Effect of pretreatment on Pd/Al2O3 catalyst for catalytic oxidation of o-xylene at low temperature

The effect of pretreatment on Pd/Al₂O₃ catalysts for the catalytic oxidation of o-xylene at low temperature was studied by changing the pretreatment and testing conditions. The fresh and pretreated Pd/Al₂O₃ catalysts were characterized by transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD). The results showed that the pretreatment dramatically changed the Pd/PdO ratio and then significantly affected the Pd/Al₂O₃ activity; while the pretreatment had not much influence on Pd particle size. The Pd/Al₂O₃ pre-reduced at 300℃/400℃, which has fully reduced Pd species, showed the highest activity; while the fresh Pd/Al₂O₃, which has fully oxidized Pd species, presented the worst performance, indicating the Pd chemical state plays an important role in the catalytic activity for the o-xylene oxidation. It is concluded that metallic Pd is the active species on the Pd/Al₂O₃ catalyst for the catalytic oxidation of o-xylene at low temperature.     

Catalytic oxidation of benzene over nanostructured porous Co3O4-CeO2 composite catalysts

The three-dimensional structured Co₃O₄-CeO₂ oxides with Co/Ce molar ratio 16:1 gave the highest catalytic activity, which provided more surface hydroxyl groups and more surface oxygenated species.     

Effect of Ce doping of TiO2 support on NH3-SCR activity over V2O5-WO3/CeO2-TiO2 catalyst

CeO2–TiO2composite supports with different Ce/Ti molar ratios were prepared by a homogeneous precipitation method, and V2O5–WO3/CeO2–TiO2catalysts for the selective catalytic reduction（SCR） of NOx with NH3 were prepared by an incipient-wetness impregnation method. These catalysts were characterized by means of BET, XRD, UV–Vis,Raman and XPS techniques. The results showed that the catalytic activity of V2O5–WO3/TiO2 was greatly enhanced by Ce doping（molar ratio of Ce/Ti = 1/10） in the TiO2 support.The catalysts that were predominantly anatase TiO2 showed better catalytic performance than the catalysts that were predominantly fluorite CeO2. The Ce additive could enhance the surface adsorbed oxygen and accelerate the SCR reaction. The effects of O2 concentration, ratio of NH3/NO, space velocity and SO2 on the catalytic activity were also investigated. The presence of oxygen played an important role in NO reduction. The optimal ratio of NH3/NO was 1/1 and the catalyst had good resistance to SO2 poisoning.     

Pt/CeO2催化氧化甲苯反应机制研究

采用浸渍法制备了Pt/CeO_2和Pt/Al2O_3催化剂,并通过XRD、BET、ICP-OES、H2-TPR、XPS等手段表征其物理化学性质.结果发现,Pt/CeO_2和Pt/Al2O_3催化剂上Pt负载量约为0.6%,Al2O_3载体上Pt颗粒尺寸更小,Pt/CeO_2的可还原性更强.甲苯催化氧化活性评价结果表明,Pt/CeO_2催化剂表现出更好的催化活性,T50=170℃,T90=190℃.通过UV-Raman、甲苯TPD、GC/MS、In-situ FTIR等手段进一步研究发现,Pt/CeO_2活化甲苯及反应供氧的机制与Pt/Al2O_3存在区别,其活性更好是因为:(1)负载在CeO_2表面存在高电子密度的Pt原子,具有更强的活化甲苯能力,可以直接使苯基和甲基间的C—C链发生断裂;(2)Pt的负载促进了CeO_2氧空位形成,进一步提高了CeO_2的储氧性能,加速氧循环.除了Pt解离气相氧之外,CeO_2还可以提供活性氧物种参与催化氧化甲苯的反应,进一步提高甲苯催化氧化效率.     

富氧条件下SnO2/Al2O3催化剂上丙烯选择性还原NOx的研究

考察了分别用浸渍法、共沉淀法和溶胶-凝胶法制备的SnO₂/Al₂O₃催化剂上丙烯选择性还原NO_x的催化活性,发现制备方法与Sn的负载量对其活性有重要影响.溶胶-凝胶法制备的SnO₂/Al₂O₃催化剂活性最高,Sn的最佳负载量为5%.与浸渍法和共沉淀法制备的5%SnO₂/Al₂O₃催化剂相比,溶胶-凝胶法制备的5%SnO₂/Al₂O₃催化剂受水蒸汽的抑制作用较弱,并且在水和SO₂共存的条件下活性最高.此外,反应气中丙烯及氧气浓度的增加有利于NO_x转化率的提高.     

Mo-modified Pd/Al2O3 catalysts for benzene catalytic combustion

Mo-modified Pd/Al2O3catalysts were prepared by an impregnation method and tested for the catalytic combustion of benzene. The catalysts were characterized by N2 isothermal adsorption, X-ray diffraction（XRD）, X-ray photoelectron spectroscopy（XPS）, temperatureprogrammed desorption of NH3（NH3-TPD）, H2temperature-programmed reduction（H2-TPR）, and high-angle annular dark-field scanning transmission electron microscopy（HAADF-STEM）. The results showed that the addition of Mo effectively improved the activity and stability of the Pd/Al2O3catalyst by increasing the dispersion of Pd active components, changing the partial oxidation state of palladium and increasing the oxygen species concentration on the surface of catalyst. In the case of the Pd-Mo/Al2O3catalyst,benzene conversion of 90% was obtained at temperatures as low as 190°C, which was 45°C lower than that for similar performance with the Pd/Al2O3catalyst. Moreover, the 1.0% Pd-5% Mo/Al2O3catalyst was more active than the 2.0% Pd/Al2O3catalyst. It was concluded that Pd and Mo have a synergistic effect in benzene catalytic combustion.     

CuO对贵金属/CeO2/Al2O3催化剂的作用

制备含少量贵金属Ｐｔ、Ｐｄ的不同Ｃｕ和Ｃｅ摩尔含量比（０：１０,１：９,２：８）的催化剂,实验条件十加入ＣｕＯ可以提高Ｐｔ催化剂的二效活性;加入Ｃｕ：Ｃｅ＝２：８的ＣｕＯ降低了Ｐｄ催化剂的顾效性能,然而Ｃｕ：Ｃｅ＝１：９时可以改善Ｐｄ催化剂的三效催化性能。通过结构分析,认为ＣｕＯ的存在可以提高ｄ催化剂的比表面积,ＰｄＯ的分散度。     

Catalytic activity of cerium-doped Ru/Al2O3 during ozonation of dimethyl phthalate

In this paper, factors influencing the mineralization of dimethyl phthalate (DMP) during catalytic ozonation with a cerium-doped Ru/Al₂O₃ catalyst were studied. The catalytic contribution was calculated through the results of a comparison experiment. It showed that doping cerium significantly enhanced catalytic activity. The total organic carbon (TOC) removal over the doped catalyst at 100 min reached 75.1%, 61.3% using Ru/Al₂O₃ catalyst and only 14.0% using ozone alone. Catalytic activity reached the maximum when 0.2% of ruthenium and 1.0% of cerium were simultaneously loaded onto Al₂O₃ support. Results of experiments on oxidation by ozone alone, adsorption of the catalyst, Ce ion’s and heterogeneous catalytic ozonation confirmed that the contribution of heterogeneous catalytic ozonation was about 50%, which showed the obvious effect of Ru-Ce/Al₂O₃ on catalytic activity. __________ Translated from China Environmental Science, 2006, 26(4): 445–448 [译自: 中国环境科学]     

Effect of CeO2 and Al2O3 on the activity of Pd/Co_3O_4/cordierite catalyst in the three-way catalysis reactions (CO/NO/CnHm)

The present article studies the effect of CeO₂ and Al₂O₃ on the activity of Pd/Co₃O₄/cordierite catalyst in conversion of NO, CO, C_nH_m. The catalysts were characterized by temperature programmed reduction with hydrogen, X-ray diffraction, X-ray photoelectron spectroscopy and transmission electron microscopy. It is shown that the effect of CeO₂ on the properties of Pd/Co₃O₄/cordierite catalyst depends on preparation method. The catalyst obtained by co-deposition of cerium and cobalt oxides has higher activity in CO oxidation (CO + O₂ and CO + NO) and total hexane oxidation (C₆H₁₄ + O₂). Such phenomenon is probably caused by more than stoichiometric amount of formed oxygen vacancies, an increase in both mobility of surface oxygen and dispersity of components in the catalytic composition. It is demonstrated that CeO₂ addition promotes the SO₂ resistance of Pd/Co₃O₄/cordierite. The second support decreases the activity of Pd/Co₃O₄/cordierite catalyst in the reactions of CO and C₆H₁₄ with oxygen because of CoAl₂O₄ formation.     

Cu-Al2O3中骨架铜类芬顿催化去除水中有机污染物

为解决传统铁基芬顿催化剂在水体通常酸碱(pH6)条件下活性低的问题,采用简单共沉淀法制备了Cu掺杂的Al_2O_3类芬顿催化剂.通过X射线衍射(XRD)、X射线光电子能谱(XPS)和紫外可见(UV-vis)吸收光谱分析表明,Cu-Al_2O_3中铜掺杂的质量分数低于4.77%时,催化剂中铜主要以Cu~(2+)和Cu~+的形式共存于Al_2O_3的骨架结构中,形成Al—O—Cu键;过量的铜掺杂会导致外骨架铜物种如铜氧化物团簇的存在.以难降解有机污染物2-氯苯酚(2-chlorophenol,2-CP)和染料罗丹明B(Rhodamine B,Rh B)为目标污染物,对Cu-Al_2O_3的类芬顿催化性能进行了详细地研究.结果表明,骨架铜物种在中性温和条件下对2-CP和Rh B显示出很高的催化去除效率和稳定性,反应2 h,Cu-Al_2O_3(Cu质量分数4.77%)对2-CP的去除率达到54%,相应的TOC去除率达到49%,而铜离子溶出浓度仅为0.025 5 mg·L-1,而Cu-Al_2O_3(Cu质量分数7.58%)由于外骨架铜的存在导致催化活性增加缓慢和稳定性下降.ESR测试结果表明,·OH和HO_2~-/O_2~-·是反应中主要的活性物种.     

Characterization and performance of Pt/SBA-15 for low-temperature SCR of NO by C3H6

Pt supported on mesoporous silica SBA-15 was investigated as a catalyst for low temperature selective catalytic reduction(SCR) of NO by C 3 H 6 in the presence of excess oxygen.The prepared catalysts were characterized by means of XRD,BET surface area,TEM,NO-TPD,NO/C 3 H 6-TPO,NH 3-TPD,XPS and 27 Al MAS NMR.The effects of Pt loading amount,O 2 /C 3 H 6 concentration,and incorporation of Al into SBA-15 have been studied.It was found that the removal efficiency increased significantly after Pt loading,but an optimal loading amount was observed.In particular,under an atmosphere of 150 ppm NO,150 ppm C 3 H 6,and 18 vol.% O 2,0.5% Pt/SBA-15 showed remarkably high catalytic performance giving 80.1% NOx reduction and 87.04% C 3 H 6 conversion simultaneously at 140°C.The enhanced SCR activity of Pt/SBA-15 is associated with its outstanding oxidation activities of NO to NO 2 and C 3 H 6 to CO 2 in low temperature range.The research results also suggested that higher concentration of O 2 and higher concentration of C 3 H 6 favored NO removal.The incorporation of Al into SBA-15 improved catalytic performance,which could be ascribed to the enhancement of catalyst surface acidity caused by tetrahedrally coordinated AlO 4.Moreover,the catalysts could be easily reused and possessed good stability.     

SO2对Ag/Al2O3催化剂上CH3OH还原NO性能的影响

用溶胶-凝胶混合法制备了Ag负载量为5%的Ag/A1₂O₃催化剂.研究了富氧条件下,SO₂对CH₃OH在催化剂上还原NO性能的影响.结果表明,反应气不含SO₂和H₂O时,NO还原活性温度较低,有显著量N₂O生成,这被归因为反应过程中,部分氧化态Ag被还原为金属Ag.添加SO₂或同时添加SO₂和H_{2相似文献}   

V2O5/TiO2催化剂中毒机理的试验研究

选择性催化还原(SCR)催化剂是SCR烟气脱硝技术的核心,是整个SCR系统脱硝效率和经济性的决定因素.本文工作的主要研究思路是以钒钛SCR催化剂为研究对象,研究了H2O和SO2,以及相同含量下K、Na、Ca、Pb的氧化物对钒钛催化剂NO转化率的影响.H2O的存在会抑制V2O5/TiO2催化剂脱硝活性,而SO2在一定程度上促进(V2O5/TiO2)催化剂的SCR脱硝反应,提高NO转化率;碱金属K对钒钛催化剂的钝化作用都是最强,K2O和Na2O的掺入会抑制钒钛催化剂上V2O5的还原能力,而CaO和PbO的掺入对钒钛催化剂上V2O5的还原能力影响较小.     

Fe2O3添加对钛基SCR催化剂表面硫酸氢铵分解行为的影响规律

采用共沉淀法合成了TiO_2及TiO_2-Fe_2O_3载体,并对硫酸氢铵与上述载体之间的相互作用及硫酸氢铵的具体分解行为进行了研究.结果表明,催化剂载体表面含硫官能团主要以双齿硫酸盐的形式存在,含氮官能团以铵根离子的形式存在.当硫酸氢铵沉积于催化剂载体表面时,由于硫酸根离子具有较强的电负性,Ti原子及Fe原子处于电子缺失状态.对于TiO_2载体,硫酸根离子主要与Ti原子相连;而对于TiO_2-Fe_2O_3载体,Ti原子及Fe原子均为硫酸根离子主要的附着位点.采用热分析方法及原位红外对硫酸氢铵在TiO_2及TiO_2-Fe_2O_3载体表面的分解行为进行了研究,发现铁氧化物的添加显著促进了硫酸氢铵在低温区间内的分解行为;与铵根离子相比,硫酸根离子具有更高的热稳定性.催化剂稳定性测试结果表明,铁氧化物的添加显著提高了低温抗硫抗水性能,为实现低温SCR技术的工业应用提供了理论基础.     

Ce-Mn/Al2O3-H2O2催化氧化皮革废水的研究

以浸渍法制备了Ce-Mn/Al_2O_3催化剂,研究该催化剂在H_2O_2非均相类Fenton体系中对皮革废水污染物的催化降解性能.在单因素试验的基础上,以COD去除率为响应值,采用Box-Behnken响应曲面法考察了催化剂投加量、H_2O_2投加量、初始pH、反应时间等4个因素之间的单独作用及交互作用,实验数据用Design-Expert 8.0.6软件进行处理,得到二次响应曲面模型.结果表明,4个独立变量对响应值的影响顺序如下:初始pHH_2O_2投加量催化剂投加量反应时间,数学模型拟合度高(R_(adj)~2=0.9349),利用该模型预测的最大COD去除率为78.86%,最佳反应条件为:催化剂投加量56.63 g·L~(-1),H_2O_2投加量315.15 mg·L~(-1),初始pH3.51,反应时间2 h,经实验验证COD去除率为80.94%,与模型预测值偏差2.08%.     

Fe2O3 particles as superior catalysts for low temperature selective catalytic reduction of NO with NH3

Fe203 particle catalysts were experimentally studied in the low temperature selective catalytic reduction （SCR） of NO with NH3. The effects of reaction temperature, oxygen concentration, [NH3]/[NO] molar ratio and residence time on SCR activity were studied. It was found that Fe203 catalysts had high activity for the SCR of NO with NH3 in a broad temperature range of 150-270℃, and more than 95% NO conversion was obtained at 180℃ when the molar ratio [NH3]/[NO] = 1, the residence time was 0.48 seconds and 02 volume fraction was 3%. In addition, the effect of SO2 on SCR catalytic activity was also investigated at the temperature of 180℃. The results showed that deactivation of the Fe2O3 particles occurred due to the presence of SO2 and the NO conversion decreased from 99.2% to 58% in 240 min, since SO2 gradually decreased the catalytic activity of the catalysts. In addition, X-ray diffraction, Thermogravimetric analysis and Fourier transform infrared spectroscopy were used to characterize the fresh and deactivated Fe2O3 catalysts. The results showed that the deactivation caused by SO2 was due to the formation of metal sulfates and ammonium sulfates on the catalyst surface during the de-NO reaction, which could cause pore plugging and result in suppression of the catalytic activity.     

Pd/Al2O3粒子电极电催化还原BrO3-的研究

针对常规方法难以去除水中Br_3~-的问题,采用浸渍煅烧法制备了负载型纳米Pd/Al_2O_3粒子电极,研究了该电极电催化还原Br O-3的效果.催化剂的结构表征表明该反应实现了Pd纳米晶的均匀负载,纳米Pd/Al_2O_3具有较高的电催化活性和较低的能耗,其最佳反应条件为3%Pd负载量,0.9 m A·cm-2电流密度和1 g·L催化剂投量,酸性条件可促进Br O-3的直接或间接还原.ESR检测证实了Pd的负载增强了反应体系活性物种[H]的生成,进而促进了Br O-3的间接电催化还原.     

Preparation and characterization of Pd/Fe bimetallic nanoparticles immobilized on Al2O3/PVDF membrane: Parameter optimization and dechlorination of dichloroacetic acid

Using a liquid–solid phase inversion method, a hybrid matrix poly(vinylidene fluoride)(PVDF) membrane was prepared with alumina(Al2O3) nanoparticle addition. Pd/Fe nanoparticles(NPs) were successfully immobilized on the Al2O3/PVDF membrane, which was characterized by Scanning Electron Microscopy(SEM) and Transmission Electron Microscopy(TEM). The micrographs showed that the Pd/Fe NPs were dispersed homogeneously. Several important experimental parameters were optimized, including the mechanical properties, contact angle and surface area of Al2O3/PVDF composite membranes with different Al2O3 contents. At the same time, the ferrous ion concentration and the effect of hydrophilization were studied. The results showed that the modified Al2O3/PVDF membrane functioned well as a support. The Al2O3/PVDF membrane with immobilized Pd/Fe NPs exhibited high efficiency in terms of dichloroacetic acid(DCAA) dechlorination. Additionally, a reaction pathway for DCAA dechlorination by Pd/Fe NPs immobilized on the Al2O3/PVDF membrane system was proposed.     

Ag改性石墨相氮化碳(g-C3N4)可见光辅助活化过一硫酸盐降解罗丹明B

采用煅烧法和光还原法制备出具有高活性的Ag/g-C₃N₄催化剂,并将其应用于可见光下活化过一硫酸盐（PMS）降解罗丹明B（RhB）废水.系统研究了实际因素RhB浓度、催化剂投加量、PMS剂量、pH值和可溶性无机阴离子对RhB降解效果的影响.结果表明,RhB的降解率随着催化剂投加量、PMS浓度的增加而增大,随着初始RhB浓度的增加而减小.弱酸性条件有利于反应活化PMS降解RhB,而中性或碱性条件都会减缓催化反应的进行.Ag/g-C₃N₄-2/Vis/PMS催化体系30 min内对RhB的去除率最高可达93.2%,分别是Ag/g-C₃N₄/Vis和单独PMS催化体系的4.0和3.7倍.体系催化活性的提高归因于Ag的表面等离子共振效应及基于硫酸根自由基的高级氧化技术与光催化技术的协同作用.不同阴离子对催化反应的影响不同,溶液中的Cl^-会对反应产生轻微的抑制作用,而H₂PO₄^-和HCO₃^-的出现大大抑制了催化性能.催化剂具有良好的稳定性,5次循环后仍能在30 min之内降解77.4%的RhB.此外,捕获实验和ESR测试结果表明,Ag/g-C₃N₄-2/Vis/PMS催化体系中存在·O₂^-、h⁺、¹O₂、SO₄^-·和·OH活性物种,并协同降解RhB污染物.     

Efficient degradation of chlorobenzene in a non-thermal plasma catalytic reactor supported on CeO2/HZSM-5 catalysts

Chlorobenzene removal was investigated in a non-thermal plasma reactor using CeO₂/HZSM-5 catalysts. The performance of catalysts was evaluated in terms of removal and energy efficiency. The decomposition products of chlorobenzene were analyzed. The results show that CeO₂/HZSM-5 exhibited a good catalytic activity, which resulted in enhancements of chlorobenzene removal, energy efficiency, and the formation of lower amounts of by-products. With regards to CO₂ selectivity, the presence of catalysts favors the oxidation of by-products, leading to a higher CO₂ selectivity. With respect to ozone, which is considered as an unavoidable by-product in air plasma reactors, a noticeable decrease in its concentration was observed in the presence of catalysts. Furthermore, the stability of the catalyst was investigated by analyzing the evolution of conversion in time. The experiment results indicated that CeO₂/HZSM-5 catalysts have excellent stability: chlorobenzene conversion only decreased from 78% to 60% after 75 hr, which means that the CeO₂/HZSM-5 suffered a slight deactivation. Some organic compounds and chlorinated intermediates were adsorbed or deposited on the catalysts surface as shown by the results of Fourier Transform Infrared (FT-IR) spectroscopy, scanning electron microscope (SEM) and energy dispersive X-ray spectroscopy (EDS) analyses of the catalyst before and after the reaction, revealing the cause of catalyst deactivation.