Vacuum pyrolysis of waste tires with basic additives

Granules of waste tires were pyrolyzed under vacuum (3.5-10kPa) conditions, and the effects of temperature and basic additives (Na(2)CO(3), NaOH) on the properties of pyrolysis were thoroughly investigated. It was obvious that with or without basic additives, pyrolysis oil yield increased gradually to a maximum and subsequently decreased with a temperature increase from 450 degrees C to 600 degrees C, irrespective of the addition of basic additives to the reactor. The addition of NaOH facilitated pyrolysis dramatically, as a maximal pyrolysis oil yield of about 48wt% was achieved at 550 degrees C without the addition of basic additives, while a maximal pyrolysis oil yield of about 50wt% was achieved at 480 degrees C by adding 3wt% (w/w, powder/waste tire granules) of NaOH powder. The composition analysis of pyrolytic naphtha (i.b.p. (initial boiling point) approximately 205 degrees C) distilled from pyrolysis oil showed that more dl-limonene was obtained with basic additives and the maximal content of dl-limonene in pyrolysis oil was 12.39wt%, which is a valuable and widely-used fine chemical. However, no improvement in pyrolysis was observed with Na(2)CO(3) addition. Pyrolysis gas was mainly composed of H(2), CO, CH(4), CO(2), C(2)H(4) and C(2)H(6). Pyrolytic char had a surface area comparable to commercial carbon black, but its proportion of ash (above 11.5wt%) was much higher.     

Reaction Kinetic Model For Optimal Pyrolysis Of Plastic Waste Mixtures

Reaction kinetics at various temperatures for pyrolysis of mixtures of plastic waste [polyethylene(PE) and polystyrene(PS)] are modelled in terms of five types of pyrolysis reaction. The model development is based on the assumption that as plastic wastes are heated in a non-reactive environment they are decomposed homogeneously to various products of gas, oil and char by a first-order rate, irreversible reaction and isothermal condition. Among the five models, the type II model in which the activated polymer exists as an intermediate product is the most accurate in predicting the pyrolysis products of pure PE or pure PS. Also, for mixtures of plastics both type II and IV models can be used to explain the composition of pyrolysis products. Furthermore, from the analysis of variance (ANOVA), the mixing ratio and temperature are shown to be the parameters that have the greatest effect on the pyrolysis reaction of polymer waste mixture. The pyrolysis reaction time for the maximum oil production from PE-PS mixtures is shorter than for PE alone and approaches that of PS alone. Oil production increases with increase of PS content. The optimal temperature for maximum oil production is 600°C for the pyrolysis of 2:8, 5:5 and 1:0 mixtures (w/w) of PE and PS. Oil production for PS alone is constant when the pyrolysis is above 600°C.     

Investigation on thermal dechlorination and catalytic pyrolysis in a continuous process for liquid fuel recovery from mixed plastic wastes

A continuous system (feeding rate >1 kg/h) consisting of thermal dechlorination pre-treatment and catalytic pyrolysis with Fe-restructured clay (Fe-RC) catalyst was developed for feedstock recycling of PVC-containing mixed plastic waste. The vented screw conveyor which was specially designed for continuous dechlorination was able to achieve dechlorination efficiency of over 90 % with a feedstock retention time longer than 35.5 min. The chlorine content of the pyrolytic oil obtained after dechlorination was in the range of 6.08–39.50 ppm, which meet the specification for reclamation pyrolytic oil in Japan. Fe-RC was found to significantly improve the yield of pyrolytic oil (achieved to 83.73 wt%) at the optimized pyrolysis temperature of 450 °C and catalyst dosage of 60 g. With the optimized parameters, Fe-RC showed high selectivity for the C₉–C₁₂ and C₁₃–C₁₉ oil fraction, which are the major constituents of kerosene and diesel fuel, demonstrating that this catalyst can be applied in the pyrolysis of mixed plastic wastes for the production of kerosene and diesel fuel. Overall, the continuous process exhibited high stability and consistently high-oil yield upon reaching steady state, indicating its potential up-scaling application in the industry.     

用废旧电路板热解油制备酚醛树脂

在碳酸钙存在下,采用热解技术将废旧电路板中的树脂转化为富含酚的热解油,然后直接加入甲醛溶液反应制备热解油型酚醛树脂,实现了废旧电路板中树脂的再生,酚醛树脂的性能结构类似于氨催化的酚醛树脂。实验结果表明：在n（甲醛）：n（热解油）为1．8～2．1的条件下,无需外加催化剂,在60,80,90℃下分别反应30min制备的热解油型酚醛树脂的性能最佳,且可满足GB／T14732—93《木材工业胶黏剂用脲醛、酚醛、三氧氰胺甲醛树脂》中层压材料用酚醛树脂产品的相关标准。     

Thermal pyrolysis of fresh and waste fishing nets

Kinetic tests on the pyrolysis of nylon-6 taken from fresh (new) fishing nets and waste fishing nets were conducted using thermogravimetric analysis at heating rates of 0.5, 1.0 and 2.0 degrees C/min. The main region of decomposition of both materials was between 340 and 440 degrees C at each heating rate. The region of decomposition for the nylon-6 from the waste fishing nets was slightly lower than that of the fresh fishing nets. The result shows that the value of activation energies increased from 128 to 433 kJ mol(-1) as the conversion of the pyrolysis reaction increased from 5% to 95%. Nylon-6 from the fresh fishing nets was pyrolyzed in a micro-scale tubing bomb reactor for 60, 80 and 100 min at 440 degrees C. The yield of pyrolyzed gases increased from 3.94 to 5.50 wt% with reaction time. The selectivity to specific hydrocarbons was not detected from the pyrolyzed oil and the carbon number distribution of the pyrolyzed oil was random.     

Influence of pine wood shavings on the pyrolysis of poultry litter

Poultry litter from broilers and turkeys are a mixture of manure, feathers, feed and wood shavings, thus pyrolysis oils produced from this material are influenced by the individual components. In order to determine the influence of wood shavings that are used as bedding material, we investigated the pyrolysis of pine wood shavings and poultry manure. Because manure from layer chickens are usually not contaminated with wood shavings, we made mixtures of layer manure and pine wood shavings in the following manure to wood ratios, 100:0, 75:25, 50:50, 25:75, and 0:100 w/w and pyrolyzed them in a fluidized bed reactor at 450 °C. The total liquid yield ranged from 43.3 to 62.7 wt.%. The layer manure oil had a HHV of 29.7 MJ/kg and pH of 5.89 compared to pine wood oil which had HHV of 25.6 MJ/kg and pH of 3.04. The addition of wood shavings to manure clearly influenced the physical properties of the oil, resulting in a decrease in pH and HHV and an increase in density. The oils had relatively high nitrogen content ranging from 1.36 to 5.88 wt.%. The ash (<0.07 wt.%) and sulfur (<0.28 wt.%) contents were very low. FTIR, ¹³C NMR and ¹H NMR spectrometric analysis of the oils showed that manure oil was rich in hydrocarbons and nitrogenous compounds such as primary, secondary amides, aromatic amines and N-heterocyclic. The properties of the oils were strongly influenced by the amount of wood in the mixture.     

Characteristics of liquid product from the pyrolysis of waste plastic mixture at low and high temperatures: influence of lapse time of reaction

Pyrolysis of a waste plastic mixture (high-density polyethylene: low-density polyethylene: polypropylene: polystyrene = 3:2:3:1) into a liquid product was carried out in a stirred semi-batch reactor at low (350 degrees C) and high (400 degrees C) temperatures. The effect of lapse time of reaction in the reactor and also degradation temperature on the characteristics of the liquid product from pyrolysis of the mixture was investigated. Liquid products were described by cumulative amount distribution, paraffin, olefin, naphthene and aromatic (PONA) distribution and molecular weight distribution. Their characteristic was quite differed with a lapse time of reaction and also at a low and high degradation temperatures, because of the different physicochemical properties of the plastic types in the mixture. With increase of lapse time of reaction, the order for the main products in PONA components obtained at 350 degrees C was firstly aromatic products and then olefin products, while at 400 degrees C the order was firstly aromatic products, then olefin products and finally paraffin products. The experiments also showed from the molecular weight distribution of liquid PONA components that the paraffin and olefin products had a wide distribution by mainly random scission of polymer, but in the case of olefin products were produced by an end-chain scission mechanism as well as random scission mechanism, as evidenced by much more light olefin products. This phenomenon was evident at a higher degradation temperature. Also, both the light olefin and naphthene products with a molecular weight of around 120, as a main product, showed a similar trend as a function of lapse time, which had a maximum fraction at 343 min (at 350 degrees C) and 83 min (at 400 degrees C). Among PONA components, the highest concentrations of aromatic products were obtained with a molecular weight of around 100 at the fastest lapse time of reaction, regardless of degradation temperature. It was concluded that the characteristics of liquid product on the pyrolysis of plastic mixtures were strongly influenced by lapse time of reaction and degradation temperature.     

Pyrolysis kinetics of waste PVC pipe.

The pyrolysis kinetics of waste PVC pipe was investigated with a thermal gravimetric analysis system at heating rates of 5, 10, and 30 degrees C/min in a nitrogen atmosphere. Freeman-Carroll method was employed to evaluate kinetic parameters. Two dominant peaks were observed on derivative gravimetric curves, hypothetically suggesting a two-stage apparent reaction model. The first-stage reaction was likely to be represented by stoichiometric reaction to yield volatiles (mainly HCl) and intermediates. The second-stage reaction might be described by thermal degradation of intermediates competitively into gas, liquid, and solid by-products. Quasi-isothermal operations were introduced to verify the reaction types of the first and second reaction. The generation reaction of intermediates achieved at lower temperatures was carried out independently with their decomposition reaction at higher temperatures. The effects of additives on the pyrolysis kinetics of waste PVC pipe seem to be significant, especially on the first-stage reaction. The first-stage reaction was retarded. A merged peak at low temperatures was observed on the derivative thermogravimetry (DTG) curve instead of two peaks usually observed for that of pure PVC resin. The first peak on the DTG curve of pure PVC resin may shift more, resulting in the complete overlap of two peaks. The quantity of evolved HCl was likely to decrease because of interaction of metal components of stabilizers with either HCl or active chlorine atom or both. The final residual fraction increased as a result of pyrolysis of organic forms of additives to yield extra char. On the other hand, the second-stage reaction kinetics demonstrates a similar pattern to that of pure PVC resin, implying that the effects of additives may be less significant in comparison with that at the first-stage reaction.     

Storage stability of biocrude oils from fast pyrolysis of poultry litter

The unstable nature of biocrude oils produced from conventional pyrolysis of biomass is one of the properties that limits its application. In the disposal of poultry litter via pyrolysis technology, the biocrude oil produced as a value-added product can be used for on farm applications. In this study, we investigated the influence of bedding material (wood shavings) on the storage stability of biocrude oils produced from the fast pyrolysis of poultry litter. The biocrude oils produced from manure, wood (pine and oak), and mixtures of manure and wood in proportions (75:25 50:50, and 25:75 w/w%) were stored under ambient conditions in sealed glass vials for a period of 6 months and their stability were monitored by measuring the changes in viscosity over time. The manure oil had the lowest rate of viscosity change and thus was relatively the most stable and the oils from the 50:50 w/w% litter mixtures were the least stable. The rate of viscosity change of the manure biocrude oil was 1.33 cP/day and that of the 50/50 litter mixture was 7.6 cP/day for pine and 4.17 cP/day for oak.The spectrometric analyses of the biocrude oils showed that the presence of highly reactive oxygenated functionalities in the oil were responsible for the instability characteristic of the litter biocrude oils. The poor stability of the biocrude oil from the 50:50 w/w% litter mixtures was attributed to reactions between nitrogenous compounds (amides) from protein degradation and oxygenated compounds from the decomposition of polysaccharides and lignin. The addition of 10% methanol and 10% ethanol to the oil from 50% manure and 50% pine reduced the initial viscosity of the oil and was also beneficial in slowing down the rate of viscosity change during storage.     

土壤残留塑料的热降解脱附研究

针对土壤的塑料污染问题,提出一种采用热脱附降解技术修复污染土壤的方法.选取4种土壤中常见的残留塑料(聚乙烯(PE)、聚氯乙烯(PVC)、聚对苯二甲酸乙二酯(PET)、聚丙烯(PP))为研究对象,通过控制热解温度和土壤含水率对各污染土壤的修复效果进行探究.实验结果表明:在500℃的最佳热解温度下处理60 min,PE、P...     

Effect of some environmentally degradable materials on the pyrolysis of plastics II: influence of cellulose and lignin on the pyrolysis of complex mixtures

Pyrolysis of polymer mixtures with a composition similar to that of municipal plastic waste containing polyvinyl chloride (PVC) and of municipal plastic waste free of PVC was performed in the presence of components of biomass, namely lignin, cellulose, or both. The pyrolysis products were characterized by standard methods utilized in the petrochemical industry, i.e., paraffins-isoparaffinsolefins-naphthenes-aromatics analysis, proton nuclear magnetic resonance and infrared spectroscopy, and gas chromatography-mass spectrometry. Up to 3 wt% lignin, cellulose, or both in mixed polymers changed the material balance of pyrolysis by decreasing the amount of waxy products. The presence of both PVC and biomass components significantly changed the material balance by decreasing the waxy product yield and increasing the gas and coke yield. The composition of all pyrolysis products was also modified with the addition of PVC, components of biomass, or both.     

TG/FTIR analysis on co-pyrolysis behavior of PE,PVC and PS

The pyrolysis and co-pyrolysis behaviors of polyethylene (PE), polystyrene (PS) and polyvinyl chloride (PVC) under N₂ atmosphere were analyzed by Thermal gravimetric/Fourier transform infrared (TG/FTIR). The volatile products were analyzed to investigate the interaction of the plastic blends during the thermal decomposition process. The TGA results showed that the thermal stability increased followed by PVC, PS and PE. The pyrolysis process of PE was enhanced when mixed with PS. However, PS was postponed when mixed with PVC. As for PE and PVC, mutual block was happened when mixed together. The FTIR results showed that the free radical of the decomposition could combine into a stable compound. When PE mixed with PVC or PS, large amount of unsaturated hydrocarbon groups existed in products while the content of alkynes was decreased. The methyl (CH₃) and methylene (CH₂) bonds were disappeared while PVC mixed with PE.     

Quality improvement of pyrolysis oil from waste rubber by adding sawdust

This work was aimed at improving the pyrolysis oil quality of waste rubber by adding larch sawdust. Using a 1 kg/h stainless pyrolysis reactor, the contents of sawdust in rubber were gradually increased from 0%, 50%, 100% and 200% (wt%) during the pyrolysis process. Using a thermo-gravimetric (TG) analyzer coupled with Fourier transform infrared (FTIR) analysis of evolving products (TG–FTIR), the weight loss characteristics of the heat under different mixtures of sawdust/rubber were observed. Using the pyrolysis–gas chromatography (GC)–mass spectrometry (Py–GC/MS), the vapors from the pyrolysis processes were collected and the compositions of the vapors were examined. During the pyrolysis process, the recovery of the pyrolysis gas and its composition were measured in-situ at a reaction temperature of 450 °C and a retaining time of 1.2 s. The results indicated that the efficiency of pyrolysis was increased and the residual carbon was reduced as the percentage of sawdust increased. The adding of sawdust significantly improved the pyrolysis oil quality by reducing the polycyclic aromatic hydrocarbons (PAHs) and nitrogen and sulfur compounds contents, resulting in an improvement in the combustion efficiency of the pyrolysis oil.     

超声波协同催化氧化法脱除废旧轮胎热裂解油中的硫

采用超声波氧化与催化氧化脱硫技术相结合,脱除废旧轮胎热裂解油中的硫,对脱硫工艺进行了研究.最佳操作条件为:超声波声强0.25 W/cm~2,超声时间10 min,V(H_2O_2)∶V(油)=0.04,V(CH_3COOH)∶V(H_2O_2)＝0.5,V(FeSO_4·7H_2O) ∶ V(H_2O_2)＝0.15.在上述最佳操作条件下,进行4次脱硫,可使热裂解油中硫质量分数降至0.21%,脱硫率达到72%.     

我国废塑料油化技术的应用现状与前景

介绍了我国废塑料油化技术的现状,对废塑料的热解法、热解－催化改质法、催化热解法3种基本方法进行了经济技术评价,对建立废塑料油化工厂的原料收集体系及运输距离、建厂规模、生产过程中存在的二次污染问题进行了分析,探讨了控制污染的方案,对制定相关的政策和法律提出了建议,探讨了具有我国特色的废塑料油化技术发展及应用之路。     

Pyrolysis of latex gloves in the presence of Y-zeolite

In this study we have investigated the possibility of processing waste rubber gloves using pyrolysis. Y-zeolite catalyst was employed to upgrade the pyrolysis products to give higher yields of valuable aromatic compounds such as toluene and xylenes. The composition of the pyrolysis products was determined using gas chromatography with linked mass spectrometry (GC-MS), gas chromatograph equipped with a flame ionization detector (GC-FID), gas chromatograph fitted with dual thermal conductivity detectors (GC-TCD), and Fourier Transform Infra-Red Spectrometry (FT-IR). It was found that when rubber gloves were pyrolysed in the absence of a catalyst, the pyrolysis oil consisted mainly of limonene and oligomers of polyisoprene. When Y-zeolite was added to the reaction system, the yields of toluene, xylene, methylbenzenes, ethylbenzenes, and naphthalenes increased dramatically. The Y-zeolite also catalysed the decomposition of limonene, which was absent from the catalytic pyrolysis products. The presence of the Y-zeolite catalyst also increased the yield of hydrocarbon gases. The tests were carried out at both 380 degrees C and 480 degrees C and it was found that the higher reaction temperature led to increased yields of all the major compounds, both in the presence and absence of the Y-zeolite catalyst.     

Pyrolysis characteristics and kinetics of chicken litter

Chicken litter generally consists of a mixture of bedding, manure, feathers and spilled food. Flock of birds litter (flock) is a litter consisting of hardwood shavings, feed, feathers and manure; and broiler litter (broiler) is a cake of chicken litter. A kinetic investigation of the pyrolysis of chicken litter (flock and broiler) was carried out using thermogravimetric analysis (TGA) at heating rates of 5 degrees C/min, 10 degrees C/min and 20 degrees C/min. Most of the materials decomposed between 270 degrees C and 590 degrees C at each heating rate. The region of decomposition of flock and broiler was slightly lower than that of the wood chips. Wood chips (bedding material) decomposed in two stages, while flock and broiler decomposed in three stages. Apparent activation energies increased from 99 to 484 kJ/mol for the three samples when the pyrolytic conversion increased from 5% to 95%.     

Comparative analysis for the production of fatty acid alkyl esterase using whole cell biocatalyst and purified enzyme from Rhizopus oryzae on waste cooking oil (sunflower oil)

The petroleum fuel is nearing the line of extinction. Recent research and technology have provided promising outcomes to rely on biodiesel as the alternative and conventional source of fuel. The use of renewable source - vegetable oil constitutes the main stream of research. In this preliminary study, Waste Cooking Oil (WCO) was used as the substrate for biodiesel production. Lipase enzyme producing fungi Rhizopus oryzae 262 and commercially available pure lipase enzyme were used for comparative study in the production of Fatty Acid Alkyl Esters (FAAE). The whole cell (RO 262) and pure lipase enzyme (PE) were immobilized using calcium alginate beads. Calcium alginate was prepared by optimizing with different molar ratios of calcium chloride and different per cent sodium alginate. Entrapment immobilization was done for whole cell biocatalyst (WCB). PE was also immobilized by entrapment for the transesterification reaction. Seven different solvents - methanol, ethanol, n-propanol, n-butanol, iso-propanol, iso-butanol and iso-amyl alcohol were used as the acyl acceptors. The reaction parameters like temperature (30°C), molar ratio (1:3 - oil:solvent), reaction time (24 h), and amount of enzyme (10% mass ratio to oil) were also optimized for methanol alone. The same parameters were adopted for the other acyl acceptors too. Among the different acyl acceptors - methanol, whose reaction parameters were optimized showed maximum conversion of triglycerides to FAAE-94% with PE and 84% with WCB. On the whole, PE showed better catalytic converting ability with all the acyl acceptor compared to WCB. Gas chromatography analysis (GC) was done to determine the fatty acid composition of WCO (sunflower oil) and FAAE production with different acyl acceptors.     

Kinetics of thermal de-chlorination of PVC under pyrolytic conditions

Although PVC-containing wastes are an important potential source of energy they are frequently disposed in landfill. In thermal treatment processes such as pyrolysis and gasification, the presence of poly(vinyl chloride) (PVC), a compound with 56.7% of chlorine, may cause problems concerned with environmental protection, as consequence of the formation of hydrochloric acid, chlorine gas and dioxins, as well as corrosion phenomena of the reactor/equipment materials. Thus, a possible solution may involve a previous removal of the chlorine from PVC containing waste through a pyrolysis process at low temperatures before the material being submitted to a subsequent thermal treatment, for energetic valorization. In this work, a kinetic model for the thermal decomposition of PVC has been developed, in view of its de-chlorination. DTA/TGA testing at different temperatures indicated a first order reaction and an activation energy of 133,800J/mol. An almost completed de-chlorination reaction was obtained at 340°C under an inert atmosphere. The resulted material is a C(n)H(n) type polymer with potential to be used in an energy recovery process. Validation test performed at laboratory scale indicate that the temperature of 340°C enables the removal of ～99.9% of the chlorine present in PVC. The chloride can be fixed in the form of an aqueous solution of HCl or calcium chloride, driving to an alternative full process with environmental benefits and reduction of the costs associated to the PCV - containing materials/wastes management.     

Influence of dairy manure addition on the biological and thermal kinetics of composting of greenhouse tomato plant residues

A laboratory-scale bioreactor was used to investigate the influence of dairy manure addition (as an inoculum and a carbon source) on the biological and thermal kinetics of the composting process of tomato plant residues-wood shavings mixture. Urea was added (as a nitrogen source) to correct the initial C:N ratio to 30:1 and the initial moisture content was also adjusted to 60%. The result of this study indicated that manure addition to the tomato residues-wood shavings mixture is a good source of macro and micronutrients required for supporting the composting microorganisms. Manure addition increased the rate of temperature increase and the duration of maximum temperature and reduced the lag and the peak time, all of which resulted in a significant reduction in the retention time. However, thermophilic temperature (> or = 40 degrees Celsius) was only achieved with 30%, 40% and 50% manure addition for 3, 7 and 9h. Total carbon reductions were in the range of 9.4-10.8% and TKN reductions were in the range of 3.4-6.0%. Neither the nitrogen nor the moisture content were limiting factors as the C:N ratio remained in the range of 26:1 to 28:1 and the moisture content remained within the optimum range of 58-61%. The maximum temperature of each mixture correlated with the reduction of total carbon, but carbon availability was a limiting factor in these experiments. In order to attain and sustain a thermophilic phase during the composting process, the addition of a readily available carbon source to the tomato should be investigated and carbon type (carbohydrates, proteins and fats) should be taken into account.