Treatment of oily refinery wastes using a dissolved air flotation process

Refinery wastewater from Moustorod oil refinery, Cairo, Egypt, was treated by chemical coagulation. This step was followed by rapid solid-liquid separation using flotation under pressure of 4 atm. A flotation tank was designed for this purpose. Gas liquid chromatography was used for determination and identification of hydrocarbon compounds in refinery wastewater. The treatment technique proved to be very promising for reducing the hydrocarbon compounds, as well as other pollutants, to a very low concentration. The results obtained showed that some of the hydrocarbon compounds were completely removed.     

Biodegradability of hydrocarbons in the refinery wastewater from moustorod oil refinery

The present investigation deals with the study of hydrocarbon degradation present in refinery wastewater by natural microbial flora in addition to that obtained using Ps. aeruginosa under laboratory conditions. Results indicated that Ps. aeruginosa may have a significant role in the degradation of hydrocarbons. After seven days, several of the compounds in the original wastewater were completely degraded and four compounds (n-paraffins) were partially degraded. Without Ps. aerruginosa, the same picture had been obtained after 23 days.     

Treatment of wastewater by natural systems

Experimental results from a pilot-scale constructed wetland (CW) treatment plant have been described. The study was conducted at two different systems: continuous and batch. In the continuous system, the treatment yields were monitored in different loading conditions in 1-year period. The pilot plant consists of two serially connected tanks settled up with fillers; Cyperus was used as treatment media and wastewater between the two tanks was recycled periodically. Chemical oxygen demand (COD) and suspended solid (SS) removal efficiencies were obtained as 90% and 95%, respectively. The effluent COD concentration at an average loading of 122 g COD/m2 day was satisfactory for the Turkish Water Pollution Control Regulation. This means that a 0.8 m2 of garden area per person is required. Other removal values for the same conditions were as follows: total Kjeldahl nitrogen (TKN) was 77%, total nitrogen (TN) was 61%, and PO4(3-) -P was 39%. The batch experimental systems consist of 12 pairs of serially connected tanks, with each pair having a surface area of 1 m2. Each set was filled with sewage once a day, and the wastewater between the paired tanks was recycled periodically by the pump. Each pair of tanks was filled with materials such as gravel, peat, and perlite. Seven of them were vegetated with Phragmites, Cyperus, Rush, Iris, Lolium, Canna, and Paspalum, while the other five were not seeded. The best performances were obtained by Iris for COD (% 94), by Canna for ammonia nitrogen (% 98), and by Iris for total nitrogen (% 90) and phosphorus (% 55) removal.     

Measuring the antioxidant activity of olive oil mill wastewater using chemiluminescence

A sensitive and simple procedure is described for determining the total phenolic/antioxidant levels of olive oil mill wastewater (OMW), using for the first time Co(II)/ethylenediaminetetracetic acid (EDTA)-induced luminol chemiluminescence. Olive oil wastewater samples were tested for their composition in simple phenolic compounds as a function of the extraction system (two- and three-phase centrifugation systems). The results revealed that the three-phase system had a stronger antioxidant activity and a higher total phenolic content than the two-phase system. The relationship between antioxidant values and total phenolic content is also discussed.     

Treatment of sugar industry wastewater using a combination of thermal and electrocoagulation processes

Sugar industries require a large amount of water for processing, and also generate large amounts of high-degree polluted wastewater. To maintain the water balance in the industry, it is imperative that effective treatment methods need to be devised to treat the wastewaters. The main aim of the present work is to treat the sugar industry wastewater by combined thermal and electro-oxidation methods with a metal and a catalyst based on ferrous material. Results showed a reduction of 75.6% of COD and 79.2% of colour content with thermal treatment, and 97.8% of COD and 99.7% of colour with combined thermal and electrocoagulation treatments under optimum conditions. These reduction levels are adequate for recycling limits.     

Fate of oil from two major oil spills: Role of microbial degradation in removing oil from the Amoco Cadiz and IXTOC I spills

The fate of oil was examined in intertidal sediments impacted by the Amoco Cadiz spill in Brittany, France, and in surface waters contaminated by the IXTOC I well blowout in the Bay of Campeche, Mexico. The role of microbial degradation in removing the contaminating hydrocarbons was assessed by laboratory determinations of numbers of hydrocarbon utilizing microorganisms, measurement of microbial hydrocarbon biodegradation potentials, by chemical analyses of samples incubated under controlled conditions and by examination of the evolution of the hydrocarbon mixture in field samples collected after the spill. Analyses included the use of ¹⁴C radiolabelled hydrocarbon tracers, glass capillary-gas chromatography and mass spectrometry. Numbers of hydrocarbon utilizing microorganisms were found to be elevated by several orders of magnitude in oil contaminated samples. Numbers of hydrocarbon utilizing microorganisms appear to provide a useful index of environmental hydrocarbon contamination. However, environmental constraints on microbial processes appear to be most important in determining actual rates of biodegradation rather than numbers of available hydrocarbon utilizing microorganisms. Very high rates of degradation were found in intertidal sediments impacted by the Amoco Cadiz spill. In contrast, rates of degradation in the Gulf of Mexico were found to be much lower, partly due to nutrient limitations and partly due to the formation of large masses of oil-water emulsion or mousse.     

Triclosan in wastewaters and biosolids from Australian wastewater treatment plants

Triclosan (TCS) is an antimicrobial agent widely used in many personal care products. This study investigated the occurrence of TCS in effluents, biosolids and surface waters, and its fate in wastewater treatment plants (WWTPs). The aqueous concentrations of TCS in nineteen effluents from Australian WWTPs ranged from 23 ng/L to 434 ng/L with a median concentration of 108 ng/L, while its concentrations in nineteen biosolids ranged from 0.09 mg/kg to 16.79 mg/kg on dry weight basis with a median concentration of 2.32 mg/kg. The removal rates for TCS in five selected WWTPs were found to range between 72% and 93%. Biological degradation was believed to be the predominant removal mechanism for TCS in the WWTPs. However, adsorption onto sludge also played a significant role in the removal of TCS in the WWTPs. TCS at concentrations up to 75 ng/L was detected in surface waters (outfall, upstream, and downstream) from five rivers receiving effluent discharge from WWTPs. Preliminary risk assessment based on the worst-case scenario showed that the TCS concentrations in surface waters might lead to risks to aquatic organisms such as algae. Based on the TCS levels in the biosolids, application of biosolids on agricultural land may also cause adverse effects in the soil environment.     

Improved oxidative stability of biodiesel via alternative processing methods using cottonseed oil

Biodiesel from waste cooking oil (WCO) requires antioxidants to meet oxidation stability specifications set forth in ASTM D6751 or EN 14214. In contrast, unrefined cottonseed oil (CSO), containing tocopherols and gossypol, produces biodiesel of higher oxidation stability. However, only a portion of these CSO endogenous antioxidants are suspected to be retained in biodiesel. Because the economics of biodiesel manufacturing rely upon inexpensive sources of triglycerides, emphasis was placed on developing improved alternative processing methods where WCO was the main source of methyl esters (WCOME) and CSO was used as a supplemental source of triglycerides and antioxidants in a 4:1 ratio. This study compared four processing methods for their ability to produce biodiesel of increased oxidative stability prepared from a 4:1 ratio of WCO:CSO. Two novel processing methods developed for this study utilise solvent properties of fatty acid methyl esters and glycerol to avoid additional chemical inventory for biodiesel processors. This study concludes that the two new processing methods resulted in biodiesel that had statistically significant improved oxidation stability when compared to two common industrial processing methods. Another significant finding is that high-shear homogenisation during transesterification reduced reaction time from the published one hour to 16 minutes.     

Fifteen-year trends in criteria air pollutants in oil sands communities of Alberta,Canada

An investigation of ambient air quality was undertaken at three communities within the Athabasca Oil Sands Region (AOSR) of Alberta, Canada (Fort McKay, Fort McMurray, and Fort Chipewyan). Daily and seasonal patterns and 15-year trends were investigated for several criteria air pollutants over the period of 1998 to 2012. A parametric trend detection method using percentiles from frequency distributions of 1 h concentrations for a pollutant during each year was used. Variables representing 50th, 65th, 80th, 90th, 95th and 98th percentile concentrations each year were identified from frequency distributions and used for trend analysis. Small increasing concentration trends were observed for nitrogen dioxide (< 1 ppb/year) at Fort McKay and Fort McMurray over the period consistent with increasing emissions of oxides of nitrogen (ca. 1000 tons/year) from industrial developments. Emissions from all oil sands facilities appear to be contributing to the trend at Fort McKay, whereas both emissions from within the community (vehicles and commercial) and oil sands facility emissions appear to be contributing to the trend at Fort McMurray. Sulfur dioxide (SO₂) emissions from industrial developments in the AOSR were unchanged during the period (101,000 ± 7000 tons/year; mean ± standard deviation) and no meaningful trends were judged to be occurring at all community stations. No meaningful trends occurred for ozone and fine particulate matter (PM_2.5) at all community stations and carbon monoxide at one station in Fort McMurray. Air quality in Fort Chipewyan was much better and quite separate in terms of absence of factors influencing criteria air pollutant concentrations at the other community stations.     

Distribution of PBDEs in air particles from an electronic waste recycling site compared with Guangzhou and Hong Kong, South China

Air samples of total suspended particles (TSP, particles less than 30-60 microm), and particles with aerodynamic diameter smaller than 2.5 microm (PM(2.5)) were collected simultaneously at Guiyu (an electronic waste recycling site), three urban sites in Hong Kong and two urban sites in Guangzhou, South China from 16 August to 17 September 2004. Twenty-two PBDE congeners (BDE-3, -7, -15, -17, -28, -49, -71, -47, -66, -77, -100, -119, -99, -85, -126, -154, -153, -138, -156, -184, -183, -191) in TSP and PM(2.5) were measured. The results showed that the overall average concentrations of TSP and PM(2.5) collected at Guiyu were 124 and 62.1 microg m(-3), respectively. The monthly concentrations of the sum of 22 BDE congeners contained in TSP and PM(2.5) at Guiyu were 21.5 and 16.6 ng m(-3), with 74.5 and 84.3%, contributed by nine congeners (BDE-28, -47, -66, -100, -99, -154, -153, -183 and -191 respectively). This pattern was similar to Tsuen Wan site of Hong Kong. Two urban sites of Guangzhou had the same congener pattern, but were different from Yuen Long and Hok Tsui sites of Hong Kong. The results also showed that the amount of mono to penta brominated congeners, which are more toxic, accounted for 79.4-95.6% of Sigma(22)PBDEs from all sites. All congeners tested in Guiyu were up to 58-691 times higher than the other urban sites and more than 100 times higher than other studies reported elsewhere. The higher concentration in the air was due to heating or opening burning of electronic waste since PBDEs are formed when plastics containing brominated flame retardants are heated.     

Selection of an effective sludge dewatering system for a small wastewater treatment plant

The Jahra Plant was commissioned in 1981 as a secondary treatment plant employing the extended aeration process. The plant has been upgraded since that time by constructing additional tertiary filtration units to improve effluent quality. The plant has a design capacity of 66 000 m³/d. At present, the daily inflow to the plant is about 47 000 m³/d of domestic sewage. The sludge produced at the Jahra Plant can be classified as excess activated sludge which combines the primary and secondary solids. At present, there are 30 drying beds receiving about 100 m³ of sludge dally. Sewage-sludge production represents about 0.5% of the total flow treated at the plant and is increasing yearly with increases in population and water consumption. Present dewatering systems are not adequate to cope with expansion in sewage treatment. Increasing the capacity of the existing plant would require more drying beds that could exacerbate existing odor problems. Some dewatering systems, such as the belt filter press and the centrifuge, have been tested to determine the most effective one under local conditions. Appropriate polymer doses for thickening have been determined. This paper describes present sludge dewatering units and operating techniques which have been developed during the operation of this facility.     

The relationship of dissolved Pb to some dissolved trace metals (Al, Cr, Mn, and Zn) and to dissolved nitrate and phosphate in a freshwater aquatic system in Mauritius

The relationship of some dissolved trace metals (Al, Cr, Mn, Zn, and Pb) with one another and to dissolved phosphate and nitrate in a freshwater aquatic system at Flic en Flac and Grand River North West (GRNW) in Mauritius (1850 km2, 20 degrees S and 57 degrees E, Western Indian ocean) is reported following trace metal determination using inductively coupled plasma mass spectrometry (ICP-MS). Dissolved Al (<200 ng ml(-1)), Cr (<50 ng ml(-1)), Mn (<50 ng ml(-1)), Zn (< 100 ng ml(-1)), and Pb (<50 ng ml(-1)) upstream, downstream GRNW and in the marshes and rivulet at Flic en Flac were found to be below the recommended EEC maximum admissible concentrations and within the ambient drinking water quality standards in Mauritius. Dissolved Pb was significantly positively correlated to both dissolved Cr and Zn suggesting that the cycling for dissolved Pb is linked to the cycling of both dissolved Cr and Zn along GRNW. The common influential cycling of Pb and Zn was further reinforced as both dissolved Pb and Zn were significantly positively correlated to dissolved phosphate, which suggested a biological role in the cycling of Zn and Pb. The role of biological activity or adsorption to biological systems in Pb cycling along GRNW is further suggested as dissolved Pb was significantly correlated to dissolved nitrate. The apparent absence of the dissolved Al, Cr, and Mn with dissolved nitrate and phosphate could be attributed to factors such as the lower sensitivity of the GRNW to metal uptake during biological activity during the time frame considered. The cycling of dissolved Al and Mn was also not linked to the cycling of Cr, Zn, and Pb as no significant correlation was found along GRNW.     

Occurrence and degradation of butyltins and wastewater marker compounds in sediments from Barcelona harbor, Spain

Contamination of Barcelona harbor sediments was assessed by the quantitative determination of butyltins (TBT, DBT and MBT) and surfactant intermediates, namely linear alkylbenzenes (LABs) and nonylphenols (NPs), as markers of urban and industrial wastewater contamination, respectively. Degradation indexes of TBT and LABs were calculated. Tributyltin predominated in the whole area over its degradation products, ranging from 98 to 4702 ng Sn/g. These elevated concentrations reveal a persistent historical contamination and a moderate degradation (BT(deg)). Moreover, the high LAB concentrations (1.2-53.1 microg/g) compared to the relatively low NP levels (3.8-72.0 ng/g) suggest a predominance of urban over industrial wastewater inputs, although a significant correlation (r(2) = 0.82, N = 12, P = 0.001) between LABs and NPs was found. Stormwater runoff and combined sewer overflows (CSO) were likely the most possible sources for both surfactant intermediates. The high degradation index values obtained for LABs could indicate an improvement in the wastewater management reducing its recent discharge into the Barcelona harbor area.     

Pharmaceuticals in soils of lower income countries: Physico-chemical fate and risks from wastewater irrigation

Population growth, increasing affluence, and greater access to medicines have led to an increase in active pharmaceutical ingredients (APIs) entering sewerage networks. In areas with high wastewater reuse, residual quantities of APIs may enter soils via irrigation with treated, partially treated, or untreated wastewater and sludge. Wastewater used for irrigation is currently not included in chemical environmental risk assessments and requires further consideration in areas with high water reuse. This study critically assesses the contemporary understanding of the occurrence and fate of APIs in soils of low and lower-middle income countries (LLMIC) in order to contribute to the development of risk assessments for APIs in LLMIC. The physico-chemical properties of APIs and soils vary greatly globally, impacting on API fate, bioaccumulation and toxicity. The impact of pH, clay and organic matter on the fate of organic ionisable compounds is discussed in detail. This study highlights the occurrence and the partitioning and degradation coefficients for APIs in soil:porewater systems, API usage data in LLMICS and removal rates (where used) within sewage treatment plants as key areas where data are required in order to inform robust environmental risk assessment methodologies.     

The radiological impact of atmospheric emissions from oil shale retorts

The radionuclide content of various oil shales, shale oils, and retorting waste products has been studied to determine the extent to which the development of this energy resource may perturb the natural radiation environment. Nearly all of the radioactivity in the raw shale is found in the spent shale after retorting. A primary exposure pathway to the public from this radioactivity will be through the release of particulate matter to the atmosphere during various mining, crushing, and retorting operations. Since the activity of this material is close to that of normal soil, however, the expected radiological impact is small.     

Studies on process optimization of biodiesel production from waste cooking and palm oil

This work investigated the optimisation of biodiesel production from waste cooking oil (WCO) and palm oil using a two-step transesterification process for WCO and base catalysed transesterification for palm oil. Transesterification reactions were carried out to investigate the effects of prepared catalyst CaO, methanol/WCO and methanol/palm oil ratio and temperature on the yield of biodiesel. A series of experiments were conducted to determine the best conditions for biodiesel production, using methanol/oil ratio between 4:1 and 11:1 and contact time varying between 2 and 4 h. Biodiesel yield of around 90 and 70% was obtained for palm and waste cooking oil at the methanol/oil ratios of 6:1 and 8:1 at temperature of 60 °C for reaction time of 4 h using prepared CaO as catalyst. The physicochemical properties of palm and WCO biodiesel were carried out using standard methods, while the fatty acid profile was determined using gas chromatography. The investigation concludes that biodiesel obtained from palm and waste cooking oil was within the specified limit.     

Local air quality management as a risk management process: assessing, managing and remediating the risk of exceeding an air quality objective in Great Britain

Air quality is managed in Great Britain via an effects-based, risk management process designed to provide a dynamic solution to public health issues associated with elevated concentrations of seven specified air pollutants. This paper is concerned with an examination and evaluation of the process of Local Air Quality Management (LAQM) in Great Britain from the late 1980s to date as a risk management process. The statutory basis of LAQM process is provided by the Environment Act 1995. The Act provides a framework in which national and local actions are required to identify and remediate areas of poor air quality. Within this framework, the implementation of the process at national and local levels is considered, leading to an identification and assessment of risks in the formulation and implementation of air quality management policy and practice. Local Authorities began the process of Review and Assessment in 1999 and the first round of the process concluded in 2001. Following this, some 129 Local Authorities declared one or more Air Quality Management Areas (AQMAs). The Review and Assessment elements of the framework were subjected to an evaluation in 2001 and the essential elements of it were confirmed as fit for purpose. The evaluation led to a confirmation of the process of LAQM but also a simplification based on the experience of Round 1. Now, a two step process is required comprising of an Updating and Screening Assessment and, where a risk of exceeding an Air Quality Objective (AQO) is identified, a Detailed Assessment follows. The Government has identified a time scale for Review and Assessment through to 2010 and also introduced the requirement of a regular Progress Report in order that a Local Authority is able to address routine matters of air quality management. The risks inherent in epidemiological or scientific uncertainty are factored into the LAQM process at an early stage of the process and, by identifying the risks and subjecting them to regular review, the process provides a 'level playing field' across spatial and temporal scales. Whilst the process of LAQM described in this paper has been developed for Great Britain, the generic elements of the process are applicable to other countries challenged by air pollution problems which require both national and local action to resolve them.     

The influence of ventilation on indoor/outdoor air contaminants in an office building

The air quality in a newly built preschool was investigated in a longitudinal study. Typical air contaminants emanating from building materials were determined, their variation over time (0–18 months) was measured, and the influence of the ventilation system (81%–91% recirculation of return air) on contaminant concentrations was studied. Volatile organic compounds were sampled by adsorption on porous polymer, analysed by a GC/FID system, and identified by MS. A spatial build-up in concentration (ppb or μg/m³ levels) is evident for all the organic compounds, as well as for CO₂, from the outdoor air, through the ventilation system, and through the rooms to the exhaust air. The longitudinal comparison over time shows that all the organic compounds decline in concentration mainly within the first 6 months of occupancy: 1-butanol 4–14 times, toluene and pentanal + hexanal 2–4 times, while formaldehyde remained at a constant low level of 90 ppb (110 μg/m³). It is difficult to believe that the problems of poor air quality in 100 preschools in Stockholm are caused by the organic compounds alone unless interactions occur. A preschool building needs to be gassed off during the first 6 months after its construction with no recirculation of return air allowed (outdoor air rate approx 4–5 ach). During at least 1–2 additional years, it is desired that the recirculation rate of return air is restricted, perhaps to 50%.