Rapid Cleanup of Chlorinated Solvent Source Zones: Synergies Between Chemical and Biological Degradation

A chlorinated volatile organic compound (cVOC) source area approximately 25 by 100 ft in a heavily industrialized urban area was characterized with groundwater tetrachloroethene (PCE) concentrations up to 9,180 μg/L. This is approximately 6 percent of PCE's aqueous solubility, indicative of the presence of residual dense, nonaqueous phase liquid. The resulting dissolved‐phase plume migrated off‐site. Biotic and abiotic dechlorination using a combination of a food‐grade organic carbon‐based electron donor and zero‐valent iron suspended in a food‐grade emulsifying agent reduced the source area PCE concentrations by 98 percent within 27 weeks, with minimal downgradient migration of daughter products dichloroethene and vinyl chloride. Combining biological dechlorination with iron‐based chemical dechlorination is synergistic, enhancing treatment aggressiveness, balancing pH, and optimizing degradation of both DNAPL and dissolved‐phase cVOCs. © 2013 Wiley Periodicals, Inc.     

Remedial options for chlorinated volatile organics in a partially anaerobic aquifer

A laboratory study was conducted for the selection of appropriate remedial technologies for a partially anaerobic aquifer contaminated with chlorinated volatile organics (VOCs). Evaluation of in situ bioremediation demonstrated that the addition of electron donors to anaerobic microcosms enhanced biological reductive dechlorination of tetrachloroethene (PCE), trichloroethene (TCE), and 1,1,1‐trichloroethane (1,1,1‐TCA) with half‐lives of 20, 22, and 41 days, respectively. Nearly complete reductions of PCE, TCE, 1,1,1‐TCA, and the derivative cis‐dichloroethene were accompanied by a corresponding increase in chloride concentrations. Accumulation of vinyl chloride, ethene, and ethane was not observed; however, elevated levels of ¹⁴CO₂ (from ¹⁴C‐TCE spiked) were recovered, indicating the occurrence of anaerobic oxidation. In contrast, very little degradation of 1,2‐dichloropropane (1,2‐DCP) and 1,1‐dichlorethane (1,1‐DCA) was observed in the anaerobic microcosms, but nutrient addition enhanced their degradation in the aerobic biotic microcosms. The aerobic degradation half‐lives for 1,2‐DCP and 1,1‐DCA were 63 and 56 days, respectively. Evaluation of in situ chemical oxidation (ISCO) demonstrated that chelate‐modified Fenton's reagent was effective in degrading aqueous‐phase PCE, TCE, 1,1,1‐TCA, 1,2‐DCP, etc.; however, this approach had minimal effects on solid‐phase contaminants. The observed oxidant demand was 16 g‐H₂O₂/L‐groundwater. The oxidation reaction rates were not highly sensitive to the molar ratio of H₂O₂:Fe²⁺:citrate. A ratio of 60:1:1 resulted in slightly faster removal of chemicals of concern (COCs) than those of 12:1:1 and 300:1:1. This treatment resulted in increases in dissolved metals (Ca, Cr, Mg, K, and Mn) and a minor increase of vinyl chloride. Treatment with zero‐valent iron (ZVI) resulted in complete dechlorination of PCE, and TCE to ethene and ethane. ZVI treatment reduced 1,1,1‐TCA only to 1,1‐DCA and chloroethane (CA) but had little effect on reducing the levels of 1,2‐DCP, 1,1‐DCA, and CA. The longevity test showed that one gram of 325‐mesh iron powder was exhausted in reaction with > 22 mL of groundwater. The short life of ZVI may be a barrier to implementation. The ZVI surface reaction rates (k_sa) were 1.2 × 10^?2 Lm^?2h^?1, 2 × 10^?3 Lm^?2h^?1, and 1.2 × 10^?3 Lm^?2h^?1 for 1,1,1‐TCA, TCE, and PCE, respectively. Based upon the results of this study, in situ bioremediation appeared to be more suitable than ISCO and ZVI for effectively treating the groundwater contamination at the site. © 2004 Wiley Periodicals, Inc.     

Coupling surfactants/cosolvents with oxidants for enhanced DNAPL removal: A review

Surfactants and cosolvents are useful for enhancing the apparent solubility of dense nonaqueous‐phase liquid (DNAPL) compounds during surfactant‐enhanced aquifer remediation (SEAR). In situ chemical oxidation (ISCO) with permanganate, persulfate, and catalyzed hydrogen peroxide has proven to be a cost‐effective and viable remediation technology for the treatment of a wide range of organic contaminants. Coupling compatible remedial technologies either concurrently or sequentially in a treatment train is an emerging concept for more effective cleanup of DNAPL‐contaminated sites. Surfactants are effective for DNAPL mass removal but not useful for dissolved plume treatment. ISCO is effective for plume control and treatment but can be less effective in areas where large masses of DNAPL are present. Therefore, coupling SEAR with ISCO is a logical next step for source‐zone treatment. This article provides a critical review of peer‐reviewed scientific literature, nonreviewed professional journals, and conference proceedings where surfactants/cosolvents and oxidants have been utilized, either concurrently or sequentially, for DNAPL mass removal. © 2010 Wiley Periodicals, Inc.     

Bioventing of No. 2 Fuel Oil: Effects of Air Flowrate,Temperature, Nutrient Amendment,and Acclimation

A 14‐month pilot‐scale bioventing study, sponsored by the New Hampshire Department of Environmental Services, was conducted by the University of New Hampshire to determine the effects of the time between the contamination event and the onset of bioventing, as well as air flowrate, temperature, and nutrient amendments. Freshly contaminated soil was not readily amenable to bioventing. Bioventing was effective (82–92.5 percent removal) for acclimated soil amended with nutrients at 10 °C and 20 °C for the 275 cm³/min and 140 cm³/min air flowrates, respectively. First order degradation rates after nutrient addition were ?6.11 ± 0.83 (×10^?3)/day and ?6.57 ± 1.71 (×10^?3)/day, respectively. The results indicate that bioventing will be best applied when the contamination has occurred at least two years before the onset of treatment. © 2014 Wiley Periodicals, Inc.     

Pilot‐scale evaluation using bioaugmentation to enhance PCE dissolution at dover AFB national test site

An Interstate Technology and Regulatory Council (ITRC) forum was recently held that focused on six case studies in which bioremediation of dense nonaqueous‐phase liquids (DNAPLs) was performed; the objective was to demonstrate that there is credible evidence for bioremediation as a viable environmental remediation technology. The first two case studies from the forum have been previously published; this third case study involves a pilot‐scale demonstration that investigated the effects of biological activity on enhancing dissolution of an emplaced tetrachloroethene (PCE) DNAPL source. It used a controlled‐release test cell with PCE as the primary DNAPL in a porous media groundwater system. Both laboratory tests and a field‐scale pilot test demonstrated that bioaugmentation can stimulate complete dechlorination to a nontoxic end product and that the mass flux from a source zone increases when biological dehalorespiration activity is enhanced through nutrient (electron donor) addition and bioaugmentation. All project goals were met. Important achievements include demonstrating the ability to degrade a PCE DNAPL source to ethene and obtaining significant information on the impacts to the microbial populations and corresponding isotope enrichments during biodegradation of a source area. © 2007 Wiley Periodicals, Inc.     

Successful unsaturated zone treatment of PCE with sodium permanganate

In situ chemical oxidation (ISCO) with permanganate has been widely used for soil and groundwater treatment in the saturated zone. Due to the challenges associated with achieving effective distribution and retention in the unsaturated zone, there is a great interest in developing alternative injection technologies that increase the success of vadose‐zone treatment. The subject site is an active dry cleaner located in Topeka, Kansas. A relatively small area of residual contamination adjacent to the active facility building has been identified as the source of a large sitewide groundwater contamination plume with off‐site receptors. The Kansas Department of Health and Environment (KDHE) currently manages site remedial efforts and chose to pilot‐test ISCO with permanganate for the reduction of perchloroethene (PCE) soil concentrations within the source area. KDHE subsequently contracted Burns & McDonnell to design and implement an ISCO pilot test. A treatability study was performed by Carus Corporation to determine permanganate‐soil‐oxidant‐demand (PSOD) and the required oxidant dosing for the site. The pilot‐test design included an ISCO injection approach that consisted of injecting aqueous sodium permanganate using direct‐push technology with a sealed borehole. During the pilot test, approximately 12,500 pounds of sodium permanganate were injected at a concentration of approximately 3 percent (by weight) using the methods described above. Confirmation soil sampling conducted after the injection event indicated PCE reductions ranging from approximately 79 to more than 99 percent. A follow‐up treatment, consisting of the injection of an additional 6,200 pounds of sodium permanganate, was implemented to address residual soil impacts remaining in the soil source zone. Confirmation soil sampling conducted after the treatment indicated a PCE reduction of greater than 90 percent at the most heavily impacted sample location and additional reductions in four of the six samples collected. © 2009 Wiley Periodicals, Inc.     

Bioremediation of a former dry cleaner using potassium lactate

Chlorinated solvents were released to the surficial groundwater underneath a former dry cleaning building, resulting in a groundwater plume consisting of high concentrations of trichloroethene (TCE) and cis‐1,2‐dichloroethene (cis‐1,2‐DCE) and low concentrations of tetrachloroethene (PCE) and vinyl chloride. The initial remedial action included chemical oxidation via injection of 14,400 gallons of Fenton's Reagent in March 2002, and an additional 14,760 gallons in April 2002. A sharp reduction of contaminant concentrations in groundwater was observed the following month; however, rebound of contaminant concentrations was evident as early as October 2002. A source area of PCE‐impacted soils was excavated in June 2004. Following the excavation, Golder Associates Inc. (2007) implemented a biostimulation plan by injecting 55 gallons of potassium lactate (PURASAL® HiPure P) in September 2005, and again in February 2006. Comparing the preinjection and postinjection site conditions, the potassium lactate treatments were successful in accomplishing a 40 to 70 percent reduction in mass within four months following the second injection. Elevated vinyl chloride concentrations have persisted through both injection events; however, significant vinyl chloride reduction has been observed in one well with the highest total organic carbon (TOC) concentrations following each injection. © 2008 Wiley Periodicals, Inc.     

Stability of Aqueous Suspensions of Medium-Chain-Length Poly-3-Hydroxyalkanoate Particles

Although poly-3-hydroxyalkanoates (PHAs) and particularily medium-chain-length (mcl)-PHAs are likely to find industrial applications in a latex form, very few studies have examined their behavior in aqueous suspension and none have examined the dense suspensions required commercially. For this reason, the stability of mcl-PHA latexes containing saturated aliphatic (65 mol% 3-hydroxynonanoate, PHN), and for the first time, with vinyl (PHNU) or carboxylated side chains was examined. At 4 g L^?1 with no stabilizing agent, PHNU nanoparticles (199.4 ± 3.6 nm) were significantly smaller than those of PHN (211.5 ± 6.4 nm) while carboxylated PHN nanoparticles (76.1 ± 6.4 nm) were substantially smaller than those of either PHN or PHNU with particles stable for more than 110 days. Increasing the PHN concentration to 10 g L^?1 also resulted in stable latexes but with larger particles (410.8 ± 5.2 nm). Adjusting the pH of the suspending medium (water) before addition of the polymer (dissolved in acetone) resulted in much smaller PHN particles at pH = 11.3 (134 ± 2 nm) than at pH = 4.3 (312 ± 8 nm) at a 4 g L^?1 final polymer concentration. Zeta potentials of PHN suspensions decreased with pH, likely due to the carboxyl end groups. Above a pH of 4.0, adjusting the pH after particle formation had little effect. NaCl addition could be used to agglomerate and ultimately precipitate the particles. Stabilizers such as surfactants will likely be required to produce denser mcl-PHA latexes with suitable particle size for certain applications such as coatings and toner production.     

Spreadsheet‐based modeling of ISCO with permanganate

CDISCO, a Microsoft Excel spreadsheet–based model, can be used to assist with the design of in situ chemical oxidation (ISCO) systems using permanganate (MnO₄^?). The model inputs are the aquifer characteristics (porosity, hydraulic conductivity, effective aquifer thickness, natural oxidant demand, kinetic parameters, contaminant concentrations, etc.), injection conditions (permanganate injection concentration, flow rate, and duration), and unit costs for reagent, drilling, and labor. MnO₄^? transport in the aquifer is simulated and used to estimate the effective radius of influence (ROI) and required injection point spacing. CDISCO then provides a preliminary cost estimate for the selected design conditions. The user can perform multiple runs of CDISCO to optimize the cost of the ISCO design. Comparisons with analytical and numerical models of nonreactive and reactive transport demonstrate that CDISCO accurately simulates MnO₄^? transport and consumption. Comparison of CDISCO results with the three‐dimensional heterogeneous simulations show that aquifer volume contact efficiency and contaminant mass treatment efficiency are closely correlated with the ROI overlap factor. © 2011 Wiley Periodicals, Inc.     

Sodium Persulfate Oxidation for the Remediation of Chlorinated Solvents (USEPA Superfund Innovative Technology Evaluation Program)

This study has been conducted at the University of Connecticut (UCONN) in connection with the USEPA Superfund Innovative Technology Evaluation (SITE) program to evaluate a chemical oxidation technology (sodium persulfate) developed at UCONN. A protocol to assess the efficacy of oxidation technologies has been used. This protocol, which consists of obtaining data from a treatability study, tested two in-situ chemical oxidation technologies that can be used on soil and groundwater at a site in Vernon, Connecticut. Based on the treatability report results and additional field data collected at the site, the design for the field implementation of the chemical oxidation remediation was completed. The results indicate that both sodium persulfate and potassium permanganate were able to effectively degrade the target VOCs (i.e., PCE, TCE and cis-DCE) in groundwater and soil-groundwater matrices. In the sodium persulfate tests (120 hrs), the extent of destruction of target VOCs was 74% for PCE, 86% for TCE and 84% for cis-DCE by Na₂S₂O₈ alone and 68% for PCE, 76% for TCE, and 69% for cis-DCE by Fe(II)-catalyzed Na₂S₂O₈. The results demonstrate the sodium persulfate's ability to degrade PCE, TCE and cis-DCE. It is expected that given sufficient dose and treatment time, a higher destruction rate of the dissolved phase contamination can be achieved. The data also indicates that the catalytic effect of the iron chelate on persulfate chemistry was much less pronounced in the soil-groundwater matrix. This indicates an interaction between the iron chelate solution and the soil, which may have resulted in a lower availability of the chelated iron for catalysis. The study showed that the remediation of the VOCs-contaminated soil and groundwater by in-situ chemical oxidation using sodium persulfate is feasible at the Roosevelt Mills site. As a result, the USEPA SITE program will evaluate this technology at this site.     

Chemical and Biological Reduction of PCE by Pneumatic Fracturing and Injection of ZVI in Saprolite

This article presents a case study of the source‐area treatment of tetrachloroethene (PCE) in a low‐permeability formation using zero‐valent iron (ZVI). Evidence of the stimulation of biological reduction processes within the treatment zone occurred. Pneumatic fracturing and injection of microscale ZVI slurry in the overburden and weathered bedrock zones was performed at a commercial brownfields redevelopment site in Maryland. A 20,000‐square‐foot source area impacted with PCE at concentrations greater than 15,000 µg/L was treated at depths ranging from 10 to 70 feet bgs. An average ZVI dosage of 0.0024 iron‐to‐soil mass ratio within the overburden zone led to a 75 percent decrease in PCE mass in less than one year. For the weathered bedrock zone, an average 0.0045 iron‐to‐soil mass ratio resulted in a 92 percent decrease in PCE mass during the same period. The reducing environment and hydrogen generated by the ZVI may have stimulated Dehalobacter populations, as evidenced by concentrations up to 10⁴ cells per milliliter measured within the treatment area despite a groundwater pH as high as 9. The biological reductive dechlorination of the chlorinated ethenes explains the temporary increase in trichloroethene and cis‐1,2‐dichloroethene concentrations. © 2013 Wiley Periodicals, Inc.     

Creosote DNAPL Recovery‐Well Design for Mass Removal

Sites with dense nonaqueous‐phase liquid (DNAPL) contamination present significant remediation challenges in terms of technical practicability and cost. Remedial approaches to DNAPL sites often follow a management approach rather than removal or eradication approaches, particularly due to the uncertainties associated with the benefits of partial source mass removal, as complete source removal is unlikely. Mass‐removal technologies should be evaluated for all DNAPL sites, although implementation of recovery technologies will be limited to a few sites based upon site‐specific factors. Sitewide remedial strategies that employ source reduction, where applicable, and incorporate associated risk‐reduction technologies, including monitored natural attenuation, are advised. Creosote DNAPL sites are particularly challenging, as they are predominantly composed of low‐solubility polycyclic aromatic hydrocarbons that form long‐term continuing sources. Additionally, the physical properties of creosote DNAPL, including high viscosity and relatively low density, result in significant migration potential and considerable dissolved‐phase groundwater impacts. An innovative creosote DNAPL source recovery well design was developed to achieve separate‐phase removal of pooled creosote DNAPL. The design presented herein employs modified circulation‐well technology to mobilize DNAPL to the engineered recovery well, where it is gravity‐settled into a sump to permit separate‐phase mass removal of the emplaced DNAPL source without groundwater production or treatment. A discharge mass flux protocol was developed to verify dissolved‐phase plume stability and the benefit of the source mass removal. © 2013 Wiley Periodicals, Inc.     

DNAPL Source Depletion: 1. Predicting Rates and Timeframes

Given the relatively rapid rate of dense nonaqueous‐phase liquid (DNAPL) ganglia depletion, source zones are generally dominated by horizontal layers of DNAPL after a release to the saturated zone. Estimating the time required to attain specific source strength reduction targets resulting from partial DNAPL source depletion is challenging due to a lack of available screening models, and because little has been done to synthesize available empirical data. Analytical and semi‐analytical models are used to study general DNAPL pool dissolution dynamics. The half‐life for the decline in DNAPL source strength (i.e., aqueous mass discharge) is demonstrated as proportional to the square root of the pool length, the thickness of the pool, and the solubility for single component DNAPLs. The through‐pool discharge is shown to be potentially significant for thin pools or in upper regions of thicker pools. An empirical analysis is used to evaluate average concentration decline rates for 13 in situ chemical oxidation (ISCO) and 16 enhanced in situ bioremediation (EISB) sites. Mean apparent decline rates, based on the time required to achieve the observed source strength reduction, are calculated for the ISCO and EISB sites (half‐lives of 0.39 year and 0.29 year, respectively). The empirical study sites are shown to have faster decline rates than for a large, complex study site where ISCO was implemented (half‐life of 2.5 years), and for a conceptual pool‐dominated trichloroethene source zone where EISB was simulated (half‐life of 2.5 years). Guidance is provided on using these findings in estimating timeframes for partial DNAPL depletion goals. © 2014 Wiley Periodicals, Inc.     

Treatment of tar pond sludge in a circulating fluidized bed combustor

A series of tests to burn mixtures of tar pond sludge and coal was carried out using a mini‐circulating fluidized bed combustor (mini‐CFBC). During the tests, carbon dioxide, oxygen, carbon monoxide, sulfur dioxide, and nitrogen oxides in the flue gas were monitored continuously. Stack gas sampling was carried out for hydrochloric acid, metals, particulate matter, volatile organic compounds (VOCs), total hydrocarbons, semivolatile organic compounds (SVOCs), dioxins and furans (PCDD/Fs), and polychlorinated biphenyls (PCBs). Results showed that hydrochloric acid, mercury, particulate matter, PCDD/F, and metal concentrations were all below both the current limits and the gas‐release limits to be implemented in 2008 in Canada. The new 2008 emissions limits will reduce the maximum allowable concentrations of most pollutants by half. Thus, the maximum concentration for particulate matter will be 5 mg/m³ (from the current maximum concentration of 10 mg/m³);the maximum concentration for hydrochloric acid will be 5 mg/m³ (from 10 mg/m³); and the‐maximum concentration for dioxins and furans will be 0.032 ng/m toxic equivalent (from 0.08 ng/mcurrently). Sulfur capture efficiency was 89–91 percent. The percentage of fuel nitrogen converted to nitrogen oxides was of the order of 4.7 to 6.1, which is significantly lower than that of conventional pulverized coal‐fired boilers and well within the normal range for fluidized bed combustors (FBCs). PCB and polycyclic aromatic hydrocarbon (PAH) emissions levels were comparable or lower than levels reported in the literature for industrial‐scale FBCs. VOC concentrations were low except for benzene, for which the concentration was higher than that reported for pulverized coal‐fired utility boilers. In addition, carbon monoxide concentration was high at 1,200 to 2,200 parts per million. However, these carbon monoxide concentrations are typical of the mini‐CFBC firing coal. The trials showed that for 10 percent by weight tar pond sludge mixed with 90 percent by weight coal, the combustion was both stable and efficient. The tests demonstrated that CFBC technology is an environmentally sound option for eliminating tar pond waste sludge. © 2005 Wiley Periodicals, Inc.     

USING ISOTOPIC AND MOLECULAR DATA TO MODEL LANDFILL GAS PROCESSES

Using a large data set, a preliminary investigation has been made to evaluate the usefulness of stable isotope ratios for improving our understanding of methane and carbon dioxide generation in landfills. Included are approximately 130 landfill gas samples from across the U.S.A., and 18 recent samples from: (1) an Argonne Laboratory study area in the Brea-Olinda Landfill, Orange County, California (U.S.A); and (2) several Los Angeles County landfills, California (U.S.A). The following isotope ratios were examined: δ¹³C for methane, δ¹³C for carbon dioxide and δD for methane. Using simple ratio plots supplemented by mass-balance calculations, these data show promise for indicating the relative contributions of the four major carbon cycle processes in landfills, namely: (1) direct oxidation of organic material to carbon dioxide; (2) methane generation from fermentation (acetate cleavage); (3) methane generation from carbon dioxide reduction; and (4) methane oxidation to carbon dioxide by methanotrophic bacteria. Both the methane generation and oxidation reactions are central to an explanation of the trends discussed herein. The data also suggest that direct oxidation of organic matter in the refuse may be contributing to the observed isotopic ratios in some cases. The trends observed at the Brea-Olinda site were similar to trends using the large U.S. database, suggesting that isotopic techniques may be useful to better constrain carbon cycle processes common to all landfill settings.     

Natural attenuation of chlorinated solvent plumes at Texas dry cleaners

Dry cleaners are the largest users of perchloroethene (PCE) solvents in the United States. Releases from dry cleaners to soil and groundwater, however, remain largely unstudied. This article presents a database of 137 chlorinated solvent plumes at dry cleaners in Texas. The data indicate that PCE plumes are generally shorter in extent than those from industrial sites. Degradation products were observed at more than 80 percent of the sites with groundwater contamination. Calculated attenuation rates are on the order of one‐to‐three‐year half‐lives for PCE and its degradation products. The estimated cleanup timeframe for calculated attenuation rates is < 50 years. More research is needed to understand the presence of organic carbon sources at dry cleaners and its implications for natural attenuation. © 2004 Wiley Periodicals, Inc.     

A Laboratory Assessment of an Innovative Technology for the Detection of DNAPLs

A promising new technology for the detection of dense nonaqueous phase liquids, or DNAPLs, is cosolvent injection/extraction. Cosolvents, such as alcohols, are injected into the subsurface and interact with DNAPLs to increase their aqueous solubility, which increases recovery of the chemicals. A laboratory assessment was performed to determine if incorporating this technology with cone penetrometers could provide a useful sampling tool for DNAPL detection. A cone penetrometer was modeled in the laboratory by injecting and extracting small quantities of ethanol and propylene glycol at low concentrations into a homogeneous sand reactor contaminated with a residual saturation of tetrachloroethene (PCE). Experimental test results show that this technology is extremely sensitive to the vertical placement of the sampler, but is capable of enhancing PCE solubility while recovering most of the alcohol injected. Field testing of this technology will provide the next step in determining the feasibility of this technology for DNAPL detection.     

Remediation of a Former Dry Cleaner Using Nanoscale Zero Valent Iron

Nanoscale zero valent iron (nZVI) was evaluated in a laboratory treatability study and subsequently injected as an interim measure to treat source area groundwater impacts beneath a former dry cleaner located in Chapel Hill, North Carolina (the site). Dry cleaning operations resulted in releases of tetrachloroethene (PCE) that impacted site soil at concentrations up to 2,700 mg/kg and shallow groundwater at concentrations up to 41 mg/L. To achieve a design loading rate of 0.001 kg of iron per kilogram of aquifer material, approximately 725 kg of NanoFe? (PARS Environmental) was injected over a two‐week period into a saprolite and partially weather rock aquifer. Strong reducing conditions were established with oxidation–reduction potential (ORP) values below –728 mV. pH levels remained greater than 8 standard units for a period of 12 months. Injections resulted in near elimination of PCE within one month. cis‐1,2‐Dichloroethene accumulated at high concentrations (greater than 65 mg/L) for 12 months. MAROS software (Version 2.2; AFCEE, 2006 ) was used to calculate mass reduction of PCE and total ethenes at 96 percent and 58 percent, respectively, compared to baseline conditions. Detections of acetylene confirmed the presence of the beta‐elimination pathway. Detections of ethene confirmed complete dechlorination of PCE. Based on hydrogen gas generation, iron reactivity lasted 15 months. © 2013 Wiley Periodicals, Inc.     

Chemical oxidation of tetrachloroethene in a fractured saprolite/bedrock aquifer

Two chemical oxidizers, Fenton's Reagent (FR) and sodium permanganate (NaMnO₄), were used to remediate groundwater contaminated by tetrachloroethene (PCE) in a fractured saprolite and bedrock aquifer in Rockville, Maryland. Initial PCE concentrations ranged from 11 to 25,000 μg/L, averaging 8,684 μg/L in March 2000. A total of 28,256 pounds of hydrogen peroxide (as 35 percent solution) and iron catalyst were injected during the FR treatment program. The FR failed to achieve the desired clean‐up goal, after which 11,114 pounds of NaMnO₄ (as 40 percent solution) were diluted to a 20 percent solution and injected into the aquifer. An additional 855 pounds of dilute NaMnO₄ was later injected, which ultimately reduced the original PCE mass by an estimated 95 percent through November 2001. © 2003 Wiley Periodicals, Inc.     

Influence of mixed molten carbonate composition on hydrogen formation by steam gasification

Steam gasification in the presence of carbonate compounds is an effective method to recover useful materials from electronic waste streams by converting plastics into gaseous products that can be used for energy production and avoiding the expensive manual disassembly process. We investigated steam gasification of activated carbon in the presence of various mixtures of lithium carbonate, sodium carbonate, and potassium carbonate. The activated carbon was almost completely converted into hydrogen and carbon dioxide at 700°C under 0.1 MPa pressure in the presence of carbonate mixtures. Carbon dioxide was also derived from partial decomposition of lithium carbonate. Steam gasification was accelerated in the presence of various carbonate mixtures and at increasing steam partial pressures. These experimental results show that fluidity of carbonates, the potassium content of the carbonate, and the steam partial pressure are important factors in accelerating steam gasification.