万山汞矿区土壤重金属污染特征及来源解析

以万山汞矿区土壤为研究对象,采用电感耦合等离子体质谱仪和原子荧光光谱仪测定土壤中的重金属含量,分别运用内梅罗综合污染指数（NPI）法和潜在生态风险指数（RI）法评价土壤重金属污染和潜在生态风险,并应用相关性分析、主成分分析和聚类分析对土壤重金属来源进行分析。结果表明：土壤Hg、Cd、As、Pb、Cu、Ni和Zn出现不同程度累积,分别达贵州省背景值的263.61、2.31、1.28、2.11、1.70、1.01和3.52倍;土壤重金属平均NPI为188.00,属于严重污染水平,Hg是主要污染因子;土壤重金属平均RI为10 655.70,属于极强潜在生态风险水平,Hg是主要潜在生态风险因子;土壤中Cu、Ni、Cr主要源于自然活动,As、Pb、Zn主要源于燃煤和交通运输污染,Cd主要源于农业污染,Hg主要源于汞冶炼污染。     

复合重金属污染高岭土的电动修复

根据电子废弃物拆解场地的污染特征,以复合重金属(Cu,Cd,Pb)污染高岭土为研究对象,考察了电动技术对污染土壤的修复效果。实验结果表明:在电压梯度为1 V/cm、阳极液为自来水、阴极液为柠檬酸-柠檬酸钠缓冲液(pH=5)、靠近阴极设置活性炭渗透反应墙(PRB)的条件下电动修复96 h后,Cu,Cd,Pb的平均去除率分别可达79.93%,99.43%,39.36%;土壤的酸碱性对电动修复效果影响显著,通过在阴极添加缓冲液维持土壤偏酸性条件,有利于重金属污染物的电动去除;在靠近阴极设置活性炭PRB可富集重金属,减少阴极液的污染;迁移率大的酸可提取态重金属较易去除,残渣态重金属稳定性强,去除率较低。     

Using biopolymers to remove heavy metals from soil and water

Chemical remediation of soil may involve the use of harsh chemicals that generate waste streams, which may adversely affect the soil's integrity and ability to support vegetation. This article reviews the potential use of benign reagents, such as biopolymers, to extract heavy metals. The biopolymers discussed are chitin and chitosan, modified starch, cellulose, and polymer-containing algae.     

Removal techniques for heavy metals from fly ash

This study reviews different technologies for extraction of heavy metals from fly ash. With this perspective processes like bioleaching using microbes, carrier in pulp method, chemical extraction via acids, alkaline leachates and chelating agents, chloride evaporation process, electrodialytic and thermal treatments were studied thoroughly. A comprehensive comparison of all the techniques is also done by studying in detail their reaction conditions, metals leached and percentage extraction achieved. The study concluded that depending on the type of fly ash and metal under consideration determines the suitability of the process adopted for detoxification of fly ash. In addition to these, factors like cost, time and energy also define the final selection process.     

Characterizing soils contaminated with heavy metals: A uranium contamination case study

To stem rising remediation costs for soils contaminated with hazardous metals, increased emphasis is being placed on the development of in-situ and ex-situ treatment technologies. Often, a lack of basic information on the chemical and physical characteristics of the soil and contaminants hampers treatability studies used to design these technologies. This article proposes and demonstrates a characterization program to meet these information needs, employing standard analytical techniques coupled with advanced spectroscopy and microscopy techniques. To support treatments involving physical separation strategies, the program uses standard analytical techniques to characterize the soil and the association of contaminants with different soil fractions (e.g., size and density fractions). Where chemical treatments are required, spectroscopy and microscopy methods are employed to yield quantitative information on the oxidation state and speciation of the contaminant. Examples demonstrate the use of measured soil and contaminant characteristics in the screening of alternative treatment technologies and in the selection of soils for use in treatability studies. Also demonstrated is the use of these characterization tools in the design and optimization of treatment strategies and in support of risk assessment determinations.     

Comparison of methods for leaching heavy metals from composts

This paper presents the determination of total iron, copper, zinc, chromium, nickel, lead, cadmium and mercury contents in the compost obtained from sorted municipal organic solid waste applying the following methods of sample mineralization: 40% hydrofluoric acid with preliminary incineration of a sample, a mixture of concentrated nitric(V) and chloric(VII) acids with preliminary incineration of organic matter and a mixture of nitric(V) and chloric(VII) acids without sample incineration. The speciation analysis of Tessier was used to estimate the bioavailability of the metals. Elution degrees of the mobile forms of the metals from the compost with 10% nitric(V) acid and 1 mol/dm(3) hydrochloric acid were compared. The contents of the elements in the eluates were determined applying atomic absorption spectrometry.     

Effect of technology development on potential environmental impacts from heavy metals in waste smartphones

Technology development has brought beneficial changes in the functions of smartphones but has the potential to impact the environment due to the high generation of waste smartphones. Thus, this study evaluates and compares environmental impact potentials from metals in waste smartphones to figure out the effect of smartphone model replacements on hazardous waste, resource depletion, and toxicity potentials. The total threshold limit concentration (TTLC) analysis is used to determine whether the waste smartphones would be classified as hazardous waste, and the life-cycle impact assessment methods are used to evaluate resource depletion, cancer, non-cancer, and ecotoxicity potentials. The TTLC results showed that the smartphone technology development did not reduce hazardous waste potentials. The life-cycle impact assessment results showed that the technology development overall reduced resource depletion potential but increased toxicity potential. In addition, priority metals contributing to the potentials were identified to effectively manage their environmental impacts. This study can provide fundamental information for smartphone manufacturers, waste smartphone recyclers and disposers, and e-waste policymakers to circulate resources and to prevent environmental pollutions from hazardous and toxic materials.     

Comparison of three ornamental plants for phytoextraction potential of chromium removal from tannery sludge

Based on pre-experimentation, three ornamental plants, Mirabilis jalapa, Impatiens Balsamin (I. Balsamin) and Tagetes erecta L., were selected as target plants to study the phytoextraction of chromium (Cr) in tannery sludge irrigated with four treatments according to Cr concentration gradient [Control (CK); 20.50 × 10³ mg kg^?1 (T1); 51.25 × 10³ mg kg^?1 (T2); 102.50 × 10³ mg kg^?1 (T3)]. Results of pot experiments showed that the biomass of Mirabilis jalapa and Tagetes erecta L. had no significant differences among the four treatments, while I. Balsamin showed a decline trend in the biomass with the increase of Cr concentration, probably due to some extent to the poisoning effect of Cr under treatment T2 or T3. Mirabilis jalapa accumulated Cr concentration, with 408.97, 124.97, 630.16 and 57.30 mg kg^?1 in its roots, stems, leaves and inflorescence, respectively. The translocation factor and the bioaccumulation coefficient of Mirabilis jalapa are each greater than 1, indicating that Mirabilis jalapa has the strong ability to tolerate and enrich Cr by biological processes. Comparing accumulation properties of the three ornamental plants, in the amount and allocation, Mirabilis jalapa showed the highest phytoextraction efficiency and could grow well at the high Cr concentration. Our experiments suggest that Mirabilis jalapa is the expected flower species for Cr removal from tannery sludge.     

Sorbents for the removal of airborne heavy metals from incinerator effluent

The effectiveness of inorganic alumino-silicate sorbents (alumina and kaolinite) to adsorb airborne lead and cadmium from the effluent stream of a simulated waste incinerator was studied. A 20 kW (68,000 BTU/h) flow reactor was used to achieve the temperature and residence times typical of a waste incinerator. Solutions containing lead or cadmium were introduced yielding airborne metals concentrations between 15 and 150 ppm. Gas samples were drawn into a particle impactor that collected the airborne particles and condensed phase metal aerosols, separating them into ten size ranges from 0.2 μm to greater than 10 μm. Metals to sorbent mass ratios between 0.03 and 1.56 were investigated. Scavenging efficiency increased as the ratio of sorbent to injected metal mass was increased. The scavenging efficiencies were as high as 76% for lead scavenged by kaolinite to as low as 14% for cadmium scavenged by alumina.     

Acidic bioleaching of heavy metals from sewage sludge

The overall objective of this study was to evaluate the use of controlled bio-acidification prior to land application as a decontamination process to remove heavy metals from sludge. The sulfur-oxidizing bacteria were naturally available in the sludge samples and were activated by providing sulfur and aeration at 28°C–30°C. Activation resulted in bio-acidification to pH 2 within 5–11 days. Successive inoculation of fresh sludges with 5% acidified samples reduced the acidification time to 2–3 days in most samples. Bio-acidification resulted in dissolving significant quantities of heavy metals from all sludge types tested. The maximum solubilization results were: 86%–97% for Ni; 48%–98% for Pb; 26%–71% for Cr; 18%–91% for Zn; 16%–90% for Cu; 7%–60% for Cd. Limited metal solubilization results were observed in the various control samples that accompanied the bio-acidified samples. The leaching results in the control samples were limited to 2%–19% for Ni, 0%–7% for Pb, 0%–5% for Cr, 0.3%–4% for Zn, 0.2%–4% for Cu and 0%–3% for Cd. The results confirmed that Ni and Pb were the easiest metals to dissolve from the various sludge types. On the other hand, the lowest solubilization results were observed for Cu and Cd, and moderate solubilization results were achieved for Cr. The bio-acidification process resulted in moderate gains in terms of improving the suitability of tested sludges for land application. Received: April 19, 1999 / Accepted: November 4, 1999     

Recovery of copper from contaminated soil by flushing

In this work the development of a process for the recovery of copper from contaminated industrial soils is presented. Experimental tests on a standard soil contaminated with a solution of copper chloride were carried out. The metal was extracted from the contaminated soil by flushing with a 0.1 M aqueous solution of an ethylenediaminetetraacetic acid (EDTA) sodium salt. A maximum copper extraction efficiency of about 60% was observed. Copper was then separated from the extracted solution by precipitation with sodium hydroxide after addition of ferric sulfate.     

Enhanced phytoremediation: A study of mycorrhizoremediation of heavy metal–contaminated soil

Arbuscular mycorrhizal fungi (AMF) are microscopic fungi that occur naturally in soil and form a symbiosis with plant roots. By colonizing the roots, the fungus increases plant growth by making soil essential elements like zinc and phosphorus more accessible. AMF can play a role in the phytoremediation of heavy metal–contaminated soil (mycorrhizoremediation). Two research experiments were conducted to evaluate the impact of AMF on the extraction of different heavy metals (arsenic, cadmium, lead, selenium, and zinc) in contaminated soil. A grass mixture composed of Festuca rubra, Festuca eliator, Agropyron repens, and Trifolium repens was used in the experiments, and four different types of AMF were investigated: Glomus intraradices, Glomus mosseae, Glomus etunicatum, and Gigaspora gigantea. The results of the study showed that heavy metal extraction by Glomus intraradices colonized plants was the highest of all four AMF tested and was generally higher than nonmycorrhizal plants, depending on the heavy metal concentration in soil and whether it interacted with other metals in soil. However, metal extraction by AMF colonized grasses reached a plateau after an approximately two‐month period showing no further phytoaccumulation. © 2006 Wiley Periodicals, Inc.     

Phytoremediation: The uptake of metals and metalloids by rhodes grass grown on metal‐contaminated soil

An experiment was performed to examine the phytoremediation potential of Rhodes grass (Chloris gayana Kunth cv. ‘Pioneer’). The study sought to determine substrate tolerance, biomass production, and plant uptake of antimony (Sb), arsenic (As), cadmium (Cd), lead (Pb), silver (Ag), and zinc (Zn). The plants were grown on weight percent mixtures (5 percent, 15 percent, 25 percent, 35 percent, 50 percent) of a vertisol soil and base‐metal mine tailings (7–2,040 μg/g As, ≥ 30 μg/g Cd, 30–12,000 μg/g Pb, and 72–4,120 μg/g Zn). The 5 percent and 15 percent amendment of mine tailings increased the biomass production of Rhodes grass (from 0.1 g/plant to ≈ 3.5 g/plant) without appreciably elevating plant concentrations of the elements. Plant growth decreased by greater than 50 percent for the substrate containing greater than 25 percent tailings (3,023 μg/g Pb and 1,084 μg/g Zn). Reduced biomass production coincided with maximal Zn uptake by Rhodes grass (249.8 μg/g), indicating tailings induced phytotoxicity. The total concentrations of metals and metalloids tolerated by Rhodes grass in the plant‐growth medium indicated hypertolerance to elevated As, Pb, and Zn concentrations. Partial extraction of the plant‐growth medium determined that plant‐available Pb was ten times higher than Ag, As, Cd, and Zn availability. However, Rhodes grass accumulated low levels of Pb, in addition to As and Cd, over the experimental range, indicating low fodder toxicity risk to browsing livestock. This study concludes that if there are no invasive species issues associated with conservation land uses, Rhodes grass is well suited to metalliferous mined land revegetation and would therefore be highly effective for such programs in subtropical and tropical Australia. © 2005 Wiley Periodicals, Inc.     

The environmental fate of heavy metals arising from a MSW incineration plant

Pollutant fluxes from municipal solid waste (MSW) incinerators are of a certain concern, especially gaseous emissions from the stack, which constitute the major effluent from the plant. In this work, heavy metals in soil and vegetation sampled in different sites around the plant are compared with those found in the gaseous emissions from an incinerator: the suspected source and environmental matrices are observed together, in order to detect a possible relationship of cause and effect, using statistical methods. The incinerator examined, regarding dimension and technology, can be considered a typical Italian one. Heavy metal concentrations in soil and vegetation show a clear dependence on sampling year; similar behaviour can be found in emission fluxes referring to the same years. A dependence on the distance from the incinerator is also apparent. This study supplies a methodological approach that can be easily extended and applied to other suspected contamination sources.     

Leachability of heavy metals from copper blasting grit waste

This investigation presents the results of leaching tests, using the multiple-batch procedure, on cadmium, zinc, copper, lead, and chromium from copper blasting grit waste generated from a shipbuilding and repair company in Bahrain. The leaching test results have demonstrated that the metals tested were generally released in low concentrations except for copper and zinc. Metal leachability appeared to be dependent upon the pH and composition of the leaching medium.     

石油污染土壤的微生物修复技术

介绍了石油污染土壤微生物修复技术的影响因素;概述了生物刺激、生物强化、固定化微生物、植物-微生物联合修复以及电动-微生物联合修复石油污染土壤的技术原理,分析了现阶段土壤修复过程中面临的难题,预测了微生物修复技术的研究方向。指出优化微生物的环境条件、培育新型高效的基因工程菌和开发经济高效的新型修复技术等将是未来微生物修复技术的发展趋势。     

典型磷矿区表层土壤重金属空间分布特征研究

以开阳磷矿区为对象,结合地统计学普通克里金插值法以及单因素分析法,研究了矿区表层土壤重金属的空间分布特征,并对其进行了污染评价。结果表明：以矿区当地土壤重金属背景值为标准,Cu,Zn,Pb,Cd,As含量均存在超标情况;5种元素含量的变异程度均为高度变异,Pb,Cd,As的变异系数远大于Cu,Zn的变异系数;土壤重金属空间分布特征为Cd,As含量在东北部的积累程度大于西南部,东北—东南方向Cu,Zn,Pb,Cd,As的富集程度远大于西北—西南方向;不同土地利用类型对重金属的积累没有显著影响,这很可能与其他因素如背景值、风向、人类干扰（如化工产业）等有关。