Long-term behavior of municipal solid waste landfills

A method is presented to predict the long-term behavior of element concentrations (non-metals and metals) in the leachate of a municipal solid waste (MSW) landfill. It is based on water flux and concentration measurements in leachates over one year, analysis of drilled cores from MSW landfills and leaching experiments with these samples. A mathematical model is developed to predict the further evolution of annual flux-weighted mean element concentrations in leachates after the “intensive reactor phase”, i.e. after the gas production has dropped to a very low level. The results show that the organic components are the most important substances to control until the leachate is compatible with the environment. This state of low emissions, the so-called “final storage quality”, will take many centuries to be achieved in a moderate climate.     

Forest products decomposition in municipal solid waste landfills

Cellulose and hemicellulose are present in paper and wood products and are the dominant biodegradable polymers in municipal waste. While their conversion to methane in landfills is well documented, there is little information on the rate and extent of decomposition of individual waste components, particularly under field conditions. Such information is important for the landfill carbon balance as methane is a greenhouse gas that may be recovered and converted to a CO(2)-neutral source of energy, while non-degraded cellulose and hemicellulose are sequestered. This paper presents a critical review of research on the decomposition of cellulosic wastes in landfills and identifies additional work that is needed to quantify the ultimate extent of decomposition of individual waste components. Cellulose to lignin ratios as low as 0.01-0.02 have been measured for well decomposed refuse, with corresponding lignin concentrations of over 80% due to the depletion of cellulose and resulting enrichment of lignin. Only a few studies have even tried to address the decomposition of specific waste components at field-scale. Long-term controlled field experiments with supporting laboratory work will be required to measure the ultimate extent of decomposition of individual waste components.     

Modeling of perched leachate zone formation in municipal solid waste landfills

The paper presents a 1D mathematical model for the simulation of the percolation fluxes throughout a landfill for municipal solid waste (MSW). Specifically, the model was based on mass balance equations, that enable simulation of the formation of perched leachate zones in a landfill for MSW. The model considers the landfill divided in several layers evaluating the inflow to and outflow from each layer as well as the continuous moisture distribution. The infiltration flow was evaluated by means of the Darcy’s law for an unsaturated porous medium, while the moisture distribution evaluation has been carried out on the basis of the theory of the vertically distributed unsaturated flow. The solution of the model has been obtained by means of the finite difference method. The model has been applied to a semi-idealized landfill located in Palermo landfill (Bellolampo). Specifically, field measurements were conducted to determine the relationship between waste density and applied vertical strain. This relationship was then used to relate vertical strain to waste porosity. The inflow rate to the system was simulated via a synthetic hyetograph whose characteristics have been identified in a previous hydrologic study.Three simulations, each with a different initial moisture content, were conducted. The model results showed a different response of the landfill in terms both of flow rates throughout the landfill and moisture profile. Indeed, the initial moisture content drastically influenced not only the formation of perched leachate zones but also their extension. The model can be a useful tool in predicting potential for the formation of perched leachate zones.     

Modelling leachate quality and quantity in municipal solid waste landfills.

The operational phase of landfills may last for 20 years or more. Significant changes in leachate quality and generation rate may occur during this operational period. A mathematical model has been developed to simulate the landfill leachate behaviour and distributions of moisture and leachate constituents through the landfill, taking into consideration the effects of time-dependent landfill development on the hydraulic characteristics of waste and composition of leachate. The model incorporates governing equations that describe processes influencing the leachate production and biochemical processes taking place during the stabilization of wastes, including leachate flow, dissolution, acidogenesis and methanogenesis. To model the hydraulic property changes occurring during the development stage of the landfills, a conceptual modelling approach was proposed. This approach considers the landfill to consist of cells or columns of cells, which are constructed at different times, and considers each cell in the landfill to consist of several layers. Each layer is assumed to be a completely mixed reactor containing uniformly distributed solid waste, moisture, gases and micro-organisms. The use of the proposed conceptual model enables the incorporation of the spatial changes in hydraulic properties of the landfill into the model and also makes it possible to predict the spatial and temporal distributions of moisture and leachate constituents. The model was calibrated and partially verified using leachate data from Keele Valley Landfill in Ontario, Canada and data obtained from the literature. Ranges of values were proposed for model parameters applicable for real landfill conditions.     

Characterization of municipal solid waste from the main landfills of Havana city

The city of Havana, the political, administrative and cultural centre of Cuba, is also the centre of many of the economic activities of the nation: industries, services, scientific research and tourism. All of these activities contribute to the generation of municipal solid waste (MSW), which also impact other Cuban cities. Inadequate handling of waste and the lack of appropriate and efficient solutions for its final disposal and treatment increase the risk and possibility of contamination. The main difficulty in the development of a system of management of MSW lies in the lack of knowledge of the chemical composition of the waste that is generated in the country as a whole, and especially in Havana, where solid waste management decisions are made. The present study characterizes MSW in Havana city during 2004. The Calle 100, Guanabacoa and Ocho Vías landfills were selected for physical-chemical characterization of MSW, as they are the three biggest landfills in the city. A total of 16 indicators were measured, and weather conditions were recorded. As a result, the necessary information regarding the physical-chemical composition of the MSW became available for the first time in Cuba. The information is essential for making decisions regarding the management of waste and constitutes a valuable contribution to the Study on Integrated Management Plan of MSW in Havana.     

Slope failures in municipal solid waste dumps and landfills: a review

Between 1977 and 2005 six large-scale failures of municipal solid waste dumps and landfills have been recorded in the technical literature. The volumes of waste mobilized in the failures varied from 10-12 000 m(3) in a failure that killed nearly 300 people to 1.5 million m(3) in a failure that caused no deaths or injuries. Of the six failures, four occurred in dumps that, as far as is known, had not been subjected to any prior technical investigation of their shear stability. The remaining two failures occurred in engineer-designed landfills, one of which practised leachate recirculation, and the other co-disposed of liquid waste along with solid waste. The paper reviews, describes and analyses the failures and summarizes their causes.     

A review of approaches for the long-term management of municipal solid waste landfills

After closure, municipal solid waste (MSW) landfills must be managed and controlled to avoid adverse effects on human health and the environment (HHE). Aftercare (or post-closure care) can be brought to an end when the authorities consider the landfill to no longer pose a threat to HHE. Different approaches have been suggested for long-term landfill management and evaluation of aftercare completion. In this paper, research on aftercare and its completion is analyzed and regulatory approaches for the completion of landfill aftercare are reviewed. Approaches to aftercare could be categorized as (i) target values, (ii) impact/risk assessment, and (iii) performance based. Comparison of these approaches illustrates that each has limitations and strengths. While target values are typically used as screening indicators to be complemented with site-specific assessments, impact/risk assessment approaches address the core issue about aftercare completion, but face large uncertainties and require a high level of expertise. A performance-based approach allows for the combination of target values and impact/risk assessments in a consistent evaluation framework with the aim of sequentially reducing aftercare intensity and, ultimately, leading to the completion of aftercare. At a regulatory level, simple qualitative criteria are typically used as the primary basis for defining completion of aftercare, most likely due to the complexity of developing rigorous evaluation methodologies. This paper argues that development of transparent and consistent regulatory procedures represents the basis for defining the desired state of a landfill at the end of aftercare and for reducing uncertainty about the intensity and duration of aftercare. In this context, recently presented technical guidelines and the ongoing debate with respect to their regulatory acceptance are a valuable step towards developing strategies for the cost-effective protection of HHE at closed MSW landfills. To assess the practicality of evaluation methodologies for aftercare, well-documented case studies including regulatory review and acceptance are needed.     

Two-year performance by evapotranspiration covers for municipal solid waste landfills in northwest Ohio

Evapotranspiration (ET) covers have gained interest as an alternative to conventional covers for the closure of municipal solid waste (MSW) landfills because they are less costly to construct and are expected to have a longer service life. Whereas ET covers have gained acceptance in arid and semi-arid regions (defined by a precipitation (P) to potential evapotranspiration (PET) ratio less than 0.75) by meeting performance standards (e.g. rate of percolation), it remains unclear whether they are suitable for humid regions (P:PET greater than 0.75). The goal of this project is to extend their application to northwest Ohio (P:PET equals 1.29) by designing covers that produce a rate of percolation less than 32 cm yr^?1, the maximum acceptable rate by the Ohio Environmental Protection Agency (OEPA). Test ET covers were constructed in drainage lysimeters (1.52 m diameter, 1.52 m depth) using dredged sediment amended with organic material and consisted of immature (I, plants seeded onto soil) or mature (M, plants transferred from a restored tall-grass prairie) plant mixtures. The water balance for the ET covers was monitored from June 2009 to June 2011, which included measured precipitation and percolation, and estimated soil water storage and evapotranspiration. Precipitation was applied at a rate of 94 cm yr^?1 in the first year and at rate of 69 cm yr^?1 in the second year. During the first year, covers with the M plant mixture produced noticeably less percolation (4 cm) than covers with the I plant mixture (17 cm). However, during the second year, covers with the M plant mixture produced considerably more percolation (10 cm) than covers with the I plant mixture (3 cm). This is likely due to a decrease in the aboveground biomass for the M plant mixture from year 1 (1008 g m^?2) to year 2 (794 g m^?2) and an increase for the I plant mixture from year 1 (644 g m^?2) to year 2 (1314 g m^?2). Over the 2-year period, the mean annual rates of percolation for the covers with the M and I plant mixtures were 7 and 8 cm yr^?1, which are below the OEPA standard. The results suggest the application of ET covers be extended to northwest Ohio and other humid regions.     

Environmental diagnosis methodology for municipal waste landfills

A large number of countries are involved in a process of transformation with regard to the management of municipal solid waste. This process is a consequence of environmental requirements that occasionally materialise in legislation, such as the European Council Directive 31/99/EC on waste release in the European Union. In some cases, the remediation of old landfills can be carried out in compliance with environmental requirements; in other cases, it is necessary to proceed with the closure of the landfill and to assimilate it into its own environment. In both cases, it is necessary to undertake a diagnosis and characterisation of the impacted areas in order to develop an adequate action plan. This study presents a new methodology by which environmental diagnosis of landfill sites may be carried out. The methodology involves the formulation of a series of environmental indeces which provide information concerning the potential environmental problems of the landfills and the particular impact on different environmental elements, as well as information related to location, design and operation. On the basis of these results, it would be possible to draw up action plans for the remediation or closure of the landfill site. By applying the methodology to several landfills in a specific area, it would be possible to prioritize the order of actions required.     

Phytoremediation and rehabilitation of municipal solid waste landfills and dumpsites: A brief review

Environmental problems posed by municipal solid waste (MSW) are well documented. Scientifically designed landfills and/or open dumpsites are used to dispose MSW in many developed and developing countries. Non-availability of land and need to reuse the dumpsite space, especially in urban areas, call for rehabilitation of these facilities. A variety of options have been tried to achieve the goals of rehabilitation. In the last couple of decades, phytoremediation, collectively referring to all plant-based technologies using green plants to remediate and rehabilitate municipal solid waste landfills and dumpsites, has emerged as a potential candidate. Research and development activities relating to different aspects of phytoremediation are keeping the interest of scientists and engineers alive and enriching the literature. Being a subject of multi-disciplinary interest, findings of phytoremediation research has resulted in generation of enormous data and their publication in a variety of journals and books. Collating data from such diverse sources would help understand the dynamics and dimensions of landfill and dumpsite rehabilitation. This review is an attempt in this direction.     

Achieving "Final Storage Quality" of municipal solid waste in pilot scale bioreactor landfills

Entombed waste in current sanitary landfills will generate biogas and leachate when physical barriers fail in the future, allowing the intrusion of moisture into the waste mass contradicting the precepts of the sustainability concept. Bioreactor landfills are suggested as a sustainable option to achieve Final Storage Quality (FSQ) status of waste residues; however, it is not clear what characteristics the residues should have in order to stop operation and after-care monitoring schemes. An experiment was conducted to determine the feasibility to achieve FSQ status (Waste Acceptance Criteria of the European Landfill Directive) of residues in a pilot scale bioreactor landfill. The results of the leaching test were very encouraging due to their proximity to achieve the proposed stringent FSQ criterion after 2 years of operation. Furthermore, residues have the same characteristics of alternative waste stabilisation parameters (low BMP, BOD/COD ratio, VS content, SO4(2-)/Cl- ratio) established by other researchers. Mass balances showed that the bioreactor landfill simulator was capable of practically achieving biological stabilisation after 2 years of operation, while releasing approximately 45% of the total available (organic and inorganic) carbon and nitrogen into the liquid and gas phases.     

Application of tire chips to reduce the temperature of secondary geomembranes in municipal solid waste landfills

Heat generated by the biodegradation of waste and other chemical processes in a landfill can potentially affect the long-term performance of landfill liner system, in particular that of a high-density polyethylene geomembrane. In a double liner system, the difference in leachate exposure and temperature might improve the long-term performance of the secondary geomembrane compared to that of the primary geomembrane. However, in some cases, the temperature is likely to be high enough to substantially reduce the service-life of the secondary geomembrane. This study explores the possible effectiveness of using tire chips as thermal insulation between primary and secondary liners to reduce the temperature of secondary geomembranes as compared to traditional soil materials. Heat and contaminant migration analyses are performed for cases with no insulation and for cases in which a layer of soil or tire chips has been used as thermal insulation between the primary and secondary liners. The effect of insulation on prolonging the service-life of a secondary geomembrane and, consequently, on contaminant transport through a liner system is examined for the case of a volatile organic compound (dichloromethane) found in landfill leachate. The study suggests that the use of tire chips warrants consideration, however there are other practical issues that require consideration in the detailed design and construction of landfill liners. Issues such as finite service-life, low working temperature, excessive settlement, ability to generate internal heat, leaching of tire chips and limitations in performing electrical resistivity leak detection tests are identified.     

The effects of daily cover soils on shear strength of municipal solid waste in bioreactor landfills

Bioreactor landfills are operated to enhance refuse decomposition, gas production, and waste stabilization. The major aspect of bioreactor landfill operation is the recirculation of collected leachate back through the refuse mass. Due to the accelerated decomposition and settlement of solid waste, bioreactor landfills are gaining popularity as an alternative to the conventional landfill. The addition or recirculation of leachate to accelerate the waste decomposition changes the geotechnical characteristics of waste mass. The daily cover soils, usually up to 20–30% of total MSW volumes in the landfill, may also influence the decomposition and shear strength behavior of MSW. The objective of this paper is to study the effects of daily covers soils on the shear strength properties of municipal solid waste (MSW) in bioreactor landfills with time and decomposition. Two sets of laboratory-scale bioreactor landfills were simulated in a laboratory, and samples were prepared to represent different phases of decomposition. The state of decomposition was quantified by methane yield, pH, and volatile organic content (VOC). Due to decomposition, the matrix structure of the degradable solid waste component was broken down and contributed to a significant decrease in the reinforcing effect of MSW. However, the daily cover soil, a non-degradable constituent of MSW, remains constant. Therefore, the interaction between daily cover soil particles and MSW particles will affect shear strength behavior. A number of triaxial tests were performed to evaluate the shear strength of MSW. The test results indicated that the shear strength of MSW was affected by the presence of cover soils. The friction angle of MSW with the presence of cover soil is higher than the friction angle of MSW without any cover soils. The friction angle of MSW increased from 27° to 30° due to the presence of cover soils for Phase 1 samples. The increased strength was attributed to the friction nature of sandy soil that was used as daily covers soils. Therefore, the effects of cover soils on the shear strength properties of MSW should be evaluated and taken into consideration during stability analyses and design.     

Sensitivity analysis and literature review of parameters controlling local biodegradation processes in municipal solid waste landfills

The local gas production rate in municipal landfills is influenced by a large number of processes, which have been modelled by a local mechanistic reaction model based on Monod kinetics. This type of model, however, requires over 40 input parameters. The aim of this research was to review published values for these input parameters, and to analyse the sensitivity of the model to changes in each of them. Included were rate constants based on Monod kinetics, general rate-controlling variables, and parameters that influence the local pH and temperature of the waste. Mathematical functions that describe the influence of water content, temperature, and pH on biodegradation rates were calibrated on the basis of literature data. The results of the sensitivity analysis suggest that the parameters with the largest impact on model output are the hydrolysis constant k(Hy), the kinetic constants [Formula: see text] , [Formula: see text] , [Formula: see text] , K(i,ac,Hy), and [Formula: see text] , the water content, temperature, pH, initial concentration of X(me), the enthalpy of formation of the original organic matter, as well as the protein content and buffering capacity of the waste. These parameters, therefore, should be carefully selected when similar modelling studies are performed.     

Biostabilization of municipal solid waste

A mechanical-biological process for municipal solid waste (MSW) treatment was monitored for one year. Mechanical pre-treatment provided two fractions. The oversize fraction (diameter > 50 mm) (yield of 600 g kg(-1) ww) (46 Mg day(-1)) was used for refuse derived fuel production, after undergoing a mechanical refining processes, because of low moisture content (200-250 g kg(-1)) and high calorific value (2500-2800 kcal kg ww(-1)). The undersize fraction (diameter < 50 mm) (yield 400 g kg(-1) ww) (30 Mg day(-1)) contained about 800 g kg(-1) of the MSW organic matter. This fraction was biologically treated using an aerobic process with an organic waste fraction from separate collection (77 Mg day(-1)) and recycled stabilized material (62 Mg day(-1)) obtained from end-product sieve (diameter < 20 mm) used as bulking agent. A retention time of three weeks was sufficient to obtain stabilized products in agreement with up-dated rules of the Lombardy Region (North Italy) regarding biostabilization and composting processes. Dynamic Respiration Index (DRI), such as required by both Lombardy Region rules and suggested by the European Community, was chosen in preference to other indices in order to assess the degree of biological stability of the end products. A mean DRI value of 1164 mg O2 kg SV(-1) h(-1) was obtained and is in agreement with the proposed limit of 1000+/-200 mg O2 kg SV(-1) h(-1). Self-heating test, potential biogas production and fermentable volatile solids were also used as parameters to describe the potential impact of treated waste, providing further useful information. Nevertheless, all of these methods revealed analytical or interpretative limits. A complete mass balance of the biological treatment section showed that, from a net input of 107 Mg day(-1), only 250 g kg(-1) (27 Mg day(-1)) of the waste needed to be landfilled, with 750 g kg(-1) (80 Mg day(-1)) being lost as CO2 and H2O.     

The municipal solid waste system and solid waste characterization at the municipality of Veles, Macedonia

A short-term study to characterize the solid waste stream in the Municipality of Veles, Macedonia, was performed during a 1 week period in the summer of 2002. In this study, several important parameters of the municipal solid waste stream were assessed. It was estimated that the average daily generation rate is 1.06+/-0.56 kg/cap/day, while the specific weights of the uncompacted and compacted solid waste are approximately 140.5 kg/m3 and 223 kg/m3, respectively. Furthermore, it was estimated that the daily generated volume of uncompacted waste is 7.5+/-4 L/cap/day. Although the short-term study is characterized by numerous limitations, in the absence of other existing data, such a study with direct measurements could significantly contribute to the development of an efficient solid waste management system in countries with economies in transition like Macedonia.     

Settlement analysis of fresh and partially stabilised municipal solid waste in simulated controlled dumps and bioreactor landfills

The patterns of settlement of fresh as well as partially stabilised municipal solid waste (MSW), undergoing degradation in five different landfill lysimeters, were studied elaborately. The first two lysimeters, R1 and R2, contained fresh MSW while the other three lysimeters, R3, R4 and R5, contained partially stabilised MSW. R1 and R3 simulated conventional controlled dumps with fortnightly disposal of drained leachate. R2 and R4 simulated bioreactor landfills with leachate recirculation. Fortnightly water flushing was done in R5. Settlement of MSW, monitored over a period of 58 weeks, was correlated with the organic carbon content of leachate and residual volatile matter in the MSW to establish the relationship between settlement and organic destruction. Compressibility parameters such as modulus of elasticity and compression indices were determined and empirical equations were applied for the settlement data. Overall settlements up to 49% were observed in the case of landfill lysimeters, filled with fresh MSW. Landfill lysimeters with liquid addition, in the form of leachate or water, experienced lower primary settlements and higher secondary settlements than conventional fills, where no liquid addition was practised. Modified secondary compression indices for MSW in lysimeters with leachate recirculation and flushing were 30%-44% higher than that for lysimeters where no liquid addition was done. Secondary settlements in bioreactor landfills were found to vary exponentially with time.     

Enzymatic processing of municipal solid waste

The focus of this work was to investigate an enzymatic liquefaction of MSW organics, paper and cardboard. Liquefaction trials were conducted in different trial volumes: 50 g lab-scale trials and 50 kg vessel-tests and evaluated based on particle size and viscosity. The viscosity results showed that Celluclast 1.5 L had the singular significant effect on liquefaction of model MSW. No effect of α-amylase, protease and interaction in between and with cellulases on viscosity and particle size distribution was found in this study. Degradable material with a particle size above 1 mm after treatment was evaluated using SEM microscopy. These results showed that paper particles were the main obstacles needing additional treatment in order to become fully liquefied. In a pilot scale test treating authentic MSW; more than 90% of initial organic and paper dry matter (DM) was recovered as liquid slurry after sieving through a 5-mm sieve. These tests were performed at up to 35% DM, showing that this process can easily manage high DM loadings. MSW enzymatic liquefaction promotes the separation of organics and paper from solids, which facilitate the use of these degradable fractions, with minimal loss, capable to enter a biogas plant through existing pipes.     

Heating value of municipal solid waste

This paper describes the processes that are used to calculate the heating value of municipal solid waste in France. The calculation can be done either by using the thermal-balance method of a furnace or a furnace-boiler unit, or by sorting the refuse and calculating the heating value of the homogeneous components. Both methods are described in this paper. The first method measures the heating value of the refuse that is injected into the furnace; the furnace becomes a calorimeter in which thermal balance is achieved on measuring the input and output heats. The second method consists of sorting a 100 kg refuse sample into piles that are as homogeneous as possible so that it can be considered as unchanging. The heating value is determined for each component and the lower heating value of the whole sample is calculated. The advantages and drawbacks of both methods are discussed.     

A performance-based system for the long-term management of municipal waste landfills

Landfills have been the dominant alternative for disposal of solid waste and there are tens of thousands of closed landfills throughout the world that require a long-term management strategy. In contrast to approaches based on time or target values, this paper describes a performance-based methodology for evaluation of post-closure care (PCC). Using the methodology, critical components of PCC at a landfill, including leachate and gas management, groundwater monitoring and cover integrity, are considered to determine whether a landfill meets defined conditions for functional stability and can transition from regulated PCC to a post-regulatory custodial care program representing de minimus care activities only. The methodology is predicated on understanding the biological, chemical, and physical behavior of a landfill and the presence of sufficient data to verify expected trends in landfill behavior. If an evaluation suggests that a change can be made to PCC, the landfill owner must perform confirmation monitoring and then surveillance monitoring at a decreasing frequency to verify that the change is protective of human health and the environment. A hypothetical case study showed that using the methodology to evaluate site-specific PCC requirements could result in increased environmental protection at comparable cost by spending available funds where they are most needed.