Lead in soil by field‐portable x‐ray fluorescence spectrometry—an examination of paired In Situ and laboratory ICP‐AES results

A major aspect of lead hazard control is the evaluation of soil lead hazards around housing coated with lead‐based paint. The use of field‐portable X‐ray fluorescence (FPXRF) to do detailed surveying, with limited laboratory confirmation, can provide lead measurements in soil (especially for planning abatement activities) in a far more cost‐efficient and timely manner than laboratory analysis. To date, one obstacle to the acceptance of FPXRF as an approved method of measuring lead in soil has been a lack of correspondence between field and laboratory results. In order to minimize the differences between field and laboratory results, RTI International (RTI) has developed a new protocol for field drying and sieving soil samples for field measurement by FPXRF. To evaluate this new protocol, composite samples were collected in the field following both U.S. Department of Housing and Urban Development (HUD) guidelines and ASTM International (ASTM) protocols, measured after drying by FPXRF, and returned to the laboratory for confirmatory inductively coupled plasma atomic emission spectroscopy (ICP‐AES) analysis. Evaluation of study data from several diverse sites revealed no statistical difference between paired FPXRF and ICP‐AES measurements using the new method. © 2008 Wiley Periodicals, Inc.     

Evaluation of white‐rot fungi for the remediation of creosote‐contaminated soil

Application of fungal‐based bioaugmentation was evaluated for the remediation of creosote‐contaminated soil at a wood‐preserving site in West Virginia. Soil at the site contained creosote‐range polycyclic aromatic hydrocarbons (PAHs) at concentrations in some areas that exceed industrial risk‐based levels. Two white‐rot fungi (Pleurotus ostreatus and Irpex lacteus) were evaluated for remediation effectiveness in a two‐month bench‐scale treatability test. Both fungi produced similar results, with up to 67.3 percent degradation of total PAHs in 56 days. Pilot‐scale testing was performed at the site using Pleurotus ostreatus grown on two local substrate mixtures. During the 276‐day field trial, total PAHs were degraded by up to 93.2 percent, with all individual PAHs except one achieving industrial risk‐based concentrations. It was recommended that fungal‐based remediation be applied to all contaminated soil at the site. © 2002 Wiley Periodicals, Inc.     

Multiphase extraction radius of influence: Evaluation of design and operational parameters

A common remedial technology for properties with subsurface soil and groundwater contamination is multiphase extraction (MPE). MPE involves the extraction of contaminated groundwater, free‐floating product, and contaminated soil vapor from the subsurface. A network of recovery wells conveys fluids to a vacuum pump and to the treatment system for the contaminated groundwater and soil vapor. This article describes a study of MPE operational data from nine similar remediation projects to determine the most important design parameters. Design equations from guidance manuals were used to estimate the expected radius of influence (ROI) based on measured field data. ROIs were calculated for the vapor flow rate through the subsurface and for the groundwater drawdown caused by the MPE remediation activities. The calculated ROIs were compared to the measured ROIs to corroborate the assumptions made in the calculations. Once it was established that the calculated and field‐measured ROIs were comparable, a sensitivity analysis determined ranges of different design and operational parameters that most affected the ROIs. © 2012 Wiley Periodicals, Inc.     

An ecologically oriented database to guide remediation and reuse of contaminated sites

This article presents a database developed to determine the potential reuse of contaminated sites for primarily ecologically and culturally based activities. The database consists of 172 quantitative and qualitative measures of on‐site land suitability, ecological, cultural, and recreational value, and off‐site suitability, economic, and demographic information. Using sites owned by the U.S. Department of Energy (DOE) as a case study, the article evaluates the quality of available data and suggests ways of using it for planning ecologically sensitive remediation activities and future land use. This type of database can be developed and used by anyone who needs to select, review, or evaluate site remediation and future land use options. Also discussed are the challenges associated with compiling and using data that has been generated by many sources over several years. © 2003 Wiley Periodicals, Inc.     

Increase in remediation processes of oil‐contaminated soils

A study was conducted in the region of the Lena River, in northeast Russia, where oil‐contaminated soil remediation is compromised due to the reduced natural attenuation mechanisms in northern eco‐systems. The goal of the study was to analyze the effectiveness of different biological methods for remediating the permafrost soil cover contaminated with high concentrations of oil. For the remediation of the areas with approximately similar levels of contamination (in the range of 10 to 14 grams per kilogram [g/kg] of soil) different biological remediation schemes were applied: site 1: sowing plant seeds of meadow clover grass; site 2: introducing a consortium of hydrocarbon oxidizing microorganisms (HOM); and, site 3: introducing the same consortium of HOM with simultaneously sowing grass mixture. The third scheme, applied for the first time, led to the most favorable results, which might be explained by the synergistic effect based on the principle of positive inverse development.     

Arsenic and thallium data in environmental samples: Fact or fiction?

Matrix effects may increasingly lead to erroneous environmental decisions as regulatory limits or risk‐based concentrations of concern for trace metals move lower toward the limits of analytical detection. A U.S. Environmental Protection Agency Office of Technical Standards Alert estimated that environmental data reported using inductively coupled plasma spectrometry (ICP‐AES) has a false‐positive rate for thallium of 99.9 percent and for arsenic of 25 to 50 percent. Although this does not seem to be widely known in the environmental community, using three case studies, this article presents data in environmental samples that demonstrate severe matrix effects on the accuracy of arsenic and thallium results. Case Study 1 involves soil results with concentrations that approached or exceeded the applicable regulatory soil cleanup objectives of 13 mg/kg for arsenic and 2 mg/kg for thallium. Reanalysis using ICP coupled with a mass spectrometer (ICP‐MS) confirmed all thallium results were false positives and all arsenic results were biased high, concluding no action was required for soil remediation. Case Study 2 involves groundwater results for thallium at a Superfund site, where thallium was detected in groundwater up to 21.6 μ g/L using ICP‐AES. Reanalysis by ICP‐MS reported thallium as nondetect below the applicable regulatory level in all samples. ICP‐MS is usually a more definitive and accurate method of analysis compared to ICP‐AES; however, this is not always the case, as we demonstrate in Case Study 3, using data from groundwater samples at an industrial site. Through a weight‐of‐evidence approach, it is demonstrated that although method quality control results were acceptable, interferences in some groundwater samples caused biased high results for arsenic using ICP‐MS, which were significantly lower when reanalyzed using hydride generation atomic fluorescence spectrometry. Causes of these interference effects and conclusions from the three case studies to obtain accurate metal data for site assessment, risk characterization, and remedy selection are discussed. © 2010 Wiley Periodicals, Inc.     

Expediting remedial designs and assessments

A successful air-based remediation system, now frequently chosen for sites contaminated with VOCs, demands a thorough understanding of the nature and distribution of the VOCs and the soil air permeabilities. Considering likely remediation methods during the site investigation allows collection of all data needed for method selection and design within a single, highly efficient site visit. A case history illustrates how to integrate several data collection and testing activities into a single site visit.     

Ambient levels of PFOS and PFOA in multiple environmental media

Making remediation and risk management decisions for widely‐distributed chemicals is a challenging aspect of contaminated site management. The objective of this study is to present an initial evaluation of the ubiquitous, ambient environmental distribution of poly‐ and perfluoroalkyl substances (PFAS) within the context of environmental decision‐making at contaminated sites. PFAS are anthropogenic contaminants of emerging concern with a wide variety of consumer and industrial sources and uses that result in multiple exposure routes for humans. The combination of widespread prevalence and low screening levels introduces considerable uncertainty and potential costs in the environmental management of PFAS. PFAS are not naturally‐occurring, but are frequently detected in environmental media independent of site‐specific (i.e., point source) contamination. Information was collected on background and ambient levels of two predominant PFAS, perfluorooctane sulfonate and perfluorooctanoate, in North America in both abiotic media (soil, sediment, surface water, and public drinking water supplies) and selected biotic media (human tissues, fish, and shellfish). The background or ambient information was compiled from multiple published sources, organized by medium and concentration ranges, and evaluated for geographical trends and, when available, also compared to health‐based screening levels. Data coverage and quality varied from wide‐ranging and well‐documented for soil, surface water, and serum data to more localized and less well‐documented for sediment and fish and shellfish tissues and some uncertainties in the data were noted. Widespread ambient soil and sediment concentrations were noted but were well below human health‐protective thresholds for direct contact exposures. Surface water, drinking water supply waters (representing a combination of groundwater and surface water), fish and shellfish tissue, and human serum levels ranged from less than to greater than available health‐based threshold values. This evaluation highlights the need for incorporating literature‐based or site‐specific background into PFAS site evaluation and decision‐making, so that source identification, risk management, and remediation goals are properly focused and to also inform general policy development for PFAS management.     

Perimeter air monitoring for soil remediation

Most environmental project managers are well versed in characterizing and remediating contaminants in soil and water media. When soil remediation activities are conducted at an environmental site, however, some project managers are faced with monitoring contaminants in the air medium for the first time. Remediation activities can disturb contaminants that are normally immobile in soil and transfer them to air. The resulting increase in airborne concentrations of contaminants, even if temporary, may be a health concern for individuals in neighboring residences or businesses. Perimeter air monitoring may be required by a regulatory agency to determine if unhealthy conditions are created and if work practices should be limited or modified. This article serves as a resource for project managers involved in perimeter air monitoring for soil remediation and provides a general summary of candidate sites, remediation activities that release contaminants, regulatory requirements, equipment and target contaminants, monitoring locations and schedule, analytical methods, and data interpretation. © 2007 Wiley Periodicals, Inc.     

Removal,Handling, and Thermal Desorption Treatment Techniques for Manufactured Gas Plant Wastes

Due to the nature of contamination typically found at former MGP (manufactured gas plant) sites, excavation and thermal desorption of MGP wastes has proven to be an effective method for the remediation of MGP‐contaminated soil. The use of on‐site thermal desorption enables MGP sites to be quickly remediated at a low cost. Tar pits, holders, and other underground storage structures typically contain coal tar residuals and waste from former operations, and the areas around these structures are often significantly contaminated. Thus, excavation techniques, odor and vapor management, and material preparation for the treatment method are important factors to consider when developing a site remediation strategy. This article reviews typical excavation and handling methods associated with the remediation of former MGP sites and discusses the treatment of MGP wastes using on‐site thermal desorption technology. © 2001 John Wiley & Sons, Inc.     

Automated continuous monitoring and response to toxic subsurface vapors entering overlying buildings—Selected observations,implications and considerations

Vapor intrusion characterization and response efforts must consider four key interactive factors: background indoor air constituents, preferential vapor migration pathways, complex patterns of vapor distribution within buildings, and temporal concentration variability caused by pressure differentials within and exterior to structures. An additional challenge is found at sites contaminated by trichloroethylene (TCE), which in the United States has very low indoor air screening levels due to acute risk over short exposure durations for sensitive populations. Timely and accurate characterization of vapor intrusion has been constrained by traditional passive time‐averaging sampling methods. This article presents three case studies of a robust new methodology for vapor intrusion characterization particularly suited for sites where there is a critical need for rapid response to exposure exceedances to minimize health risks and liabilities. The new methodology comprises low‐detection‐level field analytical instrumentation with grab sample and continuous monitoring capabilities for key volatile constituents integrated with pressure differential measurements and web‐based reporting. The system also provides automated triggered alerts to project teams and capability for integration with engineered systems for vapor intrusion control. The three case studies illustrate key findings and lessons learned during system deployment at two sites undergoing characterization studies and one site undergoing thermal remediation of volatile contaminants.     

Cyclodextrin‐enhanced remediation of organic and metal contaminants in porous media and groundwater

Heavy metals and toxic organic contaminants are found at numerous industrial and military sites. The generally poor performance of conventional pump‐and‐treat schemes has made the development of improved methods for contaminated site remediation a significant environmental priority. One such innovative method is cyclodextrin‐enhanced flushing of the contaminated porous media and groundwater. Cyclodextrin is a glucose‐based molecule that is produced on industrial scales by microorganisms. Over the last years, several cyclodextrin derivatives have received extensive research interest. It was shown that cyclodextrins can significantly enhance the solubility of toxic organics, and in some cases, heavy metals and radioactive isotopes. As a sugar, cyclodextrin is considered relatively non‐toxic to humans, plants, and soil microbes. Thus, there are minimal health‐related concerns associated with the injection of cyclodextrin into the subsurface, which is an inherent advantage for use of cyclodextrins as a remediation agent. This paper provides a review of the available literature concerning use of cyclodextrin for remediation of groundwater and soil.     

Life‐cycle assessment of in situ thermal remediation

A detailed cradle‐to‐grave life‐cycle assessment (LCA) of an in situ thermal treatment remedy for a chlorinated‐solvent‐contaminated site was performed using process LCA. The major materials and activities necessary to install, operate, monitor, and deconstruct the remedy were included in the analysis. The analysis was based on an actual site remedy design and implementation to determine the potential environmental impacts, pinpoint major contributors to impacts, and identify opportunities for improvements during future implementation. The Electro‐Thermal Dynamic Stripping Process (ET‐DSP?) in situ thermal technology coupled with a dual‐phase extraction and treatment system was evaluated for the remediation of 4,400 yd³ of tetrachloroethene‐ and trichloroethene‐impacted soil, groundwater, and bedrock. The analysis was based on an actual site with an estimated source mass of 2,200 lbs of chlorinated solvents. The remedy was separated into four stages: remedy installation, remedy operation, monitoring, and remedy deconstruction. Environmental impacts were assessed using Sima Pro software, the ecoinvent database, and the ReCiPe midpoint and endpoint methods. The operation stage of the remedy dominated the environmental impacts across all categories due to the large amount of electricity required by the thermal treatment technology. Alternate sources of electricity could significantly reduce the environmental impacts of the remedy across all impact categories. Other large impacts were observed in the installation stage resulting from the large amount of diesel fuel, steel, activated carbon, and asphalt materials required to implement the technology. These impacts suggest where opportunities for footprint reductions can be found through best management practices such as increased materials reuse, increased recycled‐content materials use, and clean fuels and emission control technologies. Smaller impacts were observed in the monitoring and deconstruction stages. Normalized results show the largest environmental burdens to fossil depletion, human toxicity, particulate matter formation, and climate‐change categories resulting from activities associated with mining of fossil fuels for use in electricity production. In situ thermal treatment can reliably remediate contaminated source areas with contaminants located in low‐permeability zones, providing complete destruction of contaminants in a short amount of time, quick return of the site to productive use, and minimized quantities of hazardous materials stored in landfills for future generations to remediate. However, this remediation strategy can also result in significant emissions over a short period of time. It is difficult to quantify the overall value of short‐term cleanups with intense treatment emissions against longer‐term cleanups with lower treatment emissions because of the environmental, social, and economic trade‐offs that need to be considered and understood. LCA is a robust, quantitative tool to help inform stakeholder discussions related to the remedy selection process, trade‐off considerations, and environmental footprint‐reduction opportunities, and to complement a broader toolbox for the evaluation of sustainable remediation strategies. © 2012 Wiley Periodicals, Inc.     

Cost effectively decommissioning an automotive parts facility

Using a comprehensive approach to decommission a 180,000-square-foot automotive parts manufacturing facility saves time and money while reducing environmental liability. Prior to starting the facility decommissioning, a detailed facility characterization was conducted to identify contaminated areas. Remediation activities were scheduled to coincide with facility demolition. Specialized subcontractors were used to perform tasks such as asbestos and lead-paint abatement, soil bioremediation, underground storage tank and clarifier removal, and facility destruction and recycling. The project timetable was reduced by using several crews simultaneously to conduct recycling, demolition, and remediation. Costs were offset by selling remaining equipment, scrap metals, overhead lights and fixtures, and a premanufactured steel building. A total of 415 tons of scrap metal was recycled, not including the aforementioned steel building. On-site recycling and remediation were used wherever possible to reduce cost and associated hauling liabilities. For example, concrete and asphalt debris were crushed and used as base for final site paving, saving disposal costs and base material purchase costs. On-site bioremediation of soil impacted by perchloroethene (PCE) saved over $1.5 million, with total project savings of $2.4 million. On-site remediation and recycling also reduced both long-term and short-term environmental liability.     

Successful combination of remediation techniques at a former silver factory

A residential area that was formerly part of a silver factory site severely contaminated with chlorinated solvents was remediated using an in situ electro‐bioreclamation technique. Electro‐bioreclamation is a method for heating soil and groundwater combined with soil vapor and low‐yield groundwater extraction and enhanced reductive dechlorination (ERD). During the first two years of remediation in the source area (the intensive phase), a total of 80 kg of volatile organic compounds (VOCs) was removed by heating combined with ERD. After another two years of ERD in the source and plume areas (the attenuation phase), the VOC concentrations were reduced to a level below 100 μg/L in groundwater. Given these satisfying results, electro‐reclamation in combination with ERD turned out to be a successful in situ remediation technique for removing VOCs. © 2006Wiley Periodicals, Inc.     

Nature,frequency, and cost of environmental remediation at onshore oil and gas exploration and production sites

This article quantifies the nature, frequency, and cost of environmental remediation activities for onshore oil and gas operations, as determined from over 4,100 environmental remediation cases in Texas, Kansas, New Mexico, and Colorado. For the purpose of this article, “remediation'' refers to cleanup efforts that entail longer‐term site characterization, monitoring, and remedial action beyond the initial spill cleanup or emergency response stage. In addition, data are also presented regarding short‐term spill cleanup activities in two of the four states. © 2011 Wiley Periodicals, Inc.     

Evaluation of algal phytoremediation of light extractable petroleum hydrocarbons in subarctic climates

The presence of an organic mat in a hydrocarbon‐impacted creek in Whitehorse, Yukon Territory, Canada was examined for contributions to in situ remediation of petroleum‐contaminated water. This article investigates the role of algae, found in the organic mat, in the remediation of light extractable petroleum hydrocarbons (LEPHs) at the site and in the laboratory. During the study, LEPH concentrations were reduced by 16.8 percent in the presence of algae alone (algal solution) and 30.4 percent in the combined organic mat solution containing microbial consortia. The study results indicate that algal species at the site did not directly phytoremediate hydrocarbons. Rather, they were part of the total biological degradation taking place. © 2009 Wiley Periodicals, Inc.     

生物炭修复Cd,Pb污染土壤的研究进展

随着矿产开采、冶炼等工业活动以及污水灌溉、施用污泥和劣质化肥等农业活动的进行,Cd,Pb等有害重金属不断进入农业环境中,对农田、菜地等造成污染。生物炭作为重要的土壤改良剂,在对Cd,Pb污染土壤的修复中表现出巨大的潜力。从生物炭的特性及制备、修复效果及其影响因素、修复机理等方面,对近年来国内外有关生物炭修复Cd,Pb污染土壤的研究成果和现状进行了总结,并对生物炭修复Cd,Pb污染土壤的发展前景和未来研究方向进行了展望。     

Managing contaminated sites and the role of domestic and international forums

Domestic and international cooperation in the field of contaminated‐site management has increased dramatically in the past decade. The expected benefits of this cooperation include the reduction of duplication in remediation efforts, the coordination of contaminated‐site research, improved synergy between various stakeholders, enhanced policy development, and better information dissemination and technology transfer. This article identifies and briefly discusses key domestic and international collaborations, partnerships, and networks relating to contaminated‐site management and remediation. Also provided is information on how the forums can be accessed. Common themes identified across the forums discussed in this article include (1) the development and demonstration of innovative technologies, (2) the use of risk assessment, (3) the use of toxicology, bioavailability, and ecotoxicity testing, and (4) the increasing need to find holistic approaches for managing contaminated sites, such as guaranteed remediation programs and transfer of environment liability, and the need for understanding implications of remediation financing mechanisms. © 2001 John Wiley & Sons, Inc.     

Electroremediation part II: A study of the movement of heavy metals during an electroremediation process in Andisol soil

In the Summer 2004 issue of Remediation, the authors presented a study of the influence of buffering behavior in contaminated Andisol soil. This article, Part II, expands on this research by presenting the results of laboratory tests conducted to study the movement of heavy metals in contaminated Andisol soil during the first stage of an electrochemical remediation process. The analysis was performed on the soil after treatment and also on the washing solutions collected during the first four hours. In order to analyze the effectiveness of fast and simple techniques for monitoring the electroremediation process, computer‐aided modeling of speciation in the soil solution was performed in connection with the remediation treatment. The results show that the metals moved mainly as positive species in the soil and later occurred as insoluble forms relative to the pH value in the washing solution from the cathode chamber. © 2005 Wiley Periodicals, Inc.