Ambient aerosol sampling: Problems,goals and wind tunnel test results of hi-volume samplers

The area of ambient air sampling and its inherent problems and current goals are discussed in general. In particular, recently completed tests of the collection effectiveness of the Rocky Flats Hi-Volume Sampler are compared to previously completed tests of the Standard EPA Hi-Volume Sampler for a variety of field realistic conditions. Collection effectiveness is defined as the ratio of the aerosol collected on the collection substrates of the sampler to that collected by an isokinetic sampling system.The collection effectiveness of the Standard EPA Hi-Volume Sampler was determined as a function of particle size (5–50 μm) and sampler orientation (0° and 45°) at a base condition wind speed of 4.6 m/s and 8% relative turbulence intensity. The results indicated a strong effect of orientation on collection effectiveness at a sampling rate of 1416 l/min. Wind speed over the range of 1.5–4.6 m/s does not greatly influence the collection effectiveness of 15 μm particles. Free stream turbulence levels of 1 and 8% relative intensity has no effect upon collection characteristics.The collection effectiveness of the Rocky Flats Hi-Volume Sampler was determined as a function of particle size (1–34 μm), wind speed (1.52–12.19 m/s) and sampler orientation to the mean flow (0°, 45°, 180°). The results show the sampler, with an inlet flow rate of 880 l/min, has an inlet effectiveness that was a slight function of orientation angle for particles 1–10 μm with a larger effect seen for 20–34 μm; a strong effect of velocity was seen up to 5 m/s where a further increase showed only a slight decrease in effectiveness.The Microsorban-98 filter that is presently used in the Rocky Flats Sampler was tested for efficiency over the size range of particles from 0.01–1 μm and with three different face velocities using the sampler flow rates of 600, 800 and 1 000 l/min corresponding to pressure drops of 20–24 in. of water (3.74–4.49 cm HaG). The filter paper, which was of the fiber type, was found to be 99.9% efficient over the range of particle sizes and pressure drops tested.     

Recent IAEA intercomparison on the determination of trace elements in simulated air filters

Results of a recent intercomparison on the determination of trace elements in simulated air filter samples are reported. A large scatter of results is obtained for some elements and systematic differences between laboratories are observed. The performance of different methods, in particular neutron activation analysis and atomic absorption spectrophotometry, used by the various laboratories is discussed (air filter analysis; intercomparison; trace elements; control charts).     

Intercomparison of INAA and ICP-MS results for thorium determination in Pakistani diet

A pilot study on ingestion and organ content of trace elements of importance in radiological protection was to be carried out in Pakistan. Baseline analytical data on daily dietary intake of thorium was to be measured using Instrumental Neutron Activation Analysis (INAA) technique. To determine the accuracy and reliability of our technique, some samples were measured in Pakistan using INAA and in Japan using Inductively Coupled Plasma-Mass Spectrometry. For intercomparison of results overall mean Z-scores were calculated. The results showed validity of our technique. Mean value of 232Th concentration in Pakistani diet samples using INAA technique is 0.0062 +/- 0.0028 microg/g and with ICP-MS technique is 0.0069 +/- 0.0032 microg/g.     

Radon exhalation from granites used in Saudi Arabia

Measurements of radon exhalation for a total of 50 selected samples of construction materials used in Saudi Arabia were taken using a radon gas analyzer. These materials included sand, aggregate, cement, gypsum, hydrated lime, ceramics and granite. It was found that the granite samples were the main source of radon emanations. A total of 32 local and imported granite samples were tested. It was found that the radon exhalation rates per unit area from these granite samples varied from not detectable to 10.6 Bq m-2 h-1 with an average of 1.3 Bq m-2 h-1. The linear correlation coefficient between emanated radon and radium content was 0.92. The normalized radon exhalation rates from 2.0 cm thick granite samples varied from not detectable to 0.068 (Bq m-2 h-1)/(Bq kg-1) with an average of 0.030 (Bq m-2 h-1)/(Bq kg-1). The average radon emanation of the granite samples was found to be 21% of the total radium concentration. Therefore, granite can be a source of indoor radon as well as external gamma-radiation from the uranium decay series.     

Estimation of 222Rn release from the phosphogypsum board used in housing panels

Phosphogypsum board is a popular construction material used for housing panels in Korea. Phosphogypsum often contains (226)Ra which decays into (222)Rn through an alpha transformation. (222)Rn emanated from the (226)Ra-bearing phosphogypsum board has drawn the public concern due to its potential radiological impacts to indoor occupants. The emanation rate of (222)Rn from the board is estimated in this paper. A mathematical model of the emanation rate of (222)Rn from the board is presented and validated through a series of experiments. The back diffusion effect due to accumulation of (222)Rn-laden air was incorporated in the model and found to have a strong impact on the (222)Rn emanation characteristics.     

Experimental measurements of aerosol concentrations in offices

A new automated version of the piezoelectric microbalance measures the mass concentration of airborne particles smaller than a preselected aerodynamic cutoff diameter. It is designed for near-real-time, unattended, round-the-clock measurements of nearly any aerosol environment inhabited by humans. The instrument uses an electrostatic precipitator to deposit particles with greater than 95% efficiency onto a piezoelectric quartz crystal sensor which is able to detect a deposit of 0.005 μg. The precipitator and sensor are nearly identical to those in the portable instrument reported previously. Measurements comparing within ± 15% with gravimetrically measured filter samples are documented for a wide variety of aerosols in the 50 μg/m³ to 5.5 mg/m³ range. The instrument measures particles from 10 μm down to 0.01 μm in diameter, including submicron combustion smokes and metallic fumes. The piezoelectric microbalance technique senses the mass concentration of the aerosol, rather than light scattering properties as is done by photometers and nephelometers. The piezobalance, with 1 L/min sample flow, is more sensitive than any other mass-sensing instrument, making it especially suited for low concentration indoor measurements, even below 50 μg/m³. An automatic piezobalance recently measured respirable aerosol mass concentrations in several offices. Each measurement was the average concentration during a 30-min period. The 24-h/day measurements continued for several days. Especially interesting is the diurnal pattern, both for offices with and without smokers. The effect of a single nearby smoker was clearly illustrated when the smoker was absent one day in the middle of a week. Normal daytime peak concentrations in that office reached 80–110 μg/m³ with a smoker present, but only 50–60 μg/m³ when the smoker was absent. Curious smokers who briefly stopped byt o see the instrument caused single half-hour averages to triple, to values as high as 294 μg/m³ in one office.     

Assessment, validation and intercomparison of operational models for predicting tritium migration from routine discharges of nuclear power plants: the case of Loire River

During last decades, a number of projects have been launched to validate models for predicting the behaviour of radioactive substances in the environment. The project of the "Aquatic" working group of the project EMRAS (Environmental Modelling for Radiation Safety) organised by the International Atomic Energy Agency (IAEA) was based on the validation and assessment of models for predicting the behaviour of radionuclides in the aquatic ecosystems. The present paper describes a blind test of models aimed at assessing the dispersion of tritium releases in the Loire River (France), on a large domain ( approximately 350km) and on a period of six months, by comparing the results obtained by operational-to-experimental values of tritium concentration at Angers, a city along the Loire River. The common conclusion is that the models used by the different participants namely 1D models and models based on a schematic hydraulic (box models) are reliable tools for tritium transport modelling. Nevertheless, the importance of proper and detailed hydrological data for the appropriate prediction of pollutant migration in water is demonstrated by the example provided during this study.     

Preliminary results from the first national in situ gamma spectrometry survey of the United Kingdom

In situ gamma spectrometry was introduced as part of a national soil and herbage pollution survey of the United Kingdom (UK) in 2002, to evaluate its potential for complimenting or even replacing the conventional soil sampling approach in environmental monitoring. A total of 128 points were measured across the whole of the UK on a 50-km grid, including 11 calibration sites, encompassing a complete spectrum of soil types, geology and depositional environments. Good comparisons are demonstrated between in situ and soil sample derived estimates of environmental radioactivity from spatially matched sampling plans. Air kerma results and the contributions to air kerma rate are also presented and compared with calibrated conventional single parameter GM based instruments. The preliminary results are presented here and show that in situ gamma spectrometry provides a rapid and robust approach, providing spatially integrated estimates for environmental monitoring purposes.     

Seasonal variations of aerosol residence time in the lower atmospheric boundary layer

During a one year period, from Jan. 2002 up to Dec. 2002, approximately 130 air samples were analyzed to determine the atmospheric air activity concentrations of short- and long-lived (222Rn) decay products 214Pb and 210Pb. The samples were taken by using a single-filter technique and gamma-spectrometry was applied to determine the activity concentrations. A seasonal fluctuation in the concentration of 214Pb and 210Pb in surface air was observed. The activity concentrations of both radionuclides were observed to be relatively higher during the winter/autumn season than in spring/summer season. The mean activity concentration of 214Pb and 210Pb within the whole year was found to be 1.4+/-0.27 Bq m(-3) and 1.2+/-0.15 mBq m(-3), respectively. Different 210Pb:214Pb activity ratios during the year varied between 1.78 x 10(-4) and 1.6 x 10(-3) with a mean value of 8.9 x 10(-4) +/- 7.6 x 10(-5). From the ratio between the activity concentrations of the radon decay products 214Pb and 210Pb a mean residence time (MRT) of aerosol particles in the atmosphere of about 10.5+/-0.91 d could be estimated. The seasonal variation pattern shows relatively higher values of MRT in spring/summer season than in winter/autumn season. The MRT data together with relative humidity (RH), air temperature (T) and wind speed (WS), were used for a comprehensive regression analysis of its seasonal variation in the atmospheric air.     

Some results from the demonstration of indoor radon reduction measures in block basement houses

Active soil ventilation techniques have been tested in 26 block-wall basement houses in eastern Pennsylvania with significantly elevated indoor radon concentrations, generally above 740 Bq/m³, and the results indicate that radon levels can be reduced substantially often below the U.S. Environmental Protection Agency (EPA) guideline of 148 Bq/m³, if effective suction can be drawn on the soil underneath the concrete slabs of these houses. Such effective suction appears achievable when either: 1) the house has a complete loop of drain tile around its footings for water drainage purposes, and suction is drawn on that loop; or 2) a sufficient number of suction pipes can be inserted at the proper locations into the crushed rock or the soil underneath the slab.     

An integrated methodology for the used product selection problem faced by third-party reverse logistics providers

The rise of electronic commerce and the stricter government regulations on the recovery of end-of-life products increased the number of products returned by customers. A company may deal with increasing product returns by developing its own reverse logistic system. However, high fixed costs associated with dedicated reverse logistics equipment and infrastructure force many companies to outsource their reverse logistics operations to third-party reverse logistics providers. One of the important problems faced by third-party reverse logistics providers is the selection of the types of used products to be collected. In this study, a four-phase used product selection methodology is proposed. First, the quantitative and qualitative selection criteria are determined. Then the weights of the criteria are calculated using fuzzy analytic hierarchy process. Next, simulation models are employed to determine the values of quantitative criteria. Finally, technique for order preference by similarity to ideal solution ranks alternative used product types. A numerical example is also provided in order to present the applicability of the proposed methodology.     

Development of a new aerosol monitoring system and its application in Fukushima nuclear accident related aerosol radioactivity measurement at the CTBT radionuclide station in Sidney of Canada

A high volume aerosol sampler ("Grey Owl") has been designed and developed at the Radiation Protection Bureau, Health Canada. Its design guidance is based on the need for a low operational cost and reliable sampler to provide daily aerosol monitoring samples that can be used as reference samples for radiological studies. It has been developed to provide a constant air flow rate at low pressure drops (∼3 kPa for a day sampling) with variations of less than ±1% of the full scale flow rate. Its energy consumption is only about 1.5 kW for a filter sampling over 22,000 standard cubic meter of air. It has been demonstrated in this Fukushima nuclear accident related aerosol radioactivity monitoring study at Sidney station, B.C. that the sampler is robust and reliable. The results provided by the new monitoring system have been used to support decision-making in Canada during an emergency response.     

Monitoring microbial biomass and respiration in different soils from the Czech Republic--a summary of results

The microbial biomass (Cbio), respiration (basal respiration (BR) and potential respiration (PR)), and derived indices for 520 independent soil samples of 117 different soils from the Czech Republic were statistically analysed. The broad range of soil samples allowed the stepwise breakdown of the database into six reasonable categories of soil: arable soils, loamy grassland soils, sandy grassland soils with weak organic matter content, sandy grassland soils with moderate organic matter content, forest soils with moderate organic matter content, and forest organic soils with rich organic matter content. Because soil microbiology lacks benchmarking values, the ranges of the microbial characteristics for these categories were stated and are presented here. The separation into soil groups narrowed the ranges enough to be useful for comparative purposes. The groups displayed significant differences in basal microbial parameters. The lowest microbial biomass was found in arable soils and grassland sandy soils with weak organic matter content. The highest microbial biomass was shown by loamy grassland soils and organic forest soils. Respiration displayed similar results to the microbial biomass. The derived indices revealed less significant differences confirming their inner-standard nature. The relationships between the soil contamination and microbial parameters were not explored because of the confounding effect of soil organic matter. However, it was not shown by the category of grassland sandy soils with weak organic matter content suggesting they could be especially suitable for the biomonitoring of harmful effects of chemicals on soil microorganisms.     

An economic-environmental analysis of selected barrier-coating materials used in packaging food products: a Swedish case study

The purpose of a barrier coating in food packaging is primarily to increase the shelf life of the foodstuff contained within the packaging, preserve its colour, odour, taste and quality, and thereby reduce food wastage (both at retail outlets and households). While most publications hitherto have compared packaging and barrier-coating materials on the basis of their environmental impacts alone, this paper adopts a more holistic approach by factoring in the economic aspect as well. Four barrier material alternatives—starch, polyethylene, EVOH + kaolin and latex + kaolin are analysed. Two well-defined end-of-life handling scenarios, relevant to Sweden, are: one in which everything except starch is recycled, with starch being composted, and the other in which everything is incinerated. Among the several environmental impact categories which can be analysed, this paper considers only global warming. Two approaches are tested to combine the economic and environmental aspects—normalisation, weighting and aggregating on the one hand, and using the carbon tax to internalise the externality caused by GHG emissions on the other. For the set of weighting factors obtained thanks to a survey conducted by the authors (40.6% for environmental and 59.4% for economic), starch emerges as the most sustainable alternative, followed by polyethylene for both the end-of-life handling scenarios. This tallies with the result obtained by using the carbon tax for internalisation of the externality. The case study, methodology and results presented in this paper, will hopefully be a springboard for more detailed studies of this nature, under the umbrella of sustainability.     

Assessing radiation impact at a protected coastal sand dune site: an intercomparison of models for estimating the radiological exposure of non-human biota

This paper presents the application of three publicly available biota dose assessment models (the ERICA Tool, R&D128/SP1a and RESRAD-BIOTA) to an assessment of the Drigg coastal sand dunes. Using measured ⁹⁰Sr, ⁹⁹Tc, ¹³⁷Cs, ²³⁸Pu, ^239+240Pu and ²⁴¹Am activity concentrations in sand dune soil, activity concentration and dose rate predictions are made for a range of organisms including amphibians, birds, invertebrates, mammals, reptiles, plants and fungi. Predicted biota activity concentrations are compared to measured data where available. The main source of variability in the model predictions is the transfer parameters used and it is concluded that developing the available transfer databases should be a focus of future research effort. The value of taking an informed user approach to investigate the way in which models may be expected to be applied in practice is highlighted and a strategy for the future development of intercomparison exercises is presented.     

Heavy precipitation events over the Euro-Mediterranean region in a warmer climate: results from CMIP5 models

Possible changes in the intensity of heavy precipitation events at the end of the twenty-first century over the Euro-Mediterranean region are investigated, using a subset of numerical climate simulations taking part to the fifth phase of the Coupled Model Intercomparison Project (CMIP5). As a measure of the intensity associated with heavy precipitation events, we use the difference between the 99th and the 90th percentiles. Despite a slight tendency to underestimate the observed heavy precipitation intensity during summer and to overestimate it during winter, the considered CMIP5 models well represent the observed patterns of the defined 99th–90th percentile metric during both seasons for the 1997–2005 period over the Euro-Mediterranean region. Over the investigated domain, an increase of the width of the right tail of the precipitation distribution is projected in a warmer climate, even over regions where nearly the entire precipitation distribution becomes dryer. This is the case of the European domain within the 45N–55N belt.     

Using the useful: characteristics of used palms in south-eastern Ecuador

Plant families differ greatly with regard to their usefulness to humans. Within families there are also large differences in the usefulness between species; some are used for many different purposes, while most are used for few or no purposes. Which ones and to what extent species are used often varies between areas and cultural groups. To better understand variation in speciesȁ9 usefulness we studied the use of different palm species (Arecaceae) among two socio-cultural groups (one indigenous and one colonist group of mixed ethnic descent) living in the same area. We used regression and correlation analyses to determine to what degree use is related to ecological and morphological characteristics, to geographical differences in abundance, and to peopleȁ9s perceptions of speciesȁ9 availability. We found that abundance and height were the most important characteristics related to use, possibly due to the effect of height and abundance on salience, search time, and (for height) suitability for different purposes. Abundance was most important for palm heart extraction, probably due to the opportunistic nature of this activity. There was no difference between socio-cultural groups with regard to the relationship between palm abundance and use, but abundance seemed to be more decisive for people who used moderate amounts of palms. Finally, it was seen that peopleȁ9s estimates of palm abundance were not related to our measurements of abundance, which may be due to use of different spatial scales in evaluating abundance and to the subjective nature of terms such as “rare” and “abundant”.     

Pre-concentration of naturally occurring radionuclides and the determination of (212)Pb from fresh waters

A novel technique has been developed for determining the ²¹²Pb activity of fresh waters. This is of interest to environmental monitoring programmes that utilise gross α-activity methods to screen for anthropogenic radionuclides. The contribution from ²¹²Pb varies, and is difficult to experimentally measure due to its relatively short half-life (t_½ = 10.6 h) and low environmental activity (<0.1 Bq l⁻¹). The use of a three-stage technique that encompasses a unique form of pre-concentration, separation and analysis by liquid scintillation counting allows a lower detection limit of 0.006 Bq l⁻¹ with a chemical yield of 92.5 ± 5.6%. The measurement can be obtained within 7 h of sample collection, and is calculated using the radioactive decay of ²¹²Bi. Other naturally occurring radionuclides may also be extracted using the pre-concentration stage of the technique, with efficiencies above 90% at a range of pH values.     

In situ gamma-ray spectrometry in forests: determination of kerma rate in air from 137Cs

Continental margins are important areas to be considered when studying the distributions and depositions of pollutants, both conventional and radioactive. Coastal sediments accumulate most of those contaminants which can be introduced following atmospheric and/or fluvial pathways. Moreover, their residence times within the water column are usually shortened due to their affinity to associate with the downward falling particulate matter, more abundant at shallower depths. In this paper the distribution profiles and inventories of plutonium, americium and cesium are detailed, providing useful information about recent sedimentation phenomena such as sediment mixing, slumping processes and bioturbation. Unsupported 210Pb data are used as reliable indicators of enhanced/reduced deposition events. Also, the calculated inventories have enabled the estimation of the radiological contribution of the Spanish Mediterranean margin to the total radioactivity deposited onto the Mediterranean sea floor.     

Quantitative evaluation of XAD-8 and XAD-4 resins used in tandem for removing organic solutes from water

The combined XAD-8 and XAD-4 resin procedure for the isolation of dissolved organic solutes from water was found to isolate 85% or more of the organic solutes from Lake Skjervatjern in Norway. Approximately 65% of the dissolved organic carbon (DOC) was first removed on XAD-8 resin, and then an additional 20% of the DOC was removed on XAD-4 resin. Approximately 15% of the DOC solutes (primarily hydrophilic neutrals) were not sorbed or concentrated by the procedure. Of the 65% of the solutes removed on XAD-8 resin, 40% were fulvic acids, 16% were humic acids, and 9% were hydrophobic neutrals. Approximately 20% of the hydrophilic solutes that pass through the XAD-8 resin were sorbed solutes on the second resin, XAD-4 (i.e., they were hydrophobic relative to the XAD-4 resin). The fraction sorbed on XAD-4 resin was called XAD-4 acids because it represented approximately 85–90% of the hydrophilic XAD-8 acid fraction according to the original XAD-8 fractionation procedure. The recovery of hydrophobic acids (fulvic acids and humic acids) and the hydrophobic neutral fraction from XAD-8 resin was essentially quantitative at 96%, 98%, and 86%, respectively. The recovery of XAD-4 acids from the XAD-4 resin was only about 50%. The exact reason for this moderately low recovery is unknown, but could result from π-π bonding between these organic solutes and the aromatic matrix of XAD-4. The hydrophobic/hydrophilic solute separation on XAD-8 resin for water from background Side A and Side B of the lake was almost identical at 65 and 67%, respectively. This result suggested that both sides of the lake are similar in organic chemical composition even though the DOC variation from side to side is 20%.