A study on variations of concentrations of particulate matter with different sizes in Lanzhou,China

Lanzhou is one of the most air-polluted cities in China and in the world, and its primary air pollutant is particulate matter (PM). Different size particulate matter (TSP, PM₁₀, PM_2.5 and PM_1.0) have different sources and affect the environment and human health differently, so it is very important to study the pollutant characteristics of different particles in order to deeply understand the pollution situation of Lanzhou city and establish reasonable preventive countermeasures. TSP, PM₁₀, PM_2.5 and PM_1.0 concentrations were simultaneously measured in Lanzhou to detect the annual and diurnal variations of concentrations of PM with different sizes and possible causes. The main results are as follows: (1) The annual distribution of monthly average concentrations for coarse particles (TSP and PM₁₀) is bimodal with the highest peak in April, which is different from the situation in other cities not affected by sand-dust events. However, the annual distribution for fine particles (PM_2.5 and PM_1.0) is unimodal with the peak in December. This difference between coarse and fine particles indicates that sand-dust events in spring carry much more coarse than fine particles to Lanzhou. This result is supported by the correlation between springtime wind speed and concentrations of PM with different sizes. (2) Under normal conditions (without dust intrusions), the diurnal distribution of coarse particle concentration in Lanzhou is bimodal. However, the distribution is trimodal during dust intrusions in April, with an extra peak in the afternoon. (3) In general, the highest concentration peaks of the diurnal variations for TSP, PM₁₀, PM_2.5 and PM_1.0 occur at about the same time. However, there are obvious differences in the occurrence time of the minimum concentrations among different kinds of PM. The differences in the occurrence time of minima between coarse and fine particles are due to their different diffusion behaviors in the atmospheric boundary layer.     

Long-term variation of PM2.5 levels and composition at rural, urban, and roadside sites in Hong Kong: Increasing impact of regional air pollution

Long-term study of air pollution plays a decisive role in formulating and refining pollution control strategies. In this study, two 12-month measurements of PM_2.5 mass and speciation were conducted in 00/01 and 04/05 to determine long-term trend and spatial variations of PM_2.5 mass and chemical composition in Hong Kong. This study covered three sites with different land-use characteristics, namely roadside, urban, and rural environments. The highest annual average PM_2.5 concentration was observed at the roadside site (58.0±2.0 μg m⁻³ (average±2σ) in 00/01 and 53.0±2.7 μg m⁻³ in 04/05), followed by the urban site (33.9±2.5 μg m⁻³ in 00/01 and 39.0±2.0 μg m⁻³ in 04/05), and the rural site (23.7±1.9 μg m⁻³ in 00/01 and 28.4±2.4 μg m⁻³ in 04/05). The lowest PM_2.5 level measured at the rural site was still higher than the United States’ annual average National Ambient Air Quality Standard of 15 μg m⁻³. As expected, seasonal variations of PM_2.5 mass concentration at the three sites were similar: higher in autumn/winter and lower in summer. Comparing PM_2.5 data in 04/05 with those collected in 00/01, a reduction in PM_2.5 mass concentration at the roadside (8.7%) but an increase at the urban (15%) and rural (20%) sites were observed. The reduction of PM_2.5 at the roadside was attributed to the decrease of carbonaceous aerosols (organic carbon and elemental carbon) (>30%), indicating the effective control of motor vehicle emissions over the period. On the other hand, the sulfate concentration at the three sites was consistent regardless of different land-use characteristics in both studies. The lack of spatial variation of sulfate concentrations in PM_2.5 implied its origin of regional contribution. Moreover, over 36% growth in sulfate concentration was found from 00/01 to 04/05, suggesting a significant increase in regional sulfate pollution over the years. More quantitative techniques such as receptor models and chemical transport models are required to assess the temporal variations of source contributions to ambient PM_2.5 mass and chemical speciation in Hong Kong.     

Determination and analysis of PM10 source apportionment during episodes of air pollution in Central Eastern European urban areas: The case of wintertime 2006

Source apportionment of air pollution due to particulate matter with an aerodynamic diameter <10 μm (PM₁₀) was investigated in Central Eastern European urban areas. A combination of four methods was developed to distinguish long-range transport (LRT) and regional transport (RT) from local pollution (LP) sources as well as to discern the involvement of traffic or residential sources in LP. Sources of PM₁₀ events of pollution were determined in January 2006 in representative Polish cities using monitored air quality and meteorological data, backward air mass trajectories, correlation and principal component analysis (PCA). Daily patterns of PM₁₀ levels show that several peak episodes were registered in Poland; January 21–30th being the most polluted days. Air mass back-trajectory analysis shows that all cities were under the influence of LRT from North-eastern origins (Russia–Belarus–Ukraine), most were also under LRT from Southern origin (Slovakia, Czech Republic), and northern cities were under national RT influence. PCA analysis shows that ion-sums of secondary inorganic aerosols account for LRT pollution while arsenic and chromium represents markers of RT (industrial) and LP (residential) sources of PM₁₀, respectively. Determination of several ratios (REG/UB, REG/TRAF, TRAF/UB) calculated between PM₁₀ levels measured at regional background (REG); urban background (UB) and traffic (TRAF) monitoring sites shows that, with ratios REG/UB ≥ 0.57, PM₁₀ episodes in both Szczecin and Warsaw bore a marked RT origin. The lower REG/UB ≤ 0.35 in the Southern cities of Cracow and Zabrze indicates that LP was the main contributor to the observed episodes. Only PM₁₀ episodes in Southern-western Poland (Jelenia Góra) were clearly of LP origin as characterized, by the lowest REG/UB ratio (<0.2). The high TRAF/UB ratios obtained for all cities (close to 1) indicate that there was a great uniformity of PM levels on an urban scale owing to the meteorologically stagnant conditions. A high correlation between PM₁₀, NO₂ and CO confirms that traffic emission represented a common and an important LP source of urban pollution in most Polish cities during January 2006. On the other hand PM₁₀ which is also highly correlated with SO₂ in 4 cities out of 6, indicates that coal combustion through domestic heating or industrial activities was also an important LP source of PM₁₀. Finally, extremely unfavourable meteorological conditions caused by the influence of a Siberian high-pressure system were found to be associated with the occurrence of severe PM₁₀ episodes of pollution.     

Influence of particulate matter on the air quality situation in a mediterranean island

The objective of this study was to describe the ambient levels of particulate matter (PM) and its influence to air quality situation on the dry Mediterranean island of Cyprus. From October 2002 to August 2003 PM₁₀ and PM_2.5 samples were collected at 31 different sampling sites in Cyprus. In addition, continuous measurements of PM₁₀ were carried out from 2003 to 2007 at a traffic and a rural site. It can be recognised that at all traffic and at some residential and urban background sites, the actual EU limit values have been exceeded. Special events e.g. long-range transport of Sahara dust storms were recorded over urban as well as rural areas in the order of 6–8 events per year, with a major frequency in summer and spring periods. The comparison of the PM₁₀ concentrations in Cyprus cities with values of other European cities demonstrates the PM₁₀ problem in Cyprus, especially in the dry summer season, when no rain is cleaning the air and the dry surfaces. This underlines the necessity of PM abatement strategies.     

Windblown Dust Contributes to High PM25 Concentrations

ABSTRACT

The revised National Ambient Air Quality Standards for PM include fine particulate standards based upon mass measurements of PM₂₅. It is possible in arid and semi-arid regions to observe significant coarse mode intrusion in the PM_2.5 measurement. In this work, continuous PM₁₀, PM_2.5, and PM_1.0 were measured during several windblown dust events in Spokane, WA. PM_{2 5} constituted ~30% of the PM₁₀ during the dust event days, compared with ~48% on the non-dusty days preceding the dust events. Both PM₁₀ and PM_2.5 were enhanced during the dust events. However, PM_1.0 was not enhanced during dust storms that originated within the state of Washington. During a dust storm that originated in Asia and impacted Spokane, PM_1.0 was also enhanced, although the Asian dust reached Washington during a period of stagnation and poor dispersion, so that local sources were also contributing to high particulate levels. The “intermodal” region of PM, defined as particles ranging in aerodynamic size from 1.0 to 2.5 um, was found to represent a significant fraction of PM₂₅ (~51%) during windblown dust events, compared with 28% during the non-dusty days before the dust events.     

Assessment of natural components of PM10 at UK urban and rural sites

Proposals from the European Commission have raised the possibility that Member States may be able to subtract the concentrations of natural components of airborne particulate matter from measured concentrations when evaluating compliance with EU Limit Values. By applying the pragmatic mass closure model [Harrison et al., 2003. A pragmatic mass closure model for airborne particulate matter at urban background and roadside sites. Atmospheric Environment 37, 4927–4933] to chemical composition data for PM₁₀, it has been possible to estimate the concentrations of natural sea salt, strongly bound water and secondary organic carbon (which is assumed wholly biogenic) to the measured mass of PM₁₀. Because of the difficulty in distinguishing between natural and anthropogenic crustal dusts, the contribution of natural windblown dust and soil has not been accounted for. When the natural components are estimated for two urban and one rural site in the UK, the long-term mean PM₁₀ concentration is reduced by between 5.2 and 7.3 μg m⁻³. The number of exceedences of the 50 μg m⁻³ 24-h limit value falls dramatically from 54 to 21 (from a total of 291 days) at an urban street canyon site, 7 to 3 (n=292 days) at an urban background site and from 8 to 0 (n=241 days) at a rural site when using gravimetric PM₁₀ concentrations. The calculations have also been performed using PM₁₀ concentrations measured by TEOM increased by a factor of 1.3 as recommended by the European Commission as an interim means of estimating gravimetric equivalency, and the number of exceedences of the 24-h limit value fell from 92 to 47 (from a total of 291 days) at the urban street canyon site, from 11 to 3 (n=292 days) at the urban background site and from 6 to 3 (n=241) at the rural site. Clearly, therefore, application of this proposed measure would make a very major difference to the likelihood of compliance or otherwise with the 24-h limit value for PM₁₀.     

Source Apportionment of Particulate Matter (PM10) and Indoor Dust in a University Building

A study on source apportionment of indoor dust and particulate matter (PM₁₀) composition was conducted in a university building by using chemometrics. The objective of this study was to investigate the potential sources of selected heavy metals and ionic species in PM₁₀ and indoor dust. PM₁₀ samples were collected using a low-volume sampler (LVS) and indoor dust was collected using a soft brush. Inductively coupled plasma spectrometry (ICP-MS) was used to determine the concentration of heavy metals, while the concentration of cations and anions was determined by atomic absorption spectrometer (AAS) and ion chromatography (IC), respectively. The concentration of PM₁₀ recorded in the building throughout the sampling period ranged from 20 ± 10 μgm^?3 to 80 ± 33 μgm^?3. The composition of heavy metals in PM₁₀ and indoor dust were dominated by zinc (Zn), followed by lead (Pb), copper (Cu), and cadmium (Cd). Principle component analysis (PCA) and multiple linear regression (MLR) showed that the main sources of pollutants in PM₁₀ came from indoor renovations (73.83%), vehicle emissions (16.38%), earth crust sources (9.68%), and other outdoor sources (0.11%). For indoor dust, the pollutant source was mainly earth crust. This study suggests that chemometrics can be used for forensic investigation to determine the possible sources of indoor contaminants within a public building.     

Association between particulate matter air pollution and cardiovascular disease mortality in Lanzhou,China

Ambient particulate matter (PM) pollution has been linked to elevated mortality, especially from cardiovascular diseases. However, evidence on the effects of particulate matter pollution on cardiovascular mortality is still limited in Lanzhou, China. This research aimed to examine the associations of daily mean concentrations of ambient air pollutants (PM_2.5, PM_C, and PM₁₀) and cardiovascular mortality due to overall and cause-specific diseases in Lanzhou. Data representing daily cardiovascular mortality rates, meteorological factors (daily average temperature, daily average humidity, and atmospheric pressure), and air pollutants (PM_2.5, PM₁₀, SO₂, NO₂) were collected from January 1, 2014, to December 31, 2017, in Lanzhou. A quasi-Poisson regression model combined with a distributed lag non-linear model (DLNM) was used to estimate the associations. Stratified analyses were also performed by different cause-specific diseases, including cerebrovascular disease (CD), ischemic heart disease (IHD), heart rhythm disturbances (HRD), and heart failure (HF). The results showed that elevated concentration of PM_2.5, PM_C, and PM₁₀ had different effects on mortality of different cardiovascular diseases. Only cerebrovascular disease showed a significant positive association with elevated PM_2.5. Positive associations were identified between PM_C and daily mortality rates from total cardiovascular diseases, cerebrovascular diseases, and ischemic heart diseases. Besides, increased concentration of PM₁₀ was correlated with increased death of cerebrovascular diseases and ischemic heart diseases. For cerebrovascular disease, each 10 μg/m³ increase in PM_2.5 at lag4 was associated with increments of 1.22% (95% CI 0.11–2.35%). The largest significant effects for PM_C on cardiovascular diseases and ischemic heart diseases were both observed at lag0, and a 10 μg/m³ increment in concentration of PM_C was associated with 0.47% (95% CI 0.06–0.88%) and 0.85% (95% CI 0.18–1.52%) increases in cardiovascular mortality and ischemic heart diseases. In addition, it exhibited a lag effect on cerebrovascular mortality as well, which was most significant at lag6d, and an increase of 10 μg/m³ in PM_C was associated with a 0.76% (95% CI 0.16–1.37%) increase in cerebrovascular mortality. The estimates of percentage change in daily mortality rates per 10 μg/m³ increase in PM₁₀ were 0.52% (95% CI 0.05–1.02%) for cerebrovascular disease at lag6 and 0.53% (95% CI 0.01–1.05%) for ischemic heart disease at lag0, respectively. Our study suggests that elevated concentration of atmospheric PM (PM_2.5, PM_C, and PM₁₀) in Lanzhou is associated with increased mortality of cardiovascular diseases and that the health effect of elevated concentration of PM_2.5 is more significant than that of PM_C and PM₁₀.

     

Physicochemical variations in atmospheric aerosols recorded at sea onboard the Atlantic–Mediterranean 2008 Scholar Ship cruise (Part I): Particle mass concentrations,size ratios,and main chemical components

We report on ambient atmospheric aerosols present at sea during the Atlantic–Mediterranean voyage of Oceanic II (The Scholar Ship) in spring 2008. A record was obtained of hourly PM₁₀, PM_2.5, and PM₁ particle size fraction concentrations and 24-h filter samples for chemical analysis which allowed for comparison between levels of crustal particles, sea spray, total carbon, and secondary inorganic aerosols. On-board monitoring was continuous from the equatorial Atlantic to the Straits of Gibraltar, across the Mediterranean to Istanbul, and back via Lisbon to the English Channel. Initially clean air in the open Atlantic registered PM₁₀ levels <10 μg m^?3 but became progressively polluted by increasingly coarse PM as the ship approached land. Away from major port cities, the main sources of atmospheric contamination identified were dust intrusions from North Africa (NAF), smoke plumes from biomass burning in sub-Saharan Africa and Russia, industrial sulphate clouds and other regional pollution sources transported from Europe, sea spray during rough seas, and plumes emanating from islands. Under dry NAF intrusions PM₁₀ daily mean levels averaged 40–60 μg m^?3 (30–40 μg m^?3 PM_2.5; c. 20 μg m^?3 PM₁), peaking briefly to >120 μg m^?3 (hourly mean) when the ship passed through curtains of higher dust concentrations amassed at the frontal edge of the dust cloud. PM₁/PM₁₀ ratios ranged from very low during desert dust intrusions (0.3–0.4) to very high during anthropogenic pollution plume events (0.8–1).     

Results from a pilot-scale air quality study in Addis Ababa, Ethiopia

Twenty-one samples were collected during the dry season (26 January–28 February 2004) at 12 sites in and around Addis Ababa, Ethiopia and analyzed for particulate matter with aerodynamic diameter <10 μm (PM₁₀) mass and composition. Teflon-membrane filters were analyzed for PM₁₀ mass and concentrations of 40 elements. Quartz-fiber filters were analyzed for chloride, sulfate, nitrate, and ammonium ions as well as elemental carbon (EC) and organic carbon (OC) content. Measured 24-h PM₁₀ mass concentrations were <100 and 40 μg m⁻³ at urban and suburban sites, respectively. PM₁₀ lead concentrations were <0.1 μg m⁻³ for all samples collected, an important finding because the government of Ethiopia had stopped the distribution of leaded gasoline a few months prior to this study. Mass concentrations reconstructed from chemical composition indicated that 34–66% of the PM₁₀ mass was due to geologically derived material, probably owing to the widespread presence of unpaved roads and road shoulders. At urban sites, EC and OC compounds contributed between 31% and 60% of the measured PM₁₀ while at suburban sites carbon compounds contributed between 24% and 26%. Secondary sulfate aerosols were responsible for <10% of the reconstructed mass in urban areas but as much as 15% in suburban sites, where PM₁₀ mass concentrations were lower. Non-volatile particulate nitrate, a lower limit for atmospheric nitrate, constituted <5% and 7% of PM₁₀ at the urban and suburban sites, respectively. At seven of the 12 sites, real-time PM₁₀ mass, real-time carbon monoxide (CO), and instantaneous ozone (O₃) concentrations were measured with portable nephelometers, electrochemical analyzers, and indicator test sticks, respectively. Both PM₁₀ and CO concentrations exhibited daily maxima around 7:00 and secondary peaks in the late afternoon and evening, suggesting that those pollutants were emitted during periods associated with motor-vehicle traffic, food preparation, and heating of homes. The morning concentration maxima were likely accentuated by stable atmospheric conditions associated with overnight surface temperature inversions. Ozone concentrations were measured near mid-day on filter sample collection days and were in all cases <45 parts per billion.     

Using Si depletion in aerosol to identify the sources of crustal dust in two Chinese megacities

Depletion of Si in transported dust has been recognized for many years. It can be used to distinguish between transported and local dust in cities, although it rarely has been. Here we use the variations of the Si/Al ratio in 15 months of continuous PM_2.5 samples at Beijing (northern China) and Chongqing (southwestern China) to reveal the seasonal patterns of their dust sources. For both cities, peaks of concentration for Si and Al in PM_2.5 corresponded with minima of Si/Al, and could often be linked to pulsed air flow from deserts to the northwest. With significant depletion (up to 80%) and homogeneous distribution at urban and rural sites, Si/Al showed a clear seasonal evolution, which decreased from spring to summer, increased from fall to winter, and collapsed during Chinese Spring Festival, indicating the dominance of transported dust, local fugitive dust and firework influence, respectively. The low ratios implied that desert dust is a common source during spring at Chongqing, whereas its presence during cold season at Beijing was also more frequent than expected. Failing to recognize the depletion of Si may lead to an overestimate of desert dust by 15%–65% when using the average abundance of Al in crust (6%–8%), as in previous studies. The difference in Si/Al ratio between local and transported dust implies that >60% of the dust at Beijing came from outside the city during the springs of 2004–2006. This result can help resolve the contradictory findings on this topic that have been presented earlier.     

Monitoring of dust emission on gravel roads: Development of a mobile methodology and examination of horizontal diffusion

Traffic-generated fugitive dust on gravel roads impairs visibility and deposits on the adjacent environment. Particulate matter smaller than 10 μm in diameter (PM₁₀) is also associated with human health problems. Dust emission strength depends on the composition of granular material, road moisture, relative humidity, local climate (precipitation, wind velocity, etc.), and vehicle characteristics.The objectives of this study were to develop a reliable and rapid mobile methodology to measure dust concentrations on gravel roads, evaluate the precision and repeatability of the methodology and correspondence with the currently used visual assessment technique. Downwind horizontal diffusion was studied to evaluate the risk of exceeding the maximum allowed particulate matter concentration in ambient air near gravel roads according to European Council Directive [European Council Directive 1999/30/EC of 22 April 1999 relating to limit values for sulphur dioxide, nitrogen dioxide and oxides of nitrogen, particulate matter and lead in ambient air. Official Journal of the European Communities. L163/41.].A TSI DustTrak Aerosol Monitor was mounted on an estate car travelling along test sections treated with various dust suppressants. Measured PM₁₀ concentrations were compared to visual assessments performed at the same time. Airborne particles were collected in filters mounted behind the vehicle to compare the whole dust fraction with the PM₁₀ concentration. For measuring the horizontal diffusion, DustTraks were placed at various distances downwind of a dusty road section.The mobile methodology was vehicle and speed dependent but not driver dependent with pre-specified driving behaviours. A high linear correlation between PM₁₀ of different vehicles makes relative measurements of dust concentrations possible. The methodology gives continuous data series, mobility, and easy handling and provides fast, reliable and inexpensive measurements for estimating road conditions to make road maintenance more efficient.Good correlations between measured PM₁₀-values, visually assessed dust generation and dust collected in filters were obtained. PM₁₀ seems to be correlated to the whole dust fraction that impairs visibility on gravel roads.A decay in PM₁₀ concentration as a function of distance from the road was observed. Measured particles principally did not travel further than 45 m from the road. The risk of exceeding the PM₁₀ concentration stated in the EC-directive seems small.     

Implementation of a windblown dust parameterization into MODELS-3/CMAQ: Application to episodic PM events in the US/Mexico border

Windblown dust is known to impede visibility, deteriorate air quality and modify the radiation budget. Arid and semiarid areas with unpaved and unvegetated land cover are particularly prone to windblown dust, which is often attributed to high particulate matter (PM) pollution in such areas. Yet, windblown dust is poorly represented in existing regulatory air quality models. In a study by the authors on modeling episodic high PM events along the US/Mexico border using the state-of-the-art CMAQ/MM5/SMOKE air quality modeling system [Choi, Y.-J., Hyde, P., Fernando, H.J.S., 2006. Modeling of episodic particulate matter events using a 3D air quality model with fine grid: applications to a pair of cities in the US/Mexico border. Atmospheric Environment 40, 5181–5201], some of the observed PM₁₀ NAAQS exceedances were inferred as due to windblown dust, but the modeling system was incapable of dealing with time-dependent episodic dust entrainment during high wind periods. In this paper, a time-dependent entrainment parameterization for windblown dust is implemented in the CMAQ/MM5/SMOKE modeling system with the hope of improving PM predictions. An approach for realizing windblown dust emission flux for each grid cell over the study domain on an hourly basis, which accounts for the influence of factors such as soil moisture content, atmospheric stability and wind speed, is presented in detail. Comparison of model predictions with observational data taken at a pair of US/Mexico border towns shows a clear improvement of model performance upon implementation of the dust emission flux parameterization.     

African dust contributions to mean ambient PM10 mass-levels across the Mediterranean Basin

Data on mass-levels of PM₁₀ measured at regional background sites across the Mediterranean Basin, available from Airbase (European Environmental Agency) and from a few aerosol research sites, are compiled. PM₁₀ levels increase from north to south and west to east of the Basin. These variations are roughly coincident with the PM₁₀ African mineral dust load. However, when subtracting the African dust from mean PM₁₀ levels using a consistent methodology, the PM₁₀ background levels are still 5–10 μg m^?3 higher in the Eastern Basin (EMB) when compared with those in the Western (WMB), mainly due to the higher anthropogenic and sea spray loads.As regards for the seasonal trends, these are largely driven by the occurrence of African dust events, resulting in a spring-early summer maximum over the EMB, and a clear summer maximum in the WMB, although in this later region the recirculations of aged air masses play an important role. Furthermore, a marked seasonal trend is still evident when subtracting the African dust load. This is characterised by a high summer maximum (driven by low precipitation, high insolation) and a winter minimum (intense synoptic winds).Important inter-annual variations in the dust contribution are detected, more evident in the southern sites. These differences are generally associated with the occurrence of extreme dust events. Generally, the years with higher dust contributions over the EMB correspond with lower contributions over the WMB, and vice versa.The characterization of individual particles, collected in both basins during African dust events, by scanning electron microscopy reveals only slight differences between them. This fact probably reflects the high degree of mixture of mineral dust from different sources before the transport towards the receptor sites.     

Polychlorinated dibenzo-p-dioxin and dibenzofuran in urban air of an Andean city

Particle-bound polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/Fs) in ambient air were monitored together with particulate matter less than 10 μm (PM₁₀) at three sampling sites of the Andean city of Manizales, Colombia; during September 2009 and July 2010. PCDD/Fs ambient air emissions ranged from 1 fg WHO-TEQ m⁻³ to 52 fg WHO-TEQ m⁻³ in particulate fraction. The PM₁₀ concentrations ranged from 23 μg m⁻³ to 54 μg m⁻³. Concentrations of PM₁₀ and PCDD/Fs in ambient air observed for Manizales - a medium sized city with a population of 380 000 - were comparable to concentrations in larger cities. The highest concentrations of PCDD/Fs and PM₁₀ found in this study were determined at the central zone of the city, characterized by public transportation density, where diesel as principal fuel is used. In addition, hypothetical gas fractions of PCDD/Fs were calculated from theoretical K_p data. Congener profiles of PCDD/Fs exhibited ratios associated with different combustion sources at the different sampling locations, ranging from steel recycling to gasoline and diesel engines. Taking into account particle and gas hypothetical fraction of PCDD/Fs, Manizales exhibited values of PCDD/Fs equivalent to rural and urban-industrial sites in the southeast and center of the city respectively. Poor correlation of PCDDs with PM₁₀ (r = −0.55 and r = 0.52) suggests ambient air PCDDs were derived from various combustion sources. Stronger correlation was observed of PCDFs with PM₁₀. Poor correlation between precipitation and reduced PM₁₀ concentration in ambient air (r = −0.45) suggested low PM₁₀ removal by rainfall.     

Estimating fugitive dust emission rates using an environmental boundary layer wind tunnel

Emissions from fugitive dust due to erosion of “natural” wind-blown surfaces are an increasingly important part of PM₁₀ (particulate matter with sizes of 10 μm aerodynamic diameter) emission inventories. These inventories are particularly important to State Implementation Plans (SIP), the plan required for each state to file with the Federal government indicating how they will comply with the Federal Clean Air Act (FCAA). However, techniques for determining the fugitive dust contribution to over all PM₁₀ emissions are still in their developmental stages. In the past, the methods have included field monitoring stations, specialized field studies and field wind-tunnel studies. The measurements made in this paper allow for systematic determination of PM₁₀ emission rates through the use of an environmental boundary layer wind tunnel in the laboratory. Near surface steady-state concentration profiles and velocity profiles are obtained in order to use a control volume approach to estimate emission rates. This methodology is applied to soils retrieved from the nation's single largest PM₁₀ source, Owens (dry) Lake in California, to estimate emission rates during active storm periods. The estimated emission rates are comparable to those obtained from field studies and lend to the validity of this method for determining fugitive dust emission rates.     

Traffic generated non-exhaust particulate emissions from concrete pavement: A mass and particle size study for two-wheelers and small cars

This study aimed to understand the non-exhaust (NE) emission of particles from wear of summer tire and concrete pavement, especially for two wheelers and small cars. A fully enclosed laboratory-scale model was fabricated to simulate road tire interaction with a facility to collect particles in different sizes. A road was cast using the M-45 concrete mixture and the centrifugal casting method. It was observed that emission of large particle non exhaust emission (LPNE) as well as PM₁₀ and PM_2.5 increased with increasing load. The LPNE was 3.5 mg tire⁻¹ km⁻¹ for a two wheeler and 6.4 mg tire⁻¹ km⁻¹ for a small car. The LPNE can lead to water pollution through water run-off from the roads. The contribution of the PM₁₀ and PM_2.5 was smaller compared to the LPNE particles (less than 0.1%). About 32 percent of particle mass of PM₁₀ was present below 1 μm. The number as well as mass size distribution for PM₁₀ was observed to be bi-modal with peaks at 0.3 μm and 4–5 μm. The NE emissions did not show any significant trend with change in tire pressure.     

Assessment of traffic-related air pollution in the urban streets before and during the 2008 Beijing Olympic Games traffic control period

In order to investigate the air quality and the abatement of traffic-related pollution during the 2008 Olympic Games, we select 12 avenues in the urban area of Beijing to calculate the concentrations of PM₁₀, CO, NO₂ and O₃ before and during the Olympic traffic controlling days, with the OSPM model.Through comparing the modeled results with the measurement results on a representative street, the OSPM model is validated as sufficient to predict the average concentrations of these pollutants at street level, and also reflects their daily variations well, i.e. CO presents the similar double peaks as the traffic flow, PM₁₀ concentration is influenced by other sources. Meanwhile, the model predicts O₃ to stay less during the daytime and ascend in the night, just opposite to NO₂, which reveals the impact of photochemical reactions. In addition, the predicted concentrations on the windward side often exceed the leeward side, indicating the impact of the special street shape, as well as the wind.The comparison between the predicted street concentrations before and during the Olympic traffic control period shows that the overall on-road air quality was improved effectively, due to the 32.3% traffic flow reduction. The concentrations of PM₁₀, CO and NO₂ have reduced from 142.6 μg m⁻³, 3.02 mg m⁻³ and 118.7 μg m⁻³ to 102.0 μg m⁻³, 2.43 mg m⁻³ and 104.1 μg m⁻³. However, the different pollutants show diverse changes after the traffic control. PM₁₀ decreases most, and the reduction effect focusing on the first half-day even clears the morning peak, whereas CO and NO₂ have even reductions to minify the daily fluctuations on the whole. Opposite to the other pollutants, ozone shows an increase of concentration. The average reduction rate of PM₁₀, CO, NO₂ and O₃ are respectively 28%, 19.3%, 12.3% and −25.2%. Furthermore, the streets in east, west, south and north areas present different air quality improvements, probably induced by the varied background pollution in different regions around Beijing, along with the impact of wind force. This finding suggests the pollution control in the surrounding regions, not only in the urban area.     

Source apportionment of PM10 in six cities of northern China

Ambient PM₁₀ was sampled in six northern China cities (Urumqi, Yinchuan, Taiyuan, Anyang, Tianjin and Jinan) from December 1999 to July 2002, and analyzed for 16 chemical elements, two water-soluble ions, total carbon, and organic carbon. In addition, chemical source profiles consisting of the same particulate components were obtained from a number of naturally occurring geological sources (soil dust from exposed lands) and sources of atmospheric particulates resulting from human activities (resuspended dust, cement, coal combustion fly ash, vehicle exhaust, and secondary particles). Ambient and source data were used in a chemical mass balance (CMB) receptor model to determine the major source of PM₁₀ in these six cities. Results of CMB modeling showed that the major source of ambient PM₁₀ in all the cities was resuspended dust. Significant contributions from coal fly ash were also found in all six cities.     

Quantification of Saharan dust contribution to PM10 concentrations over Italy during 2003–2005

Italy is frequently affected by Saharan dust intrusions, which result in high PM₁₀ concentrations in the atmosphere and can cause the exceedances of the PM₁₀ daily limits (50 μg m^?3) set by the European Union (EU/2008/50). The estimate of African dust contribution to PM₁₀ concentrations is therefore a key issue in air quality assessment and policy formulation. This study presents a first identification of Saharan dust outbreaks as well as an estimate of the African dust contribution to PM₁₀ concentrations during the period 2003–2005 over Italy. The identification of dust events has been carried out by looking at different sources of information such as monitoring network observations, satellite images, ground measurements of aerosol optical properties, dust model simulations and air mass backward trajectory analysis. The contribution of Saharan dust to PM₁₀ monthly concentrations has been estimated at seven Italian locations. The results are both spatially (with station) and temporally (with month and year) variable, as a consequence of the variability of the meteorological conditions. However, excluding the contribution of severe dust events (21st February 2004, 25th–28th September 2003, 23rd–27th March 2005), the monthly contribution of dust varies approximately between 1 μg m^?3 and 10 μg m^?3 throughout year 2005 and between 1 μg m^?3 and 8 μg m^?3 throughout year 2003. In 2004 the dust concentration is lower than 2003 and 2005 (<5 μg m^?3 at all sites). The reduction in the number of daily exceedances of the limit value (50 μg m^?3) after subtraction of the dust contribution is also calculated at each station: it varies with station between 20% and 50% in 2005 and between 5% and 25% in 2003 and 2004.