生命周期评价与环境影响评价的应用比较

生命周期评价(LCA)被誉为21世纪最有潜力的环境管理工具,它充分考虑了时间因素.环境影响评价(EIA)在我国已经发展起来,它作为企业或项目实施必需的一个环节,充分考虑了空间因素.通过对生命周期评价定义、发展的介绍,将其与环境影响评价相比较,提出将两种方法发展成为一种四维的、新的、更加全面的环境管理和评价方法.     

产业生态学与循环经济的比较分析

为了应对环境污染和资源短缺的问题,人类提出了可持续发展的战略,循环经济和产业生态学理论由此应运而生,并成为当今社会的热点问题.但由于两个概念理念相似,加之被频繁、反复地提出,很容易使两者相互混淆,两者的关系到底如何值得探讨.通过对两者进行分析比较,运用辩证法,得出结论:产业生态学是循环经济最坚实的基础,最有力的支撑,它的实践是实现循环经济的必要条件,而循环经济是对产业生态学内容的一次扩充和发展,是更好地实现产业生态学的新方法和新途径.     

火电厂SCR脱硝还原剂的选择与比较

从脱硝还原剂氨站的安全性、技术成熟性和应用广泛性、初投资和运行费用等方面对几种SCR脱硝还原剂进行了比较,结果表明：纯氨法的建造、运行成本较低,一般情况下,宜采用纯氨为脱硝剂。     

脱硫增效剂在湿法FGD系统的应用与比较

介绍了某电厂300 MW机组FGD装置在相同试验工况安排下分别使用三家公司提供的脱硫增效剂的试验情况,其脱硫率均有不同程度的提升,钙硫比显著降低,石膏浆液及石膏产品品质有所提高.说明使用脱硫增效剂后,在正常运行负荷范围内,不仅能优化系统参数,而且可以停一台浆液循环泵运行,降低系统电耗.     

覆膜滤料与常规滤料的性能测试及比较

随着污染物排放标准的日趋严格，覆膜滤料以其优良的过滤性能引起了人们的关注。针对覆膜滤料的过滤机理、过滤效率、过滤阻力、过滤风速等性能指标的研究现状进行了分析，并与常规针刺毡滤料进行了比较，指出了覆膜滤料的一些主要性能优势，以供实际选用时参考。     

三维与二维电解工艺处理丙烯腈废水的效果比较

采用三维电解工艺和二维电解工艺处理高浓度丙烯腈废水。实验结果表明:三维电解工艺对COD、TOC、TN和总凯氏氮(TKN)的去除率分别为45.32%、59.55%、61.42%和59.24%,二维电解工艺对COD、TOC、TN和TKN的去除率分别为32.65%、43.53%、46.04%和46.08%;三维电解工艺去除单位COD的能耗为2.72 kW·h/kg,二维电解工艺为1.52 kW·h/kg;三维电解工艺和二维电解工艺的出水BOD_5/COD分别由原水的0.14提高至0.38和0.29。三维电解工艺具有较高的去除率,但能耗也较高。在实际应用中可根据具体情况选择所采用的工艺。     

生物絮凝法与化学絮凝法处理洗毛废水的比较

分别采用生物絮凝法和化学絮凝法处理300 mL COD为20 000 mg/L、SS为4 000 mg/L的洗毛废水,最佳生物絮凝条件:生物絮凝剂加入量为5 mL,反应温度为30℃,先以120 r/min搅拌5 min、再以60 r/min搅拌35 min,洗毛废水pH为9.0.COD去除率达92%.最佳化学絮凝条件:化学絮凝剂加入量为30 mL,反应温度为40℃,先以120 r/min搅拌5 min、再以60 r/min搅拌25 min,洗毛废水pH为5.0.COD去除率达93%.生物絮凝剂和化学絮凝剂对洗毛废水的絮凝效果接近,但生物絮凝剂的加入量比化学絮凝剂少很多.     

微波焙烧法与马弗炉焙烧法处理废脱硝催化剂的效果比较

用Na_2CO_3作为助溶剂、Na_2O_2作为消解剂,采用微波焙烧法和马弗炉焙烧法消解处理废钒钨钛脱硝催化剂。通过XRF、BET、XRD和NH_3-TPD技术对两种消解方法制得的钛钨粉样品进行了表征。表征结果显示,与马弗炉焙烧法相比,微波焙烧法得到的钛钨粉纯度更高,TiO_2与WO_3含量之和大于96.7%(w),且该钛钨粉还具有更高的比表面积和酸性,可以作为钒钨钛脱硝催化剂的生产原料再利用。     

Landfill aeration in the framework of a reclamation project in Northern Italy

In situ aeration by means of the Airflow technology was proposed for landfill conditioning before landfill mining in the framework of a reclamation project in Northern Italy. A 1-year aeration project was carried out on part of the landfill with the objective of evaluating the effectiveness of the Airflow technology for landfill aerobization, the evolution of waste biological stability during aeration and the effects on leachate and biogas quality and emissions.The main outcomes of the 1-year aeration project are presented in the paper.The beneficial effect of the aeration on waste biological stability was clear (63% reduction of the respiration index); however, the effectiveness of aeration on the lower part of the landfill is questionable, due to the limited potential for air migration into the leachate saturated layers.During the 1-year in situ aeration project approx. 275 MgC were discharged from the landfill body with the extracted gas, corresponding to 4.6 gC/kgDM. However, due to the presence of anaerobic niches in the aerated landfill, approx. 46% of this amount was extracted as CH₄, which is higher than reported in other aeration projects. The O₂ conversion quota was lower than reported in other similar projects, mainly due to the higher air flow rates applied.The results obtained enabled valuable recommendations to be made for the subsequent application of the Airflow technology to the whole landfill.     

曝气强化非离子表面活性剂洗涤法修复柴油污染土壤

采用异位修复法,利用非离子表面活性剂洗涤柴油污染土壤,并在洗涤过程中曝气强化。考察了洗涤效果的影响因素,并通过表面张力和接触角的测定探讨了洗涤机理。实验结果表明:曝气对污染土壤中柴油的洗脱有强化作用,可提高洗脱率10%~20%;3种非离子表面活性剂的洗脱效果优劣次序为聚氧乙烯月桂醚(Brij-35)曲拉通X-100(TX-100)吐温-80(Tw-80);在表面活性剂浓度为1倍临界胶束浓度、曝气量为7.5 L/min、洗涤时间为60 min、洗涤液pH为11.0的优化条件下,Brij-35对柴油的洗脱率达77.4%,污染土样的含油率从7.0%降至1.6%,接触角从24.12°降至6.65°,可基本恢复土壤的亲水性;洗涤液的表面张力随表面活性剂浓度的增加而降低,但不受洗涤液pH的影响。     

Numerical simulation of landfill aeration using computational fluid dynamics

The present study is an application of Computational Fluid Dynamics (CFD) to the numerical simulation of landfill aeration systems. Specifically, the CFD algorithms provided by the commercial solver ANSYS Fluent 14.0, combined with an in-house source code developed to modify the main solver, were used. The unsaturated multiphase flow of air and liquid phases and the biochemical processes for aerobic biodegradation of the organic fraction of municipal solid waste were simulated taking into consideration their temporal and spatial evolution, as well as complex effects, such as oxygen mass transfer across phases, unsaturated flow effects (capillary suction and unsaturated hydraulic conductivity), temperature variations due to biochemical processes and environmental correction factors for the applied kinetics (Monod and 1st order kinetics). The developed model results were compared with literature experimental data. Also, pilot scale simulations and sensitivity analysis were implemented. Moreover, simulation results of a hypothetical single aeration well were shown, while its zone of influence was estimated using both the pressure and oxygen distribution. Finally, a case study was simulated for a hypothetical landfill aeration system. Both a static (steadily positive or negative relative pressure with time) and a hybrid (following a square wave pattern of positive and negative values of relative pressure with time) scenarios for the aeration wells were examined. The results showed that the present model is capable of simulating landfill aeration and the obtained results were in good agreement with corresponding previous experimental and numerical investigations.     

Odorous gaseous emissions as influence by process condition for the forced aeration composting of pig slaughterhouse sludge

Compost sustainability requires a better control of its gaseous emissions responsible for several impacts including odours. Indeed, composting odours have stopped the operation of many platforms and prevented the installation of others. Accordingly, present technologies collecting and treating gases emitted from composting are not satisfactory and alternative solutions must be found. Thus, the aim of this paper was to study the influence of composting process conditions on gaseous emissions. Pig slaughterhouse sludge mixed with wood chips was composted under forced aeration in 300 L laboratory reactors. The process conditions studied were: aeration rate of 1.68, 4.03, 6.22, 9.80 and 13.44 L/h/kg of wet sludge; incorporation ratio of 0.55, 0.83 and 1.1 (kg of wet wood chips/kg of wet sludge), and; bulking agent particles size of <10, 10 < 20 and 20 < 30 mm. Out-going gases were sampled every 2 days and their composition was analysed using gas chromatography coupled with mass spectrometry (GC–MS). Fifty-nine compounds were identified and quantified. Dividing the cumulated mass production over 30 days of composting, by odour threshold, 9 compounds were identified as main potential odour contributors: hydrogen sulphide, trimethylamine, ammonia, 2-pentanone, 1-propanol-2-methyl, dimethyl sulphide, dimethyl disulphide, dimethyl trisulphide and acetophenone. Five gaseous compounds were correlated with both aeration rate and bulking agent to waste ratio: hydrogen sulphide, trimethylamine, ammonia, 2-pentanone and 1-propanol-2-methyl. However, dropping the aeration rate and increasing the bulking agent to waste ratio reduced gaseous odour emissions by a factor of 5–10, when the required threshold dilution factor ranged from 10⁵ to 10⁶, to avoid nuisance at peak emission rates. Process influence on emissions of dimethyl sulphide, dimethyl disulphide, dimethyl trisulphide were poorly correlated with both aeration rate and bulking agent to waste ratio as a reaction with hydrogen sulphide was suspected. Acetophenone emissions originated from the wood chips. Olfactory measurements need to be correlated to gaseous emissions for a more accurate odour emission evaluation.     

隔离曝气生物反应器处理含硫含酚碱渣

采用隔离曝气生物反应器（简称反应器）处理含硫含酚碱渣（简称碱渣）,探讨了碱渣中硫化物的去除机理．研究了反应器中的挂膜驯化过程,考察了水力停留时间、气水体积比（简称气水比）及反冲洗周期等对碱渣中硫化物、挥发酚、COD和油等污染物处理效果的影响。实验结果表明,在碱渣处理量为1m^3／h、气水比为36：1、水力停留时间为12．0h,反冲洗周期为3～5d的条件下,经过隔离曝气生物氧化工艺处理后碱渣的COD、硫化物、油和挥发酚的去除率分别为88％,99％,89％,85％,出水BOD,约为30mg／L,BOD,／COD小于0．1,处理1t碱渣的产泥量为0．17～0．26kg。     

ZFP-1380型曝气转盘充氧性能的测试和分析

介绍了ZFP-1380型曝气转盘的参数和性能,并对其在氧化沟污水处理工艺中的主要指标——充氧能力和动力效率的主要影响因素作了测试和分析。该转盘适宜的浸没深度为480～510mm、转速为52～56r/min,在此运转条件下,单片转盘的充氧能力为1.78～1.98kg/h,动力效率为3.18～3.43kg/(kW     

曝气-过滤一体化装置脱氮除磷的研究

曝气-过滤一体化装置将生物反应器与过滤机理有机结合,较好地维持了反应器中的高污泥浓度,实现了水力停留时间（HRT）与污泥停留时间的分离。采用连续流间歇曝气工艺对该装置的脱氮除磷效果进行了研究。实验结果表明：在HRT为8h,运行方式为曝气2h、停曝2h的条件下,COD去除率为95．55％,NH3-N未检出,TN为84．90％,TP为93．69％,出水各项指标都达到了GB8978-1996（污水综合排放标准》一级排放标准要求。     

循环经济的发展动力与前景

我国发展循环经济进入了由第十二个五年规划纲要统筹安排、全面发展的新阶段。总结了我国发展循环经济的主要做法和成功经验,深入分析循环经济发展的内在驱动力、面临的新形势,并提出切实推进循环经济健康快速发展的思路和重点,供循环经济领域的研究和管理者参考。     

湿法石灰石/石膏烟气脱硫泵的选材及选型

简述了湿法烟气脱硫生产中浆液的性质，并根据浆液特点阐述了耐磨耐蚀泵的选材与选型．为湿法石灰石／石膏烟气脱硫浆液输送泵的研发提供参考。     

再生资源行业存在的突出问题及对策探讨

在再生资源回收利用已成为大力推进生态文明建设重要内容的新形势下,着眼于这项工作更好地服务于经济与社会又好又快发展,提出行业目前存在的7个方面的突出问题和解决问题的10项对策,与相关部门和业内人士进行研讨.