A concentration correction scheme for Lagrangian particle model and its application in street canyon air dispersion modelling

Pollutant dispersion in street canyons with various configurations was simulated by discharging a large number of particles into the computation domain after developing a time-dependent wind field. Trajectory of the released particles was predicted using a Lagrangian particle model developed in an earlier study. A concentration correction scheme, based on the concept of “visibility”, was adopted for the Lagrangian particle model to correct the calculated pollutant concentration field in street canyons. The corrected concentrations compared favourably with those from wind tunnel experiments and a linear relationship between the computed concentrations and wind tunnel data were found. The developed model was then applied to four simulations to test for the suitability of the correction scheme and to study pollutant distribution in street canyons with different configurations. For those cases with obstacles presence in the computation domain, the correction scheme gives more reasonable results compared with the one without using it. Different flow regimes are observed in the street canyons, which depend on building configurations. A counter-clockwise rotating vortex may appear in a two-building case with wind flow from left to right, causing lower pollutant concentration at the leeward side of upstream building and higher concentration at the windward side of downstream building. On the other hand, a stable clockwise rotating vortex is formed in the street canyon with multiple identical buildings, resulting in poor natural ventilation in the street canyon. Moreover, particles emitted in the downstream canyon formed by buildings with large height-to-width ratios will be transported to upstream canyons.     

孤立与非孤立城市街道峡谷内污染物扩散

通过求解二维不可压N-S方程、k-ε方程及污染物对流扩散方程,模拟了孤立街道峡谷与非孤立街道峡谷内的流场及交通污染物浓度场.计算结果与风洞试验结果总体趋势一致.非孤立街道峡谷内污染物壁面浓度要大于孤立街道峡谷内的壁面浓度.通过计算街道峡谷建筑屋顶高度处的垂直方向污染物通量,说明了湍流扩散是污染物扩散出街道峡谷的主要原因,其污染物通量总为正,而平均流通量可以为负.非孤立街道峡谷由于平均流流动和湍流流动的总扩散通量减少,造成污染物在街道峡谷内集聚,从而理论上解释了非孤立街道峡谷与孤立街道峡谷污染扩散的差别.     

Removal of lead and zinc ions from aqueous solution using Amasya zeolites from Turkey

A 3-D Eulerian-Lagrangian approach to moving vehicles is presented that takes into account the traffic-induced flow rate and turbulence. The method is applied to pollutant dispersion in an individual street canyon and a system of two street canyons forming a perpendicular intersection. The approach is based on computational fluid dynamics (CFD) calculations using a Eulerian approach for continuous phase and a Lagrangian approach for moving vehicles. The wind speed was assigned values of 4, 7 and 12 m/s. One-way and two-way traffic with different traffic rates per lane is considered. In the case of the intersection, a longitudinal wind direction was assumed. Predictions show differences in the pollutant dispersion in the case of one-way and two-way traffic.     

Wind-tunnel study of concentration fields in street canyons

The paper presents results from a case study of gaseous pollutant dispersion in street canyons. Tracer-gas experiments were performed in a neutrally stratified wind tunnel. Vehicle emissions were simulated as line sources. Concentration profiles along building walls were measured. A two-dimensional street canyon was considered as the reference case. The influence of systematic parameter variations on the concentration field is studied and discussed. Building dimensions, upwind building configuration, wind direction and roof geometry were found to be important parameters. Data sets from the study may be used for evaluation of numerical models and for expert estimates of air quality in the urban environment     

A field study of factors influencing the concentrations of a traffic-related pollutant in the vicinity of a complex urban junction

The paper describes a field study focused on the dispersion of a traffic-related pollutant within an area close to a busy intersection between two street canyons in Central London. Simultaneous measurements of airflow, traffic flow and carbon monoxide concentrations ([CO]) are used to explore the causes of spatial variability in [CO] over a full range of background wind directions. Depending on the roof-top wind direction, evidence of both flow channelling and recirculation regimes were identified from data collected within the main canyon and the intersection. However, at the intersection, the merging of channelled flows from the canyons increased the flow complexity and turbulence intensity. These features, coupled with the close proximity of nearby queuing traffic in several directions, led to the highest overall time-average measured [CO] occurring at the intersection. Within the main street canyon, the data supported the presence of a helical flow regime for oblique roof-top flows, leading to increased [CO] on the canyon leeward side. Predominant wind directions led to some locations having significantly higher diurnal average [CO] due to being mostly on the canyon leeward side during the study period. For all locations, small changes in the background wind direction could cause large changes in the in-street mean wind angle and local turbulence intensity, implying that dispersion mechanisms would be highly sensitive to small changes in above roof flows. During peak traffic flow periods, concentrations within parallel side streets were approximately four times lower than within the main canyon and intersection which has implications for controlling personal exposure. Overall, the results illustrate that pollutant concentrations can be highly spatially variable over even short distances within complex urban geometries, and that synoptic wind patterns, traffic queue location and building topologies all play a role in determining where pollutant hot spots occur.     

Evaluation of traffic-producing turbulence schemes within Operational Street Pollution Models using roadside measurements

Low wind scenarios are associated with the worst air pollution episodes in urban street canyons. Under these conditions, operational dispersion models often over-predict pollutant concentration. Traffic-producing turbulence (TPT) becomes dominant in mixing and diluting traffic-related pollutants under low wind speed conditions. Determining the TPT effect on the flow and dispersion patterns within urban street canyons is crucial for the development of detailed operational dispersion models for assessing urban air quality. Several spatially averaged TPT formulations have been recently proposed in the literature. However, only a few attempts have been made so far to incorporate different TPT schemes into operational dispersion models and evaluate their performance using measurements.In this paper, several TPT schemes presented in literature were evaluated. Two TPT schemes were implemented in the well-validated Windows version of the Danish Operational Street Pollution Model (WinOSPM). Both formulations were evaluated using six independent datasets of roadside CO concentrations collected in European cities. Statistical and sensitivity analyses were undertaken to test the performance of the different formulations. The results showed that the overall model performance was significantly sensitive to the TPT schemes adopted. The model performance improved when a detailed characterisation of the TPT, depending on the density of road traffic, was used.     

Pollutant dispersion in urban street canopies

The effects of building configurations on pollutant dispersion around street canopies were studied numerically. The dispersion of pollutants emitted from ground sources was simulated by continuously discharging large number of particles into the computation domain. The mean wind velocities at each time-step were firstly computed by solving the time-dependent incompressible Navier–Stokes equations, while the fluctuated velocities were determined using a statistical procedure. The trajectories of the discharged particles were obtained from a Lagrangian particle model. Three categories of numerical simulation were conducted to study the effect of different canopy geometries on the pollutant dispersion. The computed wind field data were consistent with the wind field characteristics described in the previous wind tunnel studies. A counter-clockwise vortex was found resulting in high pollutant concentration at the windward side of the downstream building of the street canopy and low pollutant concentration at the leeward side of the upstream building. The increase in height of the urban roughness buildings would facilitate the pollutant dispersion in urban street canopy under certain building configurations. Two or more vortices stacked vertically in a street canopy were found when height of the upstream and downstream buildings of a street canopy was increased, preventing pollutants from escaping out of the canopy.     

Numerical modeling on air quality in an urban environment with changes of the aspect ratio and wind direction

Due to heavy traffic emissions within an urban environment, air quality during the last decade becomes worse year by year and hazard to public health. In the present work, numerical modeling of flow and dispersion of gaseous emissions from vehicle exhaust in a street canyon were investigated under changes of the aspect ratio and wind direction. The three-dimensional flow and dispersion of gaseous pollutants were modeled using a computational fluid dynamics (CFD) model which was numerically solved using Reynolds-averaged Navier–Stokes (RANS) equations. The diffusion flow field in the atmospheric boundary layer within the street canyon was studied for different aspect ratios (W/H?=?1/2, 3/4, and 1) and wind directions (θ?=?90°, 112.5°, 135°, and 157.5°). The numerical models were validated against wind tunnel results to optimize the turbulence model. The numerical results agreed well with the wind tunnel results. The simulation demonstrated that the minimum concentration at the human respiration height within the street canyon was on the windward side for aspect ratios W/H?=?1/2 and 1 and wind directions θ?=?112.5°, 135°, and 157.5°. The pollutant concentration level decreases as the wind direction and aspect ratio increase. The wind velocity and turbulence intensity increase as the aspect ratio and wind direction increase.     

Street canyon ventilation and atmospheric turbulence

Operational models for pollutant dispersion in urban areas require an estimate of the turbulent transfer between the street canyons and the overlying atmospheric flow. To date, the mechanisms that govern this process remain poorly understood. We have studied the mass exchange between a street canyon and the atmospheric flow above it by means of wind tunnel experiments. Fluid velocities were measured with a Particle Image Velocimetry system and passive scalar concentrations were measured using a Flame Ionisation Detector. The mass-transfer velocity between the canyon and the external flow has been estimated by measuring the cavity wash-out time. A two-box model, used to estimate the transfer velocity for varying dynamical conditions of the external flow, has been used to interpret the experimental data. This study sheds new light on the mechanisms which drive the ventilation of a street canyon and illustrates the influence of the external turbulence on the transfer process.     

Impact of building facades and ground heating on wind flow and pollutant transport in street canyons

This paper investigates the impacts of building facades and ground heating on the wind flow and pollutant transport in street canyons using the computational fluid dynamic (CFD) technique. Street canyons of H/W (H representing the building height and W the street width) varied from 0.1 to 2, which covered the basic flow regimes of skimming flow (H/W=1 or 2), wake interference flow (H/W=0.5), and isolated roughness flow (H/W=0.1), were examined in a series of sensitivity tests. Heating that occurred on different surfaces, including ground surface and building façades, posed considerable effects on the street canyon wind flow and pollutant transport compared with those under isothermal conditions. The CFD results showed that the mechanically induced wind flow and pollutant transport were complicated by the buoyancy under temperature stratification. Individual street canyons of different H/W and surface-heating scenarios exhibited their unique wind flow structure and pollutant transport behaviors. Two counter-rotating vortices were calculated in the street canyons of H/W=1, in which the zone of higher pollutant concentration under isothermal conditions was switched from the leeward side to the windward side. In the street canyon of H/W=2, the recirculating wind pattern was perturbed by surface heating that led to the development of either one primary vortex or three closely coupled vortices. Because of the complicated wind structure, the zones of higher pollutant concentration located either on the leeward or windward ground level were subjected to the surface-heating scenarios. Only two vortices were developed inside the street canyon of H/W=0.5. The large primary vortex, centered inside the street canyon, extended above the roof level of the street canyon. Meanwhile, a small secondary vortex was found at the ground-level windward corner whose size results as a function of surface-heating configurations. Finally, in the street canyon of H/W=0.1, an isolated clockwise-rotating vortex was developed beside the leeward building while the wind in the windward side blew in the prevailing wind direction. As a result, air pollutant emitted at the street centerline was unlikely to be carried into the leeward vortex. Instead, it was dispersed rapidly on the windward side before being removed from the street canyon.     

Assessing the representativeness of monitoring data from an urban intersection site in central London,UK

The wind flow field around urban street-building configurations has an important influence on the microscale pollutant dispersion from road traffic, affecting overall dilution and creating localised spatial variations of pollutant concentration. As a result, the “representativeness” of air quality measurements made at different urban monitoring sites can be strongly dependent on the interaction of the local wind flow field with the street-building geometry surrounding the monitor. The present study is an initial attempt to develop a method for appraising the significance of air quality measurements from urban monitoring sites, using a general application computational fluid dynamics (CFD) code to simulate small-scale flow and dispersion patterns around real urban building configurations. The main focus of the work was to evaluate routine CO monitoring data collected by Westminster City Council at an intersection of street canyons at Marylebone Road, Central London. Many monitors in the UK are purposely situated at urban canyon intersections, which are thought to be local “hot spots” of pollutant emissions, however very limited information exists in the literature on the flow and dispersion patterns associated with them. With the use of simple CFD simulations and the analysis of available monitoring data, it was possible to gain insights into the effect of wind direction on the small-scale dispersion patterns at the chosen intersection, and how that can influence the data captured by a monitor. It was found that a change in wind direction could result in an increase or decrease of monitored CO concentration of up to 80%, for a given level of traffic emissions and meteorological conditions. Understanding and de-coupling the local effect of wind direction from monitoring data using the methods presented in this work could prove a useful new tool for urban monitoring data interpretation.     

Effects of Strength and Position of Pollutant Source on Pollutant Dispersion Within an Urban Street Canyon

A two-dimensional numerical model for simulating airflow and pollutant dispersion inside an urban street canyon was first developed using the FLUENT code, and then it was validated against a wind tunnel experiment. Then the effects of strength and position of pollutant sources on pollutant dispersion within an urban street canyon were investigated numerically. The numerical results showed that the dimensionless pollutant concentrations within the urban street canyon were independent from the source strength. The results also revealed that the pollutant distributions inside the urban street canyon with a two-lane road were influenced significantly by the positions of the two sources: 1) the closer the two sources were to the street center of the canyon, the lower the pollutant concentrations on the leeward wall and at the human respiration level in the leeward footpath became; 2) the pollutant concentrations on the windward wall and at the human respiration level in the windward footpath were not sensitive to the locations of the two sources as long as the source on the windward lane was situated outside the small recirculation zone at the bottom corner of the canyon windward wall; 3) the pollutant concentrations on the lower parts of the windward and leeward walls as well as in the two footpaths increased greatly when the two sources were moved from outside into the small recirculation zones.     

Lagrangian dispersion modeling of vehicular emissions from a highway in complex terrain

Transit traffic through the Austrian Alps is of major concern in government policy. Pollutant burdens resulting from such traffic are discussed widely in Austrian politics and have already led to measures to restrict traffic on transit routes. In the course of an environmental assessment study, comprehensive measurements were performed. These included air quality observations using passive samplers, a differential optical absorption spectroscopy system, a mobile and a fixed air quality monitoring station, and meteorological observations. As was evident from several previous studies, dispersion modeling in such areas of complex terrain and, moreover, with frequent calm wind conditions, is difficult to handle. Further, in the case presented here, different pollutant sources had to be treated simultaneously (e.g., road networks, exhaust chimneys from road tunnels, and road tunnel portals). No appropriate system for modeling all these factors has so far appeared in the literature. A prognostic wind field model coupled with a Lagrangian dispersion model is thus presented here and is designed to treat all these factors. A comparison of the modeling system with results from passive samplers and from a fixed air quality monitoring station proved the ability of the model to provide reasonable figures for concentration distributions along the A10.     

Screening and Scenarios of Traffic Emissions at Trier,Germany

SCOPE AND BACKGROUND: In the course of the European Council Directive on permissible air pollutant limit values, valid starting from 2005 there is an urgent call for action, particularly for fine dust (PM10). Current investigations (Junk & Helbig 2003, Reuter & Baumüller 2003) show that the limit values in certain places in congested areas are exceeded. Only if it is possible to locate these Hot Spots purposeful measures to reduce the ambient air pollution can be conducted. For an efficient identification of these Hot Spots numerical computer models or establishing special measurements networks are too expensive. Using the statistical model STREET 5.0 (KTT 2003) a cost-effective screening of the air pollution situation caused by the traffic can be done. METHODS: STREET is based on the 3-dimensional micro-scale non-hydrostatic flow- and dispersion model MISCAM (Eichhorn 1989). The results of over 100.000 different calculations with MISCAM are stored in a Database and used to calculate the emissions with STREET. In collaboration with the city council of Trier more than 150 streets were investigated, mapped, and calculated. A special urban climate measuring network supplies the necessary meteorological input data about the wind field and precipitation events in the valley of the Moselle. Information about road width and road orientation as well as building density was derived from aerial photographs. Traffic censuses and mobile air pollutants measurements supplied the remaining input data. We calculated the mean annual air pollutant concentrations for NO2, CO, SO2, O3, benzene as well as PM10. RESULTS: A comparison of the model results with the values obtained from the stations of the central emission measuring network of Rhineland-Palatinate (ZIMEN, annual report 2002) shows very good agreements. The model was not only used to calculate the annual air pollutant but also for urban planning and management. The absolute level of the air pollutant is mainly dependent on the amount of traffic in the street canyons. Therefore four different case-scenarios with varying quantity of traffic were calculated and interpreted for each street. The results of the calculation show that on the basis of the mean values for both NO2 and benzene, it is not to be expected that the limits PERSPECTIVES: Furthermore the model can be used to find the maximum tolerable numbers of cars for a street without exceeding the air pollutant thresholds.     

Lagrangian Dispersion Modeling of Vehicular Emissions from a Highway in Complex Terrain

Abstract

Transit traffic through the Austrian Alps is of major concern in government policy. Pollutant burdens resulting from such traffic are discussed widely in Austrian politics and have already led to measures to restrict traffic on transit routes. In the course of an environmental assessment study, comprehensive measurements were performed. These included air quality observations using passive samplers, a differential optical absorption spectroscopy system, a mobile and a fixed air quality monitoring station, and meteorological observations. As was evident from several previous studies, dispersion modeling in such areas of complex terrain and, moreover, with frequent calm wind conditions, is difficult to handle. Further, in the case presented here, different pollutant sources had to be treated simultaneously (e.g., road networks, exhaust chimneys from road tunnels, and road tunnel portals). No appropriate system for modeling all these factors has so far appeared in the literature. A prognostic wind field model coupled with a Lagrangian dispersion model is thus presented here and is designed to treat all these factors. A comparison of the modeling system with results from passive samplers and from a fixed air quality monitoring station proved the ability of the model to provide reasonable figures for concentration distributions along the A10.     

Operational air pollution modelling in the UK—Street canyon applications and challenges

Local air quality management requires the use of screening and advanced modelling tools that are able to predict roadside pollution levels under a variety of meteorological and traffic conditions. So far, more than 200 air pollution hotspots have been identified by local authorities in the UK, many of them associated with NO₂ and/or PM₁₀ exceedences in heavily trafficked urban streets that may be classified as street canyons or canyon intersections. This is due to the increased traffic-related emissions and reduced natural ventilation in such streets. Specialised dispersion models and empirical adjustment factors have been commonly used to account for the entrapment of pollutants in street canyons. However, most of the available operational tools have been validated using experimental datasets from relatively deep canyons (H/W⩾1) from continental Europe. The particular characteristics of low-rise street canyons (H/W<1), which are a typical feature of urban/sub-urban areas in the UK, have been rarely taken into account.The main objective of this study is to review current practice and evaluate three widely used regulatory dispersion models, WinOSPM, ADMS-Urban 2.0 and AEOLIUS Full. The model evaluation relied on two comprehensive datasets, which included CO, PM₁₀ and NO_x measurements, traffic information and relevant meteorological data from two busy street canyons in Birmingham and London for a 1-year period. The performance of the selected models was tested for different times of the day/days of the week and varying wind conditions. Furthermore, the ability of the models to reproduce roadside NO₂/NO_x concentration ratios using simplified chemistry schemes was evaluated for one of the sites. Finally, advantages and limitations of the current regulatory street canyon modelling practice in the UK, as well as needs for future research, have been identified and discussed.     

A comprehensive experimental databank for the models verification of urban car emission dispersion

A summary presentation is made of representative samples from a comprehensive experimental databank on car exhaust dispersion in urban street canyons. Physical modelling, under neutral stratification conditions, was used to provide visualisation, pollutant concentration and velocity measurements above and inside test canyons amidst surrounding urban roughness. The study extended to two different canyon aspects ratios, in combination with different roof configurations on the surrounding buildings. To serve as a reliable basis for validation and testing of urban pollution dispersion codes, special emphasis was placed in this work on data quality assurance.     

The effects of roadside structures on the transport and dispersion of ultrafine particles from highways

Understanding local-scale transport and dispersion of pollutants emitted from traffic sources is important for urban planning and air quality assessments. Predicting pollutant concentration patterns in complex environments depends on accurate representations of local features (e.g., noise barriers, trees, buildings) affecting near-field air flows. This study examined the effects of roadside barriers on the flow patterns and dispersion of pollutants from a high-traffic highway in Raleigh, North Carolina, USA. The effects of the structures were analyzed using the Quick Urban & Industrial Complex (QUIC) model, an empirically based diagnostic tool which simulates fine-scale wind field and dispersion patterns around obstacles. Model simulations were compared with the spatial distributions of ultrafine particles (UFP) from vehicular emissions measured using a passenger van equipped with a Differential Mobility Analyzer/Condensation Particle Counter. The field site allowed for an evaluation of pollutant concentrations in open terrain, with a noise barrier present near the road, and with a noise barrier and vegetation present near the road.Results indicated that air pollutant concentrations near the road were generally higher in open terrain situations with no barriers present; however, concentrations for this case decreased faster with distance than when roadside barriers were present. The presence of a noise barrier and vegetation resulted in the lowest downwind pollutant concentrations, indicating that the plume under this condition was relatively uniform and vertically well-mixed. Comparison of the QUIC model with the mobile UFP measurements indicated that QUIC reasonably represented pollutant transport and dispersion for each of the study configurations.     

Minimizing the effect of automotive pollution in urban geometry using mathematical optimization

One of the factors that needs to be considered during the layout of new urban geometry (e.g. street direction, spacing and width, building height restrictions) is the effect of the air pollution associated with the automotive transport that would use routes in this urban area. Although the pollution is generated at street level, its effect can be widespread due to interaction of the pollutant dispersion and diffusion with the wind speed and direction. In order to study the effect of a new urban geometry on the pollutant levels and dispersion, a very time-consuming experimental or parametric numerical study would have to be performed. This paper proposes an alternative approach, that of combining mathematical optimization with the techniques of computational fluid dynamics (CFD). In essence, the meteorological information as represented by a wind rose (wind speed and direction), is used to calculate pollutant levels as a function of urban geometry variables: street canyon depth and street canyon width. The pollutant source specified in conjunction with a traffic scenario with CO is used as pollutant. The main aim of the study is to be able to suggest the most beneficial configuration of an idealized urban geometry that minimizes the peak pollutant levels due to assumed traffic distributions. This study uses two mathematical optimization methods. The first method is implemented through a successive maximization–minimization approach, while the second method determines the location of saddle points of the pollutant level, considered as a function of urban geometry and wind rose. Locally, a saddle point gives the best urban geometry for the worst meteorological scenario. The commercial CFD code, STAR-CD, is coupled with a version of the DYNAMIC-Q optimization algorithm of Snyman, first to successively locate maxima and minima in a min–max approach; and then to locate saddle points. It is shown that the saddle-point method is more cost-effective. The methodology presented in this paper can readily be extended to optimize traffic patterns for existing geometry or in the development of geometry modification for pollution control or toxic releases.     

Active moss biomonitoring of small-scale spatial distribution of airborne major and trace elements in the Belgrade urban area

In urban environments, human exposure to air pollutants is expected to be significantly increased, especially near busy traffic streets, street canyons, tunnels, etc. where urban topography and microclimate may additionally cause poor air conditions giving rise to pollution hotspots. As a practical and cost-effective approach, active moss biomonitoring survey of some major and trace element air pollution was performed in the Belgrade street canyons and city tunnel in 2011 with the aim to evaluate possibility of using Sphagnum girgensohnii moss bags for investigation of the small-scale vertical and horizontal distribution patterns of the elements. In five street canyons, the moss bags were hung at heights of about 4, 8 and 16 m, during 10 weeks, and also, for the same time, the moss bags were exposed in the tunnel, in front of and out of it. After the exposure period, the concentrations of Al, Ba, Ca, Cd, Co, Cr, Cu, Fe, K, Mg, Mn, Na, Ni, Pb, Sr, V and Zn in the moss were determined by inductively coupled plasma optical emission spectrometry. According to the results, in all street canyons, the vertical distribution patterns of the moss elements concentration (Al, Ba, Co, Cr, Cu, Ni, Pb, Sr, V and Zn) showed statistically significant decrease from the first to the third heights of bags exposure. In the tunnel experiment, from inner to out of the tunnel, for Al, Ba, Cd, Co, Cr, Cu, Fe, K and Zn, decreasing trend of concentrations was obtained. Significantly higher concentration of the elements was pronounced for the tunnel in comparison with the street canyons. The results indicate that the use of S. girgensohnii moss bags is a simple, sensitive and inexpensive way to monitor the small-scale inner city spatial distribution of airborne major and trace element content.