Leaching mechanisms of Cr(VI) from chromite ore processing residue

Batch leaching tests, qualitative and quantitative x-ray powder diffraction (XRPD) analyses, and geochemical modeling were used to investigate the leaching mechanisms of Cr(VI) from chromite ore processing residue (COPR) samples obtained from an urban area in Hudson County, New Jersey. The pH of the leaching solutions was adjusted to cover a wide range between 1 and 12.5. The concentration levels for total chromium (Cr) and Cr(VI) in the leaching solutions were virtually identical for pH values >5. For pH values <5, the concentration of total Cr exceeded that of Cr(VI) with the difference between the two attributed to Cr(III). Geochemical modeling results indicated that the solubility of Cr(VI) is controlled by Cr(VI)-hydrocalumite and Cr(VI)-ettringite at pH >10.5 and by adsorption at pH <8. However, experimental results suggested that Cr(VI) solubility is controlled partially by Cr(VI)-hydrocalumite at pH >10.5 and by hydrotalcites at pH >8 in addition to adsorption of anionic chromate species onto inherently present metal oxides and hydroxides at pH <8. As pH decreased to <10, most of the Cr(VI) bearing minerals become unstable and their dissolution contributes to the increase in Cr(VI) concentration in the leachate solution. At low pH ( <1.5), Cr(III) solid phases and the oxides responsible for Cr(VI) adsorption dissolve and release Cr(III) and Cr(VI) into solution.     

Microbial reduction of hexavalent chromium under vadose zone conditions

Hexavalent chromium [Cr(VI)] is a common contaminant associated with nuclear reactors and fuel processing. Improper disposal at facilities in and and semiarid regions has contaminated underlying vadose zones and aquifers. The objectives of this study were to assess the potential for immobilizing Cr(VI) using a native microbial community to reduce soluble Cr(VI) to insoluble Cr(III) under conditions similar to those in the vadose zone, and to evaluate the potential for enhancing biological Cr(VI) reduction through nutrient addition. Batch microcosm and unsaturated flow column experiments were performed. Native microbial communities in subsurface sediments with no prior Cr(VI) exposure were shown to be capable of Cr(VI) reduction. In both the batch and column experiments, Cr(VI) reduction and loss from the aqueous phase were enhanced by adding high levels of both nitrate (NO3-) and organic C (molasses). Nutrient amendments resulted in up to 87% reduction of the initial 67 mg L(-1) Cr(VI) in an unsaturated batch experiment. Molasses and nitrate additions to 15 cm long unsaturated flow columns receiving 65 mg L(-1) Cr(VI) resulted in microbially mediated reduction and immobilization of 10% of the Cr during a 45-d experiment. All of the immobilized Cr was in the form of Cr(III), as shown by XANES analysis. This suggests that biostimulation of microbial Cr(VI) reduction in vadose zones by nutrient amendment is a promising strategy, and that immobilization of close to 100% of Cr contamination could be achieved in a thick vadose zone with longer flow paths and longer contact times than in this experiment.     

Utilization of waste product (tamarind seeds) for the removal of Cr(VI) from aqueous solutions: Equilibrium, kinetics, and regeneration studies

In the present study, an adsorbent was prepared from tamarind seeds and used after activation for the removal of Cr(VI) from aqueous solutions. The tamarind seeds were activated by treating them with concentrated sulfuric acid (98% w/w) at a temperature of 150 °C. The adsorption of Cr(VI) was found to be maximum at low values of initial pH in the range of 1–3. The adsorption process of Cr(VI) was tested with Langmuir, Freundlich, Redlich–Peterson, Koble–Corrigan, Tempkin, Dubinin–Radushkevich and Generalized isotherm models. Application of the Langmuir isotherm to the system yielded a maximum adsorption capacity of 29.7 mg/g at an equilibrium pH value ranging from 1.12 to 1.46. The adsorption process followed second-order kinetics and the corresponding rate constants obtained were 2.605 × 10⁻³, 0.818 × 10⁻³, 0.557 × 10⁻³ and 0.811 × 10⁻³ g/mg min⁻¹ for 50, 200, 300 and 400 mg/L of initial Cr(VI) concentration, respectively. The regenerated activated tamarind seeds showed more than 95% Cr(VI) removal of that obtained using the fresh activated tamarind seeds. A feasible solution is proposed for the disposal of the contaminants (acid and base solutions) containing high concentrations of Cr(VI) obtained during the regeneration (desorption) process.     

Effects of plants on the removal of hexavalent chromium in wetland sediments

The effect of two wetland plants, Typha latifolia L. (cattail) and Phragmites australis (Cav.) Trin. ex Steud (common reed), on the fate of Cr(VI) in wetland sediments was investigated using greenhouse bench-scale microcosm experiments. The removal of Cr(VI) was monitored based on the vertical profiles of aqueous Cr(VI) in the sediments. The Cr(VI) removal rates were estimated taking into account plant transpiration, which was found to significantly concentrate dissolved species in the sediments. After correcting for evapotranspiration, the actual Cr(VI) removal rates were significantly higher than would be inferred from uncorrected profiles. On average, the Cr(VI) removal rates were 0.005 to 0.017 mg L(-1) d(-1), 0.0003 to 0.08 mg L(-1) d(-1), and 0.004 to 0.13 mg L(-1) d(-1) for the control, T. latifolia, and P. australis microcosms, respectively. The fate of the removed Cr(VI) was examined by determining the quantity and chemical speciation of the Cr in the sediment and plant materials. Chromium(III) was the dominant form of Cr in both the sediment and plants, and precipitation of Cr(III) in the sediment was the major pathway responsible for the disappearance of aqueous Cr(VI) from the pore water. Incubation results showed that abiotic reduction was the primary mechanism underlying Cr(VI) removal in the microcosm sediments. Organic compounds produced by plants, including root exudates and mineralization products of dead roots, are thought to be the factor that is either directly or indirectly responsible for the gap between Cr(VI) removal efficiencies in the sediments of the vegetated and unvegetated microcosms.     

Sorption of hazardous metals from single and multi-element solutions by saltbush biomass in batch and continuous mode: interference of calcium and magnesium in batch mode

Batch studies were performed to determine the interference of calcium (Ca) and magnesium (Mg) on the sorption of Cu(II), Cd(II), Cr(III), Cr(VI), Pb(II), and Zn(II) [from CuSO(4), K(2)Cr(2)O(7), Pb(NO(3))(2), Cr(NO(3))(3), ZnCl(2), and Cd(NO(3))(2)] by saltbush (Atriplex canescens) biomass. The results demonstrated that Ca and Mg at concentrations of at least 20 times higher than the concentration of most of the target metals did not interfere with the metal binding. The data show that the batch binding capacity from a multimetal solution at pH 5.0 was (micromol/g) about 260 for Cr(III) and Pb, and about 117, 54, and 49 for Cu, Zn, and Cd, respectively. The use of 0.1M HCl allowed the recovery of 85-100% of the bound Cu, Cr(III), and Pb, and more than 37% of the bound Cd and Zn. The column binding capacity for Pb was about 49 micromol/g from both the single and multimetal solutions, while it was, respectively about 35 and 23 micromol/g for Cr(III). The binding capacity for Cu and Zn from the single and multimetal column experiments was 35 micromol/g and less than 10 micromol/g, respectively. The stripping data from the single column experiment showed that 0.1M HCl allowed the recovery of all the bound Cu and Zn, 90% and 74% of the bound Pb and Cr(VI), respectively, and less than 25% of the bound Cd and Cr(III), while the stripping from the multimetal experiment showed that 0.1M HCl allowed the recovery of all the bound Cu and about 74%, 54%, 43%, and 40% of the bound Pb, Zn, Cd, and Cr(III), respectively.     

Chromate reduction by chromium-resistant bacteria isolated from soils contaminated with dichromate

Extensive use of hexavalent chromium [Cr(VI)] in various industrial applications has caused substantial environmental contamination. Chromium-resistant bacteria isolated from soils can be used to remove toxic Cr(VI) from contaminated environments. This study was conducted to isolate chromium-resistant bacteria from soils contaminated with dichromate and describes the effects of some environmental factors such as pH, temperature, and time on Cr(VI) reduction and resistance. We found that chromium-resistant bacteria can tolerate 2500 mg L(-1) Cr(VI), but most of the isolates tolerated and reduced Cr(VI) at concentrations lower than 1500 mg L(-1). Chromate reduction activity of whole cells was detected in five isolates. Most of these isolates belong to the genus Bacillus as identified by the 16S rRNA gene sequencing. Maximal Cr(VI) reduction was observed at the optimum pH (7.0-9.0) and temperature (30 degrees C) of growth. One bacterial isolate (Bacillus sp. ES 29) was able to aerobically reduce 90% of Cr(VI) in six hours. The Cr(VI) reduction activity of the whole cells of five isolates had a K(M) of 0.271 (2.61 mM) to 1.51 mg L(-1) (14.50 mM) and a V(max) of 88.4 (14.17 nmol min(-1)) to 489 mg L9-1) h(-1) (78.36 nmol min(-1)). Our consortia and monocultures of these isolates can be useful for Cr(VI) detoxification at low and high concentrations in Cr(VI)-contaminated environments and under a wide range of environmental conditions.     

Light-catalyzed chromium(VI) reduction by organic compounds and soil minerals

Detoxification of Cr(VI) through reduction has been considered an effective method for reclaiming Cr-contaminated soil, sediment, and waste water. Organic matter is widely distributed in soil and aquatic systems; however, low Cr(VI) reduction rates inhibit the adoption of Cr reduction technologies by industry. Scientists have been aware of Cr(VI) reduction catalyzed by soil minerals; however, most of the studies focused on using semiconductors as catalysts with UV irradiation to accelerate the redox reactions. The objective of this study was to evaluate the rates of Cr(VI) reduction by fluorescence light in the presence of organic materials with or without specific soil minerals. Experimental results showed that dissolved organic compounds reduced Cr(VI) slowly under laboratory light; however, Cr(VI) reduction was greatly enhanced when growth chamber light was applied. Low photon flux (i.e., laboratory light) only enhanced Cr(VI) reduction by organics when Fe(III) was also present, because the Fe(II)-Fe(III) redox couple accelerated electron transfer and decreased electrostatic repulsion between reactants. Laboratory light was required to initiate Cr(VI) reduction catalyzed by TiO2; nonetheless, light-catalyzed Cr(VI) reduction by smectite and ferrihydrite could occur only when greater light energy was provided with a growth chamber light. Our results suggest a potential pathway for Cr(VI) reduction using naturally occurring organic compounds and colloids in acidic water systems or in surface soils when light is available.     

In situ reduction of chromium(VI) in heavily contaminated soils through organic carbon amendment

Chromium has become an important soil contaminant at many sites, and facilitating in situ reduction of toxic Cr(VI) to nontoxic Cr(III) is becoming an attractive remediation strategy. Acceleration of Cr(VI) reduction in soils by addition of organic carbon was tested in columns pretreated with solutions containing 1000 and 10 000 mg L(-1) Cr(VI) to evaluate potential in situ remediation of highly contaminated soils. Solutions containing 0,800, or 4000 mg L(-1) organic carbon in the form of tryptic soy broth or lactate were diffused into the Cr(VI)-contaminated soils. Changes in Cr oxidation state were monitored through periodic micro-XANES analyses of soil columns. Effective first-order reduction rate constants ranged from 1.4 x 10(-8) to 1.5 x 10(-7) s(-1), with higher values obtained for lower levels of initial Cr(VI) and higher levels of organic carbon. Comparisons with sterile soils showed that microbially dependent processes were largely responsible for Cr(VI) reduction, except in the soils initially exposed to 10 000 mg L(-1) Cr(VI) solutions that receive little (800 mg L(-1)) or no organic carbon. However, the microbial populations (< or = 2.1 x 10(5) g(-1)) in the viable soils are probably too low for direct enzymatic Cr(VI) reduction to be important. Thus, synergistic effects sustained in whole soil systems may have accounted for most of the observed reduction. These results show that acceleration of in situ Cr(VI) reduction with addition of organic carbon is possible in even heavily contaminated soils and suggest that microbially dependent reduction pathways can be dominant.     

Removal of Cr(VI) from Cr-contaminated groundwater through electrochemical addition of Fe(II)

The conventional chemical reduction-precipitation technique in the removal of Cr(VI) from contaminated groundwater involves a two-step process whereby Cr(VI) is first reduced to Cr(III) at an acidic pH by a reducing agent and in a subsequent step, Cr(III) is precipitated as insoluble hydroxide at an alkaline pH. In a variation of this method, Fe(II) is added electrochemically to the Cr(VI) containing water. From a pure iron electrode, Fe(2+) ions are released into the solution and bring forth the reduction of Cr(VI). At the cathode, H(2)O is reduced whereby the OH(-) ions entering the solution keep the pH of the solution in the alkaline range. This latter fact greatly facilitates simultaneous reduction of Cr(VI) to Cr(III) and co-precipitation of hydroxides of trivalent Cr and Fe. On the basis of a set of experimental data, it is shown that this process is both thermodynamically and kinetically efficient, meaning, with the electrochemical method, rapid and nearly complete removal of Cr(VI) from a groundwater source with both high and low levels of Cr-contamination can be achieved. These factors make the electrochemical process superior to the conventional chemical process in remediation of Cr-contaminated groundwater.     

Structure and thermal stability of toxic chromium(VI) species doped onto TiO2 powders through heat treatment

Chromium(VI)-containing sorbents in the form of sludge or solid residue from treatment processes are often landfilled or used as fill materials, therefore the long-term stability of metal binding is important. The reduction of Cr(VI)–Cr(III) through heat treatment may be a useful detoxification method. After heating at 500, 900, 1000, and 1100 °C for 4 h, the transformation of chemical states of chromium on 105 °C-dried, 7.9% Cr(VI)-doped TiO₂ powders was studied on the basis of surface area measurements, scanning electron microscopy (SEM) images, X-ray diffraction (XRD), and extended X-ray absorption fine structure (EXAFS) spectra. It was shown that Cr(VI) was reduced to Cr(III) in the Cr(VI)-doped samples after heating within 500–900 °C. The present results also suggested that the chromium octahedral was bridged to the titanium tetrahedral and was incorporated in TiO₂ minerals formed after 1000 °C treatment.     

Effects of organic amendments on the reduction and phytoavailability of chromate in mineral soil

In this study, seven organic amendments (biosolid compost, farm yard manure, fish manure, horse manure, spent mushroom, pig manure, and poultry manure) were investigated for their effects on the reduction of hexavalent chromium [chromate, Cr(VI)] in a mineral soil (Manawatu sandy soil) low in organic matter content. Addition of organic amendments enhanced the rate of reduction of Cr(VI) to Cr(III) in the soil. At the same level of total organic carbon addition, there was a significant difference in the extent of Cr(VI) reduction among the soils treated with organic amendments. There was, however, a significant positive linear relationship between the extent of Cr(VI) reduction and the amount of dissolved organic carbon in the soil. The effect of biosolid compost on the uptake of Cr(VI) from the soil, treated with various levels of Cr(VI) (0-1200 mg Cr kg(-1) soil), was examined with mustard (Brassica juncea L.) plants. Increasing addition of Cr(VI) increased Cr concentration in plants, resulting in decreased plant growth (i.e., phytotoxicity). Addition of the biosolid compost was effective in reducing the phytotoxicity of Cr(VI). The redistribution of Cr(VI) in various soil components was evaluated by a sequential fractionation scheme. In the unamended soil, the concentration of Cr was higher in the organic-bound, oxide-bound, and residual fractions than in the soluble and exchangeable fractions. Addition of organic amendments also decreased the concentration of the soluble and exchangeable fractions but especially increased the organic-bound fraction in soil.     

Soil,water and plants contamination by total chrome and chrome VI

The chrome (Cr) is a metal utilized in various industrial sectors and its investigation in the environment is necessary, for the Cr (III) contain aessential micronutrients in the human nourishment and the Cr (VI), on the other hand, is toxic. In the present work soil contamination with Cr was realized in drainagelysimetersset in concentrations of 0, 200, 400, 600, 800 and 1000 mg kg⁻¹ of total Cr, with the intuition to determine the total Cr and Cr (VI) flux in leached water, in soil and in plants of lettuce (Lactuca sativa L.). In the lysimeters were cultivated four plants, in three cultivation circles. In the end of the cultivations was observed, that the total applied Cr leached in the soil, evidencing the Cr mobility in latossoil with simulant characteristics to the ones utilized in this paper. The Cr (VI) concentrations in the soil increased soon after the treatment applications, but tend to decrees in the time elapse, the same tendences were observed for the total Cr concentrations in the leached water. The Cr absorption by plants was related to the Cr disponibility in the soil, for the soil concentration and the plants decreased with time passing. The Cr mobility in the soil possibilitated the groundwater contamination presenting risks to the water quality and, consequently to public health.     

Low-temperature chromium(VI) biotransformation in soil with varying electron acceptors

Effective and low-cost strategies for remediating chromium (Cr)-contaminated soil are needed. Chromium(VI) leaching from contaminated soil into ground water and surface water threatens water supplies and the environment. This study tested indigenous Cr(VI) microbial transformation in batch systems at 10 degrees C in the presence of various electron acceptors. The effects of carbon addition, spiked Cr(VI), and mixing highly contaminated soil with less contaminated soil were investigated. The results indicated that Cr(VI) can be biotransformed in the presence of different electron acceptors including oxygen, nitrate, sulfate, and iron. Sugar addition had the greatest effect on enhancing Cr(VI) removal. Less dissolved organic carbon (DOC) was consumed per amount of Cr(VI) transformed under anaerobic conditions [0.8-93 mg DOC/mg Cr(VI)] compared with aerobic conditions [1.4-265 mg DOC/mg Cr(VI)]. Toxicity of high concentrations (< 160 mg/L) of spiked Cr(VI) were not evident. At Cr(VI) concentrations > 40 mg/L, aerobic conditions promoted faster Cr(VI) reduction than anaerobic conditions with nitrate or sulfate present. Biotransformation of Cr(VI) in highly contaminated soil (22,000 mg Cr/kg) was facilitated by mixing with less-contaminated soil. The study results provide a framework for evaluating indigenous Cr(VI) microbial transformation and enhance the ability to develop strategies for soil treatment.     

The influence of biochar and black carbon on reduction and bioavailability of chromate in soils

The widespread use of chromium (Cr) has a deleterious impact on the environment. A number of pathways, both biotic and abiotic in character, determine the fate and speciation of Cr in soils. Chromium exists in two predominant species in the environment: trivalent [(Cr(III)] and hexavalent [Cr(VI)]. Of these two forms, Cr(III) is nontoxic and is strongly bound to soil particles, whereas Cr(VI) is more toxic and soluble and readily leaches into groundwater. The toxicity of Cr(VI) can be mitigated by reducing it to Cr(III) species. The objective of this study was to examine the effect of organic carbon sources on the reduction, microbial respiration, and phytoavailability of Cr(VI) in soils. Organic carbon sources, such as black carbon (BC) and biochar, were tested for their potential in reducing Cr(VI) in acidic and alkaline contaminated soils. An alkaline soil was selected to monitor the phytotoxicity of Cr(VI) in sunflower plant. Our results showed that using BC resulted in greater reduction of Cr(VI) in soils compared with biochar. This is attributed to the differences in dissolved organic carbon and functional groups that provide electrons for the reduction of Cr(VI). When increasing levels of Cr were added to soils, both microbial respiration and plant growth decreased. The application of BC was more effective than biochar in increasing the microbial population and in mitigating the phytotoxicity of Cr(VI). The net benefit of BC emerged as an increase in plant biomass and a decrease in Cr concentration in plant tissue. Consequently, it was concluded that BC is a potential reducing amendment in mitigating Cr(VI) toxicity in soil and plants.     

Genotypic Variation in the Phytoremediation Potential of Indian Mustard for Chromium

The term “phytoremediation” is used to describe the cleanup of heavy metals from contaminated sites by plants. This study demonstrates phytoremediation potential of Indian mustard (Brasicca juncea (L.) Czern. & Coss.) genotypes for chromium (Cr). Seedlings of 10 genotypes were grown hydroponically in artificially contaminated water over a range of environmentally relevant concentrations of Cr (VI), and the responses of genotypes in the presence of Cr, with reference to Cr accumulation, its phytotoxity and anti-oxidative system were investigated. The Cr accumulation potential varied largely among Indian mustard genotypes. At 100 μM Cr treatment, Pusa Jai Kisan accumulated the maximum amount of Cr (1680 μg Cr g⁻¹ DW) whereas Vardhan accumulated the minimum (107 μg Cr g⁻¹ DW). As the tolerance of metals is a key plant characteristic required for phytoremediation purpose, effects of various levels of Cr on biomass were evaluated as the gross effect. The extent of oxidative stress caused by Cr stress was measured as rate of lipid peroxidation. The level of thiobarbituric acid reactive substances (TBARS) was enhanced at all Cr treatments when compared to the control. Inductions of enzymatic and nonenzymatic antioxidants were monitored as metal-detoxifying responses. All the genotypes responded to Cr-induced oxidative stress by modulating nonenzymatic antioxidants [glutathione (GSH) and ascorbate (Asc)] and enzymatic antioxidants [superoxide dismutase (SOD), ascorbate peroxidase (APX), and glutathione reductase (GR)]. The level of induction, however, differed among the genotypes, being at its maximum in Pusa Jai Kisan and its minimum in Vardhan. Pusa Jai Kisan was grown under natural field conditions with various Cr treatments, and Cr-accumulation capacity was studied. The results confirmed that Pusa Jai Kisan is a hyperaccumulator of Cr and hypertolerant to Cr-induced stress, which makes this genotype a viable candidate for use in the development of phytoremediation technology of Cr-contaminated sites.     

A methodology to estimate the denitrifying capacity of a riparian wetland

Numerous studies have shown that riparian wetlands can play an important role in reducing nitrate concentrations before the ground water discharges into streams. Denitrification has been identified as an important process for this removal. Several approaches have been proposed to predict the denitrifying removal capacity of a riparian wetland, but no widely used tool exists to precisely quantify this capacity at the landscape scale. We propose such a methodology based on modeling the spatial variation of soil-water interactions in the entire riparian wetland. Mean values of denitrification enzyme activity (DEA) within three soil-denitrifying classes were 604, 212, and 24 ng N g(-1) h(-1) for Classes 3, 2, and 1, respectively. The study area, having a ground surface of about 15000 m2, was underlain by an aquifer with a calculated volume of 60000 m3, less than 10000 m3 of which corresponded to active denitrifying horizons (Classes 2 and 3). By volume, approximately 30% of Class 3 and 70% of Class 2 were interacting with ground water. The denitrifying removal capacity of our wetland was calculated to be about 1.8 kg N m(-2) yr(-1). The calculated denitrifying capacity of our site was less than expected. This is due to the fact that not all ground water interacts with the horizons having the highest denitrifying capacity. Thus, we show that whatever the system is, specific local pedological and hydrogeological conditions and their interactions are paramount in controlling the denitrification process.     

Soil microbial community response to hexavalent chromium in planted and unplanted soil

Theories suggest that rapid microbial growth rates lead to quicker development of metal resistance. We tested these theories by adding hexavalent chromium [Cr(VI)] to soil, sowing Indian mustard (Brassica juncea), and comparing rhizosphere and bulk soil microbial community responses. Four weeks after the initial Cr(VI) application we measured Cr concentration, microbial biomass by fumigation extraction and soil extract ATP, tolerance to Cr and growth rates with tritiated thymidine incorporation, and performed community substrate use analysis with BIOLOG GN plates. Exchangeable Cr(VI) levels were very low, and therefore we assumed the Cr(VI) impact was transient. Microbial biomass was reduced by Cr(VI) addition. Microbial tolerance to Cr(VI) tended to be higher in the Cr-treated rhizosphere soil relative to the non-treated systems, while microorganisms in the Cr-treated bulk soil were less sensitive to Cr(VI) than microorganisms in the non-treated bulk soil. Microbial diversity as measured by population evenness increased with Cr(VI) addition based on a Gini coefficient derived from BIOLOG substrate use patterns. Principal component analysis revealed separation between Cr(VI) treatments, and between rhizosphere and bulk soil treatments. We hypothesize that because of Cr(VI) addition there was indirect selection for fast-growing organisms, alleviation of competition among microbial communities, and increase in Cr tolerance in the rhizosphere due to the faster turnover rates in that environment.     

Removal of selenate from water by zerovalent iron

Zerovalent iron (ZVI) has been widely used in the removal of environmental contaminants from water. In this study, ZVI was used to remove selenate [Se(VI)] at a level of 1000 microg L(-1) in the presence of varying concentrations of Cl-, SO(2-)4, NO(-)3, HCO(-)3, and PO(3-)4. Results showed that Se(VI) was rapidly removed during the corrosion of ZVI to iron oxyhydroxides (Fe(OH)). During the 16 h of the experiments, 100 and 56% of the added Se(VI) was removed in 10 mM Cl- and SO(2-)4 solutions under a closed contained system, respectively. Under an open condition, 100 and 93% of the added Se(VI) were removed in the Cl- and SO(2-)4 solutions, respectively. Analysis of Se species in ZVI-Fe(OH) revealed that selenite [Se(IV)] and nonextractable Se increased during the first 2 to 4 h of reaction, with a decrease of Se(VI) in the Cl- experiment and no detection of Se(VI) in the SO(2-)4 experiment. Two mechanisms can be attributed to the rapid removal of Se(VI) from the solutions. One is the reduction of Se(VI) to Se(IV), followed by rapid adsorption of Se(IV) to Fe(OH). The other is the adsorption of Se(VI) directly to Fe(OH), followed by its reduction to Se(IV). The results also show that there was little effect on Se(VI) removal in the presence of Cl- (5, 50, and 100 mM), NO(-)3 (1, 5, and 10 mM), SO(2-)4 (5 mM), HCO(-)3 (1 and 5 mM), or PO(3-)4 (1 mM) and only a slight effect in the presence of SO(2-)4 (50 and 100 mM), HCO(-)3 (10 mM), and PO(3-)4 (5 mM) during a 2-d experiment, whereas 10 mM PO(3-)4 significantly inhibited Se(VI) removal. This work suggests that ZVI may be an effective agent to remove Se from Se-contaminated agricultural drainage water.     

Removal of chromium(VI) from electroplating industry wastewater using bagasse fly ash—a sugar industry waste material

A waste product generated in the sugar industry in India has been converted into a cheap potential adsorbent. This has been characterised and utilized for the removal of chromium (VI) from synthetic and actual wastewater. The sorption efficiency decreases with increase in pH. Adsorption of Cr (VI) on bagasse fly ash follows the Freundlich and Langmuir isotherms and these have been used to obtain the thermodynamic parameters of the process. The sorption capacity of this adsorbent for chromium removal is found to be comparable to other low cost adsorbents.