低浓度CS2废气的光降解研究及工艺设计

利用185～253.7 nm紫外光联合降解低浓度二硫化碳废气.结果表明,在一定的气体浓度、流速以及湿度下,该技术能够有效降解二硫化碳使其浓度低于人的嗅阈值,同时研究也发现,该技术对苯乙烯和甲苯二甲苯等有机废气也有同样的处理效果,具有很好的工业化应用前景.     

气相色谱法测定空气和废气中的正己烷

建立了一种用气相色谱法测定空气和废气中正己烷的方法。空气和废气中正己烷用活性炭吸附，二硫化碳解吸，直接进样分析，其回收率为93．4％-101．3％，最低检出质量浓度为0．05mg／m^3，相对标准偏差为0．4％-2．1％；该方法前处理简单，速度快，干扰少，灵敏度高，可用于空气和废气中正己烷的测定。     

介质阻挡放电和水吸收联合降解挥发性有机化合物

依据介质阻挡放电(DBD)和溶液吸收处理气态污染物的原理,设计出一种DBD和水吸收联合降解挥发性有机化合物(VOCs)的实验装置.研究其对甲苯的降解效果.考察了放电电压、甲苯初始浓度、模拟废气流量对甲苯降解效果的影响.分析了DBD和水吸收的相互作用.结果表明.DBD和水吸收联合可以提高甲苯的降解率.在放电电压为15.9 kV时甲苯的降解率为81.5%.比单独放电时提高了13.3百分点;甲苯的降解率随着放电电压增大而升高,随着气体流量和甲苯初始浓度增大而降低.该技术可以作为放电等离子体前处理工艺,为高效处理上业废气提供参考.     

治理粘胶纤维生产废气的研究进展

粘胶纤维生产的废气含有二硫化碳和硫化氢 ,均为对人体有害、污染环境的气体。本文介绍了目前治理粘胶纤维生产废气的工艺方法。     

治理粘胶纤维生产废气的研究进展

粘胶纤维生产的废气含有二硫化碳和硫化氢,均为对人体有害,污染环境的气体,本文介绍了目前治理粘胶纤维生产废气的工艺方法.     

活性炭吸附-微波技术再生处理粘胶纤维废气的研究

针对粘胶纤维厂冷凝处理后的废气浓度低的特点,开发了吸附-微波再生处理技术。主要考察了吸附剂的种类、H2S和CS2进口浓度、湿度的影响,同时还对微波再生条件和效果进行了实验。结果表明,活性炭对二硫化碳的吸附效果较好;H2S和CS2进口浓度很低(Ci<200mg/m3)时对吸附影响不明显;湿度对吸附影响很大。实验亦证实,微波再生后的活性炭性能有很大的改善。     

活性炭吸附-微波技术再生处理粘胶纤维废气的研究

针对粘胶纤维厂冷凝处理后的废气浓度低的特点,开发了吸附-微波再生处理技术.主要考察了吸附剂的种类、H2S和CS2进口浓度、湿度的影响,同时还对微波再生条件和效果进行了实验.结果表明,活性炭对二硫化碳的吸附效果较好;H2S和CS2进口浓度很低（Ci＜200 mg/m^3）时对吸附影响不明显;湿度对吸附影响很大.实验亦证实,微波再生后的活性炭性能有很大的改善.     

电晕-介质阻挡协同放电低温等离子体降解大流量甲苯废气的研究

利用自制电晕-介质阻挡协同放电低温等离子体降解大流量甲苯废气,运用均匀设计法优化获得甲苯降解的适宜条件,探究了各因素及因素间交互作用对甲苯降解的影响,并开展甲苯降解动力学分析。结果表明:降解甲苯的最佳条件为工作电压13kV、放电频率6.5kHz、废气流量为1.0L/min,甲苯初始质量浓度924mg/m~3,在此条件下甲苯气体降解率为94.93%,能量效率为0.63g/(kW·h);甲苯降解符合一级反应动力学,甲苯降解反应速率常数与输入功率具有良好线性关系。     

生物法降解低浓度含甲苯废气的研究

筛选出以甲苯为唯一碳源的高效降解甲苯的假单孢菌Pseudmonas sp.ZD5，并设计生物滤池装置，研究了温度为10－50℃、相对湿度为50％－80％、人口甲苯浓度为1000－4500mg/m^3、气流量为0.3-0.7m^3/h的操作条件对甲苯降解率的影响，得出甲苯最高降解率为89.7%，表明此细菌降解低浓度甲苯废气有较好的效果。     

生物法净化再生胶生产废气工业试验研究

在再生橡胶厂进行橡胶再生低浓度有机废气的生物法净化工业试验研究，对于甲苯浓度为300～1400mg/m^3的再生胶脱硫废气，在常温常压下以气体流量10～20m^3/h、循环液体喷淋量300～500L/h运行生物法废气净化装置获得了良好物净化效果。该装置连续运行100d的结果显示，其对再生胶废气中甲苯的净化效率可较长时间的保持在90%左右，废气经处理后可以实现达标排放，废气处理成本约为工厂再生胶产值的0.12%～0.14%，具有明显的技术先进性和经济合理性。     

Measurement of biosolids compost odor emissions from a windrow, static pile, and biofilter.

A pilot study was conducted to compare odor emissions from a windrow process and an aerated static pile and to determine the odor reduction efficiency of a pilot two-phase biofilter for odor control of biosolids composting. Chemical compounds identified as responsible for odors from biosolids composting include ammonia, dimethyl disulfide, carbon disulfide, formic acid, acetic acid, and sulfur dioxide (or carbonyl sulfide). Aeration was found to reduce the concentration of ammonia, formic acid, and acetic acid by 72, 57, and 11%, respectively, compared with a nearby windrow, while dimethyl sulfide, carbon disulfide, and sulfur dioxide (or carbonyl sulfide) concentrations were below detection limits. Using dilution-to-threshold olfactometry, aeration followed by biofiltration was found to reduce the odor from biosolids composting by 98%. Biofiltration also altered the character of odor emissions from biosolids composting, producing a less offensive odor with an earthy character. Biofiltration was found to reduce the concentration of ammonia, dimethyl disulfide, carbon disulfide, formic acid, acetic acid, and sulfur dioxide (or carbonyl sulfide) by 99, 90, 32, 100, 34, and 100%, respectively. The concentrations of those odorants were estimated to be 3700, 110000, 26,37,5, and 1.2 times reported human detection limits before the two-phase biofilter, respectively, and 42,9600,18,0,3, and 0 times human detection limits after the biofilter, respectively.     

Sulfur Gas Emissions From Stored Flue Gas Desulfurization Sludges

The emissions of volatile sulfur-containing compounds from 13 flue gas desulfurization (FGD) sludge field storage sites have been characterized. Sulfur gas emissions from the sludge surfaces were determined by measuring the sulfur gas enhancement of sulfur-free sweep air passing through a dynamic emission flux chamber placed over selected sampling sites. Samples of the enclosure sweep air were cryogenically concentrated in surface-deactivated Pyrex “U” traps. Analyses were conducted by wall-coated, open-tubular, capillary column, cyrogenic gas chromatography using a sulfur-selective, flame photometric detector. Several major variables associated with FGD sludge production processes were examined in relation to the measured range and variations in sulfur fluxes including: (a) the sulfur dioxide scrubbing reagent used, (b) sludge sulfite oxidation, (c) “unfixed” or “fixed” FGD sludge, and (d) ponding or landfill storage. The composition and concentration of the measured sulfur gas emissions were found to vary with the type of sludge, the effectiveness of rainwater drainage from the landfill surface, the method of impoundment, and the sulfate/sulfite ratio of the sludge. Hydrogen sulfide, carbonyl sulfide, dimethyl sulfide, carbon disulfide, and dimethyl disulfide were identified in varying concentrations and ratios in the FGD sludge emissions. In addition, up to four unidentified organo- sulfur compounds were found in the emissions from four FGD sludges. The sulfur flux from one FGD storage pond was analyzed by gas chromatography-single ion monitoring mass spectrometry. In addition to the four identified sulfur compounds, this flux contained large concentrations of benzene, toluene, and α-pinene. The measured, total sulfur emissions ranged from less than 0.01 to nearly 0.3 kg of sulfur per day for an equivalent 100 acre (40.5 hectare) sludge impoundment surface.     

Sulfur Gas Emissions from Flue Gas Desulfurization Sludge Ponds

This paper presents initial measurement data on the emission of volatile, reduced sulfur-containing gases from flue gas desulfurization (FGD) storage ponds. Several different types of FGD stored sludges were studied including lime, limestone, and mixtures of fly ash and lime or limestone residues, some of which had been chemically stabilized. The volatile sulfur gas emissions were cryogenically concentrated and determined by wall-coated, open-tubular capillary column gas chromatography using a flame photometric detector. Hydrogen sulfide, carbonyl sulfide, dimethyl sulfide, carbon disulfide, and an unusual, unidentified sulfur-containing compound were found in the gaseous pond flux. Benzene, toluene, and α-pinene were also identified by gas chromatography-single ion monitoring mass spectrometry. The total reduced sulfur gas emission from a 100 acre pond approximated 2.0 kg day^?1 (as sulfur).     

A sorptive slurry bioscrubber for the control of acetone

A sorptive slurry bioscrubber adds powdered activated carbon (PAC) to a conventional suspended-growth bioscrubber. The activated carbon increases pollutant removal from the gas phase due to adsorption on carbon. The carbon is bioregenerated in the oxidation reactor and recycled to the scrubbing column. A three-stage, conventional bioscrubber was tested with and without carbon. The experiments showed that the PAC improved the removal efficiency of the system and that bioregeneration occurred. At an inlet gas-phase acetone concentration of 50 ppmv, the steady-state removal increased from 88 to 95% when activated carbon was added to the biological slurry.     

Wind tunnel study of air entrainment into two-dimensional dense gas plumes at the Chemical Hazards Research Center

Experiments in a neutrally stable wind tunnel boundary layer were made for two-dimensional (quasi-line) sources of carbon dioxide dispersing over two types of uniformly spaced (billboard) surface roughness elements. Velocity and concentration measurements were made with each surface roughness over a wide range of source Richardson number by varying carbon dioxide release rate and wind speed. Concentration measurements were made with a FID gas analyzer using an ethane tracer in the source gas, and velocity measurements were made with independent LDV and HWA systems. For each surface roughness, this paper describes the wind tunnel boundary layer and presents alongwind and vertical concentration profiles in the gas plume. Vertical velocity and concentration profiles were measured at selected downwind distances, and the profiles were integrated to confirm the consistency of the measurements with the mass of carbon dioxide released. The data are intended for development of improved vertical turbulent entrainment correlations for use in dense gas dispersion models applied to hazardous chemical consequence analyses.     

Health risk assessment of odors emitted from urban wastewater pump stations in Tianjin,China

In order to evaluate the potential adverse health effects of odor emissions from wastewater pump stations (WWPSs) to human, a health risk assessment was performed to study the odors emitted from an urban WWPS in a residential area, Tianjin (in North China). First, 15 types of volatile organic compounds in the WWPS were collected and analyzed using gas chromatography-mass spectrometry. Next, Monte Carlo probabilistic modeling was applied to evaluate the potential health effects of four odors (chlorobenzene, dichloromethane, hydrogen sulfide, and carbon disulfide), which had higher concentrations. The results revealed that the 95th percentile of the total non-carcinogenic risk was approximately 1.73, which poses a threat to human health. In addition, hydrogen sulfide had the highest non-carcinogenic risk value of the four; the hazard quotient of hydrogen sulfide was estimated to be 1.60 at the 95th percentile, higher than the upper confidence limit (1.0). The 95th percentile of the carcinogenic risk was approximately 5.47E-08, much lower than the maximum acceptable level (1.0E-06). Finally, the influence of the input variables on the output was evaluated using sensitivity analysis, and contaminant concentration, reference concentration, and inhalation unit risk were the most influential variables.     

吸附法净化低浓度废气实验研究

本文探讨了用活性炭吸附低浓度苯类废气时,空塔气速和气流在吸附层的接触时间对吸附过程的影响;研究了活性炭在已经吸附若干质量的苯类物质以后的吸附性能.据此绘制了空塔气建-吸附效率和活性炭含苯率-吸附效率等关系曲线,并进行了活性炭再生的研究.研究表明:使用活性炭可以有效地净化低浓度苯类废气.     

Odorous volatile organic sulfides in wastewater treatment plants in Guangzhou, China

Odorous volatile organic sulfides (VOSs) in headspace atmosphere and wastewaters were identified and quantified synchronously in two municipal wastewater treatment plants (WWTPs) in Guangzhou, China. Dimethyl sulfide (DMS), with concentrations ranging from 0.66 to 5.41 mg/m3, was the major VOS in air samples. Carbonyl sulfide (COS), carbon disulfide (CS2), and dimethyl disulfide (DMDS) ranged from 0.01 to 0.21, 0.03 to 0.44, and 0.06 to 1.61 mg/m3, respectively. Methanethiol was not found in any gas samples. The concentrations of DMS in wastewaters ranged from 23.68 to 308.17 mg/m3 and were also the highest values compared with other VOSs, for all of the treatment processes. Methanethiol was detected in all wastewater samples, except that from the aeration tank, which ranged from 113.08 to 216.82 mg/m3. The COS, carbon disulfide, and DMDS in wastewaters ranged from 0.11 to 2.21, 1.37 to 23.29, and 0.24 to 106.75 mg/m3, respectively. Odors from pollution related to VOS were different in the two plants, and they were strongly associated with the characteristics of incoming wastewater and treatment processes. The VOSs in ambient air samples from nearby residential areas downwind of the plant border were also measured, and the results strongly suggested that control measures are needed for odor pollution in the WWTPs to mitigate malodor in the surrounding neighborhoods.     

钙基吸附剂捕集生物质燃气中的二氧化碳

生物质热解燃气中CO2的捕集,是提高燃气热值和实现碳减排的关键问题之一。为利用生物质热解燃气温度偏高的特点,拟通过化学吸附方法,捕集燃气中高浓度的CO2。为此,利用不同钙基前驱物制备了系列钙基固体吸附剂,系列钙基固体吸附剂对CO2的单次吸附和循环吸附实验结果表明,含钙和镁氧化物混合物的吸附剂具有较稳定的循环吸附特性以及较大的吸附负荷。孔结构特性分析表明,适宜于CO2吸附的有效孔径范围可能为小于4 nm。因此,可以通过对天然白云石的改性获得合适孔径的钙镁基固体吸附剂,达到有效捕集生物质燃气中CO2的目的。