using both water and calcium chloride solutions, has been investigated. In addition a qualitative procedure for the determination of the HIPS content of a mixed ABS/HIPS product, by selective dissolution in R-limonene, has been developed. It was found that the effective density of separation depended on the particle size and aspect ratio. As the particle size and aspect ratio decreased, the separation became more efficient and the offset between separation density and hydrocyclone medium density decreased. This suggests that, for efficient density separation, closely sized, fine plastic fractions are required. Using these criteria, it was found that the removal of high density plastic such as PVC was readily achieved using a hydrocyclone. A partial separation of HIPS from ABS was found to be possible, taking advantage of a small density difference, using a hydrocyclone medium density of 1035kgm(-3).     

Foamed lightweight materials made from mixed scrap metal waste powder and sewage sludge ash.

The porous properties and pozzolanic effects of sewage sludge ash (SSA) make it possible to produce lightweight materials. This study explored the effects of different metallic foaming agents, made from waste aluminium products, on the foaming behaviours and engineering characteristics, as well as the microstructure of sewage sludge ash foamed lightweight materials. The results indicated that aluminium powder and mixed scrap metal waste powder possessed similar chemical compositions. After proper pre-treatment, waste aluminium products proved to be ideal substitutes for metallic foaming agents. Increasing the amount of mixed scrap metal waste by 10-15% compared with aluminium powder would produce a similar foaming ratio and compressive strength. The reaction of the metallic foaming agents mainly produced pores larger than 10 microm, different from the hydration reaction of cement that produced pores smaller than 1 microm mostly. To meet the requirements of the lightweight materials characteristics and the compressive strength, the amount of SSA could be up to 60-80% of the total solids. An adequate amount of aluminium powder is 0.5-0.9% of the total solids. Increasing the fineness of the mixed scrap metal waste powder could effectively reduce the amount required and improve the foaming ratio.     

进口含锌物料的表征和鉴别

采用X射线荧光光谱(XRF)、X射线衍射光谱(XRD)等分析手段,对4种进口疑似固体废物的含锌物料进行了表征。通过分析含锌物料的主要元素组成、物相组成和常规理化特征,结合外观特征,与含锌矿物、含锌产品及相关文献资料等进行比对,推导出含锌物料的产生来源。然后,参照我国《进口废物管理目录》得出鉴别结论。结果表明:4种含锌物料分别为锌矿、湿法冶炼锌浸出渣、热镀锌灰和固定CO2产物;后3种属于我国目前禁止进口的固体废物。     

Suitability of shredded tires for use in landfill leachate collection systems

The suitability of shredded tires or "tire chips" for use in the leachate collection drainage layer of a municipal solid waste landfill was investigated in terms of the: (1) compressibility of the tire chips and resulting changes in hydraulic conductivity under varying applied loads, and (2) effect of leachate pH on the shredded tries compressibility and hydraulic conductivity behavior. A constant head hydraulic conductivity apparatus was fabricated to measure the hydraulic conductivity of the tire shred sample under different axial strains. Further, the fabricated assembly was capable of measuring hydraulic conductivity of the sample at various sample locations at a given strain level. One aim of this study was to provide supporting information for permission to use tire chips as an alternative to crushed stone in the leachate collection system of a landfill. Shredded tires from two different sources were used in this study to investigate any differences in the sensitivity of the shredding process to compressibility and hydraulic conductivity responses under varied applied loads. Under applied vertical loads resulting in average vertical stresses of up to 440 kPa, equivalent to over 50 m of waste, the maximum normal strain recorded in each type of tire chip was observed to plateau at a strain level near or slightly greater than 0.5. The results of the permeability testing indicated average hydraulic conductivity values ranging between 0.67 and 13.4 cm/s under average applied normal stresses ranging from approximately 60 to 335 kPa and strain increments between 0.3 and 0.5. These results are one to three orders of magnitude higher than the hydraulic conductivity typically specified for drainage layers in leachate collection systems of 0.01 cm/s. Additional tests were also carried out to identify how landfill leachate and varied pH levels may affect the compressibility and hydraulic conductivity of the shredded tires. Care should be exercised in extending these results to field conditions, as the results presented are based on limited experimental testing data and a limited time frame.     

Characterization and leaching of NiCd and NiMH spent batteries for the recovery of metals

Since NiMH and NiCd batteries are still used in the electronic devices market, a treatment and recycling plant has many advantages both from the environmental and the economic points of view. Unfortunately, there is no relationship between shape, size and chemical composition of spent batteries, consequently the characterization and the leaching method of the starting material becomes an important step of the overall treatment process in choosing the best conditions for the selective separation of the metals by hydrometallurgy. Leaching at 20 degrees C with H(2)SO(4) 2M for about 2h seems to be a good solution in terms of cost and efficiency for both battery types. The hydroxide compounds can be readily leached while Ni present as metallic form requires more aggressive conditions due to kinetic constraints. In this paper, the characterization of NiMH and NiCd spent batteries and the results of leaching tests in different conditions are reported.     

Characterization and recovery of mercury from spent fluorescent lamps

Fluorescent lamps rely on mercury as the source of ultraviolet radiation for the production of visible light. Partitioning of mercury among vapor phase, loose phosphor powders produced during breaking and washing steps, glass matrices, phosphor powders attached on the glass and aluminum end caps was examined from simulated laboratory lamp recycling tests for different types of spent and new fluorescent lamps. Mercury concentrations in lamp glasses taken from commercial lamp recyclers were also analyzed for comparison with the simulated results of spent and new lamps of different types. The mercury content of the glass from spent lamps was highly variable depending on the lamp type and manufacturer; the median values of the mercury concentration in glasses for spent 26- (T8) and 38-mm (T12) diameter fluorescent lamps were approximately 30 and 45 microg/g, respectively. The average mercury concentration of samples taken from recycler A was 29.6 microg/g, which was about 64% of median value measured from the spent T12 lamps. Over 94% of total mercury in lamps remained either as a component of phosphor powders attached inside the lamp or in glass matrices. New T12 lamps had a higher partitioning percentage of elemental mercury in the vapor phase (0.17%) than spent T12 lamps (0.04%), while spent lamps had higher partitioning percentages of mercury resided on end-caps and phosphor powders detached from the breaking and washing steps. The TCLP values of simulated all lamp-glasses and samples obtained from recyclers were higher than the limit of LDR standard (0.025 mg/L). After investigating acid treatment and high temperature treatment as mercury reclamation techniques, it was found that heating provided the most effective mercury capture. Although the initial mercury concentrations of individual sample were different, the mercury concentrations after 1 h exposure at 100 degrees C were below 4 mug/g for all samples (i.e., <1% remaining). Therefore, it is recommended that heating be used for recovering mercury from spent fluorescent lamps.     

再生金属行业技术培训现状与创新

阐述了再生金属行业培训工作的发展现状,对我国再生金属行业员工培训工作的内容、特点、效果进行分析,并对今后培训工作提出建议和设想。     

制约中国废钢铁产业发展的主要因素

进入21世纪以来,我国的废钢铁回收、加工和综合利用业务,已经从传统的废钢铁加工业发展成为现代化的废钢铁产业.但由于没有形成强大的产业联盟,整体抗风险能力较差,影响了废钢铁产业的进一步发展针对这一现状,指出并分析了制约我国废钢铁产业发展的主要因素.     

Application of a gas-solid fluidized bed separator for shredded municipal bulky solid waste separation

A laboratory-scale gas-solid fluidized bed separator able to separate fractions of 5.6-50mm was used for separation of shredded municipal bulky waste (SBW) into combustibles and incombustibles. In batch-scale tests, it was found that accumulation of SBW in the bottom of the bed significantly reduced the separation efficiency. In this study, stirring was shown to be effective in preventing this accumulation. Flexible sheet materials such as paper and film plastics also significantly decreased the separation efficiency. In batch-scale tests, an overall efficiency of 90% was obtained when flexible materials such as film plastics and paper were excluded from the feed SBW. In continuous feeding tests, purities of the float and sink fractions attained 95% and 86% efficiencies, respectively, with an overall efficiency of 79%. The effect of feedstock shape on separation efficiency was also investigated. This study revealed that large particles can be properly separated on the basis of density, while the shape of the material significantly influenced behavior in the fluidizing bed.     

国内废钢行业概况及废钢价格关联因素的量化研究

介绍了"十五"和"十一五"时期国内废钢行业发展概况,重点阐述废钢行业的回收供应以及消耗情况,并对影响废钢价格的因素进行数学建模,对关联程度大小进行量化,对更好地分析废钢市场走势有较好的指导意义。     

我国废钢产业发展概况及前景展望

对我国2009年废钢供求状况、行情及我国废钢产业的发展进行回顾,展望了2010年国内废钢市场的发展前景,指出2010年我国废钢资源依然紧缺,不利于钢铁产业节能减排;新税收政策的实施以及中小钢铁企业的恶性竞争也是造成我国废钢资源紧缺的根本原因。     

产能过剩经济低迷困局下废钢产业的应对策略探讨

概述了目前国内外的经济环境状况,对我国钢铁产业和废钢产业面临的现状进行了分析总结,并提出应对策略;阐明了我国钢铁产业将进入相当长的低速微利发展期,钢铁产业转方式、调结构已迫在眉睫;废钢产业只有走专业化、规模化的发展道路,形成新的产业机制,才是废钢产业绿色健康发展的必然趋势.     

进口废塑料清洁程度定量化合格评定方法的探讨

目前国内对进口废塑料清洁程度的合格评定,长期以来一直采取感官检验的定性方法,引起了较多争议.以<进口可用作原料的固体废物环境保护控制标准--废塑料>(GB16487.12)为依据,分析了GB16487.12对进口废塑料清洁程度进行规定的原因,并在此基础上探讨了对进口废塑料清洁程度采取定量化的合格评定原理,提出参照<一般工业固体废物贮存、处置场污染控制标准>(GB18599)和<生活垃圾填埋污染控制标准>(GB16889)对进口废塑料清洁程度制定定量化限量要求,并建议尽快修订现行国家标准<进口可用作原料的固体废物环境保护控制标准--废塑料>.