首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 546 毫秒
1.
采用介质阻挡放电低温氧等离子体技术进行表面改性的活性碳纤维(ACFP)为载体,进行CeO2/ACFP催化剂低温选择性催化还原(SCR)NO的研究。实验结果表明,ACF先经过低温氧等离子体技术进行表面改性后再负载CeO2,能明显提高对NO的去除率。在NO体积分数为1×10^-3、NH3体积分数为2×10^-3、O2体积分数为5%、Ar作为平衡气、反应温度为120—240℃的条件下,较理想的CeO2负载量(质量分数)为9%;在180℃用9%CeO2/ACFP为催化剂时,NO去除率为86.01%。  相似文献   

2.
BaO/γ-Al2O3同时吸附脱除一氧化氮和二氧化硫   总被引:1,自引:0,他引:1  
利用固定床连续流动反应器研究了BaO/γ—Al2O,同时吸附模拟烟气中NO和SO2的工艺条件和再生循环使用性能,对BaO/γ—Al2O3进行了比表面积和程序升温表面反应(TPSR)等表征分析。结果表明,BaO/γ—Al2O3的适宜工艺条件是SO2与NO体积比为2.9~8.4、原料气中O2体积分数大于4.5%、吸附温度448~523K。BaO/γ—Al2O3在循环使用过程中吸附能力下降。与NOXSO吸附催化剂Na2CO3/γ—Al2O3相比,BaO/γ-Al2O3同时吸附SO2和NO的能力大、再生循环使用性能好、适宜的SO2与NO体积比范围宽、热稳定性好。将BaO/γ—Al2O3应用于NOXSO工艺可望提高该工艺的脱硫、脱氮效率。  相似文献   

3.
生物质吸附剂处理活性艳红X-3B废水   总被引:2,自引:0,他引:2  
采用城市污水处理厂二沉池的剩余活性污泥为原料,以浓度为3mol/L的ZnCl2溶液浸泡污泥,采用水蒸气为活化气和保护气,在600℃下活化污泥3h,制备出性能良好的生物质吸附剂,其碘吸附值为388.95mg/g,比表面积为447.79m^2/g,平均孔径为4.39nm,孔体积为0.31cm^3/g,微孔体积为0.09cm^3/g。实验结果表明,用该生物质吸附剂处理活性艳红X-3B废水,在废水(10mL)中活性艳红X-3B质量浓度为300mg/L、生物质吸附剂加入量为0.20g、吸附时间为30min的条件下,废水脱色率可达99.7%。活性艳红X-3B在生物质吸附剂上的吸附行为遵循Lagergren二级动力学规律,同时也可用一级吸附动力学方程描述。  相似文献   

4.
Bi2WO6催化剂的合成和表征及其光催化活性   总被引:1,自引:1,他引:0  
以Bi(NO3)3和Na2WO4为原料,采用水热法合成了可见光催化剂Bi2WO6,并采用X射线衍射仪和BET法对其进行了表征。考察了合成温度、Bi2WO6加入量、邻氯苯酚(2-CP)浓度、溶液pH等对2-CP光催化降解效果的影响。实验结果表明:在加入140℃下合成的Bi2WO6催化剂1g/L、原始pH(pH=5.85)、可见光光照210min的条件下,对质量浓度为20mg/L的2-CP溶液进行处理,2-CP去除率最高为97.2%;添加少量H2O2对2-CP的降解有促进作用。  相似文献   

5.
过氧化钙的制备及其在废水处理中的应用   总被引:4,自引:0,他引:4  
开发出一种过氧化钙常温合成新工艺。在氯化铵与过氧化氢质量比为10/130、采用稳定剂ⅠA和稳定剂ⅡB的条件下,使氢氧化钙与过氧化氢反应合成过氧化钙,其收率为35.9%,纯度为72.3%。用制得的过氧化钙去除机械工业废水中的重金属离子,在室温、过氧化钙用量0.1%~0.2%、处理时间30min、处理过程中不调整pH的条件下,含锰35.58μg/mL、铜67μg/mL、锌31.3μg/mL、铬43.56μg/mL(均为质量浓度)的废水经一次处理后,锰、铜、锌浓度和pH均达到国家一级水排放标准,铬的一次去除率达到39%以上。  相似文献   

6.
固相萃取-气相色谱法检测水中的邻苯二甲酸酯   总被引:7,自引:0,他引:7  
利用固相萃取技术富集了水中4种邻苯二甲酸酯类(PAEs)化合物:邻苯二甲酸二甲酯(DMP)、邻苯二甲酸二乙酯(DEP)、邻苯二甲酸二丁酯(DBP)、邻苯二甲酸二(2-乙基己基)酯(DEHP)。借助均匀设计法及计算机回归建模优化技术对4种PAEs的固相萃取条件进行了设计与优化,得到的最佳固相萃取条件:洗脱剂配比(正己烷与丙酮的体积比)30:1,洗脱体积2mL,洗脱速率4mL/min,上样速率8mL/min。富集后的试样用带电子捕获器的毛细管气相色谱仪检测,方法的线性范围为1~1000μg/L(DMP,DEP),0.2—100μg/L(DBP,DEHP),线性回归方程的相关系数为0.9970~1.0000,检出限为0.02-0.4μg/L,4种PAEs的回收率为69%~117%,相对标准偏差为2.5%~9.5%。[关键词]  相似文献   

7.
污泥活性炭的制备及其对溶液中Cr6+的吸附   总被引:6,自引:2,他引:4  
以城市污水厂剩余污泥为原料,采用ZnCl2作活化剂,热解制备污泥活性炭。实验结果表明,制备污泥活性炭的最佳条件热解温度为550℃,ZnCl2溶液浓度为3mol/L,ZnCl2溶液体积与污泥质量比(mL/g)为2.5:1,热解时间为25min。用所制备的污泥活性炭吸附溶液中的Cr6+最佳吸附条件为:吸附时间90min,Cr6+初始质量浓度50mg/L,污泥活性炭加入量0.2g,溶液pH2,在此条件下,Cr6+去除率达99.9%。污泥活性炭对溶液中Cr6+的吸附等温线属于I型,等温吸附方程可用Langmuir模型和Freundlich模型来拟合。  相似文献   

8.
以盐泥为原料,采用氯化铵浸取回收盐泥中的Mg2+,以浸取液和回收的氨反应制取氢氧化镁产品。考察了盐泥浆液固含量、浸取时间、物料比(氯化铵与盐泥中氢氧化镁的摩尔比)等工艺条件对Mg2+浸取率的影响,并以比表面积为考察指标进行正交实验,确定氢氧化镁的最佳制备条件。实验结果表明:在盐泥浆液固含量为248 g/L、浸取时间为100 min、物料比为2.3的条件下,Mg2+浸取率为75.0%;在n(MgCl2):n(NH4Cl)=0.5、氨水浓度3 mol/L、氨水滴加速率 0.8 mL/min、反应温度 90 ℃的最佳条件下,制备的氢氧化镁的比表面积为17.87 m2/g,粒径约为3 μm。该工艺简单可行,为盐泥的综合利用提供了新的思路。  相似文献   

9.
二甲基二硫醚废气的处理   总被引:1,自引:0,他引:1  
钱玲  张所信 《化工环保》2003,23(1):32-35
研究了二甲基二硫醚(DMDS)废气的处理技术,先将废气冷凝成废液,废液经蒸馏回收二甲基二硫醚,利用双氧水将废残液中二甲基硫醚(DMS)氧化为二甲基亚砜(DMSO),考察了反应溶剂及其用量,反应温度、原料配比、双氧水滴加速度等反应的影响。确定的适宜工艺条件:以丙酮为溶剂,二甲基硫醚,双氧水,丙酮的体积配比为0.75:1:1,双氧水的流量为2.0mL/min,反应时间为3.0-3.5h,反应温度为20-30℃,在此工艺条件下二甲基亚砜的产率为90.7%。  相似文献   

10.
硫酸生产中废钒催化剂回收工艺研究   总被引:2,自引:0,他引:2  
采用H2SO4浸取、NH4HSO3还原、NH4NO3氧化、KOH精制的方法回收废钒催化剂中的V2O5。实验结果表明,还原反应的最佳条件为:n(NH4HSO3)/n(V2O5)=1.10,还原反应温度90℃,还原反应时间2.0h。氧化反应的最佳条件为:n(KOH)/n(VO^+)=1.10,氧化反应温度60℃,液固比8,氧化反应时间60min。该方法V2O5回收率达90.3%以上,V2O5纯度达82%以上。  相似文献   

11.
Concentrations and total quantity of cadmium (Cd), cupper (Cu),lead (Pb) and zink (Zn) were determined in biomass and soil compartments in a replicated tree species experiment with 27-yr-old stands growing on former farmland in N.E. Sweden. Sequentialextractions of soil samples were performed in order to estimate the exchangeable and an organically bound fraction of each element. The tree species included were Picea abies (L.)H. Karst., Pinus sylvestris L., Pinus contorta Dougl., Larix sibirica Ledeb., and Betula pendula Roth.Tree species influenced the rate of removal of Cu, Pb and Zn incase of stemwood harvesting, and of Cd, Cu and Zn in the case ofwhole-tree harvesting. B. pendula and P. abies had higher quantities and average concentrations of Zn in the biomass. For all species, >50% of the Zn in the stems was found in the bark. P. abies and L. sibirica had higher quantities of Cu in the biomass than the other species.P. abies and P. contorta had high quantities of Cd inthe biomass in relation to the other species. Branches and stembark contained high concentrations of Cd and Pb in relation to foliage and stemwood. Dead branches had especially high concentrations of Pb. The high accumulation rate of Zn in thebiomass of B. pendula was related to a low exchangeable amount of Zn in the A horizon. In the superficial centimeters ofthe A horizon, a depletion similar to that found for Zn was detected for Cu, whereas for Cd and Pb, no correlations were found between quantities of elements in the trees and element pools in the soil.  相似文献   

12.
Recent starch-plastic research at the National Center for Agricultural Utilization Research is reviewed and related worldwide efforts are noted. Properties of starch that influence its formulation and performance in plastics are discussed. Methods are given for preparation of starch-poly(methyl acrylate) graft copolymer, starch-poly(ethylene-co-acrylic acid), and starch-poly(ethylene-co-acrylic acid)-polyethylene plastics. Their physical properties are discussed, as is degradability by enzymes or amylolytic organisms from soil, ponds, and streams.The mention of firm names or trade products does not imply that they are endorsed or recommended by the U.S. Department of Agriculture over other firms or similar products not mentioned.  相似文献   

13.
Application of Cellulose Microfibrils in Polymer Nanocomposites   总被引:1,自引:0,他引:1  
Cellulose microfibrils obtained by the acid hydrolysis of cellulose fibers were added at low concentrations (2–10% w/w) to polymer gels and films as reinforcing agents. Significant changes in mechanical properties, especially maximum load and tensile strength, were obtained for fibrils derived from several cellulosic sources, including cotton, softwood, and bacterial cellulose. For extruded starch plastics, the addition of cotton-derived microfibrils at 10.3% (w/w) concentration increased Young’s modulus by 5-fold relative to a control sample with no cellulose reinforcement. Preliminary data suggests that shear alignment significantly improves tensile strength. Addition of microfibrils does not always change mechanical properties in a predictable direction. Whereas tensile strength and modulus were shown to increase during addition of microfibrils to an extruded starch thermoplastic and a cast latex film, these parameters decreased when microfibrils were added to a starch–pectin blend, implying that complex interactions are involved in the application of these reinforcing agents.  相似文献   

14.
高浓度、高盐分的四氮唑生产废水通过三效蒸发浓缩,馏出液经铁炭氧微电解和混凝预处理,再采用水解酸化一接触氧化一反应二沉主体组合工艺进行处理。研究了该工艺所需构筑物和设备的设计与选型。该工艺在正常运行条件下,处理后出水pH6~9,COD 302mg/L,BOD5 108mg/L,SS30mg/L,色度36倍,水质达到GB8978--1996(污水综合排放标准》三级标准。  相似文献   

15.
Bioassessment is a useful tool to determine the impact of logging practices on the biological integrity of streams and wetlands. Measuring biota directly has an intuitive appeal for impact assessment, and biota can be superior indicators to physical or chemical characteristics because they can reflect cumulative impacts over time. Logging can affect stream and wetland biota by increasing sedimentation rates, altering hydrologic, thermal, and chemical regimes, and changing the base of food webs. Biotic impacts of logging on streams compared to wetlands probably differ, and in this paper we review some of those differences. In streams, invertebrates, fishes, amphibians, algae, and macrophytes have been used as indicators of logging impacts. In wetlands, bioassessment is just beginning to be used, and plants and birds are the most promising indicator taxa. Various best management practices (BMPs) have been developed to reduce the impacts of logging on stream and wetland biota, and we review quantitative studies that have evaluated the efficacy of some of these techniques in streams and wetlands in the eastern United States. Remarkably few studies that address the overall efficacy of BMPs in limiting biotic changes in streams and wetlands after BMP implementation have been published in scientific journals, although some work exists in reports or is unpublished. We review these works, and compile conclusions about BMP efficacy for biota from this body of research.  相似文献   

16.
Air emissions and residual ash samples were collected and analyzed during experiments of open, uncontrolled combustion of electronic waste (e-waste), simulating practices associated with rudimentary e-waste recycling operations. Circuit boards and insulated wires were handled separately to simulate processes associated with metal recovery. The average emissions of polychlorinated dibenzodioxins and dibenzofurans (PCDD/PCDFs) were 92 ng toxic equivalency (TEQ)/kg [n = 2, relative standard deviation (RSD) = 98%] and 11 900 ng TEQ/kg (n = 3, RSD = 50%) of the initial mass of the circuit boards and insulated wire, respectively. The value for the insulated wire is about 100 times higher than that for backyard barrel burning of domestic waste. The emission concentrations of polybrominated dibenzodioxins and dibenzofurans (PBDD/PBDFs) from the combustion of circuit boards were 100 times higher than for their polychlorinated counterparts. Particulate matter (PM) sampling of the fly ash emissions indicated PM emission factors of approximately 15 and 17 g/kg of the initial mass for the circuit boards and insulated wire, respectively. Fly ash samples from both types of e-waste contained considerable amounts of several metallic elements and halogens; lead concentrations were more than 200 times the United States regulatory limits for municipal waste combustors and 20 times those for secondary lead smelters. Leaching tests of the residual bottom ash showed that lead concentrations exceeded U.S. Environmental Protection Agency landfill limits, designating this ash as a hazardous waste.  相似文献   

17.
In 1994, a large survey of soil chemistry was undertaken in thecounty of Värmland in central Sweden (Lundström et al., 1998).The southern part of the county was affected by soilacidification whereas there were no such indications in thenorthern part. To investigate the influence of soil chemistryon the trees at the specific sites, the survey was continued byan analysis of needle chemistry (Norway spruce) which wasundertaken at 150 of the 180 sites, and of tree growth at 65 ofthe 180 sites. Growth was expressed as a ratio between expectedgrowth, estimated with a national, empirical growth model, andthe growth observed in the field. In statistical analyses,using rank correlation, PCA and PLS, there were only weakindications of an influence of soil chemistry on needlechemistry and on tree growth. A moderate correlation betweennitrogen and sulphur in needles was found, which wasinterpreted as an effect of deposition and of processes in thetree canopy. No obvious regional pattern of the growth ratiowas found, in contrast to the clear pattern of soilacidification. The statistical analysis could not with anycertainty point out any of the soil chemistry variables asespecially important for the tree growth ratio.  相似文献   

18.
The solubility and potential mobility of heavy metals (Cd, Cu,Hg, Pb and Zn) in two urban soils were studied by sequential andleaching extractions (rainwater). Compared to rural (arable) soils on similar parent material, the urban soils were highlycontaminated with Hg and Pb and to a lesser extent also with Cd,Cu and Zn. Metal concentrations in rainwater leachates were related to sequential extractions and metal levels reported fromStockholm groundwater. Cadmium and Zn in the soils were mainly recovered in easily extractable fractions, whereas Cu and Pb were complex bound. Concentrations of Pb in the residual fractionwere between two- and eightfold those in arable soils, indicatingthat the sequential extraction scheme did not reflect the solidphases affected by anthropogenic inputs. Cadmium and Zn conc. inthe rainwater leachates were within the range detected in Stockholm groundwater, while Cu and Pb conc. were higher, whichsuggests that Cu and Pb released from the surface soil were immobilised in deeper soil layers. In a soil highly contaminatedwith Hg, the Hg conc. in the leachate was above the median concentration, but still 50 times lower than the max concentration found in groundwater, indicating the possibilityof other sources. In conclusion, it proved difficult to quantitatively predict the mobility of metals in soils by sequential extractions.  相似文献   

19.
During recent decades heathlands havechanged into grasslands in regions with high atmosphericnitrogen deposition. In regions with intermediatedeposition level (e.g., Denmark) changes have been lesspronounced which may be due to delay or decrease inresponse of the ecosystem. The mor layer (O horizon) mayplay an important role for this delay due to high sinkstrength for N. In this study, the capacity for netNH4 + immobilization and mineralization wasstudied during short- and long-term incubations (2–36 days)of mor samples from Danish dry inland heaths. High short-term capacity for net NH4 + immobilization wasfound to be a general characteristic of Danish heath morlayers both under heather (Calluna vulgaris) andcrowberry (Empetrum nigrum ssp nigrum), the latterdominating late stages in heathland succession. The netNH4 + immobilization was higher under youngcompared to old or dead vegetation, and higher on lessnutrient poor soils than on extremely nutrient poor soils.The addition of N, P and C stimulated CO2 productionand net NH4 + immobilization, but not net Nmineralization. The immobilization of 15NH4 +caused release of dissolved organic N, increased N anddecreased C/N ratio in the microbial biomass, and indicatedgrowth of microorganisms with other metabolic abilitiesthan the indigenous population. No evidence was obtained ofstabilization of immobilized 15NH4 + intosoil organic matter during the experiment. On background ofthe results and current knowledge it was concluded that therecognition of the high capacity for net NH4 +immobilization in mor layers does not allow for a raiseof critical loads for N for northern dry inland heaths.  相似文献   

20.
Injection molded specimens were prepared by blending poly (hydroxybutyrate-co-valerate) (PHBV) with cornstarch. Blended formulations incorporated 30% or 50% starch in the presence or absence of poly-(ethylene oxide) (PEO), which enhances the adherence of starch granules to PHBV. These formulations were evaluated for their biodegradability in natural compost by measuring changes in physical and chemical properties over a period of 125 days. The degradation of plastic material, as evidenced by weight loss and deterioration in tensile properties, correlated with the amount of starch present in the blends (neat PHBV < 30% starch < 50% starch). Incorporation of PEO into starch-PHBV blends had little or no effect on the rate of weight loss. Starch in blends degraded faster than PHBV and it accelerated PHBV degradation. Also, PHBV did not retard starch degradation. After 125 days of exposure to compost, neat PHBV lost 7% of its weight (0.056% weight loss/day), while the PHBV component of a 50% starch blend lost 41% of its weight (0.328% weight loss/day). PHB and PHV moieties within the copolymer degraded at similar rates, regardless of the presence of starch, as determined by 1H-NMR spectroscopy. GPC analyses revealed that, while the number average molecular weight (Mn) of PHBV in all exposed samples decreased, there was no significant difference in this decrease between neat PHBV as opposed to PHBV blended with starch. SEM showed homogeneously distributed starch granules embedded in a PHBV matrix, typical of a filler material. Starch granules were rapidly depleted during exposure to compost, increasing the surface area of the PHBV matrix.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号